Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Mechanical characterization of 304L-VAR stainless steel in tension with a full coverage of low, intermediate, and high strain rates

A 304L-VAR stainless steel is mechanically characterized in tension over a full range of strain rates from low, intermediate, to high using a variety of apparatuses. While low- and high-strain-rate tests are conducted with a conventional Instron and a Kolsky tension bar, the tensile tests at intermediate strain rates are conducted with a fast MTS and a Drop-Hopkinson bar. The fast MTS used in this study is able to obtain reliable tensile response at the strain rates up to 150 s -1 , whereas the lower limit for the Drop-Hopkinson bar is 100 s -1 . Combining the fast MTS and the Drop-Hopkinson bar closes the gap within the intermediate strain rate regime. Using these four apparatuses, the tensile stress-strain curves of the 304L-VAR stainless steel are obtained at strain rates on each order of magnitude ranging from 0.0001 to 2580 s -1 . All tensile stress-strain curves exhibit linear elasticity followed by significant work hardening prior to necking. After necking occurrs, the specimen load decreases, and the deformation becomes highly localized until fracture. The tensile stress-strain response of the 304L-VAR stainless steel exhibits strain rate dependence. The flow stress increases with increasing strain rate and is described with a power law. The strain-rate sensitivity is also strain-dependent, possibly due to thermosoftening caused by adiabatic heating at high strain rates. The 304L-VAR stainless steel shows significant ductility. The true strains at the onset of necking and at failure are determined. The results show that the true strains at both onset of necking and failure decrease with increasing strain rate. The true failure strains are approximately 200% at low strain rates but are significantly lower (~100%) at high strain rates. The transition of true failure strain occurs within the intermediate strain rate range between 10 -2 and 10 2 s -1 . A Boltzmann description is used to present the effect of nominal strain rate on true failure strain.

304L-VAR stainless Steel↗

Dislocation density-based plasticity model from massive discrete dislocation dynamics database

In this work, we present a dislocation density-based strain hardening model for single crystal copper through a systematic coarse-graining analysis of more than 200 discrete dislocation dynamics (DDD) simulations of plastic deformation under uniaxial tension. The proposed constitutive model has two components: a generalized Taylor relation connecting resolved shear stresses to dislocation densities on individual slip systems, and a generalized Kocks-Mecking model for dislocation multiplication. The DDD data strongly suggests a logarithmic dependence of flow stress on the plastic shear strain rate on each slip system, and, equivalently, an exponential dependence of the plastic shear strain rate on the resolved shear stress. Hence the proposed generalized Taylor relation subsumes the Orowan relation for plastic flow. The DDD data also calls for a correction to the Kocks-Mecking model of dislocation multiplication to account for the increase of dislocation density on slip systems with negligible plastic shear strain rate. This is accomplished by allowing the multiplication rate on each slip system to include contributions from the plastic strain rates of the two coplanar slip systems. The resulting constitutive model successfully captures the strain hardening rate dependence on the loading orientation as predicted by the DDD simulations, which is also consistent with existing experiments.

36 MATERIALS SCIENCE↗

On explicit algebraic stress models for complex turbulent flows

Explicit algebraic stress models that are valid for three-dimensional turbulent flows in noninertial frames are systematically derived from a hierarchy of second-order closure models. This represents a generalization of the model derived by Pope who based his analysis on the Launder, Reece, and Rodi model restricted to two-dimensional turbulent flows in an inertial frame. The relationship between the new models and traditional algebraic stress models -- as well as anistropic eddy visosity models -- is theoretically established. The need for regularization is demonstrated in an effort to explain why traditional algebraic stress models have failed in complex flows. It is also shown that these explicit algebraic stress models can shed new light on what second-order closure models predict for the equilibrium states of homogeneous turbulent flows and can serve as a useful alternative in practical computations.

Gatski, T. B.↗

The Relation Between Alloy Chemistry and Hot-Cracking

Hot cracking is a problem in welding 2195 aluminum-lithium alloy. Weld wire additives seem to reduce the problem. This study proposes a model intended to clarify the way alloying elements affect hot-cracking. The brittle temperature range of an alloy extends wherever the tensile stress required to move the meniscus of the liquid film at the grain/dendrite boundaries is less than the bulks flow stress Sigma(sub B) of the grains: 2gamma/delta <= sigma(sub B) + P where gamma is boundary film surface tension delta= boundary film thickness P = gas pressure (Some alloys outgas.) If the above condition is not met, the grains deform under stress and the liquid film remains in place. Curves of 2gamma/delta and sigma(sub B) vs. temperature in the range just below the melting temperature determine the hot cracking susceptibility of an alloy. Both are zero at onset of solidification. sigma(sub B) rises as the thermal activation of the slip mechanism is reduced. 2gamma/delta rises as the film thickness delta which can be estimated from the Scheil equation, drops. But, given an embrittled alloy, whether the alloy actually cracks is determined by the strain imposed upon it in the embrittled condition. A critical strain is estimated, Epsilon(sub C) on the order of Epsilon(sub C) is approximately delta/l where L = grain size and where the the volume increment due to the strain, concentrated at the liquid film, is on the order of the liquid film volume. In the early 80's an empirical critical strain cracking envelope Epsilon(sub C)(T) was incorporated into a damage criterion to estimate the effect of welding parameters on the formation of microfissures in a superalloy with good results. These concepts, liquid film decoherence vs. grain bulk deformation and critical strain, form the key elements of a quantitative theory of hot-cracking applicable for assessing the effect of alloying elements on hot-cracking during welding.

Nunes, A. C., Jr.↗

Physics-Based Modeling and Simulation of Self-Reacting Friction Stir Welding Using Computational Fluid Dynamics

A physics-based model was developed to simulate the behavior of material in a self-reacting friction stir welding (SR-FSW) process for the joining of metals. This steady-state model builds upon fundamental computational fluid dynamic (CFD) principles within Ansys Fluent to solve the discretized equations. The effective viscosity is calculated using a viscoplastic model using a Sheppard-Wright formulation of flow stress. Numerous advancements have been made in the incorporated physics including (1) temperature-dependent material properties; (2) locally adaptable flow and thermal boundary conditions; and (3) adapting material properties in nugget in response to microstructural changes. Simulation strategies to accelerate computation and improve numerical stability include adapting the mesh refinement and solver relaxation factors during simulation. The result is a highly robust and computationally efficient model capable of providing the material flow and temperature history across the domain. As material history determines the local microstructure and ultimately weld strength, an accurate and detailed physics-based model has the potential to accelerate SR-FSW process development. The model is highly adaptable to changes in process parameters, tool design, or alloy.

Process Modeling↗

Two modes of screw dislocation glide in fcc single-phase concentrated alloys

Concentrated solid solution alloys (CSSAs), including medium- and high-entropy alloys, are currently being considered as prospective materials in many applications. The behavior of CSSAs under different conditions, including mechanical loading, differs from that of conventional alloys and has been the subject of intensive study by different techniques. In many cases, their behavior is treated by modifying solid solution hardening models, which, in principle, does not reflect many important features of CSSAs where the distinction between solute and solvent atoms is not clear. In this work, we report the results of an atomic-scale study of ½<110>{111} screw dislocation motion in an fcc equiatomic Ni-Fe alloy. Molecular dynamics simulations demonstrate that the dislocation has two distinctive modes for glide. At lower stress, dislocations move in a very rough manner that cannot be described as continuous glide but rather as jerky motion through a set of obstacles. At high stress, they glide in a manner similar to lattice friction-controlled conditions in single component systems. The stress for the transition between modes depends on the dislocation segment length and temperature. As a result, at 300 K, the flow stress saturates at ~130 MPa for lengths above ~140 |b| (b is the Burgers vector).

36 MATERIALS SCIENCE↗

Virtual texture analysis to understand microstructure effects on deformation twinning and detwinning behavior in BCC metals

Understanding and predicting deformation twinning contributions to plastic deformation in BCC metals has been a long-standing challenge due to the interplay with dislocation slip and non-Schmid effects that render an asymmetry under tension and compression. This paper uses molecular dynamics simulations to understand the effect of unloading and grain orientation on deformation twinning in a nanocrystalline Fe (nc-Fe) system as a model BCC metal. The nc-Fe system is loaded under uniaxial stress tension and compression to understand the effect of grain orientation (Schmid effects) on deformation twinning behavior and the tension/compression asymmetry (non-Schmid effects). A new virtual texture analysis “VirTex” tool is used to understand the role of grain orientation on the nucleation of twins and their contributions to the observed stress–strain response. For certain grain orientations, the twinnability is observed to be different in tension and compression. In addition, the flow stress accommodation from twins in certain grains is observed to be different in tension and compression and different from that for the grains. Subsequent unloading leads to detwinning in the deformed microstructures, where the extent of detwinning depends on the strain from which the system is unloaded and on the morphology of the twin. Lastly, the simulations are carried out to analyze the role of the Schmid factor on the twinnability and asymmetry in tension and compression.

Kannan, Aadhithyan [University of Connecticut, Sto↗

Strength, plasticity, and spin transition of Fe-N compounds in planetary cores

Elastic and plastic properties of Fe-light element alloys and compounds are needed to determine the compositions and dynamics of planetary cores. Elastic strength and plastic deformation mechanisms and their relationship to electronic properties of ε-Fe 7 N 3 and γ’-Fe 4 N mixture were investigated by x-ray diffraction and x-ray emission spectroscopy in the diamond anvil cell from 1 bar up to 60 GPa. X-ray diffraction shows that ε-Fe 7 N 3 reaches a pressure of 15–20 GPa before undergoing bulk plasticity at a differential stress of 4.4–10.4 GPa. ε-Fe 7 N 3 is stronger than γ’-Fe 4 N and hcp-Fe which achieve a flow stress of 1.5–3.6 GPa at 10–15 GPa and 2–3 GPa at ~20 GPa, respectively. X-ray emission spectroscopy shows that a decrease in electronic spin moment begins before and completes after plastic flow onset for each nitride, suggesting that pressure-driven changes in electronic arrangement do not trigger a plastic response although they may modify the strength and plastic behavior of Fe-N compounds. Plastic deformation in ε-Fe 7 N 3 and hcp-Fe results in a preferred orientation of (0001) normal to maximum compression, while γ’-Fe 4 N develops a maximum in the (110). Furthermore, these observations may be combined with measurements of elasticity to model seismic properties of cores of small planetary bodies such as Mars, Mercury, and the Moon.

58 GEOSCIENCES↗

Probing the limits of metal plasticity with molecular dynamics simulations

Ordinarily, the strength and plasticity properties of a metal are defined by dislocations—line defects in the crystal lattice whose motion results in material slippage along lattice planes. Dislocation dynamics models are usually used as mesoscale proxies for true atomistic dynamics, which are computationally expensive to perform routinely. However, atomistic simulations accurately capture every possible mechanism of material response, resolving every “jiggle and wiggle” of atomic motion, whereas dislocation dynamics models do not. We present fully dynamic atomistic simulations of bulk single-crystal plasticity in the body-centred-cubic metal tantalum. Our goal is to quantify the conditions under which the limits of dislocation-mediated plasticity are reached and to understand what happens to the metal beyond any such limit. In our simulations, the metal is compressed at ultrahigh strain rates along its [001] crystal axis under conditions of constant pressure, temperature and strain rate. To address the complexity of crystal plasticity processes on the length scales (85–340 nm) and timescales (1 ns–1μs) that we examine, we use recently developed methods of in situ computational microscopy to recast the enormous amount of transient trajectory data generated in our simulations into a form that can be analysed by a human. Our simulations predict that, on reaching certain limiting conditions of strain, dislocations alone can no longer relieve mechanical loads; instead, another mechanism, known as deformation twinning (the sudden re-orientation of the crystal lattice), takes over as the dominant mode of dynamic response. Below this limit, the metal assumes a strain-path-independent steady state of plastic flow in which the flow stress and the dislocation density remain constant as long as the conditions of straining thereafter remain unchanged. In this distinct state, tantalum flows like a viscous fluid while retaining its crystal lattice and remaining a strong and stiff metal.

36 MATERIALS SCIENCE↗

Variability of plasma sheet dynamics

IMP 7 observations of plasma sheet structure and dynamics made during a 24-h period in which the satellite traversed the tail plasma sheet at a radial distance of 35 earth radii and remained within 2 earth radii of the expected position at the neutral sheet and in which at least five substorms occured on the ground are presented. High-time-resolution measurements of the magnetic field, plasma flow and greater than 50-keV protons obtained by the satellite and ground-based magnetic measurements are discussed for a 4-hr interval in which two small substorms occurred, a 6-hr geomagnetically quiet interval in which moderate variable plasma flows were observed, a very rapid, smooth neutral sheet crossing and earthward plasma flow during the expansion phase of a small substorm, a moderate-size substorm in which a prolonged interval of field-aligned tailward flow commenced at onset, a strong tailward and dawnward flow burst in an interval between substorms and a large substorm in which strong tailward flow was observed. Observations indicate the significant distortion of the tail field, possibly by plasma flow stresses, a neutral sheet structure occasionally resembling the hydromagnetic rotational discontinuity and a high level of magnetic turbulence during an earthward plasma flow which may contribute towards plasma sheet dissipation.

Coroniti, F. V.↗

Ultrahigh strength and plasticity in laser rapid solidified Al–Si nanoscale eutectics

As-cast Al–20wt.% Si alloys were processed via laser rapid solidification (LRS) techniques to create eutectic microstructures with nanoscale interconnected, nanotwinned Si fibers. LRS morphologies exhibit higher flow stress, exceeding 800 MPa and uniform plastic deformation above 20% compared to as-cast alloy that fractures at strains below 8% at flow strength of approximately 200 MPa. The strengthening mechanisms of LRS morphologies are interpreted in terms of the interfacial constraints: increase in yield strength as well as strain hardening rate due to nanoscale confined slip in fibrous Al–Si eutectic, and load transfer and eventual plasticity in the nanoscale Si fibers.

36 MATERIALS SCIENCE↗

Calculation of turbulent shear stress in supersonic boundary layer flows

Turbulent shear stress distributions for supersonic boundary layer flows have been computed from experimental mean boundary layer data. The computations have been made by numerically integrating the time averaged continuity and streamwise momentum equations. Distributions have been obtained for flows upstream and downstream of shock-wave-boundary layer interactions and for both two-dimensional and axisymmetric flows. The computed results are compared with recently reported shear stress measurements which were obtained by hot wire anemometer and laser velocimeter techniques.

Sun, C. C.↗

Plastic deformation of single crystals of the equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy in tension and compression from 10 K to 1273 K

In this report the plastic deformation behavior of single crystals of the quinary, equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy (HEA) with the face-centered cubic structure has been investigated in tension and compression as a function of crystal orientation and temperature from 10 K to 1373 K. The critical resolved shear stress (CRSS) for {111}<110> slip at room temperature is 42-45 MPa. It does not depend much on crystal orientation (i.e., the Schmid law holds true) and the sense (tension vs. compression) of the applied load. The CRSS for {111}<110> slip increases with the decrease in temperature, without showing any significant inertia effects at cryogenic temperatures below 77 K. Extrapolation from the measured yield stresses down to 10 K yields a CRSS value at 0 K of 168 MPa. At cryogenic temperatures, the measured strain-rate sensitivity of flow stress is consistent with a very small activation volume. The concept of stress equivalence holds true both for the temperature dependence of CRSS and the stress dependence of activation volume, indicating that solid-solution hardening is the major strengthening mechanism. Deformation twinning occurs at 77 K but not at room temperature, resulting in higher tensile elongation to failure at 77 K than at room temperature. Deformation twinning at 77 K occurs at a shear stress of 378 MPa on conjugate ($\bar1\bar11$) planes in the form of Lüders deformation after large plastic strain (about 85%) achieved by the stage I (easy glide) and stage II (linear work-hardening) deformation.

36 MATERIALS SCIENCE↗

Temperature Dependence of the Mechanical Properties of Equiatomic Solid Solution Alloys with FCC Crystal Structures

We found that compared to decades-old theories of strengthening in dilute solid solutions, the mechanical behavior of concentrated solid solutions is relatively poorly understood. A special subset of these materials includes alloys in which the constituent elements are present in equal atomic proportions, including the high-entropy alloys of recent interest. A unique characteristic of equiatomic alloys is the absence of “solvent” and “solute” atoms, resulting in a breakdown of the textbook picture of dislocations moving through a solvent lattice and encountering discrete solute obstacles. Likewise, to clarify the mechanical behavior of this interesting new class of materials, we investigate here a family of equiatomic binary, ternary and quaternary alloys based on the elements Fe, Ni, Co, Cr and Mn that were previously shown to be single-phase face-centered cubic (fcc) solid solutions. The alloys were arc-melted, drop-cast, homogenized, cold-rolled and recrystallized to produce equiaxed microstructures with comparable grain sizes. Tensile tests were performed at an engineering strain rate of 10 -3 s -1 at temperatures in the range 77–673 K. Unalloyed fcc Ni was processed similarly and tested for comparison. The flow stresses depend to varying degrees on temperature, with some (e.g. NiCoCr, NiCoCrMn and FeNiCoCr) exhibiting yield and ultimate strengths that increase strongly with decreasing temperature, while others (e.g. NiCo and Ni) exhibit very weak temperature dependencies. Moreover, to better understand this behavior, the temperature dependencies of the yield strength and strain hardening were analyzed separately. Lattice friction appears to be the predominant component of the temperature-dependent yield stress, possibly because the Peierls barrier height decreases with increasing temperature due to a thermally induced increase of dislocation width. In the early stages of plastic flow (5–13% strain, depending on material), the temperature dependence of strain hardening is due mainly to the temperature dependence of the shear modulus. In all the equiatomic alloys, ductility and strength increase with decreasing temperature down to 77 K. Keywords

36 MATERIALS SCIENCE↗

The turbulent mean-flow, Reynolds-stress, and heat flux equations in mass-averaged dependent variables

The time-dependent, turbulent mean-flow, Reynolds stress, and heat flux equations in mass-averaged dependent variables are presented. These equations are given in conservative form for both generalized orthogonal and axisymmetric coordinates. For the case of small viscosity and thermal conductivity fluctuations, these equations are considerably simpler than the general Reynolds system of dependent variables for a compressible fluid and permit a more direct extension of low speed turbulence modeling to computer codes describing high speed turbulence fields.

Rubesin, M. W.↗

Strain-rate/temperature behavior of high density polyethylene in compression

The compressive strain rate/temperature behavior of highly linear, high density polyethylene was analyzed in terms of the predictive relations developed for metals and other crystalline materials. For strains of 5 percent and above, the relationship between applied strain rate, dotted epsilon, and resulting flow stress, sigma, was found to be: dotted epsilon exp times (Q sub f/RT) = k'(sigma/sigma sub c) to the nth power; the left-hand side is the activation-energy-compensated strain rate, where Q sub f is activation energy for flow, R is gas constant, and T is temperature; k is a constant, n is temperature-independent stress exponent, and sigma/sigma sub c is structure-compensated stress. A master curve resulted from a logarithmic plot of activation-energy-compensated strain rate versus structure-compensated stress.

Clements, L. L.↗

FY12-Q3 National Risk Assessment Partnership (NRAP): Industrial Carbon Capture Program (Quarterly Report for LANL Activities)

This report summarizes progress of LANL activities related to the tasks performed under the LANL FWP FE102-002-FY10, National Risk Assessment Partnership (NRAP): Industrial Carbon Capture Program. This FWP is funded through the American Recovery and Reinvestment Act (ARRA). Overall, the NRAP activities are focused on understanding and evaluating risks associated with large-scale injection and long-term storage of CO 2 in deep geological formations. One of the primary risks during large-scale injection is due to changes in geomechanical stresses to the storage reservoir, to the caprock/seals and to the wellbores. These changes may have the potential to cause CO 2 and brine leakage and geochemical impacts to the groundwater systems. While the importance of these stresses is well recognized, there have been relatively few quantitative studies (laboratory, field or theoretical) of geomechanical processes in sequestration systems. In addition, there are no integrated studies that allow evaluation of risks to groundwater quality in the context of CO 2 injection-induced stresses. The work performed under this project is focused on better understanding these effects. LANL approach will develop laboratory and computational tools to understand the impact of CO 2 -induced mechanical stress by creating a geomechanical test bed using inputs from laboratory experiments, field data, and conceptual approaches. The Geomechanical Test Bed will be used for conducting sensitivity and scenario analyses of the impacts of CO 2 injection. The specific types of questions will relate to fault stimulation and fracture inducing stress on caprock, changes in wellbore leakage due to evolution of stress in the reservoir and caprock, and the potential for induced seismicity. In addition, the Geomechanical Test Bed will be used to investigate the coupling of stress-induced leakage pathways with impacts on groundwater quality. LANL activities are performed under two tasks: 1) develop laboratory and computational tools to understand CO 2 -induced mechanical impacts and 2) use natural analog sites to determine potential groundwater impacts. We are using the Springerville-St. John Dome as a field site for collecting field data on CO 2 migration through faults and groundwater impacts as well as developing and validating computational models. During the FY12 fourth quarter we received the tri-axial core-holder from New England Research Company (NERC). We have completed the construction of the experimental set up for performing coupled flow-stress experiments. We will be completing first set of flow through experiments in October.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Scale bridging damage model for quasi-brittle metals informed with crack evolution statistics

Computationally efficient methods for bridging length scales, from highly resolved micro/meso-scale models that can explicitly model crack growth, to macro-scale continuum models that are more suitable for modeling large parts, have been of interest to researchers for decades. In this work, an improved brittle damage model is presented for the simulation of dynamic fracture in continuum scale quasi-brittle metal components. Crack evolution statistics, including the number, length, and orientation of individual cracks, are extracted from high-fidelity, finite discrete element method (FDEM) simulations and used to generate effective material moduli that reflect the material’s damaged state over time. This strategy allows for the retention of small-scale physical behaviors such as crack growth and coalescence in continuum scale hydrodynamic simulations. However, the high-fidelity simulations required to generate the crack statistics are computationally expensive. Thus, steps were taken to produce a flexible constitutive model to reduce the number of costly high-fidelity simulations needed to produce accurate results. A new stress based degradation criterion is introduced for the degradation of individual material zones. This allows for the development of a heterogeneous damage distribution within the bulk material. Then a flow stress model is added to the hydrodynamic simulation to account for plasticity in quasi-brittle materials. As a result, the effective moduli model can be applied to a larger range of materials. The effective moduli constitutive model is used to simulate beryllium flyer plate experiments. The results from the continuum scale simulations using statistics from a single high-fidelity simulation are found to be in excellent agreement with numerical and experimental velocity interferometer data. The same set of crack statistics are used to extrapolate the results of a higher rate flyer plate case using the effective moduli model. In conclusion, the extension of this model to higher rate cases shows promise for further reducing the number of costly high-fidelity simulations needed to generate crack statistics.

36 MATERIALS SCIENCE↗