Search NASA⌕ Search

SEARCH · Search NASA

Results for “FREQUENCY RANGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Flight-Time Identification of a UH-60A Helicopter and Slung Load

This paper describes a flight test demonstration of a system for identification of the stability and handling qualities parameters of a helicopter-slung load configuration simultaneously with flight testing, and the results obtained. Tests were conducted with a UH-60A Black Hawk at speeds from hover to 80 kts. The principal test load was an instrumented 8 x 6 x 6 ft cargo container. The identification used frequency domain analysis in the frequency range to 2 Hz, and focussed on the longitudinal and lateral control axes since these are the axes most affected by the load pendulum modes in the frequency range of interest for handling qualities. Results were computed for stability margins, handling qualities parameters and load pendulum stability. The computations took an average of 4 minutes before clearing the aircraft to the next test point. Important reductions in handling qualities were computed in some cases, depending on control axis and load-sling combinations. A database, including load dynamics measurements, was accumulated for subsequent simulation development and validation.

Cicolani, Luigi S.↗
NASA NTRS1998

Characterization of Thin Film Microstrip Lines on Polyimide

This paper presents an in depth characterization of thin film microstrip (TFMS) lines fabricated on Dupont PI-2611 polyimide. Measured attenuation and effective dielectric constant is presented for TFMS lines with thicknesses from 2.45-7.4 microns and line widths from 5-34.4 microns over the frequency range of 1-110 GHz. The attenuation is separated into conductor and dielectric losses to determine the loss tangent of Dupont PI-2611 polyimide over the microwave frequency range. In addition, the measured characteristics are compared to closed form equations for a and eff from the literature. Based on the comparisons, recommendations for the best dosed form design equations for TFMS are made.

Ponchak, George E.↗
NASA NTRS1987

Power flow as a complement to statistical energy analysis and finite element analysis

Present methods of analysis of the structural response and the structure-borne transmission of vibrational energy use either finite element (FE) techniques or statistical energy analysis (SEA) methods. The FE methods are a very useful tool at low frequencies where the number of resonances involved in the analysis is rather small. On the other hand SEA methods can predict with acceptable accuracy the response and energy transmission between coupled structures at relatively high frequencies where the structural modal density is high and a statistical approach is the appropriate solution. In the mid-frequency range, a relatively large number of resonances exist which make finite element method too costly. On the other hand SEA methods can only predict an average level form. In this mid-frequency range a possible alternative is to use power flow techniques, where the input and flow of vibrational energy to excited and coupled structural components can be expressed in terms of input and transfer mobilities. This power flow technique can be extended from low to high frequencies and this can be integrated with established FE models at low frequencies and SEA models at high frequencies to form a verification of the method. This method of structural analysis using power flo and mobility methods, and its integration with SEA and FE analysis is applied to the case of two thin beams joined together at right angles.

Cuschieri, J. M.↗
NASA NTRS1985

An experimental and computational study of turbulent boundary layers in oscillating flows

An experimental-computational study of the behavior of turbulent boundary layers for oscillating air flows over a plane surface with a small favorable mean pressure gradient is described. Experimental data were obtained for boundary layers generated on the test section wall of a new type of facility that produces a mean flow velocity with a superposed sinusoidal component over a wide frequency range. Experimental results for unsteady velocity profiles and turbulence intensity obtained from hot wire measurements at a fixed stream-wise position on the surface are presented for frequencies ranging from 5 to 21 Hz. Numerical predictions were obtained using an unsteady boundary layer computational code and the Cebeci-Smith and Glushko turbulence models. Predicted quantities related to unsteady velocity profiles exhibit fair agreement with experiment when the Cebeci-Smith model is used.

Cook, W. J.↗
NASA NTRS1988

A low frequency radio array for space

This paper considers the need for and the possibility of constructing and operating a low-frequency array in space, the Low Frequency Space Array (LFSA), which is presently in its developmental phase, to form an entirely space-based synthesis interferometer for high-resolution high-sensitivity sky surveying and source imaging over the frequency range from about 1 to about 30 MHz. It is emphasized that there is a wealth of new astronomical information to be found in the as yet unexplored frequency range below 30 MHz, the wavelengths at which only interferometry is practicable. A possible instrumental concept for an LFSA spacecraft is described together with orbits, hardware, and subsystems.

Weiler, K. W.↗
NASA NTRS1989

Multibody modeling and verification

A summary of a ten week project on flexible multibody modeling, verification and control is presented. Emphasis was on the need for experimental verification. A literature survey was conducted for gathering information on the existence of experimental work related to flexible multibody systems. The first portion of the assigned task encompassed the modeling aspects of flexible multibodies that can undergo large angular displacements. Research in the area of modeling aspects were also surveyed, with special attention given to the component mode approach. Resulting from this is a research plan on various modeling aspects to be investigated over the next year. The relationship between the large angular displacements, boundary conditions, mode selection, and system modes is of particular interest. The other portion of the assigned task was the generation of a test plan for experimental verification of analytical and/or computer analysis techniques used for flexible multibody systems. Based on current and expected frequency ranges of flexible multibody systems to be used in space applications, an initial test article was selected and designed. A preliminary TREETOPS computer analysis was run to ensure frequency content in the low frequency range, 0.1 to 50 Hz. The initial specifications of experimental measurement and instrumentation components were also generated. Resulting from this effort is the initial multi-phase plan for a Ground Test Facility of Flexible Multibody Systems for Modeling Verification and Control. The plan focusses on the Multibody Modeling and Verification (MMV) Laboratory. General requirements of the Unobtrusive Sensor and Effector (USE) and the Robot Enhancement (RE) laboratories were considered during the laboratory development.

Wiens, Gloria J.↗
NASA NTRS1986

Monte Carlo turbulence simulation using rational approximations to von Karman spectra

Turbulence simulation is computationally much simpler using rational spectra, but turbulence falls off as f exp -5/3 in frequency ranges of interest to aircraft response and as predicted by von Karman's model. Rational approximations to von Karman spectra should satisfy three requirements: (1) the rational spectra should provide a good approximation to the von Karman spectra in the frequency range of interest; (2) for stability, the resulting rational transfer function should have all its poles in the left half-plane; and (3) at high frequencies, the rational spectra must fall off as an integer power of frequency, and since the -2 power is closest to the -5/3 power, the rational approximation should roll off as the -2 power at high frequencies. Rational approximations to von Karman spectra that satisfy these three criteria are presented, along with spectra from simulated turbulence. Agreement between the spectra of the simulated turbulence and von Karman spectra is excellent.

Campbell, C. W.↗
NASA NTRS1990

SETI prototype system for NASA's Sky Survey microwave observing project - A progress report

Two complementary search strategies, a Targeted Search and a Sky Survey, are part of NASA's SETI microwave observing project scheduled to begin in October of 1992. The current progress in the development of hardware and software elements of the JPL Sky Survey data processing system are presented. While the Targeted Search stresses sensitivity allowing the detection of either continuous or pulsed signals over the 1-3 GHz frequency range, the Sky Survey gives up sensitivity to survey the 99 percent of the sky that is not covered by the Targeted Search. The Sky Survey spans a larger frequency range from 1-10 GHz. The two searches will deploy special-purpose digital signal processing equipment designed and built to automate the observing and data processing activities. A two-million channel digital wideband spectrum analyzer and a signal processor system will serve as a prototype for the SETI Sky Survey processor. The design will permit future expansion to meet the SETI requirement that the processor concurrently search for left and right circularly polarized signals.

Klein, M. J.↗
NASA NTRS1999

Comparisons of Long-Term Schumann Resonance Records in Europe and North America

Two stations at a distance comparable with the wavelength in the Schumann resonance (SR) frequency range, one in Europe (Nagycenk, Hungary) and one in North America (West Greenwich, Rhode Island) have simultaneously monitored the natural vertical electric and horizontal magnetic field components in the frequency range of 3-25 Hz. This is a unique opportunity, as Schumann resonance stations are scarce and even fewer station have records with 5-6 year durations. The main purpose of this paper is to make comparisons in the SR time series measured simultaneously at the two field site, thereby providing access to global behavior on the seasonal and interannual time scales. The comparative measurements described here point out distinct differences in the nature of convection in South America and in Africa and reveal new aspects about the behavior of tropical continental convection on the ENSO time scale.

Satori, G.↗
NASA NTRS2003

Near-source and Remote Observations of Kilometric Continuum Radiation from Multispacecraft Observations

[I] Kilometric continuum (KC) radiation was first identified from Geotail plasma wave observations. Past authors have shown that this emission has a frequency range that overlaps that of the auroral kilometric radiation (AKR) but is characterized by a fine structure of narrow-bandwidth, linear features that have nearly constant or drifting frequency. This fine structure is distinct from that of AKR. KC also apparently has a distinct source region probably associated with the low-latitude inner magnetosphere, consistent with direction-finding and ray-tracing results. We present new high-resolution electric and magnetic field observations of KC obtained by the Polar plasma wave instrument in the near-source region. These observations show intense electrostatic and less intense electromagnetic emissions near the magnetic equator at the plasmapause. Simultaneously, Geotail, located at 20 to 30 RE in radial distance, observes KC in the same frequency range. These data support a possible mode-conversion source mechanism near a region of high-density gradient. High-resolution data obtained from wideband receivers on board both Polar and Cluster show closely spaced bands of emission near the magnetic equator that may be due to many nearby independent sources of EM emission perhaps associated with density fluctuations or cavities in the plasmasphere.

Menietti, J. D.↗
NASA NTRS2010

Use of a Microphone Phased Array to Determine Noise Sources in a Rocket Plume

A 70-element microphone phased array was used to identify noise sources in the plume of a solid rocket motor. An environment chamber was built and other precautions were taken to protect the sensitive condenser microphones from rain, thunderstorms and other environmental elements during prolonged stay in the outdoor test stand. A camera mounted at the center of the array was used to photograph the plume. In the first phase of the study the array was placed in an anechoic chamber for calibration, and validation of the indigenous Matlab(R) based beamform software. It was found that the "advanced" beamform methods, such as CLEAN-SC was partially successful in identifying speaker sources placed closer than the Rayleigh criteria. To participate in the field test all equipments were shipped to NASA Marshal Space Flight Center, where the elements of the array hardware were rebuilt around the test stand. The sensitive amplifiers and the data acquisition hardware were placed in a safe basement, and 100m long cables were used to connect the microphones, Kulites and the camera. The array chamber and the microphones were found to withstand the environmental elements as well as the shaking from the rocket plume generated noise. The beamform map was superimposed on a photo of the rocket plume to readily identify the source distribution. It was found that the plume made an exceptionally long, >30 diameter, noise source over a large frequency range. The shock pattern created spatial modulation of the noise source. Interestingly, the concrete pad of the horizontal test stand was found to be a good acoustic reflector: the beamform map showed two distinct source distributions- the plume and its reflection on the pad. The array was found to be most effective in the frequency range of 2kHz to 10kHz. As expected, the classical beamform method excessively smeared the noise sources at lower frequencies and produced excessive side-lobes at higher frequencies. The "advanced" beamform routine CLEAN-SC created a series of lumped sources which may be unphysical. We believe that the present effort is the first-ever attempt to directly measure noise source distribution in a rocket plume.

Panda, J.↗
NASA NTRS1973

An investigation of hydraulic-line resonance and its attenuation

An investigation of fluid resonance in high-pressure hydraulic lines has been made with two types of fluid dampers (or filters) installed in the line. One type involved the use of one or more closed-end tubes branching at right angles from a main line, and the other type was a fluid muffler installed in-line. These devices were evaluated in forced vibration tests with oscillatory disturbances over a 1000-Hz range applied to one end of the line and with oscillatory pressures measured at various stations along the main pipe. Limited applications of acoustic-wave theory to the branched systems are also included. Results show varying attenuations of pressure perturbations, depending on the number and location of branches and the type of muffler. Up to three branches were used in the branch-resonator study, and the largest frequency range with maximum attenuation was obtained for a three-branch configuration. The widest frequency ranges with significant attenuations were obtained with two types of fluid mufflers.

Sewall, J. L.↗
NASA NTRS1973

TRW plasma wave experiment for the IMP-H mission

The IMP-H plasma wave experiment is designed to extend knowledge of wave-particle interactions in the disturbed cislunar region, the distant geomagnetic tail, the upstream solar wind, and the flanks of the magnetosheath-shock interface. It is expected to identify plasma instabilities, study particle acceleration and heating at collisionless shocks and other discontinuities, analyze turbulent conductivity and field line merging, and provide new information on dissipation processes for suprathermal particles. Instrumentation for the plasma wave experiment is designed to measure local electric and magnetic field oscillations over the frequency range 10 Hz to 100 kHz. A 24 inch electric dipole, a 7 inch diameter air core search coil, and the associated preamplifiers are mounted on a spacecraft counterweight boom. The frequency range of 10 Hz to 100 kHz for both E and B is processed using an eight-channel spectrum analyzer located in the instrument main-body package (a standard IMP trapezoidal module, 3 inches high). Electric fields as small as 10-100 microvolts/meter and magnetic signals as small as 1-3 milligamma will be detected.

Virobik, P. F.↗
NASA NTRS1975

Analysis of proposed criteria for human response to vibration

The development of criteria for human vibration response is reviewed, including the evolution of the ISO standard 2631. The document is analyzed to show why its application to vehicle ride evaluation is strongly opposed. Alternative vertical horizontal limits for comfort are recommended in the ground vehicle ride frequency range above 1 Hz. These values are derived by correlating the absorbed power findings of Pradko and Lee with other established criteria. Special emphasis is placed on working limits in the frequency range of 1 to 10 Hz since this is the most significant area in ground vehicle ride evaluation.

Janeway, R. N.↗
NASA NTRS1984

Experimental study of noise transmission into a general aviation aircraft

The effect of add-on treatments on noise transmission into a cabin of a light aircraft was studied under laboratory conditions for diffuse and localized noise inputs. Results indicate that stiffening skin panels with honeycomb would provide on the average 3dB to 7 dB insertion loss over the most of selected frequency range H1 to 1000 Hz. Addition of damping tape on top of the honeycomb treatment increases insertion loss by 2dB to 3dB. Porous acoustic blankets show no attenuation of transmitted noise for frequencies below 300 Hz. Insertion of impervious vinyl septa between the layers of porous acoustic blankets do not provide additional noise reduction for frequencies up to about 500 Hz. Similar behavior was observed for noise barriers composed of urethane elastomer, decoupler foam and acoustic foam. A treatment composed from several layers of acoustic foams does not increase noise attenuation for the entire frequency range studied. An acoustic treatment composed of honeycomb panels, constrained layer damping tape, 2 to 3 inches of porous acoustic blankets, and limptrim which is isolated from the vibrations of the main fuselage structure seems to provide the best option for noise control.

Vaicaitis, R.↗
NASA NTRS1990

Investigation of nonlinear E.M. phenomena in the tethered magnetospheric cloud

Nonlinear effects of parametric and of heating type, produced in a plasma under the action of an electric field E(sub 0)(e exp i(omega)t), are considered in this work in connection with the Tethered Magnetospheric Cloud (TMC) accompanying the Tether Satellite System (TSS). The theoretical results show that these phenomena should appear in the ionosphere at high altitudes Z greater than or = (150-200) km, particularly, at Z approximately = 300 km of the TSS system orbit. Therefore, it is of a special interest to search these phenomena by such a unique experiment as the forthcoming first TSS-I and by the future, perhaps modified TSS missions. Because of the parametric decay instability, new branches of wave may be excited both around the electron and ion Lengmuir frequencies Omega (sub 0) = 2(pi)f(sub 0) and Omega (sub 0) = 2(pi)f(sub 0) under the influence of high frequency (HF), (f less than or = 10(exp 6) to few 10(exp 6) Hz), strong electric waves. The heating of all the kinds of particles is growing up very quickly in the ionosphere with altitude in the extra low and very low frequency ranges, F approximately = (1 to 10(exp 4) Hz, discussed below. The temperatures (energies), for example, of the electrons accelerated by the electric field become larger than the ionization potential in this frequency range already at altitudes Z greater than or = (150 - 200) km when the amplitude of the electric field is the absolute value of E(sub 0) approximately = (1-2) mV/m. The sources of these electric fields may be in the TSS-I mission, that so called Phantom Loop (PL) - the Tethered Electrodynamic Tail (TET), and the different kind of electromagnetic oscillations produced by different kinds of instabilities in the TMC plasma. The growth rates of these instabilities will become very high in the TSS surrounding magnetoplasma. However, in the future TSS missions, special artificial sources (generators) of electric fields should be used for these investigations.

Alpert, Yakov L.↗
NASA NTRS1991

Vestibular afferent responses to microrotational stimuli

Intracellular microelectrode recording/labeling techniques were used to investigate vestibular afferent responses in the bullfrog, to very small amplitude (less than 5 deg p-p) sinusoidal rotations in the vertical plane over the frequency range of 0.063-4 Hz. Robust responses to peak accelerations as low as 0.031 deg/sec per sec were obtained from units subsequently traced to either the central portion of the anterior canal crista or the striolar region of the utricle. All of these microrotationally sensitive afferent neurons had irregular resting discharge rates, and the majority had transfer ratios (relative to rotational velocity) of 1-40 spikes/sec per deg/sec. Individual utricular afferent velocity transfer ratios were nearly constant over the frequency range of 0.125-4 Hz. Canal units displayed decreasing response transfer ratios as stimulus frequencies increased. These findings indicate that, although utricular striolar and central crista afferent velocity transfer ratios to microrotations were very similar, utricular striolar afferent neurons were more faithful sensors of very small amplitude rotational velocity in the vertical plane.

Myers, Steven F.↗
NASA NTRS1990

Whistlers in Neptune's magnetosphere: Evidence of atmospheric lightning

During the Voyager 2 flyby of Neptune, a series of 16 whistler-like events were detected by the plasma wave instrument near closest approach. These events were observed at radial distances from 1.30 to 1.99 R sub N and magnetic latitudes from -7 to 33 deg. The frequencies ranged from 6.1 to 12.0 kHz, and the dispersions fit the Eckersley law for lightning-generated whistlers. Lightning in the atmosphere of Neptune is the only known source of such signals. The frequency range of the whistlers (up to 12 kHz) indicates that the local electron densities are substantially higher (N sub e greater than 30 t0 100 per cu cm) than indicated by the in situ plasma measurements. The dispersion of the whistlers is very large, typically 26,000 sec Hz(exp 0.5). Based on existing plasma density models and measurements, the dispersions are too large to be accounted for by a single direct path from the lightning source to the spacecraft. Therefore, multiple bounces from one hemisphere to the other are required. The most likely propagation path probably involves a lightning source on the dayside of the planet, with repeated bounces through the dense dayside ionosphere at low L-values.

Gurnett, D. A.↗