Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation

This is part 2 of a two part document. Part 1 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression." A team comprised of the Air Force Research Laboratory (AFRL), Boeing, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a full-span, aeroelastically scaled, wind tunnel model of a joined wing SensorCraft vehicle was mounted to a force balance to acquire a basic aerodynamic data set. In the second and third tests, the same wind tunnel model was mated to a new, two degree of freedom, beam mount. This mount allowed the full-span model to translate vertically and pitch. Trimmed flight at10 percent static margin and gust load alleviation were successfully demonstrated. The rigid body degrees of freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort. The balance and free flying wind tunnel tests will be summarized. The design of the trim and gust load alleviation control laws along with the associated results will also be discussed.

Scott, Robert C.↗
NASA NTRS2017

Ballooning for Biologists: Mission Essentials for Flying Experiments on Large NASA Balloons

Despite centuries of scientific balloon flights, only a handful of experiments have produced biologically-relevant results. Yet unlike orbital spaceflight, it is much faster and cheaper to conduct biology research with balloons, sending specimens to the near space environment of Earths stratosphere. Samples can be loaded the morning of a launch and sometimes returned to the laboratory within one day after flying. The National Aeronautics and Space Administration (NASA) flies large, unmanned scientific balloons from all over the globe, with missions ranging from hours to weeks in duration. A payload in the middle portion of the stratosphere (approx. 35 km above sea level) will be exposed to an environment similar to the surface of Mars: temperatures generally around -36 C, atmospheric pressure at a thin 1 kPa, relative humidity levels <1%, and a harsh illumination of ultraviolet (UV) and cosmic radiation levels (about 100 W/sq m and 0.1 mGy/d, respectively) that can be obtained nowhere else on the surface of the Earth, including environmental chambers and particle accelerator facilities attempting to simulate space radiation effects. Considering the operational advantages of ballooning and the fidelity of space-like stressors in the stratosphere, researchers in aerobiology, astrobiology, and space biology can benefit from balloon flight experiments as an intermediary step on the extraterrestrial continuum (ground, low Earth orbit, and deep space studies). Our presentation targets biologists with no background or experience in scientific ballooning. We will provide an overview of large balloon operations, biology topics that can be uniquely addressed in the stratosphere, and a roadmap for developing payloads to fly with NASA.

Smith, David J.↗
NASA NTRS2018

Practical Aspects of Real-Time Modeling for the Learn-To-Fly Concept

Practical aspects of autonomous onboard real-time modeling for the NASA Learn-to-Fly concept are examined using flight data from two subscale test aircraft. A practical real-time global nonlinear aerodynamic modeling method is developed and explained, along with the multiple-input excitation needed for effective real-time modeling. Critical issues for integrating real-time global nonlinear aerodynamic modeling and local linear modeling with the real-time learning adaptive control and guidance elements of the Learn-to-Fly algorithm are identified and discussed. Real-time modeling results from NASA Learn-to-Fly flight demonstrations are presented and evaluated using model fit metrics and prediction tests.

Morelli, Eugene A.↗
NASA NTRS2019

A Realistic Roadmap to Formation Flying Space Interferometry

The ultimate astronomical observatory would be a formation flying interferometer in space, immune to atmospheric turbulence and absorption, free from atmospheric and telescope thermal emission, and reconfigurable to adjust baselines according to the required angular resolution. Imagine the near/mid-infrared sensitivity of the JWST and the far-IR sensitivity of Herschel but with ALMA-level angular resolution, or imagine having the precision control to null host star light across 250m baselines and to detect molecules from the atmospheres of nearby exo-Earths. With no practical engineering limit to the formation’s size or number of telescopes in the array, formation flying interferometry will revolutionize astronomy and this White Paper makes the case that it is now time to accelerate investments in this technological area. Here we provide a brief overview of the required technologies needed to allow light to be collected and interfered using separate spacecrafts. We emphasize the emerging role of inexpensive smallSat projects and the excitement for the LISA Gravitational Wave Interferometer to push development of the required engineering building-blocks. We urge the Astro2020 Decadal Survey Committee to highlight the need for a small-scale formation flying space interferometer project to demonstrate end-to-end competency with a timeline for first stellar fringes by the end of the decade.

Gioia Rau↗
NASA NTRSDate not supplied

Flying Qualities Analysis and Piloted Simulation Testing of a Lift+Cruise Vehicle with Propulsion Failures in Hover and Low-Speed Conditions

The recent emergence of electric-Vertical Take-Off and Landing (eVTOL) vehicles for Urban Air Mobility (UAM) applications has resulted in a wide variety of configurations with unique stability and control characteristics. NASA is currently conducting research to develop conceptual design tools to accelerate public acceptance of these vehicles which includes requirements for safety during failure scenarios. This paper summarizes progress toward a toolbox for predicting flying qualities of eVTOL vehicles during critical propulsion failures that could impact the allowable design of the vehicle geometry or control system. Key topics include unique vulnerabilities of eVTOL/multirotor vehicles to propulsion failures, relevant flying qualities design metrics, and simulation modeling requirements for assessing flying qualities degradation due to failures. Results of a piloted simulation study conducted in the NASA Ames Vertical Motion Simulator (VMS) are presented. The VMS experiment was designed to assess and validate key handling qualities and safety design metrics for propulsion failures. These results show the correlation between control system design requirements and the degradation in handling qualities for various propulsion failures.

George Altamirano↗
NASA NTRS2002

Autonomous formation flying sensor for the Star Light Mission

The StarLight Mission, an element of NASA's Origins Program, was designed for first-time demonstration of two technologies: formation flying optical interferometry between spacecraft and autonomous precise formation flying of an array of spacecraft to support optical interferometry. The design overview and results of the technology effort are presented in this paper.

AFF sensor AFF formationf flying sensor autonomous↗
NASA NTRS2004

Relative Sensor with 4(pi) Coverage for Formation Flying Missions

The Terrestrial Planet Finder (TPF) pre-project, an element of NASA's Origins program, is currently developing two architectures for a mission to search for earth-like planets around nearby stars. One of the architectures being developed is the Formation Flying Interferometer (FFI). The FFI is envisioned to consist of up to seven spacecraft (as many as six 'collectors' with IR telescopes, and a 'combiner') flying in precise formation within f 1 cm of pre-determined trajectories for synchronized observations. The spacecraft-to-spacecraft separations are variable between 20 m and 100 m or more during observations to support various configurations of the interferometer in the planet-finding mode. The challenges involved with TPF autonomous operations, ranging from formation acquisition and formation maneuvering to high precision formation control during science observations, are unprecedented. In this paper we discuss the development of the formation acquisition sensor, which uses novel modulation and duplexing schemes to enable fast signal acquisition, multiple-spacecraft operation, and mitigation of inherent jamming conditions, while providing precise formation sensing and integrated radar capability. This approach performs delay synthesis and carrier cycle ambiguity resolution to improve range measurement, and uses differential carrier cycle ambiguity resolution to make precise bearing angle measurements without calibration maneuvers.

formation flying sensors↗
DOE OSTI2025

Computational screening of fly ash zeolite sorbents for boric acid removal

In the United States, many impoundments at coal-fired power plants contain elevated contaminants like arsenic, boron, barium, and selenium. Zeolites synthesized from fly ash show promise as sorbents for these contaminants. However, optimizing sorption capacity is challenging due to numerous possible topologies, silicon to aluminum (Si/Al) ratios, and cation types. In this study, molecular simulations are used to design cationic zeolites for boric acid adsorption. Force field models based on quantum mechanical calculations (PBE + D2) for Na-, Ca-, Mn-, and Fe-exchanged chabazite and LTA are presented. The new D2FF force fields reproduce DFT energies with about half the error of UFF. Zeolite performance depends on Si/Al ratio and cation type, with low Si/Al ratio chabazite (CHA) and phillipsite (PHI) zeolite frameworks exchanged with Ca 2+ or Na + /Ca 2+ mixtures showing the highest adsorption. In conclusion, these findings suggest tailored fly ash-derived zeolites could provide effective boron removal from leachate ponds.

CCR impoundment↗
DOE OSTI2021

Performance of fly ash concrete with ferronickel slag fine aggregate against alkali-silica reaction and chloride diffusion

Ferronickel slag (FNS) is an industrial by-product of ferronickel alloy production at a high temperature which can be a promising potential to be used as fine aggregate to produce more sustainable concrete. In this study, the performance of concrete containing ferronickel slag sand and fly ash relating to alkali-silica reaction (ASR) and chloride contamination was investigated. ASR-induced expansion, chloride diffusion resistance, and chloride binding capacity of FNS concrete were determined through concrete prism tests (CPT), accelerated diffusion test, and bulk diffusion test. Thermogravimetric analysis (TGA) was conducted to measure the amount of Portlandite and Friedel's salt in concrete. Concrete with 50 wt% FNS sand as fine natural aggregate replacement and 25 wt% of cement replacement by fly ash showed a remarkable potential to be used not only as a low-carbon concrete with comparable mechanical properties to conventional concrete but also with a better performance against ASR and chloride contamination.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multi-faceted framework for extrapolating early age flexural strength to facilitate rapid lifting/handling of high-volume fly ash precast members

Maintaining adequate early-age structural performance for precast concrete components has grown in importance as more sustainable mix designs become more widespread. Achieving high-early flexural strength is particularly crucial to facilitate rapid removal of hardened concrete components from formwork, often within 24 h after fresh concrete placement. Limited research has assessed the effectiveness of traditional design methods in correlating flexural strength with compressive strength for next-generation mix designs, or demonstrated extrapolation of such material performance to larger-scale structural tests. This paper presents a multi-faceted framework to reassess early-age flexural strength for concretes made with relatively high proportions of fly ash from both fresh and harvested sources. Here, the framework provides several pathways, from which the user can select based upon available resources and the specific application, to improve accuracy of early-age cracking moment calculations. Furthermore, the scope includes evaluation of strength performance under curing conditions emulative of those in a precast facility, recommending modulus of rupture equations which are more performance-driven than current design provisions, and experimental tests on prefabricated concrete beams to validate the proposed methodologies. Correlations of early-age strength with both concrete age and maturity measurements compare the effectiveness of utilizing in-situ data to further enhance the prediction methods. Ultimately, the proposed framework helped reduce errors when calculating cracking moment capacity at early ages by tailoring calculations to reflect mix-dependent behavior. Furthermore, most estimates of cracking moment were within 25 % of their corresponding experimental test results, thus promoting confidence for using these strategies with high-volume fly ash precast structures.

42 ENGINEERING↗
DOE OSTI2023

Fast On-The-Fly Monte Carlo Sampling of Temperature Dependent Thermal Scattering [Slides]

This presentation highlights the process of developing a thermal data library for MCNP6 to support on-the-fly S(alpha, beta) sampling for temperature ranges applicable to nuclear criticality safety. Advanced on-the-fly (OTF) strategy driven libraries have been developed for six materials based on ENDF/B-VIII.0. Validation of the OTF libraries is being conducted currently.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

PowerModel-AI: A First On-the-Fly Machine-Learning Predictor for AC Power Flow Solutions

The real-time creation of machine-learning models via active or on-the-fly learning has attracted considerable interest across various scientific and engineering disciplines. These algorithms enable machines to build models autonomously while remaining operational. Through a series of query strategies, the machine can evaluate whether newly encountered data fall outside the scope of the existing training set. In this study, we introduce PowerModel-AI, an end-to-end machine learning software designed to accurately predict AC power flow solutions. We present detailed justifications for our model design choices and demonstrate that selecting the right input features effectively captures load flow decoupling inherent in power flow equations. Our approach incorporates on-the-fly learning, where power flow calculations are initiated only when the machine detects a need to improve the dataset in regions where the model’s suboptimal performance is based on specific criteria. Otherwise, the existing model is used for power flow predictions. This study includes analyses of five Texas A&M synthetic power grid cases, encompassing the 14-, 30-, 37-, 200-, and 500-bus systems. The training and test datasets were generated using PowerModels.jl, an open-source power flow solver/optimizer developed at Los Alamos National Laboratory, NM, USA.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

High-Resolution Transmission Electron Microscopy Study of a Powder River Basin Coal-Derived Fly Ash

Examination of a fly ash derived from the combustion of a low-S, subbituminous Powder River Basin coal by Scanning Electron Microscopy (SEM) and High-resolution Transmission Electron Microscopy (HRTEM), both supplemented by Energy-dispersive X-ray spectroscopy (EDS), showed that the fly ashes were dominated by amorphous phases, Ca-rich plagioclase feldspars, Mg-rich phases, complex Ca-Mg-Al-Si-Ti-Fe grains, and trace amounts of REE-rich particles. Many of the particles were rimmed by a Ca-S, possibly a sulfate. HRTEM-EDS examination of a REE-rich particle proved it to be a mix of light- and heavy-rare earth minerals mixed with amorphous phases.

58 GEOSCIENCES↗
NASA NTRS2001

Optimal collision avoidance guidance for formation-flying applications

Several proposed space science missions require deployment of a number of spacecraft to form a single functional unit or a formation flying spacecraft. There are many applications of a formation flying spacecraft; variable baseline optical space interferometry is one of them.

collision avoidance path-planning formation-flying↗
NASA NTRS1999

Design of the ST 3 Formation Flying Interferometer

The interferometer will operate in both a single spacecraft mode and a formation flying mode using two spacecraft. The primary goal is to validate interferometer and formation flying technology for future missions.

ST 3 optical interferometry formation flying↗
NASA NTRS2005

A network architecture for precision formation flying using the IEEE 802.11 MAC Protocol

Precision Formation Flying missions involve the tracking and maintenance of spacecraft in a desired geometric formation. The strong coupling of spacecraft in formation flying control requires inter-spacecraft communication to exchange information. In this paper, we present a network architecture that supports PFF control, from the initial random deployment phase to the final formation. We show that a suitable MAC layer for the application protocol is IEEE's 802.11 MAC protocol. IEEE 802.11 MAC has two modes of operations: DCF and PCF. We show that DCF is suitable for the initial deployment phase while switching to PCF when the spacecraft are in formation improves jitter and throughput. We also consider the effect of routing on protocol performance and suggest when it is profitable to turn off route discovery to achieve better network performance.

precision formation flying↗
NASA NTRS2013

Fruit Fly Lab

The presentation presents the objectives goals, hardware, science, and operations for the Fruit Fly Lab technical demonstration flight. Description: To support multi-generational experiments with Drosophila melanogaster (fruit flies) at various gravity levels (0 to 2 g). The aim is also to include a video monitoring system to measure health and behavior in space.

Fruit Fly Lab↗
NASA NTRS2002

The StarLight mission: a formation-flying stellar interferometer

The StarLight mission is designed to validate the technologies of formation flying and stellar interferometry in space. The mission consists of two spacecraft in an earth-trailing orbit that formation fly over relative ranges of 40 to 600 m to an accuracy of 10 cm.

formation-flying↗