Search NASA⌕ Search

SEARCH · Search NASA

Results for “Free surface velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Computation of transonic vortex flows past delta wings Integral equation approach

The steady full-potential equation is written in the form of Poisson's equation, and the solution of the velocity field is expressed in terms of an integral equation. The solution consists of a surface integral of vorticity distribution on the wing and its free-vortex sheets and a volume integral of source distribution within a volume around the wing and its free-vortex sheets. The solution is obtained through successive iteration cycles. The source distribution is computed by using a mixed finite-difference scheme of the Murman-Cole type. The method is applied to delta wings. Numerical examples show that a conical shock is captured on the suction side of the wing. It is attached to the lower surface of the leading-edge vortex but does not necessarily reach to the wing surface.

Kandil, O. A.↗
NASA NTRS1955

An Evaluation of the Roll-Rate Stabilization System of the Sidewinder Missile at Mach Numbers from 0.9 to 2.3

A linear stability analysis and flight-test investigation has been performed on a rolleron-type roll-rate stabilization system for a canard-type missile configuration through a Mach number range from 0.9 to 2.3. This type damper provides roll damping by the action of gyro-actuated uncoupled wing-tip ailerons. A dynamic roll instability predicted by the analysis was confirmed by flight testing and was subsequently eliminated by the introduction of control-surface damping about the rolleron hinge line. The control-surface damping was provided by an orifice-type damper contained within the control surface. Steady-state rolling velocities were at all times less than 1 radian per second between the Mach numbers of 0.9 to 2.3 on the configurations tested. No adverse longitudinal effects were experienced in flight because of the tendency of the free-floating rollerons to couple into the pitching motion at the low angles of attack and disturbance levels investigated herein after the introduction of control-surface damping.

Nason, Martin L.↗
NASA NTRS1992

Heat transfer with very high free-stream turbulence. I - Experimental data. II - Analysis of results

Boundary layer heat transfer with very high freestream turbulence is investigated. The problem is studied experimentally by placing a constant-temperature heat transfer surface at various locations in the margin of a turbulent free jet and measuring both the surface heat transfer rate and the turbulence in the freestream. Freestream turbulent fluctuations 20 to 60 percent relative to the mean velocity augment heat transfer 1.8 to 4 times that which would be predicted locally using accepted correlations for turbulent boundary layers at the same Reynolds number. The correlations of Simonich and Bradshaw (1989), Pedisius et al. (1983), and Blair (1983) each fail to describe the present data. For flows over flat surfaces in air with very high freestream turbulence, greater than 0.2, u-prime determines h. A new heat transfer parameter, St-prime, characterizes turbulent boundary layer heat transfer with freestream turbulence on the domain 0-0.65 to within +/- 15 percent for high Reynolds number flows with uniform thermal boundary conditions.

Maciejewski, P. K.↗
NASA NTRS2007

PAB3D Simulations for the CAWAPI F-16XL

Numerical simulations of the flow around F-16XL are performed as a contribution to the Cranked Arrow Wing Aerodynamic Project International (CAWAPI) using the PAB3D CFD code. Two turbulence models are used in the calculations: a standard k-! model, and the Shih-Zhu-Lumley (SZL) algebraic stress model. Seven flight conditions are simulated for the flow around the F-16XL where the free stream Mach number varies from 0.242 to 0.97. The range of angles of attack varies from 0° to 20°. Computational results, surface static pressure, boundary layer velocity profiles, and skin friction are presented and compared with flight data. Numerical results are generally in good agreement with flight data, considering that only one grid resolution is utilized for the different flight conditions simulated in this study. The ASM results are closer to the flight data than the k-ε model results. The ASM predicted a stronger primary vortex, however, the origin of the vortex and footprint is approximately the same as in the k-ε predictions.

Flight Data↗
NASA NTRS1983

Influence of radiative recombination on the minority-carrier transport in direct band-gap semiconductors

When a semiconductor sample is irradiated by means of an external source, emitting photons or electrons, excess carriers are produced which distribute themselves throughout the sample. One of the parameters which determine the distribution of the carriers is the surface recombination velocity. The present investigation is concerned with the recombination lifetime tau. The predominant mechanism for recombination in wide band-gap semiconductors is described by the Shockley-Read-Hall (SRH) theory. The transport equations are derived for free carriers and the radiation field. The considered theory is applied to a semiinfinite, one-dimensional semiconductor slab irradiated by light of a given frequency. Some numerical considerations based on n-type GaAs are presented. Attention is given to a determination of the radiation transmitted through the surface of the sample.

Von Roos, O.↗
DOE OSTI2024

An implicit solution for Asay foil trajectories generated by separable, sustained-production ejecta source models

We present a simple implicit solution for the time-dependent trajectory of a thin Asay foil ejecta diagnostic for the general case where the impinging ejecta cloud is generated by a source function characterized by an arbitrary (sustained) time dependence and a time-independent (stationary) particle velocity distribution. In the limit that the source function time dependence becomes a delta function, this solution—which is amenable to rapid numerical calculations of arbitrary accuracy—exactly recovers a previously published solution for the special case of instantaneous ejecta production. We also derive simple expressions for the free-surface arrival (catch-up) time as well as the true ejecta areal mass accumulation on the accelerating foil and place bounds on the level of error incurred when applying instant-production mass solutions to a sustained-production trajectory. We demonstrate these solutions with example calculations for hypothetical source functions spanning a wide range of ejecta production durations, velocity distributions, and temporal behaviors. These calculations demonstrate how the foil trajectory is often insensitive to the temporal dependence of the source function, instead being dominated by the velocity distribution. We quantify this insensitivity using a “compatibility score” metric. Under certain conditions, one may capitalize upon this insensitivity to obtain a good approximation of the second integral of the velocity distribution from the observed foil trajectory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2018

Characterization and Analysis of Phoca Vitulina, Zalophus Californianus and Mirounga Angustirostris Vibrissae

Vibrissae of Phoca Vitulina (harbor seal) and Mirounga Angustirostris (elephant seal) possess undulations along their length. Harbor seal vibrissae have shown potential to reduce vortex induced vibrations and reduce drag compared to cylinders and ellipses. The exact geometry of the whiskers has not been well documented and the parameters that are responsible for the reduction in drag and vortex induced vibrations have not been characterized. Samples of six harbor seal vibrissae, six elephant seal vibrissae and six California sea lion (Zalophus californianus) vibrissae were collected from the Marine Mammal Center in California. The objectives of this study were to (1) Compare measurement techniques for digitizing and extracting parameters of the seal whiskers for the PeTaL (Periodic Table of Life) database. CT scanning, microscopy and 3D scanning techniques were compared. (2) Compare aerodynamic characteristics of a representative harbor seal whisker, elephant seal whisker, California sea lion whisker and ellipse at Re = 12000 and Re = 23000 based on major axis and free stream velocity. The data (in appendices) is available to compare CFD models or for further experimental validation, (3) Show close up images of whiskers and look for surface roughness effects. Variations in the seven parameters of the seal whisker were observed that may either be a feature of the vibration reduction mechanism or a result of natural variation. It is hypothesized that six parameters are sufficient to characterize seal whiskers based on analytic fitting. The drag coefficient of harbor seal whiskers examined in this study were found to be 25 percent lower than that of an ellipse with comparable major and minor axis lengths at Reynolds number of 12000. The dissipation length scale was found to be larger for seal whiskers. Potential applications of seal whisker morphology for aerospace are discussed. Roughness is not thought to play a factor in seal hydrodynamics.

Shyam, Vikram↗
NASA NTRSDate not supplied

Three-Dimensional, Multi-Phase Unsteady Flow of Water Undergoing Multiple Flow Regimes (Free Surface, Droplet, and Fluid Film)

Upgrades to the Mobile Launcher Rainbird nozzles were implemented for the Artemis II launch to increase water flow rates and improve the mobile launcher deck water coverage while minimizing the water throw distance to avoid impacting the Space Launch System (SLS) rocket nozzles. This analysis describes the use of a three-dimensional, multi-phase, free surface transient computational fluid dynamics (CFD) model to simulate the water flowing out through the Rainbird nozzle and ensure compliance with current Artemis requirements. Flow rates, pressures, velocities, nozzle throw distances and coverage areas were analyzed to ensure that system requirements are met. The completed results were used to make necessary modifications to the Ignition Overpressure Protection and Sound Suppression (IOP/SS) system Rainbird design by reshaping the nozzle used in the system.

CFD↗
NASA NTRS2005

DSMC Simulations of Ballute Aerothermodynamics Under Hypersonic Rarefied Conditions

This paper presents computational results obtained with the direct simulation Monte Carlo (DSMC) method for towed ballute applications. A ballute is an inflatable drag device that can be used to create a large amount of drag at high altitudes. Consequently, ballutes provide a potential technology for achieving aerocapture when the primary spacecraft velocity reduction (ΔV) is achieved at much higher altitudes than with the conventional rigid aeroshell. Since the ΔV is achieved at relatively high altitudes, rarefaction can be significant and is the motivation for the current study with the DSMC method. Computed surface and flow-field results are presented for a toroidal ballute, isolated tethers when exposed to free-stream flow conditions, and the flow interactions resulting from a toroidal ballute when towed by a six meter diameter Mars Pathfinder shaped (without tethers) spacecraft. All results presented are for Earth entry at velocities of 14 to 7 km/s (primary focus is at 8.55 km/s, same as some previous Titan aerocapture studies) and altitudes of 200 to 100 km. Variations of drag and heating coefficients as a function of rarefaction are presented. A description of the flow structure is provided and also an explanation of how it is affected by shock interactions produced solely by the ballute and those resulting from the two body combination of towed ballute and spacecraft is also given.

James N Moss↗
NASA NTRS1973

Vortex age as a wake turbulence scaling parameter

Research which was conducted to determine the significance of vortex age as a scaling parameter in wake turbulence development and dissipation is reported. Tests were conducted at three angles of attack, three free stream speeds, and seven downstream positions from 2 to 30 chordlengths using an NACA 0012 wing and a five hole yawhead pitot probe. The end surface of the wing tip was flat. Speeds were selected to give a predetermined range of vortex ages. The complete velocity structure of the vortex was measured at each station and speed. The resulting plots of maximum tangential velocity and vortex core diameter versus downstream distance and vortex age indicate that vortex age is not a self sufficient scaling parameter. In addition to the expected effect of lift coefficient there is also a definite free stream speed influence at high wing angles of attack. The exact cause and nature of this effect is not fully understood, but it does not appear to be explainable in terms of Mach number or Reynolds number; however, the influence of tip edge shape on spanwise flow separation appears to be an important factor.

Marshall, J. R.↗
NASA NTRS1994

Localized and distributed boundary-layer receptivity to convected unsteady wake in free stream

Receptivity to a model convected disturbance in the presence of localized and distributed variations in wall geometry and wall-suction velocity is examined. The model free-stream disturbance corresponds to the time-harmonic wake of a vibrating ribbon that is placed at a suitable distance above the surface of a thin airfoil. The advantages of using this disturbance for experiments on receptivity to convected disturbances are outlined. A brief parametric study is presented for a flat-plate boundary layer. The study quantifies the effect of wake position as well as wake width; in addition, it should be helpful in the choice of an optimal setting for a controlled experiment of the above type, which the above parametric study shows as feasible.

Choudhari, Meelan↗
NASA NTRS2009

Numerical Solutions for the CAWAPI Configuration on Structured Grids at NASA LaRC, United States

In this chapter numerical simulations of the flow around F-16XL are performed as a contribution to the Cranked Arrow Wing Aerodynamic Project International (CAWAPI) using the PAB3D CFD code. Two turbulence models are used in the calculations: a standard k-epsilon model, and the Shih-Zhu-Lumley (SZL) algebraic stress model. Seven flight conditions are simulated for the flow around the F-16XL where the free stream Mach number varies from 0.242 to 0.97. The range of angles of attack varies from 0 deg to 20 deg. Computational results, surface static pressure, boundary layer velocity profiles, and skin friction are presented and compared with flight data. Numerical results are generally in good agreement with flight data, considering that only one grid resolution is utilized for the different flight conditions simulated in this study. The Algebraic Stress Model (ASM) results are closer to the flight data than the k-epsilon model results. The ASM predicted a stronger primary vortex, however, the origin of the vortex and footprint is approximately the same as in the k-epsilon predictions.

Elmiligui, Alaa A.↗
NASA NTRS2016

An Inertial Dual-State State Estimator for Precision Planetary Landing with Hazard Detection and Avoidance

The navigation filter architecture successfully deployed on the Morpheus flight vehicle is presented. The filter was developed as a key element of the NASA Autonomous Landing and Hazard Avoidance Technology (ALHAT) project and over the course of 15 free fights was integrated into the Morpheus vehicle, operations, and flight control loop. Flight testing completed by demonstrating autonomous hazard detection and avoidance, integration of an altimeter, surface relative velocity (velocimeter) and hazard relative navigation (HRN) measurements into the onboard dual-state inertial estimator Kalman flter software, and landing within 2 meters of the vertical testbed GPS-based navigation solution at the safe landing site target. Morpheus followed a trajectory that included an ascent phase followed by a partial descent-to-landing, although the proposed filter architecture is applicable to more general planetary precision entry, descent, and landings. The main new contribution is the incorporation of a sophisticated hazard relative navigation sensor-originally intended to locate safe landing sites-into the navigation system and employed as a navigation sensor. The formulation of a dual-state inertial extended Kalman filter was designed to address the precision planetary landing problem when viewed as a rendezvous problem with an intended landing site. For the required precision navigation system that is capable of navigating along a descent-to-landing trajectory to a precise landing, the impact of attitude errors on the translational state estimation are included in a fully integrated navigation structure in which translation state estimation is combined with attitude state estimation. The map tie errors are estimated as part of the process, thereby creating a dual-state filter implementation. Also, the filter is implemented using inertial states rather than states relative to the target. External measurements include altimeter, velocimeter, star camera, terrain relative navigation sensor, and a hazard relative navigation sensor providing information regarding hazards on a map generated on-the-fly.

Bishop, Robert H.↗
NASA NTRS2020

Assessment of Transition Modeling Capability in OVERFLOW with Emphasis on Swept-Wing Configurations

In preparation for comparisons with data obtained from the recently concluded experiments in the National Transonic Facility at the NASA Langley Research Center on the new common research model with natural laminar flow (CRM-NLF), an assessment of the current transition modeling capability in the NASA OVERFLOW 2.2o code has been carried out. A combination of the available experimental data and linear stability analysis is used to evaluate the accuracy and robustness of these models for selected swept-wing type configurations, with significant crossflow. An additional goal for this work involves providing a comparative assessment of the relevant transition models in the context of a single flow solver and identifying model limitations as well as the potential for future improvements that would help strengthen the physical basis of such transition models. Included in this investigation is an assessment of the sensitivities of the underlying transition models to grid resolution (wall-normal, as well as streamwise and spanwise) and the values of extra input parameters such as the level of surface roughness and freestream turbulence variables. The flow configurations targeted in this assessment include the NASA NLF(2)-0415 swept-wing configuration, the sickle-shaped wing introduced by the Technical University of Braunschweig, and the wing-body configuration of the CRM model from the fourth and fifth AIAA CFD Drag Prediction Workshops.

Freestream velocity↗
NASA NTRS2021

Refining the Transit Timing and Photometric Analysis of TRAPPIST-1: Masses, Radii, Densities, Dynamics, and Ephemerides

We have collected transit times for the TRAPPIST-1 system with the Spitzer Space Telescope over four years. We add to these ground-based, HST, and K2 transit-time measurements, and revisit an N-body dynamical analysis of the seven-planet system using our complete set of times from which we refine the mass ratios of the planets to the star. We next carry out a photodynamical analysis of the Spitzer light curves to derive the density of the host starand the planet densities. We find that all seven planets’ densities may be described with a single rocky mass–radius relation which is depleted in iron relative to Earth, with Fe 21 wt% versus 32 wt% for Earth, and otherwise Earth-like in composition. Alternatively, the planets may have an Earth-like composition but enhanced in light elements,such as a surface water layer or a core-free structure with oxidized iron in the mantle. We measure planet masses toa precision of 3%–5%, equivalent to a radial-velocity(RV)precision of 2.5 cm s−1, or two orders of magnitude more precise than current RV capabilities. We find the eccentricities of the planets are very small, the orbits are extremely coplanar, and the system is stable on 10 Myr timescales. We find evidence of infrequent timing outliers, which we cannot explain with an eighth planet; we instead account for the outliers using a robust likelihood function. We forecast JWST timing observations and speculate on possible implications of the planet densities forthe formation, migration, and evolution of the planet system.

Eric Agol↗
NASA NTRS1997

Three Dimensional Viscous Flow Field in an Axial Flow Turbine Nozzle Passage

The objective of this investigation is experimental and computational study of three dimensional viscous flow field in the nozzle passage of an axial flow turbine stage. The nozzle passage flow field has been measured using a two sensor hot-wire probe at various axial and radial stations. In addition, two component LDV measurements at one axial station (x/c(sum m) = 0.56) were performed to measure the velocity field. Static pressure measurements and flow visualization, using a fluorescent oil technique, were also performed to obtain the location of transition and the endwall limiting streamlines. A three dimensional boundary layer code, with a simple intermittency transition model, was used to predict the viscous layers along the blade and endwall surfaces. The boundary layers on the blade surface were found to be very thin and mostly laminar, except on the suction surface downstream of 70% axial chord. Strong radial pressure gradient, especially close to the suction surface, induces strong cross flow components in the trailing edge regions of the blade. On the end-walls the boundary layers were much thicker, especially near the suction corner of the casing surface, caused by secondary flow. The secondary flow region near the suction-casing surface corner indicates the presence of the passage vortex detached from the blade surface. The corner vortex is found to be very weak. The presence of a closely spaced rotor downstream (20% of the nozzle vane chord) introduces unsteadiness in the blade passage. The measured instantaneous velocity signal was filtered using FFT square window to remove the periodic unsteadiness introduced by the downstream rotor and fans. The filtering decreased the free stream turbulence level from 2.1% to 0.9% but had no influence on the computed turbulence length scale. The computation of the three dimensional boundary layers is found to be accurate on the nozzle passage blade surfaces, away from the end-walls and the secondary flow region. On the nozzle passage endwall surfaces the presence of strong pressure gradients and secondary flow limit the validity of the boundary layer code.

Ristic, D.↗
NASA NTRS2013

The Force-Free Magnetosphere of a Rotating Black Hole

We revisit the Blandford-Znajek process and solve the fundamental equation that governs the structure of the steady-state force-free magnetosphere around a Kerr black hole. The solution depends on the distributions of the magnetic field angular velocity and the poloidal electric current. These are not arbitrary. They are determined self-consistently by requiring that magnetic field lines cross smoothly the two singular surfaces of the problem: the inner "light surface" located inside the ergosphere and the outer "light surface" which is the generalization of the pulsar light cylinder.We find the solution for the simplest possible magnetic field configuration, the split monopole, through a numerical iterative relaxation method analogous to the one that yields the structure of the steady-state axisymmetric force-free pulsar magnetosphere. We obtain the rate of electromagnetic extraction of energy and confirm the results of Blandford and Znajek and of previous time-dependent simulations. Furthermore, we discuss the physical applicability of magnetic field configurations that do not cross both "light surfaces."

Contopoulos, Ioannis↗
NASA NTRS1989

The structure of sheared turbulence near a plane boundary

The effects of shear on the structure of turbulence near a plane boundary are examined. Inhomogeneous rapid distortion theory is applied to a uniform-shear boundary layer (USBL) with a slip velocity condition at the surface. The effects of blocking the vertical component of the turbulence by the boundary in a USBL are compared with the effects in a shear-free boundary layer. It is shown that the blocking is only slightly modified by the presence of shear. The shear does alter the way in which the boundary influences the horizontal components and the turbulent shear stress near the horizontal component.

Lee, Moon Joo↗