SEARCH · Search NASA

Results for “Free surface velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Shuttle vertical fin flowfield by the direct simulation Monte Carlo method

The flow properties in a model flowfield, simulating the shuttle vertical fin, determined using the Direct Simulation Monte Carlo method. The case analyzed corresponds to an orbit height of 225 km with the freestream velocity vector orthogonal to the fin surface. Contour plots of the flowfield distributions of density, temperature, velocity and flow angle are presented. The results also include mean molecular collision frequency (which reaches 1/60 sec near the surface), collision frequency density (approaches 7 x 10 to the 18/cu m sec at the surface) and the mean free path (19 m at the surface).

Hueser, J. E.↗

NASA NTRS1986

Dual rectangular jets from a flat plate in a crossflow

Wind tunnel tests were carried out in order to study the single and dual rectangular crossflow jets injected from a flat plate perpendicular to a free stream. The length-to-width ratio of the jets was 3.97, and the spacing between the center lines was 4.7 times the width of a single jet. Surface pressure distributions were obtained for jet-to-freestream velocity ratios of 2.2 and 4, respectively. The following conclusions are offered on the basis of the experimental results: (1) the downstream extension of the negative pressures is extended to the dual jets in comparison to the single jet; (2) by increasing the jet-to-freestream velocity ratio the downstream extension of negative pressures is reduced, but negative upstream pressures become larger; (3) very high peak negative pressures occur at the front side edges of the rectangular jets compared to round jets. Velocity vector plots in the flowfield of the dual jets are given.

Kavsaoglu, M.↗

NASA NTRS1952

Axisymmetric supersonic flow in rotating impellers

General equations are developed for isentropic, frictionless, axisymmetric flow in rotating impellers with blade thickness taken into account and with blade forces eliminated in favor of the blade-surface function. It is shown that the total energy of the gas relative to the rotating coordinate system is dependent on the stream function only, and that if the flow upstream of the impeller is vortex-free, a velocity potential exists which is a function of only the radial and axial distances in the impeller. The characteristic equations for supersonic flow are developed and used to investigate flows in several configurations in order to ascertain the effect of variations of the boundary conditions on the internal flow and the work input. Conditions varied are prerotation of the gas, blade turning rate, gas velocity at the blade tips, blade thickness, and sweep of the leading edge.

Goldstein, Arthur W↗

NASA NTRS1980

A numerical investigation of thermal convection in a heat-generating fluid layer

Finite difference solutions of the equations governing thermal convection driven by uniform volumetric energy sources are presented for two-dimensional flows in a rectangular domain. The boundary conditions are a rigid (i.e, zero slip), zero heat-flux lower surface, rigid adiabatic sides, and either a rigid or free (i.e., zero shear) isothermal upper surface. Computations are carried out for Prandtl numbers from 0.05 to 20 and Rayleigh numbers from 5 x 10 to the 4th to 5 x 10 to the 8th. Nusselt numbers and average temperature profiles within the layer are in good agreement with experimental data for rigid-rigid boundaries. For rigid-free boundaries, Nusselt numbers are larger than in the former case. The structure of the flow and temperature fields in both cases is dominated by rolls, except at larger Rayleigh numbers where large-scale eddy transport occurs. Generally, low velocity upflows over broad regions of the layer are balanced by higher velocity downflows when the flow exhibits a cellular structure. The hydrodynamic constraint at the upper surface and the Prandtl number are found to influence only the detailed nature of flow and temperature fields. No truly steady velocity and temperature fields are found despite the fact that average Nusselt numbers reach steady values.

Emara, A. A.↗

NASA NTRS1982

Thermocapillary motion of bubbles inside drops

A quasi-static analysis is performed for the thermocapillary motion of a bubble located inside a drop in free fall, with arbitrary axisymmetric temperature fields prescribed on the drop surface. It is shown that in the case of an axially symmetric temperature field, the bubble moves along the axis of symmetry toward the nearest warm pole. The bubble velocity as well as the velocity and temperature fields in the drop can be predicted on the basis of the quasi-static assumptions. An approximation is presented which adequately describes bubble migration velocities in the case where the ratio of the bubble radius to the drop radius is relatively small.

Shankar, N.↗

NASA NTRS1993

Development of separation due to interaction between a shock wave and a turbulent boundary layer perturbed by rarefaction waves

The interaction of a turbulent boundary layer with rarefaction and shock waves in flows past inclined steps was investigated experimentally and theoretically. The experiments were carried out in supersonic wind tunnels with test sections of 0.6 x 0.6 m and 0.2 x 0.2 m, with adiabatic conditions on the surface model. Based on detailed measurements of pressure fields, velocity, and surface friction, combined with results of optical visualization and analysis of limiting flow lines, three characteristic flow regimes are identified. These are (1) nonseparated flow at small step angles, (2) formation of a local separation zone with a free separation point at moderate step angles, and (3) formation of a large-scale separated flow with a fixed separation point at sufficiently large step angles. The quantitative gasdynamic schemes and surface pressure distributions for these flow regimes are shown for Mach 2.85.

Zheltovodov, A. A.↗

NASA NTRS1947

Application of the Analogy Between Water Flow with a Free Surface and Two-Dimensional Compressible Gas Flow

The theory of the hydraulic analogy -- that is, the analogy between water flow with a free surface and two-dimensional compressible gas flow -- and the limitations and conditions of the analogy are discussed. A test was run using the hydraulic analogy as applied to the flow about circular cylinders of various diameters at subsonic velocities extending into the supercritical range. The apparatus and techniques used in this application are described and criticized. Reasonably satisfactory agreement of pressure distributions and flow fields existed between water and air flow about corresponding bodies. This agreement indicated the possibility of extending experimental compressibility research by new methods.

Orlin, W James↗

NASA NTRS2004

Enhanced Damping for Capillary Bridge Oscillation Using Velocity Feedback

The stability of cylindrical liquid bridges in reduced gravity is affected by ambient vibrations of the spacecraft. Such vibrations are expected to excite capillary modes of the bridge. The lowest-order unstable mode is particularly susceptible to vibration as the length of the bridge approaches the stability limit. This low-order mode is known as the (2,0) mode and is an axisymmetric varicose mode of one wavelength in the axial direction. In this work, an optical system is used to detect the (2,0)-mode amplitude. The derivative of the error signal produced by this detector is used to produce the appropriate voltages on a pair of ring electrodes which are concentric with the bridge. A mode-coupled Maxwell stress profile is thus generated in proportional to the modal velocity. Depending on the sign of the gain, the damping of the capillary oscillation can be either increased or decreased. This effect has been demonstrated in Plateau-tank experiments. Increasing the damping of the capillary modes on free liquid surfaces in space could be beneficial for containerless processing and other novel technologies. [work supported by NASA]

Wei, Wei↗

NASA NTRS2004

Enhanced Damping for Capillary Bridge Oscillation Using Velocity Feedback

Wei, Wei↗

NASA NTRS1984

Experimental analyses of trailing edge flows

An experimental study of several of the trailing edge and wake turbulence properties for a NACA 64A010 airfoil section was completed. The experiment was conducted at the Ohio State University Aeronautical and Astronautical Research Laboratory in the 6 inch X 22 inch transonic wind tunnel facility. The data were obtained at a free stream Mach number of 0.80 and a flow Reynolds number (based on chord length) of 5 million. The principle diagnostic tool was a dual-component laser Doppler velocimeter. The experimental data included surface static pressures, chordwise and vertical mean velocities, RMS turbulence intensities, local flow angles, and a determination of turbulence kinetic energy in the wake. Two angles of attack (0 and 2 degrees) were investigated. At these incidence angles, four flow field surveys were obtained ranging in position from the surface of the airfoil, between the transonic shock and the trailing edge, to the far-wake. At both angles of attack, the turbulence intensities and turbulence kinetic energy were observed to decay in the streamwise direction. In the far wake, for the non-lifting case, the turbulence intensities were nearly isotropic. For the two degree case, the horizontal component of the turbulence intensity was observed to be substantially higher than the vertical component.

Petrie, S. L.↗

NASA NTRS1986

Investigations of transonic trailing edge flows

An experimental study of several of the trailing edge and wake turbulence properties for a NACA 64A010 airfoil section was completed. The experiments were conducted at the Ohio State University Aeronautical and Astronautical Research Laboratory in the 6 inch x 22 inch transonic wind tunnel facility. The data were obtained at a free stream Mach number of 0.80 and a flow Reynolds number (based on chord length) of 5 million. The principal diagnostic tool was a dual-component laser Doppler velocimeter. The experimental data included surface static pressures, chordwise and vertical mean velocities, RMS turbulence intensities, local flow angles, and a determination of turbulence kinetic energy in the wake at chordwise locations between the transonic shock wave and the trailing edge, in the near wake just downstream of the trailing edge and in the far wake. At the two angles of attack tested (0 and 2 degrees), the turbulence intensities and turbulence kinetic energy were observed to decay in the streamwise direction. In the far wake, for the non-lifting case, the turbulence intensities were nearly isotropic. For the two degree case, the horizontal component of the turbulence intensity was observed to be substantially higher than the vertical component.

Petrie, S. L.↗

NASA NTRS1947

Application of the Analogy Between Water Flow with a Free Surface and Two-dimensional Compressible Gas Flow

The theory of hydraulic analogy, that is, the analogy between water flow with a free surface and two-dimensional compressible gas flow and the limitations and conditions of the analogy are discussed. A test run was made using the hydraulic analogy as applied to the flow about circular cylinders at various diameters at subsonic velocities extending to the super critical range. The apparatus and techniques used in this application are described and criticized. Reasonably satisfactory agreement of pressure distributions and flow fields existed between water and airflow about corresponding bodies. This agreement indicated the possibility of extending experimental compressibility research by new methods.

Orlin, W James↗

NASA NTRS2000

Measurements in a Transitional Boundary Layer Under Low-Pressure Turbine Airfoil Conditions

This report presents the results of an experimental study of transition from laminar to turbulent flow in boundary layers or in shear layers over separation zones on a convex-curved surface which simulates the suction surface of a low-pressure turbine airfoil. Flows with various free-stream turbulence intensity (FSTI) values (0.5%, 2.5% and 10%), and various Reynolds numbers (50,000, 100,000 200,000 and 300,000) are investigated. Reynold numbers in the present study are based on suction surface length and passage exit mean velocity. Flow separation followed by transition within the separated flow region is observed for the lower-Re cases at each of the FSTI levels. At the highest Reynolds numbers and at elevated FSn, transition of the attached boundary layer begins before separation, and the separation zone is small. Transition proceeds in the shear layer over the separation bubble. For both the transitional boundary layer and the transitional shear layer, mean velocity, turbulence intensity and intermittency (the fraction of the time the flow is turbulent) distributions are presented. The present data are compared to published distribution models for bypass transition, intermittency distribution through transition, transition start position, and transition length. A model developed for transition of separated flows is shown to adequately predict the location of the beginning of transition, for these cases, and a model developed for transitional boundary layer flows seems to adequately predict the path of intermittency through transition when the transition start and end are known. These results are useful for the design of low-pressure turbine stages which are known to operate under conditions replicated by these tests.

Simon, Terrence W.↗

NASA NTRS1974

A new approach to mass spectrometer measurements of thermospheric density

The gas sampling problem in satellite and high velocity probes was investigated by applying the theory of a drifting Maxwellian gas. A lens system using a free stream ion source was developed and experimentally evaluated over the pressure range of 0.00001 to 0.01 N/m sq (approx. 10 to the minus 7th power to 0.0001 torr). The source has high beam transparency, which minimizes gas-surface collisions within, or near, the ionization volume. It is shown that for high ion energy (60 eV), the extracted ion beam has an on-axis energy spread of less than 4 eV, and that 90 percent of the ions are within 2.5 deg of the beam axis. It is concluded that the molecular beam mass spectrometer concept, developed for gas density measurements in the upper atmosphere, substantially reduces gas-surface scattering and gas-surface reactions in the sample, and preserves the integrity of the gas sample during the analysis process. Studies show that both the Scout and Delta launch vehicles have adequate volume, control, velocity, and data acquisition capability necessary to obtain thermospheric number density in real time.

Melfi, L. T., Jr.↗

NASA NTRS1977

Mean velocity, turbulence intensity, and scale in a subsonic turbulent jet impinging normal to a large flat plate

To explain the increase in noise when a jet impinges on a large flat plate, mean velocity, turbulence intensity, and scale were measured at nominal nozzle-exit velocities of 61, 138, and 192 meters per second with the plate located 7.1 nozzle-exit diameters from the nozzle. The maximum turbulence intensities in free and impinging jets were about the same; however, the integral length scale near the plate surface was only about one-half the free jet scale. The measured intensities and length scales, in conjunction with a contemporary theory of aerodynamic noise, provided a good explanation for the observed increase in noise associated with the impinging jet. An increase in the volume of highly turbulent flow could be the principal reason for the increase in noise.

Boldman, D. R.↗

NASA NTRS1993

Prediction of three sigma maximum dispersed density for aerospace applications

Free molecular heating (FMH) is caused by the transfer of energy during collisions between the upper atmosphere molecules and a space vehicle. The dispersed free molecular heating on a surface is an important constraint for space vehicle thermal analyses since it can be a significant source of heating. To reduce FMH to a spacecraft, the parking orbit is often designed to a higher altitude at the expense of payload capability. Dispersed FMH is a function of both space vehicle velocity and atmospheric density, however, the space vehicle velocity variations are insignificant when compared to the atmospheric density variations. The density of the upper atmosphere molecules is a function of altitude, but also varies with other environmental factors, such as solar activity, geomagnetic activity, location, and time. A method has been developed to predict three sigma maximum dispersed density for up to 15 years into the future. This method uses a state-of-the-art atmospheric density code, MSIS 86, along with 50 years of solar data, NASA and NOAA solar activity predictions for the next 15 years, and an Aerospace Corporation correlation to account for density code inaccuracies to generate dispersed maximum density ratios denoted as 'K-factors'. The calculated K-factors can be used on a mission unique basis to calculate dispersed density, and hence dispersed free molecular heating rates. These more accurate K-factors can allow lower parking orbit altitudes, resulting in increased payload capability.

Charles, Terri L.↗

NASA NTRS1977

An experimental investigation of the trailing edge noise mechanism

An experimental investigation has been conducted to understand the physical mechanism of noise generation from a turbulent wall jet discharging over a flat plate and interacting with its sharp trailing edge. An aspect ratio 10 rectangular nozzle was used to provide the wall jet. Measurements made consist of farfield noise, surface pressure fluctuations, turbulent velocity fluctuations, and two-point space-time cross-correlations among these quantities. Results are presented which suggest strongly that the generation mechanism is the interaction of the convecting large scale quasi-orderly disturbance in the upper free shear layer of the wall jet with the trailing edge. The interaction also excites large scale strong vortical motion in the trailing edge wake. The dominant part of the sound field is highly coherent and in phase opposition across the trailing edge.

Yu, J. C.↗

NASA NTRS1978

Radiative shock dynamics. II - Hydrogen continua

The interaction between radiation and a shock wave propagating through a stellar atmosphere is investigated. Departures from local thermodynamic equilibrium (LTE) are permitted in the first two levels of a 10-level hydrogen atom; levels 3-10 are in LTE. A piston moving at constant velocity into the bottom of the atmosphere drives a shock wave. This shock produces precursor radiation that diffuses through the gas well ahead of the shock and causes a mild luminosity flash in the emergent Balmer and free-free radiation when it reaches the surface. The precursor wave deposits a large amount of radiative energy in the outer layers of the atmosphere, initiating a radiation-induced pressure wave. The process of energy transfer from the radiation field to the compression wave is similar to the Eddington valve mechanism which drives stellar pulsations. Material is accelerated outward by the radiation-induced wave; eventually it free-falls inward, hits the quasistationary atmosphere, and forms an accretion shock. The piston driven shock is weakened by radiative energy losses. When it reaches the surface, the shock is invisible in the continuum radiation.

Klein, R. I.↗