Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel performance analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Analysis of the Human Biohazard of Long-Lived Fission Products and Actinides for BREST-OD-300 Spent Fuel

The aim of this work is to perform a comparative analysis of the biohazard for the population of long-lived fission products and actinides from BREST-OD-300 reactor spent fuel taking account of the time required for different radionuclides to reach Earth’s surface by migrating from a deep disposal site. It was found that the biohazard of fission products is significantly greater than that of actinides for a long time (20000 years according to the accepted scenario of radionuclide migration). The radiological impact on the population is predicted after {sup 99}Tc – radionuclide with high migration capability – reaches the soil surface. {sup 137}Cs and {sup 90}Sr will not appreciably affect the dose load because of their relatively short half-life. In order to maintain radio-ecological balance between long-lived wastes and native uranium during the entire possible time period, it is sufficient to extract from the BREST-OD-300 spent fuel 90% of the technetium and 75% of the americium with 99.9% of the fissile materials extracted.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

FLOW TESTING AND ANALYSIS OF THE FSP-1 EXPERIMENT

The U.S. High Performance Research Reactor Conversions fuel development team is focused on developing and qualifying the uranium-molybdenum (U-Mo) alloy monolithic fuel to support conversion of domestic research reactors to low enriched uranium. Several previous irradiations have demonstrated the favorable behavior of the monolithic fuel. The Full Scale Plate 1 (FSP-1) fuel plate experiment will be irradiated in the northeast (NE) flux trap of the Advanced Test Reactor (ATR). This fueled experiment contains six aluminum-clad fuel plates consisting of monolithic U-Mo fuel meat. Flow testing experimentation and hydraulic analysis have been performed on the FSP-1 experiment to be irradiated in the ATR at the Idaho National Laboratory (INL). A flow test experiment mockup of the FSP-1 experiment was completed at Oregon State University. Results of several flow test experiments are compared with analyses. This paper reports and shows hydraulic analyses are nearly identical to the flow test results. A water velocity of 14.0 meters per second is targeted between the fuel plates. Comparisons between FSP-1 measurements and this target will be discussed. This flow rate dominates the flow characteristics of the experiment and model. Separate branch flows have minimal effect on the overall experiment. A square flow orifice was placed to control the flowrate through the experiment. Four different orifices were tested. A flow versus delta P curve for each orifice is reported herein. Fuel plates with depleted uranium in the fuel meat zone were used in one of the flow tests. This test was performed to evaluate flow test vibration with actual fuel meat densities and reported herein. Fuel plate deformation tests were also performed and reported.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Performance of U 3 Si 2 in an LWR following a cladding breach during normal operation

High-density fuels have been proposed as a possible replacement for uranium-dioxide as a fuel for light water reactors (LWRs) due to their increased loading of fissionable material. The objectives of this proposal are (1) to increase reactor cycle length and reactor power, and (2) to offset any neutronic penalty associated with advanced cladding systems. Of the high-density fuels under consideration, there is particular interest in triuranium disilicide (U 3 Si 2 ) due to its increased metal density and favorable thermal properties as compared to UO 2 . However, there are concerns regarding the chemical compatibility of U 3 Si 2 with water and steam as used for LWR coolant.This paper summarizes research on fuel-coolant chemical compatibility for UO 2 LWR fuel during a cladding breach and highlights that generally, because of its chemical inertness, UO 2 -coolant reactions are of little consequence to reactor operation. However, the volumetric expansion associated with the reaction of UO 2 and oxygen is a concern for possible conditions encountered during air ingress of dry storage. These same concerns arise for U 3 Si 2 , which exhibits greater volumetric expansion than UO 2 when exposed to water or steam. These reactions ultimately result in increased fuel volume that the cladding must accommodate, as well as additional heat generated as the fuel reacts.The BISON fuel performance code was used to perform a comparative analysis on the behavior of UO 2 and U 3 Si 2 under normal operation. Silicide fuel simulations were then extended to demonstrate how varying thermodynamic and chemical kinetics influence fuel expansion and subsequent cladding performance during a cladding breach. These simulations were further extended to a 3D subsection of a fuel rod to demonstrate the characteristics of the resulting cladding crack.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2015

PWR commercial reactor criticals as validation for spent fuel transport cask burnup credit - 14489

The burnup credit approach for a spent fuel transportation cask (SFTC) with a high density basket for 32 PWR fuel assemblies required credit not only for actinides but also for fission products, otherwise the required minimum burnups of fuel assemblies would have been too high to be practical. At the time of the development of the burnup credit methodology for this condition, no established approach existed to quantitatively validate credit for fission products. A validation approach was therefore developed specifically for this application, based on Commercial Reactor Criticals (CRCs). In this approach, hot critical state points of PWR plants were evaluated using the same codes that were used for the burnup credit evaluations for the transportation cask, namely CASMO-4 and MCNP4. A total of 36 of those state-points were analyzed, from 5 plants with two different assembly types. For each axial section of each fuel assembly, a separate CASMO-4 depletion analysis was performed, which required a total of about 4000 individual CASMO runs. The spent fuel compositions were then extracted from the CASMO runs and transferred to MCNP, where each core was modeled, considering the existing 1/8 symmetry. The core operating conditions were taken from work previously performed and documented for the Yucca Mountain project. The results of the MCNP calculations were then analyzed to establish bias and bias uncertainty values. Additional studies were performed to compare the in-core condition for the fuel with the condition that exists for the fuel in the spent fuel transport cask. The paper presents and discusses the results of the calculations, and the analysis of those results to establish bias and bias uncertainty values. The paper also presents results of the studies comparing in-core with transport cask conditions, and discusses the resulting limitations of this approach. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2017

INL/US DOE Participation in the Coordinated Research Project FUMAC: Final Report

This report summarizes the contribution of Idaho National laboratory (INL) to the IAEA Co- ordinated Research Project on Fuel Modeling under Accident Conditions FUMAC. In line with the original research agreement bewtween INL and IAEA, work at INL has focused on both (i) developments of INL’s fuel performance code BISON for the analysis of loss-of-coolant accidents (LOCA) and (ii) simulation of selected FUMAC priority cases.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Editors’ Choice—Examining Performance and Durability of Anion Exchange Membrane Fuel Cells with Novel Spirocyclic Anion Exchange Membranes

A series of spirocyclic copolymer membranes with varying ion exchange capacities (IECs) were investigated to probe the impact of polymer properties on in situ fuel cell performance and stability. In-situ electrochemical tests and post-mortem electron microscopy analysis of cross-sectioned membrane electrode assemblies (MEAs) have been combined with voltage loss breakdown analysis to evaluate the performance and degradation of different MEAs, and to probe the catalyst morphology and electrode structure at different stages of operation. Voltage loss breakdown results show that membrane degradation and kinetic losses played only a minor role in observed performance degradation and that performance losses were primarily related to increasing mass transport losses. From microscopy studies, carbon corrosion and Pt nanoparticle growth were identified at both the cathode and anode although more pronounced on the cathode resulting in significant structural changes. The membrane with the lowest IEC (1.3 mmolg −1 ) demonstrated the lowest peak power density ~ 1.16 W cm −2 , however, it showed the most stable performance (constant 0.6 A cm −2 hold) with ~ 5% degradation over 540 h. Isolation of performance losses and microscopic analysis of electrodes for anion exchange membrane fuel cells has not been reported previously, and these results help identify critical performance degradation concerns.

25 ENERGY STORAGE↗
DOE OSTI2025

STAT7 v2.0 User Guide

The STAT7 software was developed to perform steady-state, single-phase thermal hydraulics analysis of plate-fueled reactors based on statistical propagation of uncertainties. Application of the software includes non-power research and test reactor analysis, and it has been used for the conversion to low- enriched uranium fuel of U.S. High Performance Research Reactors such as the Massachusetts Institute of Technology Research Reactor. Since it can be necessary to repeat reactor safety analysis, such as during fuel reloading, STAT7 accommodates flexibility in analyzing many practical aspects of reactor fuel management. STAT7 uses a Monte Carlo approach to model uncertainty in common fuel fabrication parameters and other key reactor operating parameters required for reactor thermal hydraulics analysis. These safety calculations are ultimately intended to protect against high fuel plate temperatures due to critical heat flux, or onset of flow instability. STAT7 supports water properties based on the IAPWS-IF97 functions (The International Association for the Properties of Water and Steam Industrial Formulation 1997 for the Thermodynamic Properties of Water and Steam) in addition to fitted functions. STAT7 predicts axial profiles of fuel, cladding, and coolant temperature along a lateral stripe that runs the full length of the fuel plate from the bottom to the top. STAT7 can simultaneously analyze every axial node in each lateral stripe of all fuel plates and coolant channels in every fuel element of an entire reactor core. Power splits are calculated for each axial node of each plate to determine how much of the power goes out each face of the plate. In a single execution, STAT7 can be used to perform full core analysis by analyzing the margin to onset of nucleate boiling and onset of flow instability for each axial node of each stripe of each plate of each fuel element in the core.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2016

Tailored Microstructure and Properties in UO{sub 2}

Advanced fuels with enhanced safety margin and accident tolerance are of vital importance for safe operation of current light water reactor fleet and the development of future reactor systems. The current UO{sub 2} fuel for LWRs has low thermal conductivity, which will be further reduced upon burn-up. The intrinsically low thermal transfer efficiency of the oxide fuels results in a large temperature gradient within the fuel pellet and high center-line temperature. Thermal swelling of the pellets and fission product accommodation and retention limit the lifetime of UO{sub 2} fuel in the reactor, presenting the great challenges for extending burn-up, effective utilization of nuclear resources and minimization of nuclear waste accumulation. Critical needs also exist in developing accident tolerant fuels that can tolerate loss of coolant accident or improve fuel performance under regular operation or beyond design scenario. Key properties of advanced fuels include high thermal conductivity, oxidation resistance, high temperature mechanical properties, fission gas retention capability and thus improved accident tolerance. The US Nuclear Energy Advanced Modeling and Simulation (NEAMS) program is developing science-based next generation fuel performance modeling capability as part its Fuel Product Line in order to facilitate the predictive capability of nuclear fuel performance and assist the design and analysis of reactor systems. Critical experimental data are needed to validate MARMOT models, particularly on effective thermal transport, fracture mechanisms, grain growth kinetics and fission gas behavior. The fabrication of sintered fuel pellets with well-controlled microstructure is prerequisite to establish the correlation of the microstructure features and fuel behavior in order to develop high fidelity fuel performance models. In this talk, recent advancements on developing advanced UO{sub 2} fuels and properties improvement are overviewed with the emphasis on different accident tolerant fuel (ATF) concepts and tailoring microstructures for MARMOT validation. Current efforts on ATFs include composite fuels and high-density fuels to improve thermal-mechanical properties and fission gas retention capabilities. Different composite UO{sub 2} fuels are fabricated with heterogeneous phases as sintering additives for microstructure and property control, and the potential application of the composites as advanced fuels with enhanced accident tolerance will be discussed. In addition, recent progresses of using field-assisted sintering technologies, specifically spark plasma sintering (SPS), in tailoring and engineering fuel matrix as the target systems for validating MARMOT physics models will be highlighted. Particularly, monolithic UO{sub 2} with tailored microstructure including grain size across multiple length scales from nano-metered to micron-sizes, porosity and stoichiometry can be sintered. The impacts of tailored microstructure on thermal-mechanical properties and grain growth kinetics are discussed within the context of the MARMOT modeling. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

Fuel Cycle Modeling and Simulation of the Molten Salt Breeder Reactor

The purpose of this work is to perform a neutronic and fuel cycle analysis of the single-fluid Oak Ridge National Laboratory (ORNL) Molten Salt Breeder Reactor (MSBR) as described in ORNL-4541 [1]. Expected design requirements and system outputs were published in this referenced report; the work described herein is focused on building a model of the core, determining the best strategy for modeling the reactor core, and ultimately implementing this modeling/analysis strategy for future research in liquid fueled reactors. Similar analyses for the MSBR using unit cell and full-core models performed using MCNP [2] showed that multiregion models can accurately represent the spectral properties of the multizone MSBR [3,4].

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Microreactor Assembly Transportation Cask Model Description for Criticality Safety Validation Basis Assessment (Rev. 3)

Criticality safety analyses are completed on a transportation cask used for microreactor assembly shipment to provide an example of model and analysis to industry for reproducing this type of study on their microreactor fuel shipment. The fuel assembly considered is based on a gas-cooled microreactor (GC-MR), which utilizes HALEU fuel in the form of TRISO particles and utilizes various design options considered in industry designs. Various versions of this GC-MR assembly were studied, with and without YH 2 moderator, providing similar conclusions. The shipment cask design is revised based on an existing ES-3100 design, developed by Y-12 for the transport of highly enriched uranium (HEU), but is enlarged to hold the GC-MR fuel assembly. Criticality safety analysis for the cask/GC-MR fuel assembly package was performed using the CSAS6 sequence of SCALE6.3.2, utilizing the ENDF/B-VII.1 based continuous energy neutron library, and the analysis strictly follows the guideline from NRC reference reports. Different scenarios, e.g. normal operation, undamaged cask with water flooded, damaged cask with optimal water moderation, have been analyzed and it could be concluded the package would always have a large margin of subcriticality even packed in an infinite array. Sensitivity and similarity analyses are also performed using the TSUNAMI sequence of SCALE6.3.2, and the similarity analysis uses all the experiments from the ICSBEP Handbook with Highly Enriched Uranium (HEU), Intermediate and Mixed Enriched Uranium (IEU) and Low Enriched Uranium (LEU) systems, together with additional ones that are sponsored by the DNCSH program, and selected IRPhEP experiments using TRISO fuel and graphite moderator. These similarity analyses indicate that the dry nominal design has no similar benchmark experiments (ck values greater than 0.8), which may become problematic if more assemblies are shipped together (or a fully loaded core is shipped) and margin to criticality is reduced. However, the cask models with flooded assemblies exhibited similarities to many experiments with c k values greater than 0.8.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2010

Effects of Gas Turbine Component Performance on Engine and Rotary Wing Vehicle Size and Performance

In support of the Fundamental Aeronautics Program, Subsonic Rotary Wing Project, further gas turbine engine studies have been performed to quantify the effects of advanced gas turbine technologies on engine weight and fuel efficiency and the subsequent effects on a civilian rotary wing vehicle size and mission fuel. The Large Civil Tiltrotor (LCTR) vehicle and mission and a previous gas turbine engine study will be discussed as a starting point for this effort. Methodology used to assess effects of different compressor and turbine component performance on engine size, weight and fuel efficiency will be presented. A process to relate engine performance to overall LCTR vehicle size and fuel use will also be given. Technology assumptions and levels of performance used in this analysis for the compressor and turbine components performances will be discussed. Optimum cycles (in terms of power specific fuel consumption) will be determined with subsequent engine weight analysis. The combination of engine weight and specific fuel consumption will be used to estimate their effect on the overall LCTR vehicle size and mission fuel usage. All results will be summarized to help suggest which component performance areas have the most effect on the overall mission.

Snyder, Christopher A.↗
DOE OSTI2022

High Flux Isotope Reactor Low Enriched Uranium U-10Mo Fuel Design Parameters

Activities to convert the HFIR from HEU to LEU are ongoing as part of the US Department of Energy (DOE) National Nuclear Security Administration (NNSA) nuclear nonproliferation mission. Design activities to study the conversion of HFIR from HEU to LEU fuel explored different fuel design features and shapes with a uranium-molybdenum (U-10Mo) monolithic alloy fuel. This high-density alloy contains 90 wt % uranium and 10 wt % molybdenum and has a uranium density of 15.318gU/cm 3 . The goal of these studies is to generate several candidate HFIR LEU fuel designs of varying fuel fabrication complexity that meet the current HEU performance metrics and safety requirements. Recent advancements in modeling and simulation tools and design methods enabled a thorough analysis of the available design space with U-10Mo fuel. A surrogate model used this analysis as training data to quickly determine the performance of a design given specific design parameters. An optimization module used this surrogate model to quickly search this multidimensional search space given specific desired performance characteristics. This approach was made possible by the large available design space with U-10Mo fuel. Shift, a Monte Carlo tool optimized for high-performance computing (HPC) architectures, was used for faster calculation and better data management for reactor physics simulations. Once most of these design studies were complete, a new suite called the Python HFIR Analysis and Measurement Engine (PHAME) was developed to connect all fuel design analysis steps, making design studies more efficient and reproducible. The post-processing capabilities of these new tools are leveraged for the information provided herein. Leveraging these tools, several candidate fuel designs were selected with varying levels of feature complexity and reactor performance. This report provides design feature details for four selected HFIR LEU U-10Mo fuel designs and their corresponding performance and safety metrics. Nominal best-estimate design parameters and irradiation conditions, including fission rate densities, power densities, heat fluxes, and cumulative fission densities, are provided. Simulations show that the high uranium density of U-10Mo fuel provides a large potential design space that enables various LEU designs to meet HEU core performance metrics and safety requirements with a power increase from 85 MW (HEU) to 95 MW or 100 MW (LEU).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2015

Analysis of an existing spent fuel pool storage rack using current practices and updated depletion bias and uncertainty values - 14458

In accordance with NRC Information Notice 2011-03: Nonconservative Criticality Safety Analysis for Fuel Storage, a US nuclear power plant reviewed their analysis of record (AOR) for possible nonconservative technical specifications related to the criticality safety of fuel storage. During this review, it was determined that some legacy fuel assemblies did not meet all the assumptions of the AOR, but did meet the plant Technical Specifications. The plant entered into an Operability Evaluation in order to evaluate the moderator temperature and boron concentration assumptions used in the AOR, as well as evaluate the impact of including additional biases and depletion uncertainties for the non-borated case. As this study was part of a response to the NRC Information Notice, a full assessment was not conducted. A re-analysis of the spent fuel rack in accordance with current practices was performed. This analysis used the bounding core conditions, and included all biases and depletion uncertainties. The results challenged the 10CFR50.68(b) requirement that 'the k-effective must remain below 1.0 (subcritical), at a 95 percent probability, 95 percent confidence level, if flooded with un-borated water'. Credits for additional reactivity offsets were then analyzed. Previous assumptions for the measurement uncertainty were evaluated and subsequently reduced. New values for the depletion bias and uncertainty were applied. More detailed, realistic modeling was used to remove conservatisms. The results showed that the storage racks met the 10CFR50.68(b) criteria for the un-borated case. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

SCALE Lattice Physics Code Assessments of Accident Tolerant Fuel

This report highlights accident-tolerant fuel (ATF) code assessment activities performed under Project NRCHQ- 60-17-T-0017, Lattice Physics Enhancements and Assessment. ATF covers a broad range of advanced fuel and clad designs for light water reactors (LWRs) to enhance performance under several accident conditions. Several ATF concepts are anticipated to be deployed as lead test rods (LTRs) or lead test assemblies (LTAs) within the next five years. The purpose of this work is to assess the predictive capabilities of NRC neutronics codes that underpin various licensing calculations. ATF designs use different fuel and clad materials compared to standard UO 2 fuel and zirconium-alloy claddings (hereafter UO 2 -Zry). These new materials and geometrical designs need to be assessed to quantify the impact of nuclear data uncertainties on quantities of interest (QOIs) in licensing calculations and the impact of modeling approximations which may be valid for UO 2 -Zry but not for ATF. This report outlines a systematic approach for ATF neutronics code assessment which includes sensitivity and uncertainty (S/U) analysis of nuclear data, identification of experimental benchmark and gaps for code validation, investigation of modeling approximations, and code-to-code comparisons of calculated QOIs against high-fidelity reference continuous energy (CE) Monte Carlo (MC) calculations. This report focuses on the assessment of the SCALE/Polaris lattice physics code for reactor safety analysis. Polaris lattice physics calculations generate few group (FG) cross sections for PARCS full-core calculations. (Full-core analysis, spent fuel analysis, and severe accident analysis will be performed in future work.) The selected ATF concepts for this report include Cr 2 O 3 and Al 2 O 3 -Cr 2 O 3 -doped UO 2 fuel, U 3 Si 2 fuel, FeCrAl cladding, SiC cladding, and Cr-coated cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Application of NEAMS Multiphysics Framework for Species Tracking in Molten Salt Reactors

This report from Idaho National Laboratory (INL) summarizes the key modeling and simulation activities conducted under the Department of Energy (DOE) Molten Salt Reactor (MSR) Campaign during the Fiscal Year 2023 (FY23). The focus of the work was to leverage state-of-the-art modeling capabilities from the DOE Nuclear Energy Advanced Modeling and Simulation (NEAMS) codes to enable novel multiphysics and multiscale modeling and simulation of MSRs. Through collaboration with NEAMS code developers, advanced multiphysics analysis capabilities for MSR systems were demonstrated by coupling depletion, thermal-hydraulics, and thermochemistry into an innovative framework for chemical species transport in MSRs. As a result, the framework can track nuclides throughout their lifetimes in the core, from production (depletion) to advection throughout the salt volume (thermal-hydraulics) and off-gassing or precipitation outside of the salt (thermochemistry). This work supports the near-term deployment of MSRs by integrating the synergistic efforts between the DOE’s MSR Campaign and NEAMS program. The resulting framework will help better connect system design modelers with experimentalists to better understand and predict complex physical behaviors in MSRs. Researchers and MSR developers alike can now leverage these new modeling and simulation capabilities to perform novel analyses with applications including: • MSR dynamics during normal operational transients and accident scenarios • Off-gas system design and performance for fuel cycle and depletion analysis • Corrosion and active chemistry control for reactor component health and lifetime determination • Source term, decay heat and activity determination in accident scenarios • Special nuclear material accountancy and chemical forensic analysis for safeguards • Digital twin development of experiments and experimental reactor demonstrations • Measurement requirements for instrumentation and control design • Uncertainty and sensitivity analysis of missing data to inform future experimental data collection.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Techno-Economic Analysis of Synthetic Fuels Pathways Integrated with Light Water Reactors

The purpose of this work is to identify, model, perform techno-economic analysis, and compare two possible synfuel production routes utilizing CO 2 as the feedstock. Heat from an LWR nuclear plant is integrated wherever possible to positively affect the economics of the LWR by converting power to fuels during times of low grid electricity demand. Process and economic modeling for a conceptual synfuel production plant co-located (or in near proximity) with an LWR is presented, including the cost of CO 2 captured from an ethanol plant, compressed, and transported to the LWR hybrid plant, co-electrolysis of the CO 2 with water in a solid oxide electrolyzing cell (SOEC) system to produce syngas, and thermocatalytic conversion of the syngas to transportation fuel. The hybrid LWR/synfuels plant is assumed to be located within 50–150 miles of an ethanol plant (e.g., located in the midwest region of the United States). Performance and nth-plant economics for the co-electrolysis-based processes are evaluated and compared with biomass-gasification-based technology for the synfuel routes considered. Sensitivity analysis around the price of CO 2 and electricity, two of the major cost drivers, is presented for each case. Consideration of a carbon credit is also included in the sensitivity analysis.

10 SYNTHETIC FUELS↗
DOE OSTI2023

Effects of transient fission gas release on rod balloon burst behavior during a loss-of-coolant accident

The US nuclear energy industry is investigating strategies to increase the reactor operating cycle to 24 months, which would result in rod average burnups exceeding the current limit of 62 GWd/tU. To support this goal, multiphysics simulations tools and methodologies are being developed to predict the effects of this change during transient events such as loss-of-coolant accidents (LOCAs). In this work, two cladding burst correlations were used to predict cladding failure. Here, these were coupled with three transient fission gas release (tFGR) models and were implemented in the BISON fuel performance code to quantify any changes in cladding burst behavior during a large-break LOCA. First, a simple linear model was used to perform a sensitivity analysis of a single fuel rod. Second, a tFGR model available in BISON was applied to 281 fuel rods throughout the core. The third model examined was an empirical correlation based on data from the literature.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2004

Finite Element Analysis of MEMS Devices

A side-slide actuator and a corrugated diaphragm actuator will be analyzed and optimized this summer. Coupled electrostatic and fluid analyses will also be initiated. Both the side-slide actuator and the corrugated diaphragm actuator will be used to regulate the flow of fuel in a jet engine. Many of the side-slide actuators will be placed on top of a fuel injector that is still in the developmental stage as well. The corrugated diaphragm actuator will also be used to regulate the flow of fuel in fuel injectors. A comparative analysis of the performance matrix of both actuators will be conducted. The side-slide actuator uses the concept of mechanical advantage to regulate the flow of fuel using electrostatic forces. It is made from Nickel, Silicon Carbide, and thin layers of Oxide. The slider will have a hole in the middle that will allow fuel to pass through the hole underneath it. The goal is to regulate the flow of fuel through the inlet. This means that the actuator needs to be designed so that when a voltage is applied to the push rod, the slider will deflect in the x-direction and be able to completely block the inlet and no fuel can pass through. Different voltage levels will be tested. The parameters that are being optimized are the thickness of the diaphragm, what kind of corrugation the diaphragm should have, the length, width, and thickness of the push rod, and what design should be used to return the slider. The current possibilities for a return rod are a built in spring on the slider, a return rod that acts like a spring, or a return rod that is identical to the push rod. The final actuator design should have a push rod that has rotational motion and no translation motion, a push rod thickness that prevents warping due to the slider, and a large ratio of the displacement on the bottom of the push rod to displacement on the top of the push rod. The corrugated diaphragm actuator was optimized last winter and this summer will be spent completing the optimization of the coupled electrostatic and fluid flow parameters. It was found that Nickel is the best material to use for the diaphragm because it has a higher yield strength and allows for a larger stress, deflection and applied pressure. The parameters that were optimized were the wavelength and thickness of the diaphragm.

Corrigan, Jennifer↗