Search NASA⌕ Search

SEARCH · Search NASA

Results for “Geometric phase analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Thermal stress analysis of ceramic gas-path seal components for aircraft turbines

Stress and temperature distributions were evaluated numerically for a blade-tip seal system proposed for gas turbine applications. The seal consists of an abradable ceramic layer on metallic backing with intermediate layers between the ceramic layer and metal substrate. The most severe stresses in the seal, as far as failure is concerned, are tensile stresses at the top of the ceramic layer and shear and normal stresses at the layer interfaces. All these stresses reach their maximum values during the deceleration phase of a test engine cycle. A parametric study was carried out to evaluate the influence of various design parameters on these critical stress values. The influences of material properties and geometric parameters of the ceramic, intermediate, and backing layers were investigated. After the parametric study was completed, a seal system was designed which incorporated materials with beneficial elastic and thermal properties in each layer of the seal. An analysis of the proposed seal design shows an appreciable decrease in the magnitude of the maximum critical stresses over those obtained with earlier configurations.

Kennedy, F. E.↗

The simplicity of fractal-like flow networks for effective heat and mass transport

A variety of applications using disk-shaped fractal-like flow networks and the status of one and two-dimensional predictive models for these applications are summarized. Applications discussed include single-phase and two-phase heat sinks and heat exchangers, two-phase flow separators, desorbers, and passive micromixers. Advantages of using these fractal-like flow networks versus parallel-flow networks include lower pressure drop, lower maximum wall temperature, inlet plenum symmetry, alternate flow paths, and pressure recovery at the bifurcation. The compact nature of microscale fractal-like branching heat exchangers makes them ideal for modularity. Differences between fractal-like and constructal approaches applied to disk-shaped heat sink designs are highlighted, and the importance of including geometric constraints, including fabrication constraints, in flow network design optimization is discussed. Finally, a simple pencil and paper procedure for designing single-phase heat sinks with fractal-like flow networks based solely on geometric constraints is outlined. Benefit-to-cost ratios resulting from geometric-based designs are compared with those from flow networks determined using multivariable optimization. Results from the two network designs are within 11%. (author)

42 ENGINEERING↗

The wave energy flux of high frequency diffracting beams in complex geometrical optics

We consider the construction of asymptotic solutions of Maxwell's equations for a diffracting wave beam in the high frequency limit and address the description of the wave energy flux transported by the beam. With this aim, the complex eikonal method is applied. That is a generalization of the standard geometrical optics method in which the phase function is assumed to be complex valued, with the non-negative imaginary part accounting for the finite width of the beam cross section. In this framework, we propose an argument which simplifies significantly the analysis of the transport equation for the wave field amplitude and allows us to derive the wave energy flux. The theoretical analysis is illustrated numerically for the case of electron cyclotron beams in tokamak plasmas by using the GRAY code [D. Farina, Fusion Sci. Technol. 52, 154 (2007)], which is based upon the complex eikonal theory. The results are compared to those of the paraxial beam tracing code TORBEAM [E. Poli et al., Comput. Phys. Commun. 136, 90 (2001)], which provides an independent calculation of the energy flow.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaporation of two-dimensional black holes

We present a detailed analysis of results from a new study of the quantum evaporation of Callan-Giddings-Harvey-Strominger black holes within the mean-field approximation. This semiclassical theory incorporates backreaction. Our analytical and numerical calculations show that, while some of the assumptions underlying the standard evaporation paradigm are borne out, several are not. One of the anticipated properties we confirm is that the semiclassical space-time is asymptotically flat at right future null infinity I{sub R}{sup +} yet incomplete in the sense that null observers reach a future Cauchy horizon in finite affine time. Unexpected behavior includes that the Bondi mass traditionally used in the literature can become negative even when the area of the horizon is macroscopic; an improved Bondi mass remains positive until the end of semiclassical evaporation, yet the final value can be arbitrarily large relative to the Planck mass; and the flux of the quantum radiation at I{sub R}{sup +} is nonthermal even when the horizon area is large compared to the Planck scale. Furthermore, if the black hole is initially macroscopic, the evaporation process exhibits remarkable universal properties. Although the literature on Callan-Giddings-Harvey-Strominger black holes is quite rich, these features had escaped previous analyses, in part because of the lack of required numerical precision and in part due to misinterpretation of certain properties and symmetries of the model. Finally, our results provide support for the full quantum scenario recently developed by Ashtekar, Taveras, and Varadarajan and also offer a number of interesting problems to the mathematical relativity and geometric analysis communities.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Saturn radio emission near 1 MHz

Emission from the direction of the planet Saturn was observed by the IMP-6 spacecraft at 15 frequencies between 375 and 2200 kHz during the period April 1971 to October 1972. The Saturnian radio bursts were identified in the IMP-6 data through an analysis of the phase of the observed modulated signal detected from the spinning dipole antenna. Initial data reduction has isolated approximately 12 storms whose occurrence corresponded to times in which the spacecraft had an unobstructed view in the direction of Saturn. These events persisted over periods between one and ten minutes. Over the span of 500 days of data another 10 to 20 Saturnian events may exist, but positive identification is confused by the presence of terrestrial noise as well as a geometric ambiguity with Jupiter. A power spectral analysis of the storm occurrence times indicates a weak periodicity at 10h 30m + or - 5m at some of the observing frequencies. The spectral character of the radiation was found analogous to that of Jupiter.

Brown, L. W.↗

Cosmological constraints on f(G) dark energy models

Modified gravity theories with the Gauss-Bonnet term G = R{sup 2}−4R{sup μν}R{sub μν}+R{sup μνρσ}R{sub μνρσ} have recently gained a lot of attention as a possible explanation of dark energy. We perform a thorough phase space analysis on the so-called f(G) models, where f(G) is some general function of the Gauss-Bonnet term, and derive conditions for the cosmological viability of f(G) dark energy models. Following the f(R) case, we show that these conditions can be nicely presented as geometrical constraints on the derivatives of f(G). We find that for general f(G) models there are two kinds of stable accelerated solutions, a de Sitter solution and a phantom-like solution. They co-exist with each other and which solution the universe evolves to depends on the initial conditions. Finally, several toy models of f(G) dark energy are explored. Cosmologically viable trajectories that mimic the ΛCDM model in the radiation and matter dominated periods, but have distinctive signatures at late times, are obtained.

79 ASTRONOMY AND ASTROPHYSICS↗

Photometry and polarimetry of Jupiter at large phase angles. I - Analysis of imaging data of a prominent belt and a zone from Pioneer 10

Photopolarimetric observations of a prominent bright zone and a dark belt of Jupiter in red and blue light are analyzed which were performed by Pioneer 10 at phase angles of 12, 23, 34, 109, 120, 127, and 150 deg. Geometric and photometric reductions of the imaging data are described, the instrument sensitivity at various times is evaluated, and the data are referred to an absolute scale. The observations are analyzed in detail by comparing the data with results of radiative-transfer calculations for specific scattering models of Jupiter's atmosphere. These models include those with a vertical structure consisting of a layer of Rayleigh-scattering gas above a semiinfinite mixture of cloud particles and gas, those having a small quantity of aerosols in the gas above either the diffuse cloud in a reflecting-scattering model or the top cloud of a two-cloud-layer model, those in which a forward-scattering haze is mixed uniformly with gas, and those containing dust layers. It is found that in both the belt and the zone in red as well as blue light, cloud phase functions are required which provide both strong forward scattering and some backscattering.

Tomasko, M. G.↗

Phase Evolution and Mechanical Properties of AlCoCrFeNiSi{sub x} High-Entropy Alloys Synthesized by Mechanical Alloying and Spark Plasma Sintering

In the current investigation, AlCoCrFeNiSi{sub x} (x = 0, 0.3, 0.6 and 0.9 in atomic ratio) high-entropy alloy systems are prepared by mechanical alloying and subsequently consolidated by spark plasma sintering. The microstructural and mechanical properties were analyzed to understand the effect of Si addition in AlCoCrFeNi alloy. The x-ray diffraction analysis reveals the supersaturated solid solution of the body-centered cubic structure after 20 h of ball milling. However, the consolidation promotes the transformation of body-centered phases partially into the face-centered cubic structure and sigma phases. A recently proposed geometric model based on the atomic stress theory has been extended for the first time to classify single phase and multi-phases on the high-entropy alloys prepared by mechanical alloying and spark plasma sintering process. Improved microhardness and better wear resistance were achieved as the Si content increased from 0 to 0.9 in the present high-entropy alloy.

36 MATERIALS SCIENCE↗

Radarsat Antarctic Mapping Project: Antarctic Imaging Campaign 2

The Radarsat Antarctic Mapping Project is a collaboration between NASA and the Canadian Space Agency to map Antarctica using synthetic aperture radar (SAR). The first Antarctic Mapping Mission (AMM-1) was successfully completed in October 1997. Data from the acquisition phase of the 1997 campaign have been used to achieve the primary goal of producing the first, high-resolution SAR image map of Antarctica. The limited amount of data suitable for interferometric analysis have also been used to produce remarkably detailed maps of surface velocity for a few selected regions. Most importantly, the results from AMM-1 are now available to the general science community in the form of various resolution, radiometrically calibrated and geometrically accurate image mosaics. The second Antarctic imaging campaign occurred during the fall of 2000. Modified from AMM-1, the satellite remained in north looking mode during AMM-2 restricting coverage to regions north of about -80 degrees latitude. But AMM-2 utilized for the first time RADARSAT-1 fine beams providing an unprecedented opportunity to image many of Antarctica's fast glaciers whose extent was revealed through AMM-1 data. AMM-2 also captured extensive data suitable for interferometric analysis of the surface velocity field. This report summarizes the science goals, mission objectives, and project status through the acquisition phase and the start of the processing phase. The reports describes the efforts of team members including Alaska SAR Facility, Jet Propulsion Laboratory, Vexcel Corporation, Goddard Space Flight Center, Wallops Flight Facility, Ohio State University, Environmental Research Institute of Michigan, White Sands Facility, Canadian Space Agency Mission Planning and Operations Groups, and the Antarctic Mapping Planning Group.

Source record↗

Fast Plasma Instrument for MMS: Simulation Results

Magnetospheric Multiscale (MMS) mission will study small-scale reconnection structures and their rapid motions from closely spaced platforms using instruments capable of high angular, energy, and time resolution measurements. The Dual Electron Spectrometer (DES) of the Fast Plasma Instrument (FPI) for MMS meets these demanding requirements by acquiring the electron velocity distribution functions (VDFs) for the full sky with high-resolution angular measurements every 30 ms. This will provide unprecedented access to electron scale dynamics within the reconnection diffusion region. The DES consists of eight half-top-hat energy analyzers. Each analyzer has a 6 deg. x 11.25 deg. Full-sky coverage is achieved by electrostatically stepping the FOV of each of the eight sensors through four discrete deflection look directions. Data compression and burst memory management will provide approximately 30 minutes of high time resolution data during each orbit of the four MMS spacecraft. Each spacecraft will intelligently downlink the data sequences that contain the greatest amount of temporal structure. Here we present the results of a simulation of the DES analyzer measurements, data compression and decompression, as well as ground-based analysis using as a seed re-processed Cluster/PEACE electron measurements. The Cluster/PEACE electron measurements have been reprocessed through virtual DES analyzers with their proper geometrical, energy, and timing scale factors and re-mapped via interpolation to the DES angular and energy phase-space sampling measurements. The results of the simulated DES measurements are analyzed and the full moments of the simulated VDFs are compared with those obtained from the Cluster/PEACE spectrometer using a standard quadrature moment, a newly implemented spectral spherical harmonic method, and a singular value decomposition method. Our preliminary moment calculations show a remarkable agreement within the uncertainties of the measurements, with the results obtained by the Cluster/PEACE electron spectrometers. The data analyzed was selected because it represented a potential reconnection event as currently published.

Figueroa-Vinas, Adolfo↗

Baseline Orbit Generation for Near Rectilinear Halo Orbits

A Near Rectilinear Halo Orbit (NRHO) with an eclipse-favorable phase serves as the current baseline orbit for the Gateway mission. The baseline provides a catalog of orbit maintenance targets and serves as a reference path for other types of trajectory analysis. In this investigation, an automated multiple-shooting differential corrections strategy is developed to generate many-revolution, long-duration, ballistic baseline orbits in a higher-fidelity ephemeris force model at the eclipse-avoidant phases and at other alternative phases. Additional geometric considerations for eclipse avoidance in the NRHO are presented and utilized within a long-lead orbit maintenance-based phase shift strategy.

Emily M. Zimovan-Spreen↗

A non-linear k-{epsilon} turbulent model sensitivity analysis for flow across a PWR spacer grid with mixing vanes

In this work we studied the sensitivity of different computational fluid dynamics (CFD) numerical solutions on turbulence model, domain discretization mesh type, and inlet boundary conditions. The case under examination is a turbulent one-phase flow (water) through a scaled nuclear pressurized water reactor (PWR) fuel assembly. The main feature of this geometrical configuration is the presence of a spacer grid with mixing vanes. The design of a spacer grid with mixing vanes plays a key role for the core heat transfer efficiency, increasing the coolant heat transfer coefficient. The main reason for this is the introduction of the top mixing vanes, which consist of an ordered repetitive succession of wings that generate secondary swirling flows. The increase of heat transfer efficiency also increases the critical heat flux (CHF), making it possible to increase the design and operational limits, far from boiling crises (departure of nucleate boiling in case of a PWR). The main focus of this work was to analyze the simulation capabilities of Reynolds-averaged Navier-Stokes (RANS) models (a cubic non-linear k-epsilon model formulation) for this complex flow geometry. The CFD code used was CD-Adapco STAR-CCM+.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Two-Phase Fluid Flow Properties of Rough Fractures With Heterogeneous Wettability: Analysis With Lattice Boltzmann Simulations

Fractures are conduits for fluid flow in low-permeability geological formations. Multiphase flow properties of fractures are important in natural processes and in engineering applications such as the evaluation of the sealing capacity of caprocks and productivity of hydrocarbon-bearing tight rocks. Investigations of flow and transport through fractures typically focus on the effects of fracture geometric and mechanical factors such as aperture, roughness, and compressibility. The wettability of the fracture surfaces and its influence on microscale interfacial phenomena and macroscale effective transport properties are seldom studied. In this study, we investigated the effect of heterogeneous wetting properties on the displacement of water by supercritical CO2 through a series of lattice Boltzmann method simulations. The results show the evolution of the CO2 plume within a fracture is controlled by both the roughness of the aperture field and the wetting distribution. We combined these factors into a capillary pressure map that can be related to the macroscopic flow behavior of the fracture. We observed that heterogeneous wetting distributions promote the residual trapping of water where lower capillary pressures allowed for isolated water pockets in higher capillary pressure zones. Analysis of fracture unsteady relative permeability shows the effect of wetting on permeability evolution and provides support for the viscous-coupling relative permeability model. Finally, analysis of the steady-state relative permeability and saturation demonstrates a strong correlation between permeability and the standard deviation of the capillary pressure field. Thus, characterizing the distribution of wetting properties of fractures is crucial to understanding multiphase fracture flow and transport properties.

58 GEOSCIENCES↗

Semiclassical analysis of the Wigner 9j symbol with small and large angular momenta

We derive an asymptotic formula for the Wigner 9j symbol, in the limit of one small and eight large angular momenta, using a gauge-invariant factorization for the asymptotic solution of a set of coupled wave equations. Our factorization eliminates the geometric phases completely, using gauge-invariant noncanonical coordinates, parallel transports of spinors, and quantum rotation matrices. Our derivation generalizes to higher 3nj symbols. We display without proof some asymptotic formulas for the 12j symbol and the 15j symbol in the Appendices. This work contributes an asymptotic formula of the Wigner 9j symbol to the quantum theory of angular momentum and serves as an example of a general method for deriving asymptotic formulas for 3nj symbols.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Enhancing Adhesion: Relative Merits of Different Approaches

Adhesive performance is improved mainly by manipulation of the bimaterials interface zone, which is only a few molecules thick. There are three approaches to enhancement of interfacial adhesion at the molecular level. They are 1) changing the nonchemically bonded interactions across the interface from weak ones to strong ones, 2) making the true interfacial area much larger than the simple geometric area, and 3) inducing chemical bonding between the two materials forming the interface. Our goal this summer was to question some of the built-in assumptions contained within these approaches and to determine the most promising approach, both theoretically and practically, for enhancing adhesion in NASA structures. Our computations revealed that all three of these approaches have, in theory, the potential to enhance molecular adhesion approximately ten-fold. Experiments, however, revealed that this excellent level of enhancement is not likely to be reached in practice. Each approach was found to be severely limited by practical problems. In addition, some of the built-in assumptions associated with these approaches were found to be insufficient or inadequate. The first approach, changing the nonchemically bonded interactions from weak to strong, Is an example of one containing inadequate assumptions. The extensive literature on intermolecular interactions, based on solution studies, shows that certain functional group pairs interact much more strongly than others. It has always been assumed that these data can be reliably extended to systems where only one member of the pair is in solution and the other Is contained in a solid surface. Our experiments this summer demonstrated that solution data do not adequately predict the strength of functional group interaction at the solid-liquid interface. Furthermore, the strong solvents needed to dissolve the monomers or polymers to which the functional groups of interest are attached compete successfully with the solid surface for the functional group. As a result, functional groups in solution cannot pair with the complementary groups in the solid surface, and the expected enhancement of nonchemically bonded interactions is not realized. The second approach, increasing the true interfacial area, is an example of one containing inadequate assumptions and suffering from numerous practical problems. First, practitioners have assumed that material removal, such as bead blasting or etching, increases true surface area (and therefore interfacial area) in a meaningful way. Our geometric analysis demonstrated that removal methods increase area by a factor of two at most. To increase interfacial area by an order of magnitude or more. a thin layer of high porosity must be added to the substrate surface prior to application of the adhesive phase. Consistent with this finding, we attempted to create a thin layer of rigid, highly porous glass on the surface of our smooth glass substrate by means of sol-gel technology. We were unable to surmount a wide variety of practical problems and obtained only collapsed, nonporous layers. Thus this approach, appealing in principle, would require long term development and is not promising in the near term. The third approach, inducing chemical bonding at the interface, is an example of one having neither inadequate assumptions nor insurmountable practical problems. When silicate glass is the substrate, there are only a few chemical reactions that can be successfully conducted to create these chemical bonds, and these reactions usually involve silicon-containing reagents. We compared the silazane reagents to the silane reagents and found through experiment that the silazanes react with the glass surface much more readily, and under milder conditions, than the silanes. The functional groups attached to the glass surface by silazane reactions were not able to be removed by solvent extraction, elevated temperature exposure, or mechanical action. This clearly indicates that the formation of chemical bonds at the interface is the most effective approach for enhancing molecular adhesion.

Penn, L. S.↗

Modeling and Analysis of Stirling Power Convertors

Modeling and Analysis of Stirling Power Convertors Luis A. Rodriguez1 Steven M. Geng, Terry V. Reid, Scott D. Wilson NASA Glenn Research Center, Cleveland, OH, 44135, USA NASA Glenn’s Thermal Energy Conversion Branch is supporting the development of the next generation free-piston Stirling power convertors. American Superconductor (AMSC) and Sunpower Inc. are the two firms under contract to develop the Flexure Isotope Stirling Convertor (FISC) and the Sunpower Robust Stirling Convertor (SRSC), respectively. To comprehend and forecast convertor performance, Sage, ANSYS® Maxwell, and ANSYS® Fluent were used to model the Stirling thermodynamic cycle, alternator electromagnetics, and piston and displacer dynamics. I. Introduction Stirling convertors are being developed by NASA as a potential steady source of electrical power for NASA’s future scientific space missions. Currently, NASA Glenn Research Center has two corporations under contract, American Superconductor (AMSC) and Sunpower Inc., for the development of the next generation of free-piston Stirling convertors for dynamic radioisotope power systems. AMSC is developing the Flexure Isotope Stirling Convertor (FISC), which uses flexures to prevent side motion and rubbing of the piston. Similarly, Sunpower Inc, is developing the Sunpower Robust Stirling Convertor (SRSC). The SRSC uses gas bearings to prevent radial contact of the moving piston. As convertor development continues, it is increasingly important to understand and predict the interactions of components in the system, how they respond to one another, and how they perform as a response to changes in operating conditions. A suitable and enlightening way to demonstrate and foresee these interactions is with the use of accurate modeling software. Sage, ANSYS® Maxwell, and ANSYS® Fluent are the current modeling tools used by NASA to analytically determine convertor performance. Sage is a one-dimensional object-oriented commercial software package used for modeling and optimizing Stirling convertors for Dynamic Radioisotope Power Systems (DRPS) and it is one of the most accurate Stirling convertor codes in use by NASA. This code is the successor to GLIMPS (Globally-Implicit Stirling Cycle Simulation) and GLOP (GLIMPS Optimization) software created by Gedeon Associates [1]. Model input parameters are typically material/gas type, component physical dimensions, temperatures, frequency, charge pressure, and number of time/space nodes. Sage is used to model both the FISC’s and SRSC’s Stirling cycle thermodynamics and piston/displacer dynamics. Performance maps were created and analyzed for both power systems to better understand the relationship between the following conditions: cold-end temperature, hot-end temperature, piston/displacer amplitudes, pressure drop, and thermal input power. The synergy between these conditions will help determine parameter sensitivity. ANSYS® Maxwell was used to create a three-dimensional (3-D) axisymmetric model for both FISC and SRSC alternators. The significant physical components included in each model are the magnets, magnet carrier, outer/inner laminations, and the coil. Inputs to the model are piston amplitude, piston frequency, alternator load, coil resistance, tuning capacitance, and specific material properties. The alternator models calculate terminal voltage, current, piston/current phase, voltage/current phase, coil inductance, terminal power and efficiency. The RI2 losses, core (hysteresis and eddy) losses, and magnet/can eddy losses are also a part of the final results. ANSYS® Fluent is used to build 3-D computational fluid dynamic (CFD) models to examine the Stirling cycle thermodynamics for both the FISC and SRSC systems. Three-dimensional Computer Aided Design (CAD) models were used to create the physical components of each convertor. Steady-state simulations were conducted for hardware testing, prediction of environmental losses during testing, and generation of radiation look-up tables. The model inputs to the aforementioned analysis are the material properties and boundary thermal conditions. The steady-state model calculates temperature and heat flow distributions. Transient 3-D calculations were also part of the CFD analysis. In this study a physically reduced version of the FISC is used to obtain a prediction of available engine power. For the gas bearing SRSC, the transient effort is used to obtain a prediction of bearing pad performance and its sensitivity to micro-channel geometric variation. The model inputs to the transient simulations are the piston amplitude, displacer amplitude, frequency, displacer/piston phase angle, dynamic deforming CFD grid, temperature boundary conditions, and user defined files describing motion profile of piston/displacer. The results of the model are temperature distributions, heat distributions, and PV power produced at pre-determined conditions.

Luis A Rodriguez↗

Microstructure and particulate properties of the surfaces of Io and Ganymede - Comparison with other solar system bodies

The phase curves of Io and Ganymede between 0 and 40 deg solar phase angle have been compiled from Voyager photopolarimeter and ground-based observations. Modeling the data with the Lumme-Bowell theory made it possible to determine improved estimates of the surface texture and particulate properties. Accurate V-band zero-phase geometric albedos, phase integrals, and Bond albedos are also obtained. The properties of the particles on Io's surface appear to be different from those of other solar system objects whose surfaces are totally controlled by impact cratering processes. Sulfur and SO2 frost, previously identified by spectral analysis, seem to exist in a physical form not commonly found on earth. The agglomeration of volcanic ash into aggregates on Io's surface is postulated.

Pang, K. D.↗

A New and General Formulation of the Parametric HFGMC Micromechanical Method for Three-Dimensional Multi-Phase Composites

The recent two-dimensional (2-D) parametric formulation of the high fidelity generalized method of cells (HFGMC) reported by the authors is generalized for the micromechanical analysis of three-dimensional (3-D) multiphase composites with periodic microstructure. Arbitrary hexahedral subcell geometry is developed to discretize a triply periodic repeating unit-cell (RUC). Linear parametric-geometric mapping is employed to transform the arbitrary hexahedral subcell shapes from the physical space to an auxiliary orthogonal shape, where a complete quadratic displacement expansion is performed. Previously in the 2-D case, additional three equations are needed in the form of average moments of equilibrium as a result of the inclusion of the bilinear terms. However, the present 3-D parametric HFGMC formulation eliminates the need for such additional equations. This is achieved by expressing the coefficients of the full quadratic polynomial expansion of the subcell in terms of the side or face average-displacement vectors. The 2-D parametric and orthogonal HFGMC are special cases of the present 3-D formulation. The continuity of displacements and tractions, as well as the equilibrium equations, are imposed in the average (integral) sense as in the original HFGMC formulation. Each of the six sides (faces) of a subcell has an independent average displacement micro-variable vector which forms an energy-conjugate pair with the transformed average-traction vector. This allows generating symmetric stiffness matrices along with internal resisting vectors for the subcells which enhances the computational efficiency. The established new parametric 3-D HFGMC equations are formulated and solution implementations are addressed. Several applications for triply periodic 3-D composites are presented to demonstrate the general capability and varsity of the present parametric HFGMC method for refined micromechanical analysis by generating the spatial distributions of local stress fields. These applications include triply periodic composites with inclusions in the form of a cavity, spherical inclusion, ellipsoidal inclusion, discontinuous aligned short fiber. A 3-D repeating unit-cell for foam material composite is simulated.

Haj-Ali, Rami↗