Raman spectrum of calcium carbonate at high pressures
Calcite and aragonite high pressure Raman line spectra comparisons, testing structural identification theory
Fong, M. Y.↗
SEARCH · Search NASA
Results for “High Pressure”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Impact sensitivity of materials in contact with liquid and gaseous oxygen at high pressure
Tests run at high pressure indicate that various polymer materials used show inverse relationship between thickness and impact sensitivity. Several materials tested exhibited greater impact sensitivity in gaseous oxygen than in liquid oxygen. Materials tested in gaseous oxygen showed enhanced impact sensitivity with higher pressure.
Schwinghamer, R. J.↗
A generalized theory for eccentric and misalignment effects in high-pressure annular seals
High-pressure annular seal leakage and dynamic coefficients vary with eccentricity and misalignment. Recent seal leakage data with both concentric and fully eccentric alignments support the seal leakage model with surface roughness and eccentricity effects included. In this paper, the seal dynamic coefficient calculation has been generalized and allows direct calculation of the seal dynamic coefficients at any circumferential location. The generalized solution agrees with the results obtained by using the calculated values of an earlier paper and performing a coordinate transformation. The analysis results coincide with the measured data in showing that the stiffness and damping matrices of seal coefficients are not skew symmetric, and the main diagonal seal coefficients are not equal. The measured direct stiffnesses were found higher than predicted by the concentric seal theory, but this may be explained by the presence of eccentricity in the test operating mode.
Chen, W. C.↗
A microstructural signature of the coesite-quartz transformation: New insights from high-pressure experiments and EBSD
Ultra-high pressure (UHP) metamorphism is difficult to identify in continental crust as few petrological barometers are suitable for dominantly felsic lithologies. In such cases, burial to extreme depths is commonly identified through the preservation of coesite, a high-pressure polymorph of SiO 2 that typically forms at depths exceeding ∼ 100 km (i.e., > 2 GPa pressure). Unfortunately, coesite readily transforms to quartz upon exhumation, meaning that UHP terranes may often be overlooked. While some studies have suggested that quartz may inherit an orientation signature indicative of former coesite, both the specific nature of this signature and the conditions favouring its development remain uncertain. Here, to address this problem, we combine electron backscatter diffraction analysis of natural and experimental samples to explore microstructural evolution across the coesite-quartz phase transformation. We demonstrate that neighbouring domains of quartz commonly feature an 84 ± 4° rotation of [c] axes around the pole of a common {m} plane. This orientation relationship is a product of epitaxy, whereby the {$11\bar{2}2$} Japan twin plane in quartz nucleates on the (010) plane in coesite. In supercell simulations, the nucleation of Japan twins can be explained by the energetically favourable alignment of quartz tetrahedra on parental coesite tetrahedra. Through experiments, we demonstrate that this signature emerges over a broad range of conditions, regardless of the availability of nucleation sites (e.g., grain boundaries) or the density of crystal lattice defects (e.g., dislocations). Overall, our work provides a quantitative and unambiguous tool for identifying UHP terranes from quartz in isolation.
Coesite↗
Reusable High-Pressure Connector
Fluid line connector for high pressure tests has split ferrule, nut, and O-ring seal. Following test, ferrule nut, and O-ring fitting are removed leaving line unaltered except for bushing braze to free end. Connector assures strong joint for high-pressure testing without redundant parts requiring postest debrazing.
Jensen, H. O. C.↗
Performance of multimirror quartzline lamps in a high-pressure, underwater environment
Multimirror Quartzline Lamps are extremely versatile and effective for nonconventional imaging requirements such as high-speed photo and video instrumentation and high-magnification imaging. The lamps' versatility though, is not limited to conventional environments. Many research experiments and projects require a high pressure environment. Continuous photographic data acquisition in a high-pressure vessel requires wall penetrations and creates design problems as well as potential failure sites. Underwater photography adds the extra consideration of a liquid. This report expands upon the basic research presented in, Performance of Multimirror Quartzline Lamps in High-Pressure Environments, (NASA-TM-83793, Ernie Walker and Howard Slater, 1984). The report provides information to professional industrial, scientific, and technical photographers as well as research personnel on the survivability of lighting a multimirror quartzline lamp in a nonconventional high-pressure underwater environment. Test results of lighted ELH 300 W multimirror quartzline lamps under high-pressure conditions are documented and general information on the lamps' intensity (footcandle output), cone of light coverage, approximate color temperature is provided. Continuous lighting considerations in liquids are also discussed.
Slater, Howard A.↗
Depth Gauge for Liquids Under High Pressure
Piezoelectric element mounted in hole drilled in high-pressure plug. Transducer used to measure depth of liquid when pressure in vessel high. New configuration transmits ultrasonic vibration directly into liquid, enhancing signal strength, accuracy, and range, yet piezoelectric element protected from high-pressure liquid.
Zuckerwar, A. J.↗
NASA mechanical impact testing in high-pressure oxygen
Three independently developed high-pressure gaseous oxygen mechanical impact testers have been used to evaluate materials for the Space Shuttle Program. A test program evaluating the performance of these test systems is described. The gaseous and liquid oxygen test procedures and equipment are considered along with the material selection procedures. The results of the NASA mechanical impact tester variability study are presented, including penetration function curves and curve parameters and equivalent energies and comparisons of high-pressure testers at ambient pressure and temperature, ambient temperature and 34 MPa, and cryogenic temperature and 34 MPa. Finally, a summary of NASA mechanical impact test data is presented.
Bryan, C. J.↗
High pressure water jet cutting and stripping
High pressure water cutting techniques have a wide range of applications to the American space effort. Hydroblasting techniques are commonly used during the refurbishment of the reusable solid rocket motors. The process can be controlled to strip a thermal protective ablator without incurring any damage to the painted surface underneath by using a variation of possible parameters. Hydroblasting is a technique which is easily automated. Automation removes personnel from the hostile environment of the high pressure water. Computer controlled robots can perform the same task in a fraction of the time that would be required by manual operation.
Hoppe, David T.↗
High-Pressure Oxygen Dryer (HPOD) FY 2023 Trade Study and Market Survey
A reliable source of dry, high-pressure oxygen is needed for future lunar missions to support nominal and contingency operations on the Surface Habitat (SH) and the Pressurized Rover (PR) in future Gateway missions. A High-Pressure Oxygen Dryer (HPOD) is needed to support potential use of primary oxygen generation systems, the High-Pressure Oxygen Generation Assembly (HPOGA) and the Skyre EOC, by drying the wet oxygen exiting the systems. The objective of this paper is to perform an architecture trade study and market survey of options to dry a continuous stream of 45°C, 4000 PSIG oxygen containing ~ 500 ppm H2O (dew point 52°C) down to < 7 ppm H2O (dew point -15°C) for both the 28-day and 365-day timeframe. A total of seven different technologies were identified as potential dryer candidates during the market survey, relying on one of three principles, adsorption, filtration, and cooling. During the sizing and trade study, it was found that several of the technologies aren’t sufficient for the extreme conditions and were eliminated. In the end, a single-use throw away adsorption bed traded the best for single mission use, while a pressure regenerative adsorption bed traded the best for a multiple mission scenario. The results of this analysis are intended to influence future design work for high-pressure oxygen drying applications.
High Pressure Oxygen↗
High-Pressure Oxygen Dryer (HPOD) FY 2023 Trade Study and Market Survey
A reliable source of dry, high-pressure oxygen is needed for future lunar missions to support nominal and contingency operations on the Surface Habitat (SH) and the Pressurized Rover (PR) in future Gateway missions. A High-Pressure Oxygen Dryer (HPOD) is needed to support potential use of primary oxygen generation systems, the High-Pressure Oxygen Generation Assembly (HPOGA) and the Skyre EOC, by drying the wet oxygen exiting the systems. The objective of this paper is to perform an architecture trade study and market survey of options to dry a continuous stream of 45°C, 4000 PSIG oxygen containing ~ 500 ppm H 2 O (dew point 52°C) down to < 7 ppm H 2 O (dew point -15°C) for both the 28-day and 365-day timeframe. A total of seven different technologies were identified as potential dryer candidates during the market survey, relying on one of three principles, adsorption, filtration, and cooling. During the sizing and trade study, it was found that several of the technologies aren’t sufficient for the extreme conditions and were eliminated. In the end, a single-use throw away adsorption bed traded the best for single mission use, while a pressure regenerative adsorption bed traded the best for a multiple mission scenario. The results of this analysis are intended to influence future design work for high-pressure oxygen drying applications.
High Pressure Oxygen↗
High-Pressure Oxygen Dryer (HPOD) FY 2023 Trade Study and Market Survey
A reliable source of dry, high-pressure oxygen is needed for future lunar missions to support nominal and contingency operations on the Surface Habitat (SH) and the Pressurized Rover (PR) in future Gateway missions. A High-Pressure Oxygen Dryer (HPOD) is needed to support potential use of primary oxygen generation systems, the High-Pressure Oxygen Generation Assembly (HPOGA) and the Skyre EOC, by drying the wet oxygen exiting the systems. The objective of this paper is to perform an architecture trade study and market survey of options to dry a continuous stream of 45°C, 4000 PSIG oxygen containing ~ 500 ppm H2O (dew point 52°C) down to < 7 ppm H2O (dew point -15°C) for both the 28-day and 365-day timeframe. A total of seven different technologies were identified as potential dryer candidates during the market survey, relying on one of three principles, adsorption, filtration, and cooling. During the sizing and trade study, it was found that several of the technologies aren’t sufficient for the extreme conditions and were eliminated. In the end, a single-use throw away adsorption bed traded the best for single mission use, while a pressure regenerative adsorption bed traded the best for a multiple mission scenario. The results of this analysis are intended to influence future design work for high-pressure oxygen drying applications.
High Pressure Oxygen↗
Subdiffusive High-Pressure Hydrogen Gas Dynamics in Elastomers
We report elastomeric rubber materials serve a vital role as sealing materials in the hydrogen storage and transport infrastructure. With applications including O-rings and hose liners, these components are exposed to pressurized hydrogen at a range of temperatures, cycling rates, and pressure extremes. High-pressure exposure and subsequent rapid decompression often lead to cavitation and stress-induced damage of the elastomer due to localization of the hydrogen gas. Here, we use all-atom classical molecular dynamics simulations to assess the impact of compositional variations on gas diffusion within the commonly used elastomer ethylene–propylene–diene monomer (EPDM). With the aim to build a predictive understanding of precursors to cavitation and to motivate material formulations that are less sensitive to hydrogen-induced failure, we perform systematic simulations of gas dynamics in EPDM as a function of temperature, gas concentration, and cross-link density. Our simulations reveal anomalous, subdiffusive hydrogen motion at pressure and intermediate times. We identify two groups of gas with different mobilities: one group exhibiting high mobility and one group exhibiting low mobility due to their motion being impeded by the polymer. With decreasing temperatures, the low-mobility group shows increased gas localization, the necessary precursor for cavitation damage in these materials. At lower temperatures, increasing cross-link density led to greater hydrogen gas mobility and a lower fraction of caged hydrogen, indicating that increasing cross-link density may reduce precursors to cavitation. Finally, we use a two-state kinetic model to determine the energetics associated with transitions between these two mobility states.
36 MATERIALS SCIENCE↗
A Preliminary Study on the Toxic Combustion Products Testing of Polymers Used in High-Pressure Oxygen Systems
One likely cause of polymer ignition in a high-pressure oxygen system is adiabatic-compression heating of polymers caused by pneumatic impact. Oxidative _ pyrolysis or combustion of polymers in a high-pressure oxygen system could generate toxic gases. This paper reports the preliminary results of toxic combustion product testing of selected polymers in a pneumatic-impact test system. Five polymers commonly used in high-pressure oxygen systems, Nylon 6/6, polychlorotrifluoroethylene (CTFE), polytetrafluoroethylene (PTFE), fluoroelastomer (Viton(TradeMark) A), and nitrile rubber (Buna N), were tested in a pneumatic-impact test system at 2500- or 3500-psia oxygen pressure. The polymers were ignited and burned, then combustion products were collected in a stainless-steel sample bottle and analyzed by GC/MS/IRD, GC/FID, and GC/Methanizer/FID. The results of adiabatic-compression tests show that combustion of hydrocarbon polymers, nitrogen-containing polymers, and halogenated polymers in high-pressure oxygen systems are relatively complete. Toxicity of the combustion product gas is presumably much lower than the combustion product gas generated from ambient-pressure oxygen (or air) environments. The NASA-Lewis equilibrium code was used to determine the composition of combustion product gas generated from a simulated, adiabatic-compression test of nine polymers. The results are presented and discussed.
Hshieh, Fu-Yu↗
Constitutive and damage material modeling in a high pressure hydrogen environment
Numerous components in reusable space propulsion systems such as the SSME are exposed to high pressure gaseous hydrogen environments. Flow areas and passages in the fuel turbopump, fuel and oxidizer preburners, main combustion chamber, and injector assembly contain high pressure hydrogen either high in purity or as hydrogen rich steam. Accurate constitutive and damage material models applicable to high pressure hydrogen environments are therefore needed for engine design and analysis. Existing constitutive and cyclic crack initiation models were evaluated only for conditions of oxidizing environments. The main objective is to evaluate these models for applicability to high pressure hydrogen environments.
Russell, D. A.↗
Unraveling Emergent Quantum States in Magnetic Topological Insulators using High Pressure Neutron Scattering
This proposal aims to uncover novel quantum phenomena under high pressure and understand the pressure effects on the atomic electronic interactions in magnetic topological materials. This program supports a combined neutron scattering and materials discovery of novel magnetic materials that display the coexistence of magnetism plus other physical phenomena such as a non-trivial electronic band topology under high pressure. The goal of this project is to close a long-standing knowledge gap in quantum materials research by developing a high-pressure neutron scattering (HP-NS) toolbox to systematically determine the magnetic structures and electronic interactions present at high pressure.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
In-situ study of rules of nanostructure evolution, severe plastic deformations, and friction under high pressure
Severe plastic deformations under high pressure are used to produce nanostructured materials but were studied ex-situ. Rough diamond anvils are introduced to reach maximum friction equal to yield strength in shear and the first in-situ study of the evolution of the pressure-dependent yield strength and radial distribution of nanostructural parameters are performed for severely pre-deformed Zr. ω-Zr behaves like perfectly plastic, isotropic, and strain-path-independent and reaches steady values of the crystallite size and dislocation density, which are pressure-, strain- and strain-path-independent. However, steady states for a-Zr obtained with smooth and rough anvils are different, causing major challenge in plasticity theory. In-situ study of severe plastic deformation of α-Zr with rough diamond anvils revealed that pressure-dependent yield strength, crystallite size, and dislocation density are getting steady and plastic strain- and strain-path-independent.
36 MATERIALS SCIENCE↗
Generalization of low pressure, gas-liquid, metastable sound speed to high pressures
A theory is developed for isentropic metastable sound propagation in high pressure gas-liquid mixtures. Without simplification, it also correctly predicts the minimum speed for low pressure air-water measurements where other authors are forced to postulate isothermal propagation. This is accomplished by a mixture heat capacity ratio which automatically adjusts from its single phase values to approximately the isothermal value of unity needed for the minimum speed. Computations are made for the pure components parahydrogen and nitrogen, with emphasis on the latter. With simplifying assumptions, the theory reduces to a well known approximate formula limited to low pressure.
Bursik, J. W.↗