Search NASA⌕ Search

SEARCH · Search NASA

Results for “High Pressure Hydrogen Storage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

196 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Nano-Engineered Catalyst Supported on Ceramic Hollow Fibers for the Utilization of CO 2 in Dry Reforming to Produce Syngas

The objective of this project was to develop a novel catalytic reactor containing nano-engineered catalysts for the utilization of CO 2 (captured from coal-fired power plants and other CO 2 emitting sources) in dry methane reforming (DMR) (CO 2 + CH 4 → 2 H 2 + 2 CO) to produce synthesis gas (syngas). The technology aims to reduce CO2 emissions by developing beneficial uses for CO 2 from coal-fired power plants. It also offers an alternative to mitigate CO 2 emissions in areas where geologic storage may not be an optimal solution and/or utilization could significantly offset the costs of carbon capture and sequestration. The nano-engineered Ni-based catalyst was prepared by atomic layer deposition (ALD). The Ni particles were as small as ~2-4 nm. The nano-engineered catalyst showed CH 4 conversion >95%, H 2 /CO ratio in the range of 0.7-1.0, and CH 4 reforming rate as high as 2,500 L/h/gNi at 850 ºC and pressure of 15-25 psia. The Ni-based ALD catalyst also showed good stability in DMR reaction during a 200-h continuous operation at 850 °C. This is due to strong bonding between the nanoparticles and substrates since the Ni nanoparticles were chemically bonded to the substrate during the ALD process. The high thermal stability maintains the high dispersion of Ni nanoparticles, which can inhibit coke formation because their step edges are small enough to limit carbon nucleation and growth. Technoeconomic analysis (TEA) indicates the levelized cost of syngas (LCOS) is $172/ton with our technology, which is lower than the equivalent (molar) cost of hydrogen produced by steam methane reforming (SMR) or autothermal reforming (ATR). The major operating cost is natural gas feed and fuel, and the levelized cost is highly sensitive to the price of natural gas and relatively insensitive to the CAPEX. Revenues from syngas could have a significant impact on the net cost of electricity (COE), depending on the cost of natural gas and the selling price of syngas, estimated at $36 per MWh if the syngas were sold at $195 per ton. Following DOE NETL’s guidance, a lifecycle analysis (LCA) was conducted to compare with SMR. The functional unit for the basis of comparison was defined as 1kg carbon monoxide in the product stream. The global warming potential (GWP) of our process was found to be 40% lower than the state-of-the-art SMR process. The sensitivity analysis confirms the emissions are most sensitive to the natural gas fuel requirements to deliver heat to the process.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

MODELS FOR ESTIMATING THE AUTOFRETTAGE PRESSURE AND RESIDUAL STRESSES IN WALLS OF TYPE 2 PRESSURE VESSELS

Autofrettage is a manufacturing process used during fabrication of Type 2 pressure vessels designed for usage at high pressures to enhance the fatigue life. The process locks high compressive residual stresses in the vessel’s liner wall that reduce the maximum and the mean stress during service loading. To achieve a consistent residual stress profile across the wall of the vessel, the choice of autofrettage pressure is critical. Several finite element analyses runs were conducted to estimate the correct autofrettage pressure that is a function of the yield strength of the liner material, the wall thickness, and the outside diameter of the liner for a wrap thickness of 17.06 mm (48 wire layers). From the finite element analyses results, models were developed to estimate the correct autofrettage pressure and the residual stress distribution across the liner wall as a function of the yield strength of the liner material, the wall thickness, and the outside diameter of the liner.

08 HYDROGEN↗
DOE OSTI2026

Cummins PEM Fuel Cell System for Heavy Duty Applications

The motivation for this project was to develop a high-pressure 100+ kW fuel cell stack that can be used in a modular fashion to power HD applications up to 1 MW. One of the issues that was identified during fuel cell system integration was the need for extra space for heat rejection systems(radiators) as well as additional fans and associated energy consumption to compensate for lower operating temperatures of fuel cells compared to internal combustion (IC) engines. To maximize the heat rejection capability of existing water-based coolant systems that are prevalent on IC engine-based systems, fuel cell stack design was developed to withstand and operate at IC engine coolant temperatures or higher, which in turn helps to reduce the radiator size requirement.

08 HYDROGEN↗
DOE OSTI2024

Key results from examinations of seven high burnup pressurized water reactor spent nuclear fuel rods

At present, spent nuclear fuel (SNF) assemblies discharged from US commercial power plants are placed into dry storage following a short cooling time (<10 years) in the plant’s spent fuel pool. The process of packaging the spent fuel into dry-storage canisters includes a drying step to remove residual water from the canister. During the drying process, the fuel rod cladding may reach temperatures as high as 400°C. Oak Ridge National Laboratory (ORNL) is performing destructive examinations of high burnup (HBU) (>45 GWd/MTU) SNF rods to address knowledge and data gaps related to extended interim storage and eventual transportation for disposal. The rods examined include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO, and M5. Three rods were subjected to a thermal transient to assess the effects of decay-heat-driven high temperatures expected during vacuum drying of the fuel as it is prepared for interim dry storage. The examinations focus on the composite fuel rod performance, as compared with the performance of defueled rod cladding, and establish the baseline mechanical properties of a fuel rod before interim dry storage. The key results of these examinations are presented, including the measured mechanical and fatigue properties, observations of cladding hydrogen pickup and hydride reorientation effects on rod performance, effects of the simulated drying temperatures on rod performance, and general conclusions of SNF performance in extended interim dry storage and transport. The rods were found to be strong and durable in the expected loading conditions, even considering the formation of radial hydrides associated with vacuum drying. The combined testing provides a broad body of data supporting extended interim storage and transportation performance of HBU spent fuel.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Williston Basin Resource Study for Commercial-Scale Subsurface Hydrogen Storage

The Energy & Environmental Research Center (EERC), in partnership with the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL), the EERC’s State Energy Research Center (SERC), MPLX Operations LLC, and TC Energy Development Holdings Inc. (a subsidiary of TC Energy Corporation), studied the potential for subsurface hydrogen storage and recovery in the Williston Basin of western North Dakota. The project’s goal was to evaluate the feasibility of large-scale, secure geologic H 2 storage to support future hydrogen generation, storage, and use. This work included laboratory testing, H 2 –rock–fluid exposure experiments, literature reviews on H 2 embrittlement, and reservoir modeling and simulations. The study included an assessment of storage potential across three types of storage reservoirs using both reservoir simulation and DOE’s web-based tool SHASTA-HELP (Subsurface Hydrogen Assessment, Storage, and Technology Acceleration – Hydrogen Estimator for Logistical Planning), as well as investigation of potential H 2 production and markets for commercial-scale deployment. Building on prior EERC gas storage research, three storage options were selected for detailed evaluation: the Broom Creek Formation (a clastic saline reservoir), the Dickinson Lodgepole Mounds (DLM) complex (carbonate mud mound structures) of the Lodgepole Formation (an active oil and gas producing reservoir), and the Dunham Salt Interval of the Piper Formation (to be used for engineered salt cavern development). These targets were prioritized based on prior EERC research using datasets related to seal capacity, reservoir quality, mechanical integrity, and injectivity. Exposure tests on Broom Creek and DLM samples showed mineral dissolution and precipitation that increased brine salinity and altered reservoir rock surfaces. Although these results provide useful insight, they are limited by small sample sizes and short-term (30-day) exposure, requiring further study to assess long-term storage integrity. Salt formations were not tested because of their known nonreactivity and established mechanical stability. Results of reservoir simulations performed for a single site demonstrated that the Broom Creek Formation may be capable of receiving up to 42,000 tonnes of injected H 2 over 7 months via one well. H 2 recovery took place over 5 months, resulting in approximately 26,000 tonnes (~62% without cushion gas [CG]). This work suggests water production may be important and subsequent cycles of injection and production may perform more efficiently; however, significant site-specific work in the future is needed to assess actual reservoir performance of injection and withdrawal of H 2 storage. For oil reservoir potential, a multiple-well model was used to simulate injection of approximately 32,000 tonnes of H 2 into a single wellbore while simultaneously producing in place reservoir fluids from four offset wells to maintain reservoir pressure. The simulation results suggested a high recovery (~98%); in addition, cost advantages through existing infrastructure could be realized. Challenges in this reservoir include vi managing gas purity and leakage risks. In both scenarios, production of H 2 takes place in a single-well scenario with 10 cycles (7 months of injection and 5 months of production) over 10 years. Finally, the use of engineered caverns in the Dunhan Salt was evaluated, and the results suggest that while they have a smaller capacity (<1000 tonnes per cavern), they exhibit nearly complete gas recovery (>99%), fast response times, and low purity risk. While caverns in North Dakota may be smaller in capacity, fields can be developed in galleries to accommodate the volumetric needs and rapid turnaround times necessary to meet market demands. Geographic limitations and thin salt intervals in North Dakota may represent less total storage potential than salt domes elsewhere, but significant opportunities exist to expand this market for gas storage in North Dakota. A basinwide assessment was performed to estimate a first-of-its-kind value for H 2 storage on a large scale. DOE’s SHASTA-HELP, combined with EERC simulation work, was used to perform the assessment. Estimated H 2 storage potential varied widely for each formation type. The Broom Creek saline formation was estimated to have a storage potential of approximately 1.7–90.5 million tonnes (MMt). The DLM oil reservoirs were estimated to have 0.07–0.19 MMt of capacity. Notably, each of these estimates relies on significant assumptions regarding reservoir thickness, porosity, permeability, and CG needed for operation. Much research is needed to understand the true site-specific storage resource potential of each formation. Using the Dunham Salt Interval for cavern development may result in as much as 4.79 MMt (up to 2.87 MMt working gas) of H 2 storage potential. An important note for consideration is that the values presented here need significantly more geological characterization and engineering assessments prior to gaining confidence in performance. This will be a focal point for future research and development needs. The basinwide evaluation also indicated that North Dakota has significant H 2 generation potential, with estimates up to a possible 13 MMt annually, suggesting a substantial opportunity for H 2 market development and thus the need for commercial-scale H 2 storage to facilitate growth and resilience. Key Recommendations 1. Conduct detailed site characterization (3D seismic, well logs, core sampling) to reduce geologic uncertainty. 2. Perform techno-economic analyses incorporating market, regulatory, and incentive frameworks. 3. Investigate long-term interactions among H 2 , CGs, well materials, and formations to assess risks. 4. Develop pilot- and field-scale demonstrations to validate models and establish best practices.

03 NATURAL GAS↗
DOE OSTI2023

Mechanisms of adsorbing hydrogen gas on metal decorated graphene

Hydrogen is a key player in global strategies to reduce greenhouse gas emissions. In order to make hydrogen a widely used fuel, we require more efficient methods of storing it than the current standard of pressurized cylinders. An alternative method is to adsorb H 2 in a material and avoid the use of high pressures. Among many potential materials, layered materials such as graphene present a practical advantage as they are lightweight. However, graphene and other 2D materials typically bind H 2 too weakly to store it at the typical operating conditions of a hydrogen fuel cell, meaning that high pressure would still be required. Modifying the material, for example by decorating graphene with adatoms, can strengthen the adsorption energy of H 2 molecules, but the underlying mechanisms are still not well understood. In this work, we systematically screen alkali and alkaline-earth metal decorated graphene sheets for the static thermodynamic adsorption of hydrogen gas from first principles and focus on the mechanisms of binding. We show that there are three mechanisms of adsorption on metal decorated graphene and each leads to distinctly different hydrogen adsorption structures. The three mechanisms can be described as weak van der Waals physisorption, metal adatom facilitated polarization, and Kubas adsorption. Among these mechanisms, we find that Kubas adsorption is easily perturbed by an external electric field, providing a way to tune H 2 adsorption. In conclusion, this work is foundational and builds our understanding of H 2 adsorption under idealized conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A Highly Efficient and Affordable Hybrid System for Hydrogen and Electricity Production (Final Project)

The pursuit of clean, secure, and sustainable energy has sparked significant interest in fuel cells for power generation and electrolyzer cells for hydrogen production. Among all types of fuel and electrolyzer cells, solid oxide cells (SOCs) have emerged as promising candidates due to their high efficiency and versatility. However, conventional oxygen-ion conductive SOCs face several challenges related to their performance and durability associated with their high-temperature operation (≥ 800 ºC). This has led to a growing interest in intermediate-temperature (≤ 650 ºC) proton-conducting solid oxide cells (p-SOCs) as potential alternatives. In collaboration between Phillips 66 and Georgia Tech, this project aims to achieve a 1 kW p-SOCs system to demonstrate the commercial viability of efficient SOC systems. This report addresses four primary areas and key challenges we overcame: (1) development of efficient and durable proton-conducting electrolyte (e.g., BaHf 0.1 Ce 0.7 Yb 0.2 O 3-δ ) and electrode/catalyst materials, (2) large area cell fabrication (10 x 10 cm 2 ), (3) scalable stack design and building (250 W and 1 kW), and (4) demonstration of a 1 kW prototype system. Notably, significant challenges faced during the large area cell fabrication process were addressed by achieving cell flatness, improving fabrication yield, and ensuring electrode/electrolyte interfacial adhesion. Stack designs were also developed, focusing on reducing contact resistance and optimizing stack components (e.g., sealants). These efforts resulted in the achievement of high performance and durability with promising outputs of 250 W and 1 kW. Furthermore, the integration of these stacks into a fuel-powered system was explored, with refinements made to heat management, as well as to pressure and heating conditions. The results demonstrated the potential applicability of our p-SOC technology in commercial energy storage and power generation systems. Additionally, the report discusses techno-economic analysis and a market transformation plan, aiming to evaluate and advance the commercial feasibility of this technology.

25 ENERGY STORAGE↗
DOE OSTI2020

Heterolytic Scission of Hydrogen Within a Crystalline Frustrated Lewis Pair

We report the heterolysis of molecular hydrogen under ambient conditions by the crystalline frustrated Lewis pair (FLP) 1-{2-[bis(pentafluorophenyl)boryl]phenyl}-2,2,6,6-tetramethylpiperidine (KCAT). The gas–solid reaction provides an approach to prepare the solvent-free, polycrystalline ion pair KCATH2 through a single crystal to single crystal transformation. The crystal lattice of KCATH2 increases in size relative to the parent KCAT by approximately 2%. Microscopy was used to follow the transformation of the highly colored red/orange KCAT to the colorless KCATH2 over a period of 2 h at 300 K under a flow of H2 gas. There is no evidence of crystal decrepitation during hydrogen uptake. Inelastic neutron scattering employed over a temperature range from 4–200 K did not provide evidence for the formation of polarized H2 in a precursor complex within the crystal at low temperatures and high pressures. However, at 300 K, the INS spectrum of KCAT transformed to the INS spectrum of KCATH2. Calculations suggest that the driving force is more favorable in the solid state compared to the solution or gas phase, but the addition of H2 into the KCAT crystal is unfavorable. Ab Initio methods were used to calculate the INS spectra of KCAT, KCATH2, and a possible precursor complex of H2 in the pocket between the B and N of crystalline KCAT. Ex-situ NMR showed that the transformation from KCAT to KCATH2 is quantitative and our results suggest that the hydrogen heterolysis process occurs via H2 diffusion into the FLP crystal with a rate-limiting movement of H2 from inactive positions to reactive sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Carbon Dioxide Utilization for Plasma Nanosynthesis of Carbon

This DOE Phase I SBIR project has developed a glow discharge-based plasma process to convert carbon dioxide to sold carbon and water. By adding natural gas, the additional enthalpy can be used to reform the output carbon dioxide to value added carbon and EPA-compliance-grade water, thus creating a process that has no gaseous products at all, such as: CO 2 + CH 4 → 2C + 2H 2 O, which is simply the exothermic reverse of the syngas reaction. During the Phase I work, several milestones were accomplished successfully. a. First, a synthesis reactor was designed, assembled, and successfully operated using the combined simultaneous operation of glow discharge and microwaves. DC discharge and microwaves can also be operated individually, allowing multiple configurations to be used This is one of the first reactors of its kind, and perhaps the first ever. b. Second, the research team successfully produced carbon nanomaterials using carbon dioxide as the source of carbon via CO 2 + 2H 2 → C + 2H 2 O. This is certainly one of the first processes to use plasma to convert carbon dioxide to nanocarbon, and perhaps the first ever demonstration. c. Third, it was also shown that carbon monoxide and carbon dioxide can be used with methane to reduce the synthesis temperature of ASI graphene decorated carbon nanotubes (GDCNT). Hitherto GDCNT were only fabricated above 1200 °C. GDCNT was synthesized at 780 °C. CO 2 + C → 2CO; 2 CO + CH 4 → 3 C + 2H 2 O, and also, CH 4 + CO 2 → 2 C + 2H 2 O. d. Fourth, closed cycle synthesis of nanomaterial was demonstrated with over 80% conversion of carbon dioxide to carbon and water was achieved, on the basis of pressure drop during glow discharge. e. Fifth, plasma operation was achieved via glow discharge and microwaves at 500 Torr, demonstrating a path forward to atmospheric pressure operation f. Sixth, using carbon monoxide and carbon dioxide in an electrothermal furnace, we produced 350 grams per hour of high-quality nanotubes in a single furnace, compared to 200 grams per hour for the commercial process. Controlling the enthalpy prevents self-extinguishing hot gas pyrolysis. Thus, carbon dioxide enhances the properties and reduces the production cost. This is a near term advance that can go into trial production in the near term. g. Seventh, economic analysis suggests an economic plan forward, producing carbon nanotubes for less than $50 per pound. The use of hydrogen and carbon dioxide as the feedstocks is acceptable from a cost basis, and in fact hydrogen is less expensive than carbon monoxide. Niche applications are available in the near term, though quantities relevant to sequestration remain a far-term goal. h. Eighth, though it was not the research team’s intention to create a new process for producing carbon monoxide, it was realized that almost by accident we demonstrated plasma reforming of carbon dioxide via a plasma version of the reverse Boudouard reaction. Accordingly, we have contacted a major gas manufacturer (Matheson Gas) to determine whether there is interest in creating an industrial version of the process. i. Ninth, a long-range strategy is identified in which a progressively more carbon-conscious world will seek to create solid carbon as a means of sequestering carbon dioxide, impeding its return to the atmosphere. In the long term the price must drop by orders of magnitude with larger production, and assuming success, solid carbon could be the preferred form for sequestration rather than underground storage. If carbon can be made as cheaply as dirt, or nearly so, then it can serve a useful purpose as structural material for housing, soil amendments in agriculture and fillers to modify low areas.

03 NATURAL GAS↗
DOE OSTI2025

Develop a Simulation Framework for Understanding Physico-Chemical Processes and Optimization of CHZ' Plastic Thermolyze Technology (CRADA Final Report)

Thermolyzer(TM) technology is a third-generation, multi-reactor, oxygen-free, low pressure, slow pyrolysis process. It has proven to be remarkably versatile in successfully processing all types of hydrocarbon waste. These include all seven types of plastics, tires, auto shredder residue, carpet, electronic waste, and composites. Working with the IACMI, Thermolyzer(TM) technology has recovered the glass and carbon fibers from wind turbine blades for reuse into new applications. Its primary output is a synthesis gas that is rich in H 2 , CH 4 , and small amounts of C 2-4 aliphatic hydrocarbons. Other components are CO and CO 2 . Three unique features set Thermolyzer(TM) apart from other pyrolysis systems: the syngas is clean enough to run in Siemens or Solar gas turbines or IC engines without fouling, clean, salable, byproducts are produced, and CO 2 emissions are lower than natural gas power plants. Research results have been obtained from an operating 7 ton/day facility. A 44 ton/day plant has successfully operated as noted above. The process works because it makes use of the recoverable embodied energy in the feedstock. Surprisingly, a pound of some plastics has the same recoverable energy content as a pound of gasoline. Thus, it is imperative to develop a process that economically converts scrap plastics (including ocean plastics) into energy and thereby conserve the non-renewable fossil fuels for future generations. The Thermolyzer(TM) technology can also be used to create liquid fuels like gasoline and diesel from hydrocarbon wastes. Because of the high hydrogen content of the synthesis gas, hydrogen can be recovered more inexpensively than the current solar or wind energy being used to electrolyze water. That hydrogen can be used for fuel cell powered vehicles or converted into ammonia for agriculture or as a hydrogen storage medium. Extension of this technology to other wastes such as tires, auto shredder residue or wood wastes would expand the circular economy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling of ATR fuel in DOE Standard Canisters with Helium Backfilled Condition

Road-ready and final disposition packaging configurations for the advanced test reactor (ATR) fuel dictates storage within helium backfilled sealed DOE standard canisters. These sealed canisters are intended for extened (>50 year) dry storage). The typical packaging configuration for the 15-foot DOE canisters places 10 ATR elements within a Type 1a basket, and three baskets are loaded within each DOE canister. During in-reactor operations and cooling pond storage conditions, oxyhydroxide layers form on the surface of the aluminum clad fuel. These layers produce hydrogen gas over time due to the fuel’s radiation field. As part of the packing procedure, the ATR fuel should be dried to remove any residual physio-/chemi- sorbed water from the surface. As testing to the effectiveness of the drying procedure is still underway, this modeling will include results at fully saturated and fully dried conditions. In previous modeling efforts, the G-value for the production of hydrogen from the oxyhydroxide layers was assumed to be in argon environments as measured by Task 2 - Oxyhydroxide Layer Radiolytic Gas Generation Resolution. Previous experimental testing showed differences in the hydrogen generated based on the gaseous environment. In the associated experimental work, Task 2 - Oxyhydroxide Layer Radiolytic Gas Generation Resolution, additional tests were completed in a helium environment, and updated G-values for the radiolytic production of hydrogen from the oxyhydroxide layers were provided. These values are 28% and 58% higher than values for argon. In addition, a change to the modeling of the oxyhydroxide radiolysis has been made from previous reports. This change assumes the dependency of the dose rate on the overall reaction rate is applied to the total weight of the sample, rather than to just the weight of the oxyhydroxide layer. This decreases the dependency of the radiolytic reaction on the thickness of the oxyhydroxide layer. For a nominal scenario of stored ATR fuel, assuming the chemi-/physio- sorbed water have been fully removed, the internal canister pressure increases to 1.61 atm over a 50 year period, with a hydrogen mole percentage of 21%. As in previous modeling, any oxygen present is in negligible amounts (<1 ppt). If a small amount residual air is present, nitric acid can form up to 1300 ppm. For a scenario with high fuel decay heat, the model shows internal pressure increasing to 2.1 atm, with 39.3 mole percentage of hydrogen. In a scenario where significant chemi-/physio- sorbed water is present within the corrosion layer, the nominal scenario shows a pressure increase to 2.54 atm, with 21.1 mole percent hydrogen. The high decay heat case shows a pressure increase to 3.18 atm with 39.9 mole percent hydrogen.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Multi-Functional Distributed Fiber Sensors for Pipeline Monitoring and Methane Detections. Final Report

As an abundant and cheap fossil energy source, natural gas has become a significant energy supply to support the United States’ economy. However, the large-scale extraction and utilization of natural gas also impose significant challenges on methane leakage. This problem is exacerbated by aging gas utility delivery systems, including interstate high-pressure pipelines, storage, and transmission facilities. This project aims to develop a cost-effective fiber optical sensing method that can perform multi-parameter real-time measurements of natural gas pipelines across long interrogation distances up to 100 km with 1-meter spatial resolution. This sensing tool can evaluate overall pipeline efficiency and reduce methane emissions for mid-stream methane infrastructures. To accomplish this objective, research and development efforts funded by this project have resulted in the following accomplishments: This project successfully has developed new functional sensory polymer materials using Metal-Organic Frameworks (MOFs) that can be coated on optical fiber through the reel-to-reel coating process. Functional polymer-coated optical fibers can perform sensitive methane detection through evanescence wave interaction and strain-based measurements to achieve 1% detection sensitivities. The new sensors fibers support both distributed measurements and multiplexed fiber sensors array for multi-point measurements. This project developed and optimized a new multi-core optical fiber that supports simultaneous and distributed measurements of strain and temperatures with 1-meter spatial resolutions across up to 100-km interrogation distance. This new fiber, combined with sensory polymercoated fiber, could perform both distributed temperature and methane detections. This project developed a new artificial intelligence big data algorithm approach that can effectively analyze high-resolution data harnessed by distributed fiber sensors to protect natural gas pipelines against external threats and detect internal defects induced by corrosion. Working with our industry partner, this project developed new optical fibers that support fiber sensor fabrications through polymer coating after the fibers are drawn. These new fibers eliminate the need for direct sensor fabrication when the fiber is fabricated on a fiber draw tower, which drastically expands fiber sensors' applicability. This research project has significantly advanced the distributed fiber sensing technology. It will dramatically increase the applicability and adaptability of distributed fiber sensors for a wide array of applications in energy, sustainability, and environmental science, including structural health monitoring of natural gas pipelines, oil infrastructures, hydrogen facilities, and environmental monitoring of carbon storage sites, water supply systems, and others.

03 NATURAL GAS↗
DOE OSTI2021

Slot-die-coating operability windows for polymer electrolyte membrane fuel cell cathode catalyst layers

Roll-to-roll (R2R) slot-die coating of polymer electrolyte membrane fuel cell (PEMFC) catalyst layers represents a scalable deposition method for producing 10–20 m 2 ·min -1 of catalyst-coated gas diffusion layers (GDLs). This high-throughput production technique will help lower the cost of PEMFC catalyst layers. The uniformity of the wet layer applied by slot die deposition is affected by process parameters such as substrate speed, vacuum pressure applied at the upstream meniscus, gap between the slot die lips and substrate, ink rheology, and other ink and substrate properties. The set of conditions for producing a defect-free coating with a dilute ink typically requires little to no upstream vacuum pressure, so suitable operating conditions can be found easily through trial and error and operator intuition. However, the higher viscosity of more concentrated inks dramatically shifts the range of settings that result in a homogeneous coating to higher vacuum levels, which are harder to find through hit or miss. A predictive model showing the range of operable conditions decreases material wastage inherent in experimentally searching for suitable parameters. In this study, the defect-free coating parameter window is explored experimentally and theoretically for two concentrations of PEFC cathode inks. Both a full capillary hydrodynamic model and a computationally cheaper viscocapillary model successfully predict the experimentally determined coating window within the experimental and model uncertainty limits for inks with 5.3 wt% and 12.0 wt% solids ink while maintaining the 0.1 mg Pt ·cm -2 Pt areal loading target. Here, this paper demonstrates a viable pathway for meeting the $30/kW net ultimate cost target of the United States Department of Energy (U.S. DOE) Hydrogen Fuel Cells Technologies Office (HFTO). The concentrated ink lowers the thermal energy and capital expenditure (CapEx) budget of the coating process by decreasing the amount of time, energy, and floorspace required for drying the coating.

25 ENERGY STORAGE↗
DOE OSTI2020

BWR Spent Nuclear Fuel Acquisition and Testing to Support DOE-NE High Burnup Spent Fuel Data Project

The Office of Spent Fuel and Waste Disposition (SFWD) within the US Department of Energy (DOE) Office of Nuclear Energy (NE) established the Spent Fuel and Waste Science and Technology (SFWST) campaign to conduct research and development (R&D) activities related to the storage, transportation, and disposal of spent nuclear fuel (SNF) and high-level radioactive waste. The SFWST program was created within SFWD to address issues of extended or long-term SNF storage and transportation. Some near-term objectives of SFWST are to use a science-based, engineering-driven approach to: Support the enhancement of the technical bases to support the continued safe and secure dry storage of SNF for extended periods; Support the enhancement of the technical bases for retrieving SNF after extended dry storage; Support the enhancement of the technical bases for transporting high burnup (HBU) fuel and transporting low burnup fuel and HBU fuel after dry storage DOE-NE, in partnership with the Electric Power Research Institute, developed the High Burnup Spent Fuel Data Project to perform a large-scale demonstration and laboratory-scale testing of HBU pressurized water reactor (PWR) fuels (exceeding 45 gigawatt-days per metric ton of uranium [GWd/MTU]). Under this project, 25 sister rods—which are rods that have the same design, power histories, and other characteristics—were removed from assemblies at the North Anna Nuclear Power Station and sent to Oak Ridge National Laboratory (ORNL) in January 2016. ORNL performed detailed nondestructive examination (NDE) on all 25 rods. The NDE consisted of visual examinations, gamma and neutron scanning, profilometry and rod length measurements, and eddy current examinations. After completing the NDE, 10 of the sister rods were delivered to Pacific Northwest National Laboratory (PNNL) in a NAC International, Inc. legal-weight truck cask in September 2018 for destructive examination (DE). To date, SFWD work has focused on the PWR fuel that is part of the Sister Rod Test program. No boiling water reactor (BWR) fuel has been tested in the program, and the data needs that were identified for the PWR fuel have not been collected for BWR fuel. The goal to obtain six to nine BWR rods and test them at ORNL will support closing this important data gap. BWR fuel comprises approximately 56% of the total fuel assemblies currently in storage at nuclear power plants in the United States. BWR nuclear fuel and cladding designs and manufacturing are significantly different from PWRs. Differences include the following: BWR fuel pellets are larger than PWR pellets; Variations of Zircaloy-2 (including liners) are used instead of the Zircaloy-4 cladding materials used in PWRs; Clad manufacturing and stress-relief processes are different between PWRs and BWRs; The fuel rod dimensions are different because larger rod diameters and thicker cladding are used in BWRs; BWR fuel typically has lower internal rod pressures and sees vastly different operating conditions than PWR fuel (i.e., two-phase flow); BWR assemblies are “canned,” meaning each assembly is surrounded by a metal fuel channel; BWR cladding is often composed of an inner pure Zr liner that has widely different mechanical properties than the Zircaloy-2 alloy and exhibits a stronger affinity for hydrogen; The BWR SNF generally has more total hydrogen in the cladding/liner than typical PWR fuel; The construction of the PWR and BWR assemblies is vastly different; BWR rods are solidly attached to the assembly nozzles and experience a much different vibration and shock load than PWR rods, which are “floating” within a grid system attached to guide tubes, and the rods sit loosely on the bottom end plates. These numerous differences will affect the way the BWR SNF responds under dry storage preparation processes (e.g., vacuum drying) and during transportation. The results collected in the PWR experimental program must be compared with a subset of similar data collected on BWR SNF to establish a technical basis for whether the larger PWR database is sufficient to bound the BWR SNF end-of-life conditions as is currently assumed for several fuel/clad properties. Changes that occur in both fuel types at HBU could exacerbate any mechanical property differences. As the fuel burnup increases, several changes occur that might affect the performance of the fuel, cladding, and assembly hardware in storage and transportation. These changes include increased cladding corrosion layer thickness, increased cladding hydrogen content, increased cladding creep strains, increased fission gas release, and the formation of the HBU structure at the surface of the fuel pellets. The Nuclear Regulatory Commission (NRC) limits the current maximum rod-averaged burnup to 62 GWd/MTU due to these changes and the lack of data at higher burnups.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Extended Modeling of DOE Sealed Canisters with Updated Chemistry Models

Road-ready and final disposition packaging configurations for the advanced test reactor (ATR) fuel currently specifies storage within helium backfilled DOE sealed standard canisters. The aluminum cladding of the ATR fuel contains an oxyhydroxide layer of boehmite/bayerite that generates hydrogen when subjected to irradiation. Understanding the effect of this hydrogen buildup over time to important for long term storage considerations. Previous modeling efforts have built a coupled CFD-chemical model to simulate the temperature gas phase concentrations within the DOE sealed standard canisters. These models have coupled the temperature conditions to both the gas phase radiolysis chemistry and the surface chemistry associated with the oxyhydroxide layer. The previous iteration of the model utilized constant G-values for the hydrogen generation a 50-year period. This new iteration of the model utilizes new experimental data to update the hydrogen generation rate, as well as increase the simulated time to a 200-year period. Given the half-life assumed for the primary Cs-137 isotope responsible for gamma radiation in the ATR spent fuel, the 200-year period decreases the decay heat and dose rate of the spent fuel by a factor of 100, which combined with the updated chemistry substantially decreases new hydrogen generation. Continued experimental work has identified trends for aluminum surrogate samples with oxyhydroxide layers for tests done at higher dose rates. At low initial doses a fast generation rate of hydrogen occurs which starts to roll over to a lower generation as the total dose applied increase. A small-scale chemical model was built to replicate as mini-canister surrogate system at SRNL as well as for the smaller capsule tests performed at INL. A variety of chemical models to capture this effect were tested, and a back reaction of H radical absorbing onto the surface, or inhibition of the reaction by significant H 2 cover gas were both able to fit both the mini-canister and the small capsule test data. Both kinetic fits were used to generate data from the new 200-year simulation. As additional experiments continue, the kinetic fits may be adjusted to adapt to new data. However, updated data shows that hydrogen atmosphere has little effect on actual generation data, so the model was reverted to use a star-stepped G-value for low-dose and high-dose regions. For the undried fuel case, the three models differ significantly with an end concentration of 1% for back reaction, 4.2% for inhibition, and 13.1% for constant G-value for the nominal scenario. For the dried fuel case, the nominal cases showed end concentrations of 0.23% for back reaction, 1.9% for inhibition, and 4.2% for const G-value for the nominal scenario. For the constant G-value case that is less conservative than the other two, the pressure for undried fuel increases to 1.94 atm over 200 years for the nominal case and 2.11 atm for the high decay heat case. The total hydrogen concentration after 200 years is 4.92% for the low decay heat case and 27.4% for the high decay heat case for undried fuel and is 1.4% and 9.6% for low and high decay heat fuel for the dried fuel case. If small amount of residual air is present, the potential for nitric acid formation of 595, 1568, and 2816 ppm for the lower, nominal, and upper fuel decay heat can occur. At long-term timeframes no significant shift in major species present occurs, so no appreciable amount of oxygen is present in the system. The continued rate of hydrogen generation in the canister occurs at an increase of 0.04% by mole over the final 10 years. Increasing the model range out to 1000 years continues to drop the hydrogen generation rate through decreasing dose rate.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Energy Frontier Research Centers: Center for the Computational Design of Functional Layered Materials (CCDM) August 1, 2014 - July 31, 2018; Center for Complex Materials from First Principles (CCM) August 1, 2018 - July 31, 2021 (Final Report)

The mission of the DOE Energy Frontier Research Centers CCDM (2014-2018) and CCM (2018-2021) was to theoretically develop, computationally apply, and experimentally validate electronic structure methods for all materials, with a focus on the complex materials, especially layered and two-dimensional materials, strongly-correlated materials, and liquid water. This was achieved by over 200 published journal articles authored by about 17 senior investigators from physics and chemistry and from theory, computation, and experiment, plus their collaborators. In particular, the Centers confirmed the predictive power of the SCAN (strongly constrained and appropriately normed) density functional, which was constructed to satisfy 17 known exact constraints and several appropriate norms. Without being fitted to real bonded systems, and at a modest computational cost, SCAN correctly predicted covalent, ionic, metallic, hydrogen, and van der Waals bonds in many challenging materials. SCAN gave an improved description of defects in semiconductors, surface properties of metals, seven phases of ice, liquid water, liquid and supercooled silicon, subtle structural distortions in ferroelectrics, formation energies and structural predictions for solids, and critical pressures for structural phase transitions. Perhaps most remarkably, SCAN correctly described some strongly-correlated materials that were previously believed to be beyond the reach of density-functional approximations. SCAN is the only density functional that correctly predicts the band gap closing under chemical doping of the cuprate high-temperature superconducting materials. SCAN also predicts a landscape of competing stripe and magnetic phases in the cuprates. For some materials with some codes, SCAN has convergence problems that are greatly reduced by the CCM-developed r 2 SCAN, without loss of accuracy or rigor. SCAN and r 2 SCAN still make some self-interaction error, which is greatly reduced by the CCDM/ CCM-developed local orbital scaling correction (LOSC). These Centers further proved that the fundamental energy gaps of a solid from an orbital energy difference and from total energy differences are the same for a large class of generalized Kohn-Sham (GKS) functionals, including SCAN and standard hybrid functionals, and that symmetry breaking arises when a dynamic density fluctuation drops to zero frequency. The Centers identified new mechanisms for catalysis in layered materials with ions intercalated between the layers, investigated charge density waves both in model systems and in real layered materials, studied changes of band gap with the number of layers, and explored topological ultrathin films, bent nanoribbons, and defects.

08 HYDROGEN↗