Search NASA⌕ Search

SEARCH · Search NASA

Results for “High aspect ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Modeling the Yaw Behavior of Tail Fins for Small Wind Turbines: November 22, 2021 - May 21, 2024

This report describes the aerodynamic modelling of the yaw behavior of tail fins for small wind turbines (SWTs). The analysis is based on unsteady slender body theory (USBT) and is formulated to be used with the proposed tail fin module to be added to OpenFAST. Linearized USBT, which has been applied in the past to SWT tail fins, is developed in three main ways. First, USBT is extended to high yaw angles and aspect ratios by modelling the associated nonlinear vortex dynamics and the chordwise load distribution respectively. Second, we consider the effect of time-varying wind speed. The extended theory is compared to recent unpublished measurements at the University of Perugia, Italy, for the yaw behavior of delta, elliptical, and rectangular tail fins without a rotor and nacelle. The fins were released from initial yaw angles of -40 degrees and -80 degrees ; the latter is of sufficient magnitude to show the importance of the nonlinear yaw dynamics. Further, the friction in the model tail fin bearings was measured and modelled. The constants in the aerodynamic models were taken from the literature but significant improvement in accuracy is achieved by using system identification techniques to optimize the values. This leads to the third main finding: extended USBT is accurate for all generic tail fin shapes that we considered and is, therefore, very suitable for inclusion in aeroelastic codes for SWTs. The final development is of a general nonlinear equation for yaw response that is simpler than the extended USBT and is also suitable for inclusion in OpenFAST. The two nonlinear models are used to highlight the geometric requirements for good tail fin design.

distributed wind↗
DOE OSTI2022

Probing the role of CNTs in Pt nanoparticle/CNT/graphene nanohybrids H 2 sensors

Abstract In the carbon nanotubes film/graphene heterostructure decorated with catalytic Pt nanoparticles using atomic layer deposition (Pt-NPs/CNTs/Gr) H 2 sensors, the CNT film determines the effective sensing area and the signal transport to Gr channel. The former requires a large CNT aspect ratio for a higher sensing area while the latter demands high electric conductivity for efficient charge transport. Considering the CNT’s aspect ratio decreases, while its conductivity increases ( i.e. , bandgap decreases), with the CNT diameter, it is important to understand how quantitatively these effects impact the performance of the Pt-NPs/CNTs/Gr nanohybrids sensors. Motivated by this, this work presents a systematic study of the Pt-NPs/CNTs/Gr H 2 sensor performance with the CNT films made from different constituent CNTs of diameters ranging from 1 nm for single-wall CNTs, to 2 nm for double-wall CNTs, and to 10–30 nm for multi-wall CNTs (MWCNTs). By measuring the morphology and electric conductivity of SWCNT, DWCNT and MWCNT films, this work aims to reveal the quantitative correlation between the sensor performance and relevant CNT properties. Interestingly, the best performance is obtained on Pt-NPs/MWCNTs/Gr H 2 sensors, which can be attributed to the compromise of the effective sensing area and electric conductivity on MWCNT films and illustrates the importance of optimizing sensor design.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

The Ice Particle and Aggregate Simulator (IPAS). Part II: Analysis of a Database of Theoretical Aggregates for Microphysical Parameterization

Abstract Bulk ice-microphysical models parameterize the dynamic evolution of ice particles from advection, collection, and sedimentation through a cloud layer to the surface. Frozen hydrometeors can grow to acquire a multitude of shapes and sizes, which influence the distribution of mass within cloud systems. Aggregates, defined herein as the collection of ice particles, have a variety of formations based on initial ice particle size, shape, falling orientation, and the number of particles that collect. This work focuses on using the Ice Particle and Aggregate Simulator (IPAS) as a statistical tool to repetitively collect ice crystals of identical properties to derive bulk aggregate characteristics. A database of 9 744 000 aggregates is generated with resulting properties analyzed. After 150 single ice crystals (monomers) collect, the most extreme aggregate aspect ratio calculations asymptote toward and ϕ ca ≈ 0.50 for aggregates composed of quasi-horizontally oriented and randomly oriented monomers, respectively. The results presented are largely consistent with both a previous theoretical study and estimates derived from ground-based observations from two different geographic locations. Particle falling orientation highly influences newly formed aggregate aspect ratios from the collection of particles with extreme aspect ratios; quasi-horizontally oriented particles can produce aggregate aspect ratios an order of magnitude more extreme than randomly oriented particles but can also produce near-spherical aggregates as the number of monomers comprising the aggregate reach approximately 100. Finally, a majority of collections result in aggregates that are closer to prolate than oblate spheroids.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

The High Fraction of Thin Disk Galaxies Continues to Challenge ΛCDM Cosmology

Any viable cosmological framework has to match the observed proportion of early- and late-type galaxies. In this contribution, we focus on the distribution of galaxy morphological types in the standard model of cosmology (Lambda cold dark matter, ΛCDM). Using the latest state-of-the-art cosmological ΛCDM simulations known as Illustris, IllustrisTNG, and EAGLE, we calculate the intrinsic and sky-projected aspect ratio distribution of the stars in subhalos with stellar mass M * > 10 10 M ⊙ at redshift z = 0. There is a significant deficit of intrinsically thin disk galaxies, which however comprise most of the locally observed galaxy population. Consequently, the sky-projected aspect ratio distribution produced by these ΛCDM simulations disagrees with the Galaxy And Mass Assembly (GAMA) survey and Sloan Digital Sky Survey at ≥12.52σ (TNG50-1) and ≥14.82σ (EAGLE50) confidence. The deficit of intrinsically thin galaxies could be due to a much less hierarchical merger-driven build-up of observed galaxies than is given by the ΛCDM framework. It might also arise from the implemented sub-grid models, or from the limited resolution of the above-mentioned hydrodynamical simulations. We estimate that an 8 5 times better mass resolution realization than TNG50-1 would reduce the tension with GAMA to the 5.58σ level. Finally, we show that galaxies with fewer major mergers have a somewhat thinner aspect ratio distribution. Given also the high expected frequency of minor mergers in ΛCDM, the problem may be due to minor mergers. In this case, the angular momentum problem could be alleviated in Milgromian dynamics because of a reduced merger frequency arising from the absence of dynamical friction between extended dark matter halos.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Experimental demonstration of transient CHI start-up using a floating biased electrode configuration

Transient coaxial helicity injection (CHI) current start-up in a spherical tokamak (ST) has been demonstrated for the first time using a reactor-relevant floating single biased (FSB) electrode configuration on QUEST. Unlike previous applications of CHI on HIT-II and on NSTX in which the entire ST vessel was split in two using two toroidal ceramic rings as vacuum breaks, in the FSB electrode configuration on QUEST, only the lower outer divertor plate is electrically insulated from the rest of the vessel. This is the CHI injector region. A CHI discharge is generated by driving current, using an external power supply, along magnetic field lines that connect the inner and outer divertor plates in the CHI injector region. The CHI plasma evolution and closed flux formation on QUEST are very similar to those on NSTX and have generated toroidal currents of 150 kA with 100 kA of current flowing on closed flux surfaces. An alternate, force-free model approach has been used to derive the CHI scaling relations. The resulting CHI scaling relations from the model are consistent with the conventional CHI scaling relations, which state that the CHI generated toroidal current is proportional to the CHI injector flux and the CHI injector current is inversely proportional to the toroidal field. These results from QUEST bode well for the application of CHI in a new generation of compact high field STs and low aspect ratio tokamaks in which the space for the central solenoid is very restricted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Design, construction, and testing of no-insulation small subscale solenoids for compact tokamaks

Fusion energy systems studies (FESS) for next-step devices based on the most promising magnetic configurations indicate that high magnetic fields and high current density for magnet coil systems may reduce device size and lower the cost. High current density and radiation resistant fusion magnets are particularly beneficial for low cost, low aspect ratio compact reactor designs such as Fusion Nuclear Science Facility (FNSF), Fusion Pilot Plant (FPP) of low-aspect ratio spherical tokamak (ST) or compact stellarators. Unlike typical high field magnets for nuclear magnetic resonance (NMR), magnetic resonance imaging (MRI), or high energy physics research applications, neutron irradiation damage to organic insulations in the coil winding pack is a critical issue for next generation fusion reactors where orders of magnitude higher neutron fluence than those in present experimental reactors such as ITER are expected. Moreover, a high coil winding pack current density is needed for high field magnets in low cost, compact radial build next step fusion reactors. The slow current charging time, however, is an issue in fully non-insulated coils. In this work, we present the design, construction and testing of subscale Nb3Sn solenoids, up to half the diameter of the central solenoid (CS) for National Spherical Torus Experiment (NSTX), with and without inter-layer insulation for enhancing radiation resistance while improving the winding pack current density and coil performance. The major radius for the NSTX/NSTX-Upgrade (reference for compact ST) is 0.854/0.934 meter, and 4.8 meters for FNSF. The magnetic field for NSTX/NSTX-U at the plasma center is 0.6/1 Tesla and 9 Tesla for FNSF. The inner diameter of the central solenoid coil is 0.2/0.4 meter for NSTX/NSTX-U and 1.2 meters for FNSF. The current charging and discharging behavior of the prototype solenoids was investigated to quantify performance advantages of a simplified coil fabrication without error-prone vacuum pressure impregnation (VPI) for the removal of epoxy organic insulation. Scalability of the no insulation concept for fusion can be addressed via engineered coating for novel insulation on contact resistance or intra-layer no insulations. Radiation resistance and coil winding efficiency were significantly improved in the no insulation coils for next step compact fusion reactors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Design of 3D Oxide–Metal Hybrid Metamaterial for Tailorable Light–Matter Interactions in Visible and Near-Infrared Region

Dielectric–metallic hybrid metamaterials exhibit extraordinary optical properties due to the light–matter interactions at the dielectric–metallic interfaces. The ability in precision control of the light–matter interactions in nanoscale is key to tailor the optical properties of hybrid metamaterials. In this work, a complex 3D framework of multilayered self-assembled BaTiO 3 (BTO)-Au hybrid thin films is demonstrated with such precision control of the light–matter interaction in nanoscale. Here, unique “bamboo-like” Au nanostructures are formed via the bilayer and trilayer stacking of BTO-Au hybrid layers with interlayers of SrTiO 3 , CeO 2 , or MgO. Different film strain states introduced by the three interlayers result in variable diameter and density of Au nanopillars. Both simulated and experimental optical data demonstrate the localized surface plasmon resonance change and hyperbolic dispersion wavelength shift in visible to near-infrared because of the effective tuning of the Au nanopillar aspect ratio and free electron density. The highly tunable optical properties along with the ferroelectric behavior and thermal robustness of the 3D hybrid film enable it to be a great candidate for multifunctional applications. This study demonstrates a unique 3D approach for precision optical property tuning and combined functionalities in oxide–metal metamaterial systems toward future integrated photonic and electronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Predictable third harmonic generation in GaAs metasurfaces through group theory inverse design of meta-atoms

Here we report the group theory-based inverse design of meta-atoms for a dielectric metasurface in GaAs with predictable optical linear response and third harmonic generation (THG). Six sharp Fano resonances have been observed with a corresponding polarization dependence as predicted by group theory and the meta-atom’s symmetry in the D2h point group. THG has been observed for two modes under x-polarization excitation and one mode for y-polarization, in agreement with theoretical symmetry predictions. The polarization-dependent THG aspect ratio was observed to reach as high as 108. Through strategic structural or symmetry-preserving perturbations, it was shown that the THG can be enhanced or reduced by a factor of 7. The highest THG conversion efficiency was estimated to be 3.1×10-7 at the pump intensity of 1.51 MW/cm2. This high THG conversion efficiency indicates that our group theory approach to modal engineering opens a new path towards optical nonlinearity tuning in dielectric metasurfaces.

Aoueille, Andrew↗
DOE OSTI2022

Mass Transport Limitations and Kinetic Consequences of Corn Stover Deacetylation

Alkaline pretreatment of herbaceous feedstocks such as corn stover prior to mechanical refining and enzymatic saccharification improves downstream sugar yields by removing acetyl moieties from hemicellulose. However, the relationship between transport phenomena and deacetylation kinetics is virtually unknown for such feedstocks and this pretreatment process. Here, we report the development of an experimentally validated reaction–diffusion model for the deacetylation of corn stover. A tissue-specific transport model is used to estimate transport-independent kinetic rate constants for the reactive extraction of acetate, hemicellulose and lignin from corn stover under representative alkaline conditions (5–7 g L -1 NaOH, 10 wt% solids loadings) and at low to mild temperatures (4–70°C) selected to attenuate individual component extraction rates under differential kinetic regimes. The underlying transport model is based on microstructural characteristics of corn stover derived from statistically meaningful geometric particle and pore measurements. These physical descriptors are incorporated into distinct particle models of the three major anatomical fractions (cobs, husks and stalks) alongside an unsorted, aggregate corn stover particle, capturing average Feret lengths of 917–1239 μm and length-to-width aspect ratios of 1.8–2.9 for this highly heterogeneous feedstock. Individual reaction–diffusion models and their resulting particle model ensembles are used to validate and predict anatomically-specific and bulk feedstock performance under kinetic-controlled vs. diffusion-controlled regimes. In general, deacetylation kinetics and mass transfer processes are predicted to compete on similar time and length scales, emphasizing the significance of intraparticle transport phenomena. Critically, we predict that typical corn stover particles as small as ~2.3 mm in length are entirely diffusion-limited for acetate extraction, with experimental effectiveness factors calculated to be 0.50 for such processes. Debilitatingly low effectiveness factors of 0.021–0.054 are uncovered for cobs—implying that intraparticle mass transfer resistances may impair observable kinetic measurements of this anatomical fraction by up to 98%. These first-reported quantitative maps of reaction vs. diffusion control link fundamental insights into corn stover anatomy, biopolymer composition, practical size reduction thresholds and their kinetic consequences. These results offer a guidepost for industrial deacetylation reactor design, scale-up and feedstock selection, further establishing deacetylation as a viable biorefinery pretreatment for the conversion of lignocellulosics into value-added fuels and chemicals.

09 BIOMASS FUELS↗
DOE OSTI2024

Kinetic-ballooning-bifurcation in tokamak pedestals across shaping and aspect-ratio

We use a new gyrokinetic threshold model to predict a bifurcation in tokamak pedestal width-height scalings that depends strongly on plasma shaping and aspect-ratio. The bifurcation arises from the first and second stability properties of kinetic-ballooning-modes that yields wide and narrow pedestal branches, expanding the space of accessible pedestal widths and heights. The wide branch offers potential for edge-localized-mode-free pedestals with high core pressure. For negative triangularity, low-aspect-ratio configurations are predicted to give steeper pedestals than conventional-aspect-ratio. Both wide and narrow branches have been attained in tokamak experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

In-situ relative calibration of Bragg crystals with Monte Carlo line ratio analysis

X-ray line emission spectra can thoroughly characterize hot plasmas, especially when line shapes and ratios convey distinct aspects of plasma conditions. However, the high spectral resolution required for observing line shapes is often at odds with the large bandwidth required to observe many line ratios across a wide spectral range. One strategy to obtain high spectral resolution over a wide bandwidth is to use multiple crystals with calibrated reflectivity so that line intensities across different crystals can be compared. Here, we explore the use of a low-resolution, wide-bandwidth mica survey spectrometer to infer relative reflectivity of two high-resolution, narrow-bandwidth quartz crystals. Finally, a Monte Carlo error analysis determines comparable x-ray line ratios measured from both spectrometers, resulting in an in situ calibration factor and associated uncertainty for the relative reflectivity of the high-resolution crystals.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Monitoring steel fibre orientation in self-compacting cementitious composite slabs during pouring with dynamic X-ray radiography

This paper presents a new technique based on dynamic X-ray radiography that can be used to assess fibre orientation during pouring of steel fibre reinforced cementitious composites. Synthetic examples were used to assess the suitability and robustness of the technique, which was shown to provide reliable measurements of fibre orientation even when the signal-to-noise ratio is relatively high. A study was then carried out on the effect of formwork aspect ratio, time/duration of pouring, and rebar placement on the fibre orientation while pouring self-compacting cementitious composite slabs. Results demonstrated the ability of the technique in monitoring the movements of fibres while pouring, and the strong effect of the flow in inducing preferential fibre alignment within the slabs. Fibre orientation was found to vary progressively over time and could take about half of the duration of pouring to fully stabilise.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Asymptotic quasisymmetric high-beta three-dimensional magnetohydrodynamic equilibria near axisymmetry

Quasisymmetry (QS), a hidden symmetry of the magnetic field strength, is known to support nested flux surfaces and provide superior particle confinement in stellarators. In this work, we study the ideal magnetohydrodynamic (MHD) equilibrium and stability of high-beta plasma in a large-aspect-ratio stellarator. In particular, we show that the lowest-order description of a near-axisymmetric equilibrium vastly simplifies the problem of three-dimensional quasisymmetric MHD equilibria, which can be reduced to a standard elliptic Grad–Shafranov equation for the flux function. We show that any large-aspect-ratio tokamak, deformed periodically in the vertical direction, is a stellarator with approximate volumetric QS. We discuss exact analytical solutions and numerical benchmarks. Finally, we discuss the ideal ballooning and interchange stability of some of our equilibrium configurations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Molecular aspect ratio effect on axial thermal transport in solution-spun carbon nanotube fibers

Neat, densely packed, and highly aligned carbon nanotube fibers (CNTFs) have appealing room-temperature axial thermal conductivity (⁠k⁠) and thermal diffusivity (⁠α⁠) for applications in lightweight heat spreading, flexible thermal connections, and thermoelectric active cooling. Although CNTFs are regularly produced from different input carbon nanotubes (CNTs), prior work has not quantified how the CNT molecular aspect ratio r (i.e., molecular length-to-diameter ratio) influences k and in well-aligned, packed CNTFs. Here, we perform self-heated steady-state and three-omega thermal measurements at room temperature on CNTF suspended in vacuum. Our results show that k increases from 150 to 380 W / mK for viscosity-averaged molecular aspect ratios increasing from r = 960 to 5600 and nanotube diameters of ~2 nm, which we attribute to the effects of thermal resistances between CNT bundles. CNTFs made with varying volume fraction Φ of constituent high-r and low-r CNT have properties that fall within or below the typical macroscopic rule-of-mixtures bounds. The thermal diffusivity α scales with k, leading to a sample-averaged volumetric heat capacity of 1.5 ± 0.3 MJ / m 3 K⁠. This work's findings that fibers made from longer CNT have larger k and α at room temperature motivate further investigation into thermal transport in solution-spun CNTF.

42 ENGINEERING↗
DOE OSTI2024

Design of a Thomson scattering diagnostic for the SMall Aspect Ratio Tokamak (SMART)

Here, we describe the design of a Thomson scattering (TS) diagnostic to be used on the SMall Aspect Ratio Tokamak (SMART). SMART is a spherical tokamak being commissioned in Spain that aims to explore positive triangularity and negative triangularity plasma scenarios at a low aspect ratio. The SMART TS diagnostic is designed to operate at high spatial resolution, 6 mm scattering length in the low-field side and 9 mm in the high-field side regions, and a wide dynamic range, electron temperature from 1 eV to 1 keV and density from 5 x 10 18 m -3 to 1 x 10 20 m -3 ⁠, to resolve large gradients formed at the plasma edge and in the scrape-off layer (SOL) under different triangularities and low aspect ratios. A 2 J @1064 nm laser will be used that is capable of operating in the burst mode at 1, 2, and 4 kHz to investigate fast phenomena and at 30 Hz to study 1 s (or more) long discharges. The scattered light will be collected over an angular range of 60° – 120° from 28 spatial points in the midplane covering the entire plasma width and the outer midplane SOL. Each scattering signal will be spectrally resolved on five wavelength channels of a polychromator to obtain the electron temperature measurement. We will also present a method to monitor in situ laser alignment in the core during calibrations and plasma operations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Overview of the MAST Upgrade physics programme: testing novel concepts at low aspect ratio to inform future devices

The research programme performed on the Mega Amp Spherical Tokamak (MAST) Upgrade experiment has made significant advances in developing the physics understanding of low aspect ratio tokamaks in support of the operation of ITER and design of fusion powerplants. High performance plasma scenarios have been developed to facilitate a broad programme of experiments, in which confinement is constrained by the presence of m/n = 2/1 modes that cause substantial losses of fast ions. The onset of these modes coincides with the q = 2 surface residing in a local minimum in the toroidal current density profile. The maximum electron temperature at the pedestal top, T e,ped is limited with gas fuelling to ∼350 eV to maintain regular ELMs; higher T e,ped results in a transition to a non-stationary ELM-free regime. The operational space of spherical tokamaks has been expanded into small and ELM-free regimes. Strong shaping of the last closed flux surface can induce a transition from large to small ELMs, and ELM suppression with resonant magnetic perturbations has been observed for the first time in a low aspect ratio tokamak. Negative triangularity shaping has induced a transition from ELMy H-mode to a high-performance L-mode regime for the first time in a low aspect ratio tokamak. In studies of fast ion confinement, losses of fast particles due to Global Alfvén Eigenmodes have been identified. Interactions between fast ions generated by off-axis neutral beam injection and thermal neutrals can result in significant losses of fast ions. Experiments with on- and off-axis neutral beam injection exhibit a flux pumping mechanism, where the central safety factor is held to ∼1 in the absence of sawteeth. In studies of pedestal physics, it has been found that elevated main chamber neutral pressures result in an increase in the electron density and reduction in the temperature at the pedestal top. Advances in understanding plasma exhaust include the integration of a high-performance plasma core with detached outer divertors in the X-point target configuration. A newly commissioned lower divertor cryopump reduces the lower divertor neutral pressure by up to 50%, with minimal effect on the main chamber or upper divertor. New measurements and SOLPS-ITER simulations emphasise the importance of plasma–neutral interactions on divertor detachment in the conditions accessible in experiments. Real-time control of the ionisation front location in both divertor chambers independently has been demonstrated in double null experiments, enabled by the tightly baffled divertor chambers.

MAST Upgrade↗
DOE OSTI2021

Atmospheric Transport of North African Dust-Bearing Supermicron Freshwater Diatoms to South America: Implications for Iron Transport to the Equatorial North Atlantic Ocean

The equatorial North Atlantic Ocean (NAO) is a nutrient-limited ecosystem that relies on the deposition of long-range transported iron (Fe)-containing aerosols to stimulate primary productivity. Using microscopy, we characterized supermicron and supercoarse mode African aerosols transported to the western NAO in boreal winter/spring. In this work, we detected three particle types including African dust, primary biological aerosol particles, and freshwater diatoms (FDs). FDs contained 4% Fe by weight due to surficial dust inclusions that may be susceptible to chemical processing and dissolution. FDs were typically larger than dust particles and comprised 38% of particles between 10 and 18 μm in diameter. The low density, high surface-area-to-volume ratio, and large aspect ratios of FD particles suggest a mechanism by which they can be carried great distances aloft. These same properties likely increase the residence time of FDs in surface waters thereby increasing the time for Fe dissolution and their potential impact on marine biogeochemical cycles.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Current ramp-up studies for NSTX-U in support of the development of non-inductive current ramp-up scenarios in STs

The Spherical Tokamak (ST) is a low-aspect-ratio tokamak projected to enable simultaneous operation at high normalized toroidal beta and high bootstrap current fraction. However, a compact ST reactor cannot be built with a full-sized solenoid. The remaining current required for sustained operation must be ramped up non-inductively. Sustained 100% non-inductive current drive at the MA level has not yet been demonstrated on an ST. Non-inductive current ramp-up is therefore a more challenging objective that the NSTX-U research program aims to address. In support of this development, free-boundary TRANSP simulations have been used to develop a current ramp-up scenario in which a significant fraction of the current is driven non-inductively by a combination of neutral-beam and bootstrap current drive. The resulting discharge has properties favorable for non-inductive current drive, such as a low normalized internal plasma inductance of approximately 0.45, a minimum safety factor exceeding 2, and a slightly reversed-shear q-profile. In these discharges, the plasma current ramps to 900 kA within 250 ms in an L-mode configuration, with varying electron density and density profiles. These discharges should be suitable for next-step NSTX-U experiments aimed at generating a robust L-mode fiducial scenario with low central solenoid flux consumption, which could be progressively improved as new NSTX-U experimental discharges are developed.

Raman, Roger [Univ. of Washington, Seattle, WA (Un↗