Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hydrogen storage materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Techno-Economic Analysis of a Cryogenic Flux Capacitor for Grid Storage

Abstract The Cryogenic Flux Capacitor (CFC) is a cold, dense fluid storage core with integrated design features that afford the designer flexibility and provide new possibilities for the storage and discharge of energy. The stored energy, in this case, is represented by hydrogen physically bonded within the nanoscale pores within the aerogel composite blanket material, and the process of bonding or debonding is governed by principles of physical adsorption (physisorption) and thermodynamics. The large surface area afforded by the nanoporous aerogel (∼1,000 m2/g) allows for storage densities close to, or in some cases exceeding, that of normal boiling point liquids. Its performance easily exceeds what can be achieved via ambient temperature, high-pressure gas storage for an equivalent volume. CFC storage is predicted to be easily scalable, is constructed from readily available commercial materials, lends itself to a range of pressure applications, and is geometry insensitive. The high energy density of CFC-stored hydrogen allows long durations of storage, such as daily to monthly cycling, which corresponds to approximately 10 to 100 hours of duration, respectively. The techno-economic analysis examines different types of hydrogen storage for commercial viability. The assessment includes the use of hydrogen blended with natural gas in a combined cycle gas turbine. The study provides results for a range of blends from 100% natural gas to 100% hydrogen. The required fuel usages are estimated for the intended application in a grid scenario that features large amounts of renewable penetration, 10 hours, and as a baseload, 100 hours. The study presents preliminary estimates of the capital cost of storage and operating cost of storage. In addition, the cost of firing natural gas and capturing the carbon dioxide (CO2) in a carbon capture and sequestration (CCS) system is assessed. Based on the study, it is shown that CFC can competitively meet performance and cost needs for grid-based energy storage.

08 HYDROGEN↗
DOE OSTI2021

Assessment of Performance of Density Functionals for Predicting Potential Energy Curves in Hydrogen Storage Applications

We report the availability of accurate computational tools for modeling and simulation is vital to accelerate the discovery of materials capable of storing hydrogen (H 2 ) under given parameters of pressure swing and temperature. Previously, we compiled the H2Bind275 data set consisting of equilibrium geometries and assessed the performance of 55 density functionals over this data set (Veccham, S. P.; Head-Gordon, M. J. Chem. Theory Comput. 2020, 16, 4963-4982). As it is crucial for computational tools to accurately model the entire potential energy curve (PEC), in addition to the equilibrium geometry, we extended this data set with 389 new data points to include two compressed and three elongated geometries along 78 PECs for H 2 binding, forming the H2Bind78 × 7 data set. By assessing the performance of 55 density functionals on this significantly larger and more comprehensive H2Bind78 × 7 data set, we identified the best performing density functionals for H 2 binding applications: PBE0-DH, ωB97X-V, ωB97M-V, and DSD-PBEPBE-D3(BJ). The addition of Hartree-Fock exchange improves the performance of density functionals, albeit not uniformly throughout the PEC. We recommend the usage of ωB97X-V and ωB97M-V density functionals as they offer good performance for both geometries and energies. In addition, we also identified B97M-V and B97M-rV as the best semilocal density functionals for predicting H 2 binding energy at its equilibrium geometry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Thermomechanical Properties of Hafnium Hydride for Radiation Shielding in Tokamak Devices

The development of effective neutron shielding materials is of paramount importance for the progression of fusion technologies with the aim of producing clean and sustainable energy for future generations. This study demonstrates the successful fabrication of a promising candidate material for shielding applications, hafnium hydride, through the powder metallurgy process. Powder metallurgy fabrication resulted in the production of 91% dense, crack-free, ε-phase HfH 2 pellets with a hydrogen-to-metal ratio of 1.89 to 2.00. Resonant ultrasound spectroscopy (RUS) was used to measure a Young’s modulus of 34.52 ± 2.70 GPa and a shear modulus of 12.25 ± 0.18 GPa. Nanoindentation techniques have been used to establish a hardness value of 4.45 ± 1.63 GPa, and a Young’s modulus of 47.8 ± 6.4 GPa was determined using Poison’s ratio from RUS. Hydrogen release was measured using thermogravimetric analysis and appeared to occur in three different regimes as the sample transitioned through the ε- and δ-phases. Heat capacity matched literature data up to 600 K, after which a rapid increase was observed due to phase transformations occurring with hydrogen loss.

Hafnium hydride↗
DOE OSTI2021

An Ultrastable Aqueous Iodine-Hydrogen Gas Battery

Rechargeable hydrogen gas batteries are highly desirable for large-scale energy storage because of their long life cycle, high round trip efficiency, fast reaction kinetics, and hydrogen gas profusion. Coupling advanced cathode chemistries with hydrogen gas anode is an emerging and exciting area of research. Here, a novel high-performance aqueous iodine-hydrogen gas (I 2 -H 2 ) battery using iodine as cathode and hydrogen gas as the electrocatalytic anode in environmentally benign aqueous electrolytes is reported. The working chemistry of the battery involves I 2 /I - solid-liquid reactions occurring over the cathode along with H 2 /H 2 O gas-liquid reactions at the anode, achieving a high rate performance of 100 C and long-lasting stability of over 60 000 cycles. Additionally, the static aqueous I 2 -H 2 battery displays a volumetric capacity of 15.5 Ah L -1 along with good self-healing capability towards cell overcharge. The current battery design exhibits robust electrochemical performance irrespective of acidic, neutral, and alkaline electrolyte systems. This study paves the way towards the industrialization of economically effective, high-power density, and long-term I 2 -H 2 batteries for large-scale energy storage applications.

08 HYDROGEN↗
DOE OSTI2022

Integration of a high oxygen permeability ionomer into polymer electrolyte membrane fuel cell cathodes for high efficiency and power density

In this work, we present a study on the integration of a high oxygen permeability ionomer (HOPI) with high durability carbon supported platinum (Pt/C) catalysts to prepare cathode catalyst layers (CCLs) for polymer electrolyte membrane fuel cells (PEMFCs). A key motivation is the production of PEMFCs with high efficiency and durability for heavy-duty fuel cell vehicles. Our results from integrating a pre-commercial HOPI with robust, state-of-the-art catalysts with medium and low surface area carbon supports show significant increases in specific activities (67% increase over the standard commercial ionomer) at low current densities and reduced oxygen (O 2 ) transport resistances (R O2 ’s) at high current densities, enabling both higher efficiency and peak power density. The reduction in the R O2 with the HOPI is most significant at low relative humidity (RH), due to its more rigid backbone structure resisting compaction at lower water contents. In our ink optimization analysis, we show that the HOPI in this study achieves its peak performance with an ionomer to carbon ratio (I/C) of 0.6 and a moderately alcohol-rich ink solvent when fabricating catalyst layers by the decal method with an automatic wet film coater.

08 HYDROGEN↗
DOE OSTI2021

Chemomechanical effect of reduced graphene oxide encapsulation on hydrogen storage performance of Pd nanoparticles

Primary chemomechanical impacts of confinement on hydrogen storage performance are studied using a nanolaminate structure where reduced graphene oxide (rGO) encapsulates palladium (Pd) nanoparticles. Three contributing factors are identified that can alter the reaction enthalpy: nanosizing, chemical interaction with the encapsulant, and mechanical stress induced strain from a combination of clamping force and lateral pulling force exerted on the Pd nanoparticles. The mechanical contributions are quantified by combining transmission electron microscopy, ab initio computation, and continuum elasticity theory, from which the encapsulation is found to exert an additional strain of 4.96% and 2.99% before and after hydrogen absorption, respectively, increasing the Pd and Pd hydride (PdH x ) reaction enthalpy by 1.3–2.8 kJ (mol H 2 ) -1 . The effect of the chemical interaction with rGO also raises the reaction enthalpy by up to 1.6 kJ (mol H 2 ) -1 , while the nanosizing effect decreases the reaction enthalpy. The three contributing factors to the reaction enthalpy are found to be similar in magnitude, where the net effect is in agreement with the measured enthalpy increase of 3.7 kJ (mol H 2 ) -1 from the bulk value. Hydrogen absorption kinetics and capacity also improved, which is attributed to facile nucleation of the hydrogen-rich phase enabled by the inhomogeneous strain distribution over the encapsulated PdHx nanoparticles. These results demonstrate that the chemomechanical effect can be controlled in the nanolaminate structure, providing an ideal template for tuning hydrogen storage performance.

08 HYDROGEN↗
DOE OSTI2024

Understanding electronic structure tunability by metal dopants for promoting MgB 2 hydrogenation

Hydrogen is a promising energy carrier, but its onboard application is limited by the need for compact, low-pressure storage solutions. Solid-state complex metal hydride systems, such as MgB 2 /Mg(BH 4 ) 2 , offer high storage capacities but suffer from sluggish kinetics and poor reversibility. One avenue for improving reactivity is to introduce metal dopants to alter electronic and atomic properties, but the role of these chemical additives remains poorly understood, particularly for the hydrogenation reaction. In this work, we used density functional theory calculations on model MgB 2 systems to rationalize the potential role of metal dopants in destabilizing B–B bonding within the MgB 2 lattice. We carried out detailed electronic structure analyses for 28 different metal dopant adatoms to identify properties that contribute to a dopant’s efficacy. Based on the simulation results, we propose that an intermediate ionic and covalent character of the bonds between adatoms and B atoms is desirable for facilitating charge redistribution, disrupting the B–B bond network, and promoting H 2 dissociation and H atom chemisorption on MgB 2 .

08 HYDROGEN↗
DOE OSTI2023

SPUTTERED THIN FILMS FOR VERY HIGH POWER, EFFICIENT, AND LOW-COST COMMERCIAL SOFCS

The aim of this project was to leverage the low area specific resistance (ASR) of Redox’s GDC electrolyte-based cell architecture and increase solid oxide fuel cell (SOFC) efficiency (i.e., open circuit voltage, or OCV) without significantly increasing cell resistance. The key to achieving the increased SOFC efficiency is the introduction of a thin sputtered yttria stabilized zirconia (YSZ) electron-blocking layer and a thin sputtered gadolinia doped ceria (GDC) barrier layer on top of the half-cell substrate (i.e., anode and GDC electrolyte). A key initial effort of the project was to improve the quality of the half-cell substrate surface so that any remaining defects were significantly smaller than the desired film thickness. During lab-scale trials, we had to overcome challenges with film cracking during post-sputtering treatments (e.g., thermal anneals) as well as damage to the sputtering targets. After the initial lab-scale trials, the focus shifted toward the use of commercial scale sputtering equipment with a sputtering equipment manufacturer in the microelectronics industry. Using the commercial sputtering equipment, we deposited films with different variations of power, PO2, sputtering time, platen speed, etc. We then determined the combinations of sputtering conditions and post-sputtering treatments that yielded high-quality films without cracks or other significant defects. While thin films were deposited on cells as large as 10 cm by 10 cm, the processing was optimized using 4 cm by 4 cm cells. Cell performance was evaluated in stainless-steel test fixtures between 500 °C and 700 °C with hydrogen fuel fed to the anode and air fed to the cathode. Extensive studies allowed us to determine that modified cathode and cathode contact firing processes were required to achieve theoretical OCV. Moreover, use of the new firing processes resulted in the need for a modified cathode contact to achieve a low ASR. In summary, the project demonstrated the performance of high OCV (1.13 V at 650 °C) from sputtered layers and a low ASR (~0.25 Ohms-cm2 at 650 °C) resulting from a modification of cathode/contact processing and the introduction of alternative contact layers that are sufficient to yield a Gen-1 cell with a maximum power density of approximately 1.2 W/cm2. At an operating voltage of 0.74 V, this would yield a cell power density of ~1.1 W/cm2. While not utilized in this project, a Redox Gen-2 cell has a catalyst-infiltrated porous anode that reduces the ASR by more than 50% from that of the Gen-1 cells used in this project. Therefore, if the sputtered YSZ electron-blocking layer and GDC barrier layer are added to a Gen-2 half cell with a similar increase in OCV to the theoretical value of ~1.13 V at 650 °C, and if the same improvement in ASR (from that demonstrated in this project) is achieved when using the Gen-2 half-cell architecture as a sputtered cell substrate, then the power density at 0.74 Vop could be as high as ~2.6 W/cm2. The impact of such power density gains, while still maintaining high cell efficiency, and thus high system efficiency, is a dramatic decrease in system cost because the stack represents ~30-40% of the SOFC system cost.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Reticular Chemistry for Highly Porous Metal–Organic Frameworks: The Chemistry and Applications

Current global crises related to clean energy and the environment entail the development of materials that are capable of addressing these challenges. Metal–organic frameworks (MOFs), a class of functional materials assembled from metal-containing nodes and organic ligands via coordination bonds, have been successfully developed for various applications, including catalysis, toxic chemical removal, and gas storage and separation, as a result of their highly tailorable nature and precisely engineered pore structures. In particular, the exceptionally high surface areas and porosities of MOFs are two of their most attractive characteristics and place them among the best porous materials for the storage of clean energy gases, such as hydrogen and methane. Reticular chemistry stands out as a prominent approach to the design of MOFs as this strategy allows for the rational top-down design of frameworks guided by topological nets to afford extended framework structures with precise architectural arrangements at the molecular level. Furthermore, bridging the gap between reticular chemistry design strategies and highly porous MOFs can facilitate the development of next-generation high-performance materials through state-of-the-art chemical design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Relative humidity threshold for oxygen generation by high-purity plutonium dioxides in 3013 containers

High-purity plutonium dioxide with adsorbed water in a sealed container can generate oxygen, but oxygen will not be generated in low water loading conditions. A threshold for oxygen generation has been observed in the hydrogen generation rate normalized by the specific power for high-purity plutonium dioxide. Normalized hydrogen generation rates above this threshold generate oxygen and below the threshold consume oxygen. The threshold rate is determined by the amount of water adsorbed onto the surface of the oxide. The relative humidity of the atmosphere that the oxide is in equilibrium with determines the amount of physisorbed water adsorbed on the surface. We calculate the relative humidity corresponding to the threshold rate as a function of mass and specific surface area of material stored in 3013 containers. Exceeding the calculated relative humidity may result in flammable gas mixtures of hydrogen and oxygen at some time during storage.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

High hydrogen coverage on graphene via low temperature plasma with applied magnetic field

The chemical functionalization of two-dimensional materials is an effective method for tailoring their chemical and electronic properties with encouraging applications in energy, catalysis, and electronics. One exemplary 2D material with remarkable properties, graphene, can be exploited for hydrogen storage and large on/off ratio devices by hydrogen termination. In this work, we describe a promising plasma-based method to provide high hydrogen coverage on graphene. A low pressure (~10 mtorr) discharge generates a fine-tunable low-temperature hydrogen-rich plasma in the applied radial electric and axial magnetic fields. Post-run characterization of these samples using Raman spectroscopy and X-ray photoelectron spectroscopy demonstrates a higher hydrogen coverage, 35.8%, than the previously reported results using plasmas. Plasma measurements indicate that with the applied magnetic field, the density of hydrogen atoms can be more than 10 times larger than the density without the magnetic field. With the applied electric field directed away from the graphene substrate, the flux of plasma ions towards this substrate and the ion energy are insufficient to cause measurable damage to the treated 2D material. As a result, the low damage allows a relatively long treatment time of the graphene samples that contributes to the high coverage obtained in these experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Ammonia eurefstics: Electrolytes for liquid energy storage and conversion at room temperature and ambient pressure

Herein we report the transformation of gaseous ammonia to a liquid at room temperature and ambient pressure through mixing with simple solid ammonium salts. The resulting liquids, named eurefstics, are potentially advantageous for the storage and electrochemical conversion of ammonia and the realization of a green ammonia energy economy. Physical properties of these eurefstics, including the temperature-dependent composition and composition-dependent densities, are reported to glean initial insight into the formation and behavior of this intriguing liquid. Preliminary electrochemical investigations of the eurefstics were also performed. We have found that these eurefstics formed are conductive and can be used directly as electrolytes for ammonia electrolysis reactions to produce hydrogen on demand. Open-circuit potential measurements were also made to determine the formal potential of the hydrogen evolution and corresponding overpotentials. Finally, safety concerns of the eurefstics are discussed in comparison with other liquid phase energy carriers.

25 ENERGY STORAGE↗
DOE OSTI2024

Hydrogen effects on the deformation and slip localization in a single crystal austenitic stainless steel

Hydrogen is known to embrittle austenitic stainless steels, which are widely used in high-pressure hydrogen storage and delivery systems, but the mechanisms that lead to such material degradation are still being elucidated. The current work investigates the deformation behavior of single crystal austenitic stainless steel 316L through combined uniaxial tensile testing, characterization and atomistic simulations. Thermally precharged hydrogen is shown to increase the critical resolved shear stress (CRSS) without previously reported deviations from Schmid’s law. Molecular dynamics simulations further expose the statistical nature of the hydrogen and vacancy contributions to the CRSS in the presence of alloying. Slip distribution quantification over large in-plane distances (> 1 mm), achieved via atomic force microscopy (AFM), highlights the role of hydrogen increasing the degree of slip localization in both single and multiple slip configurations. The most active slip bands accumulate significantly more deformation in hydrogen precharged specimens, with potential implications for damage nucleation. For $\langle$110$\rangle$ tensile loading, slip localization further enhances the activity of secondary slip, increases the density of geometrically necessary dislocations and leads to a distinct lattice rotation behavior compared to hydrogen-free specimens, as evidenced by electron backscatter diffraction (EBSD) maps. Finally, the results of this study provide a more comprehensive picture of the deformation aspect of hydrogen embrittlement in austenitic stainless steels.

36 MATERIALS SCIENCE↗