Search NASA⌕ Search

SEARCH · Search NASA

Results for “INORGANIC COATING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Cathode–Sulfide Solid Electrolyte Interfacial Instability: Challenges and Solutions

All-solid-state batteries are a candidate for next-generation energy-storage devices due to potential improvements in energy density and safety compared to current battery technologies. Due to their high ionic conductivity and potential scalability through slurry processing routes, sulfide solid-state electrolytes are promising to replace traditional liquid electrolytes and enable All-solid-state batteries, but stability of cathode-sulfide solid-state electrolytes interfaces requires further improvement. Herein we review common issues encountered at cathode-sulfide SE interfaces and strategies to alleviate these issues.

25 ENERGY STORAGE↗
NASA NTRS1961

Friction, Wear, and Evaporation Rates of Various Materials in Vacuum to 10(exp -7) mm Hg

The requirements for bearings and seals to operate in the environment of space dictate a new area for lubrication research. The low ambient pressures encountered in space can be expected to influence the behavior of oil, grease, and solid-film lubricants. The property of these materials most significantly affected by low ambient pressures is the evaporation rate. Various investigators have therefore measured the evaporation rates of oils and greases in vacuum as one method of establishing their relative merit for space applications (1-3). The results of this work have given some indication as to the oils and greases with the greatest stability at reduced ambient pressures. Only limited experimental work, however, has been reported in the literature for inorganic solids and soft metals which have potential use as solid lubricant films or coatings for hard alloy substrates [e.g. Reference ( 4 )]. In general, the evaporation rates of these materials would be lower than those of oils and greases. These films might therefore be very attractive as lubricants for high vacuum service.

Buckley, Donald H.↗
DOE OSTI2025

Toward Computation-Guided Design of Tunable Organic-Inorganic CdS Quantum Dot Binary Superlattices

Combining the advantages of structural programmability in sequence-defined biomimetic molecules and the controllable packing geometry in nanoparticle superlattices, we demonstrate a self-assembled organic-inorganic superlattice whose structure can be altered with the slightest change in the sequence of the organic counterpart. Here, oleate-coated CdS quantum dots (QDs) form a square-packed superlattice with a 1:1 molar equivalence of a di-block amphiphilic peptoid (Nbrpe6Dig) in chloroform. In contrast, no apparent structure is observed in the organic solvent alone. Based on theoretical evidence, we show that the assembly is a binary superlattice where both the CdS QDs and the peptoids serve as building blocks and further predict a correlation between the superlattice structure and the peptoid sequence. The computationally guided prediction is validated by experiments where superlattice transformation is observed with modified peptoids. The mechanism identified in our work inspires new ways to control and tune organic-inorganic hybrid nanomaterial self-assembly.

Qi, Xin↗
DOE OSTI2023

Enhanced CO 2 Reactive Capture and Conversion Using Aminothiolate Ligand–Metal Interface

Metallic catalyst modification by organic ligands is an emerging catalyst design in enhancing the activity and selectivity of electrocatalytic carbon dioxide (CO 2 ) reactive capture and reduction to value-added fuels. However, a lack of fundamental science on how these ligand–metal interfaces interact with CO 2 and key intermediates under working conditions has resulted in a trial-and-error approach for experimental designs. With the aid of density functional theory calculations, we provided a comprehensive mechanism study of CO 2 reduction to multicarbon products over aminothiolate-coated copper (Cu) catalysts. Our results indicate that the CO 2 reduction performance was closely related to the alkyl chain length, ligand coverage, ligand configuration, and Cu facet. The aminothiolate ligand–Cu interface significantly promoted initial CO 2 activation and lowered the activation barrier of carbon–carbon coupling through the organic (nitrogen (N)) and inorganic (Cu) interfacial active sites. Experimentally, the selectivity and partial current density of the multicarbon products over aminothiolate-coated Cu increased by 1.5-fold and 2-fold, respectively, as compared to the pristine Cu at –1.16 V RHE , consistent with our theoretical findings. Furthermore, this work highlights the promising strategy of designing the ligand–metal interface for CO 2 reactive capture and conversion to multicarbon products.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Extreme Antiscaling Performance of Slippery Omniphobic Covalently Attached Liquids

Scale formation presents an enormous cost to the global economy. Classical nucleation theory dictates that to reduce the heterogeneous nucleation of scale, the surface should have low surface energy and be as smooth as possible. Past approaches have focused on lowering surface energy via the use of hydrophobic coatings and have created atomically smooth interfaces to eliminate nucleation sites, or both, via the infusion of low-surface-energy lubricants into rough superhydrophobic substrates. Although lubricant-based surfaces are promising candidates for antiscaling, lubricant drainage inhibits their utilization. Here, we develop methodologies to deposit slippery omniphobic covalently attached liquids (SOCAL) on arbitrary substrates. Similar to lubricant-based surfaces, SOCAL has ultralow roughness and surface energy, enabling low nucleation rates and eliminating the need to replenish the lubricant. To enable SOCAL coating on metals, we investigated the surface chemistry required to ensure high-quality functionalization as measured by ultralow contact angle hysteresis (<3°). Using a multilayer deposition approach, we first electrophoretically deposit (EPD) silicon dioxide (SiO 2 ) as an intermediate layer between the metallic substrate and SOCAL. The necessity of EPD SiO 2 is to smooth (<10 nm roughness) as well as to enable the proper surface chemistry for SOCAL bonding. To characterize antiscaling performance, we utilized calcium sulfate (CaSO 4 ) scale tests, showing a 20× reduction in scale deposition rate than untreated metallic substrates. Descaling tests revealed that SOCAL dramatically decreases scale adhesion, resulting in rapid removal of scale buildup. Furthermore, our work not only demonstrates a robust methodology for depositing antiscaling SOCAL coatings on metals but also develops design guidelines for the creation of antifouling coatings for alternate applications such as biofouling and high-temperature coking.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Cesium-Coated Halide Perovskites as a Photocathode Material: Modeling Insights

Photocathodes emit electrons when illuminated, a process utilized across many technologies. Cutting-edge applications require a set of operating conditions that are not met with current photocathode materials. Meanwhile, halide perovskites have been studied extensively and have shown a lot of promise for a wide variety of optoelectronic applications. Well-documented halide perovskite properties such as inexpensive growth techniques, improved carrier mobility, low trap density, and tunable direct band gaps make them promising candidates for next-generation photocathode materials. In this study, we use density functional theory to explore the possible application of pure inorganic perovskites (CsPbBr 3 and CsPbI 3 ) as photocathodes. It is determined that the addition of a Cs coating improved the performance by lowering the work function anywhere between 1.5 and 3 eV depending on the material, crystal surface, and surface coverage. A phenomenological model, modified from that developed by Gyftopoulos and Levine, is used to predict the reduction in work function with Cs coverage. The results of this work aim to guide the further experimental development of Cs-coated halide perovskites for photocathode materials.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Method for coating ultrafine particles, system for coating ultrafine particles

The invention provides a method for dispersing particles within a reaction field, the method comprising confining the particles to the reaction field using a standing wave. The invention also provides a system for coating particles, the system comprising a reaction zone; a means for producing fluidized particles within the reaction zone; a fluid to produce a standing wave within the reaction zone; and a means for introducing coating moieties to the reaction zone. The invention also provides a method for coating particles, the method comprising fluidizing the particles, subjecting the particles to a standing wave; and contacting the subjected particles with a coating moiety.

25 ENERGY STORAGE↗
DOE OSTI2023

Chemical Vapor Deposition of Zirconium Compounds: A Review

Coatings of zirconium compounds are used in a wide variety of fields, yet an understanding and descriptions of deposition mechanisms are scant in the public literature. The mechanisms of deposition for metallic zirconium, ZrC, ZrN, ZrO 2 , ZrB 2 , and zirconium silicides are discussed based on the direct vapor deposition research of those compounds where possible or compared to complementary titanium systems when direct research is lacking. Both inorganic and organometallic deposition systems are discussed. As a class of compounds, an understanding of the vapor deposition mechanisms can be significantly improved by investigations on metallic zirconium deposition by zirconium halides and hydrogen and by in situ analysis techniques such as Fourier-transform infrared (FTIR) spectroscopy or x-ray photoelectron spectroscopy (XPS).

organometallic↗
NASA NTRS1982

Space stable thermal control coatings

A specification quality zinc orthotitanate coating was developed. This silicate-bonded Zn2TiO4 coating is discussed. The effects of precursor chemistry, precursor mixing procedures, stoichiometry variations, and of different heat treatments on the physical and optical properties of Zn2TiO4 are investigated. Inorganic silicates are compared to organic silicone binder systems. The effects of pigment to binder ratio, water content, and of different curing procedures on the optical and physical properties of Zn2TiO4 potassium silicate coatings are also studied. Environmental tests were conducted to determine the UV vacuum stability of coatings for durations up to 5000 equivalent Sun hours.

Harada, Y.↗
DOE OSTI2026

Industrial deposition of wavelength-shifting films for liquid argon photon detection systems

The Deep Underground Neutrino Experiment (DUNE) Phase-II Far Detector is considering an approximately 2000 m 2 photon detection system to achieve a target mean light yield of 180 PE/MeV. Meeting this requirement demands scalable, cost-effective, and high-quality wavelength-shifter (WLS) coatings capable of converting 127 nm liquid-argon scintillation light into visible photons with controlled and reproducible optical performance. We report on the successful realization of an industrial physical vapor deposition (PVD) process forp-terphenyl (pTP) coatings, adapted from vacuum deposition techniques developed for OLED display manufacturing, to produce uniform WLS layers on large-area inorganic substrates, a task traditionally challenged by adhesion and uniformity issues at organic-inorganic interfaces. Surface characterization by profilometry and spectroscopic measurements demonstrates edge-region thickness variation below 10% and emission spectra consistent with high-quality pTP reference samples. The industrial process demonstrates reproducibility, scalability, and significantly reduced production time compared to laboratory-based methods, while maintaining optical characteristics consistent with established pTP reference samples. These results establish a viable pathway for mass production of high-performance pTP coatings for DUNE FD3 and future neutrino experiments, from a coating manufacturing and process standpoint. Detector-level performance validation, including quantitative VUV conversion efficiency measurements at 127 nm, is identified as future work.

47 OTHER INSTRUMENTATION↗
NASA NTRS2008

Non-Destructive Evaluation of Materials via Ultraviolet Spectroscopy

A document discusses the use of ultraviolet spectroscopy and imaging for the non-destructive evaluation of the degree of cure, aging, and other properties of resin-based composite materials. This method can be used in air, and is portable for field use. This method operates in reflectance, absorbance, and luminescence modes. The ultraviolet source is used to illuminate a composite surface of interest. In reflectance mode, the reflected response is acquired via the imaging system or via the spectrometer. The spectra are analyzed for organic compounds (conjugated organics) and inorganic compounds (semiconducting band-edge states; luminescing defect states such as silicates, used as adhesives for composite aerospace applications; and metal oxides commonly used as thermal coating paints on a wide range of spacecraft). The spectra are compared with a database for variation in conjugation, substitution, or length of molecule (in the case of organics) or band edge position (in the case of inorganics). This approach is useful in the understanding of material quality. It lacks the precision in defining the exact chemical structure that is found in other materials analysis techniques, but it is advantageous over methods such as nuclear magnetic resonance, infrared spectroscopy, and chromatography in that it can be used in the field to assess significant changes in chemical structure that may be linked to concerns associated with weaknesses or variations in structural integrity, without disassembly of or destruction to the structure of interest.

Pugel, Betsy↗
DOE OSTI2021

Nanocarrier-loaded block copolymer dual domain organogels

Loaded polymer gels are prevalent materials in the controlled release community and, fairly recently, have been formulated to include nanocarrier domains such as micelles and vesicles. One mechanism used to establish the solid-like characteristic of gels is block copolymer self-assembly, which can result in a system-spanning, physically-crosslinked network. Additionally, the combination of nanocarrier and crosslink domain presence offers gels with a rich nanoscale phase space capable of intricate macroscopic property tuning. The current manuscript provides an overview of nanocarrier-loaded block copolymer organogels wherein nanocarriers are reverse micelles formed by sodium dioctyl sulfosuccinate (AOT), the block copolymer is a styrenic ABA triblock copolymer, and the gel solvent is aliphatic mineral oil. This introductory overview starts by identifying the envelope in ternary phase space wherein nanocarrier-loaded block copolymer organogels form (2-49 wt% triblock copolymer and 8x10 -3 -1 wt% AOT). Next, a detailed nanostructural description of gels varying in AOT and triblock copolymer concentration is presented. The manuscript concludes with demonstration of AOT reverse micelle release and gel uniaxial tensile response for gels containing 0-1 wt% AOT and 5-40 wt% styrenic triblock copolymer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Protective coatings for lithium metal electrodes

Double-layered protective coatings for lithium metal electrodes, as well as methods of formation relating thereto, are provided. The negative electrode assembly includes an electroactive material layer including lithium metal and a protective dual-layered coating. The protective dual-layered coating includes a polymeric layer disposed on a surface of the electroactive material layer and an inorganic layer disposed on an exposed surface of the polymeric layer. The polymeric layer has an elastic modulus of greater than or equal to about 0.01 GPa to less than or equal to about 410 GPa. The inorganic layer has an elastic modulus of greater than or equal to about 10 GPa to less than or equal to about 1000 GPa.

Xiao, Xingcheng↗
DOE OSTI2021

Comparative performance of bio-based coatings formulated with cellulose, chitin, and chitosan nanomaterials suitable for fruit preservation

Sustainable nanomaterials (SNMs) from wood, sugarcane and crab shell were prepared and used to coat selected fruits. The properties of SNMs and selected fruits were characterized and strawberry was used as an example to test antifungal activity and freshness preservation of the SNMs. The SNMs with their nano-structured morphology form strong shear-thinning dispersions for easy spraying on fruit surfaces. The fruit surface free energy was influenced by its surface morphology, predominant surface wax components, and cutin monomers. The antifungal activity of SNMs was influenced by their surface functional groups and particle size (crystals vs fibers). The coblend of wood nanocrystals (WCNCs) and chitosan nanofiber (CSNFs) exhibited the best antifungal property, which was comparable with the performance of the fungicide thiabendazole (80 mg L -1 ). The weight loss and color change of the WCNC/CSNF coated strawberries decreased by nearly half compared with the control samples, showing coating effectiveness on preserving fruit freshness.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Facile synthesis of co-doped Carbon nanofibers for supercapacitor applications

Here, in this study, the synthesis and electrochemical performance of carbon nanofibers (CNFs) co-doped with aluminum (Al) and nitrogen (N) and decorated with zinc oxide (ZnO) nanoparticles are investigated. After electrospinning polyacrylonitrile (PAN) nanofibers, the nanofiber mats are coated with Al and ZnO precursors by the dip coating method and converted into carbon nanofibers by thermal treatments at 850 °C. Co-doping and nanoparticle decoration affect the efficacy of carbon nanofibers as supercapacitors. With a maximal specific capacitance of 206.28 Fg -1 , it is believed that our produced carbon nanofibers, which can effectively store the renewable energy resources required to meet the rising energy demand, offer superior electrochemical properties compared to traditional supercapacitor materials. The effective incorporation of Al, N, and ZnO into the CNF structure, in conjunction with enhanced electrochemical performance, represents a significant advancement in the development of functional carbon nanofibers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗