Search NASA⌕ Search

SEARCH · Search NASA

Results for “Isolated Rotor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Navier-Stokes simulations of tip vortices for fixed and rotating helicopter blades

Flowfield and tip vortex results are presented for a hovering rotor blade at subcritical and supercritical flow conditions for both nonlifting and lifting configurations. These results are calculated numerically by solving, in a time-accurate fashion, the unsteady thin layer Navier-Stokes equations written in rotor coordinates. The lifting calculations use an induced downwash correction, estimated from a free wake analysis, to the geometric angle of attack of the blades to account for the wake effect. Comparison of numerical results with the experimental data shows very good agreement for all cases considered. Alternate methods of calculating hovering rotor flowfield as steady state flowfield on isolated fixed-blade that have the same circulation distribution as that of rotor in hover are also explored.

Srinivasan, G. R.↗
NASA NTRS1984

Application of modern structural optimization to vibration reduction in rotorcraft

The helicopter rotor model consists of a four bladed hingeless rotor attached to a fuselage. The helicopter is assumed to be in trimmed forward flight. Each blade is assumed to have flap, lag, and torsional degrees of freedom. The fuselage degrees of freedom are not included in the analysis. Thus the aeroelastic stability and response analysis upon which this study is based is an isolated blade analysis. The helicopter rotor vibration reduction problem expressed as a general class of structural synthesis problems is given.

Friedmann, P. P.↗
NASA NTRS1996

A Comparison of Computed and Experimental Flowfields of the RAH-66 Helicopter

This paper compares and evaluates numerical and experimental flowfields of the RAH-66 Comanche helicopter. The numerical predictions were obtained by solving the Thin-Layer Navier-Stokes equations. The computations use actuator disks to investigate the main and tail rotor effects upon the fuselage flowfield. The wind tunnel experiment was performed in the 14 x 22 foot facility located at NASA Langley. A suite of flow conditions, rotor thrusts and fuselage-rotor-tail configurations were tested. In addition, the tunnel model and the computational geometry were based upon the same CAD definition. Computations were performed for an isolated fuselage configuration and for a rotor on configuration. Comparisons between the measured and computed surface pressures show areas of correlation and some discrepancies. Local areas of poor computational grid-quality and local areas of geometry differences account for the differences. These calculations demonstrate the use of advanced computational fluid dynamic methodologies towards a flight vehicle currently under development. It serves as an important verification for future computed results.

vanDam, C. P.↗
NASA NTRS1985

Evaluation of a load cell model for dynamic calibration of the rotor systems research aircraft

The Rotor Systems Research Aircraft uses load cells to isolate the rotor/transmission system from the fuselage. An analytical model of the relationship between applied rotor loads and the resulting load cell measurements is derived by applying a force-and-moment balance to the isolated rotor/transmission system. The model is then used to estimate the applied loads from measured load cell data, as obtained from a ground-based shake test. Using nominal design values for the parameters, the estimation errors, for the case of lateral forcing, were shown to be on the order of the sensor measurement noise in all but the roll axis. An unmodeled external load appears to be the source of the error in this axis.

Duval, R. W.↗
NASA NTRS1993

Rotary-wing aeroelasticity with application to VTOL vehicles

A concise assessment is presented of the state of the art in the field of rotary-wing aeroelasticity (RWE). The basic ingredients of RWE are reviewed, including structural modeling, unsteady aerodynamic modeling, formulation of the equations of motion, and solution methods. Results illustrating these methods are presented for isolated blades and coupled rotor-fuselage problems. The application of active controls to suppress aeromechanical and aeroelastic instabilities and to reduce vibration in rotorcraft is discussed. Structural optimization with aeroelastic constraints, gust response analysis of helicopters, and aeroelastic problems in special VTOL vehicles are briefly examined.

Friedmann, Peretz P.↗
NASA NTRS2023

Blade-Wake Interaction Noise for Small Hovering Rotors, Part I: Characterization Study

This work illustrates the use of artificial neural network modeling to study and characterize broadband blade-wake interaction noise from hovering small unmanned aerial systems rotors subject to varying airfoil geometries, rotor geometries, and operating conditions. Design of experiments was used to create input feature spaces, and a high-fidelity strategy was implemented at the discrete data points defined by the input feature spaces to design airfoils and rotor blades, predict the unsteady rotor aerodynamics and aeroacoustics, and isolate the blade-wake interaction noise from the acoustic broadband noise. A metric for the blade-wake interaction noise was developed, and the ANOPP2 Artificial Neural Network Tool was used to identify an optimal prediction model for the nonlinear relationship between the input features and the metric for blade-wake interaction noise. This optimal artificial neural network was then validated over training/test data and exhibited prediction accuracy over 91% for data previously unseen by the model. A sensitivity analysis was conducted, which showed that input features that directly modify the thrust coefficient had a dominant effect over blade-wake interaction noise. The optimal prediction model along with aerodynamic simulations were used to further study the effect of varying input features on blade-wake interaction noise, and three types of blade-wake interaction noise were identified

Christopher S. Thurman↗
NASA NTRS1985

Solution method for a hovering helicopter rotor using the Euler equations

A method for the calculation of the flow field of a helicopter rotor blade in hover is presented. The approach uses a finite volume solution of the three dimensional Euler equations for the blade near field. In the Euler solver the velocity field is decomposed into two parts. One is the induced velocity of the vortex wake extending below the blade, found from a free wake calculation procedure. The other part is the unknown additional velocity field of the rotor blade. This approach eliminates numerical diffusion of the rolled up wake vorticity due to truncation error and artificial viscosity. Also, the effects of the far wake are included in the limited computational domain. Solutions are presented for an isolated wing and a model helicopter rotor and compared to experiment.

Roberts, T. W.↗
NASA NTRS1973

V/STOL tilt rotor aircraft study. Volume 10: Performance and stability test of A 1-14.622 Froude scaled Boeing Vertol Model 222 tilt rotor aircraft (Phase 1)

Wind tunnel test data obtained from a 1/4.622 Froude scale Boeing Model 222 with a full span, two prop, tilt rotor, powered model in the Boeing V/STOL wind tunnel are reported. Data were taken in transition and cruise flight conditions and include performance, stability and control and blade loads information. The effects of the rotors, tail surfaces and airframe on the performance and stability are isolated as are the effects of the airframe on the rotors.

Mchugh, F. J.↗
NASA NTRSDate not supplied

Physics-Informed Broadband Noise Source Identification and Prediction of an Ideally Twisted Rotor

This work aims to provide a physics-based approach for the prediction and isolation of broadband noise emanating from different regions of an ideally twisted rotor. A preliminary prediction was conducted using a lattice-Boltzmann method–very-large-eddy simulation (LBM-VLES) implemented within the software suite, PowerFLOW. Regions of particular interest to broadband noise were investigated by calculating one-third octave sound pressure levels of the unsteady pressure fluctuations acting on the rotor. These regions were then treated as individual Ffowcs Williams and Hawkings (FW-H) surfaces and simulated for three run conditions at a finer spatial resolution to identify the broadband noise from these separate regions and isolate it from the total acoustic spectra. These predictions were then compared to experimentally acquired data and to semiempirical prediction methods to highlight the acoustic contributions of various broadband noise generation mechanisms as well as to exemplify and explain shortcomings in the semiempirical methodology.

Christopher S Thurman↗
NASA NTRS1979

Aircraft control by propeller cyclic blades

A theory is developed for aircraft control obtained from the propeller forces and moments generated by blade angle variation during a blade revolution. The propeller blade is pitched harmonically one cycle per propeller revolution which results in vehicle control forces and moments, termed cyclic-control. Using a power series respresentation of an arbitrary function of cyclic-blade angle, cyclic-control theory is developed which leads to exact solutions in terms of derivatives of steady-state thrust and power with respect to blade angle. An alternative solution, when the cyclic-blade angle function is limited to a sinusoidal cycle, is in terms of Bessel functions. An estimate of non-steady azimuth angle change or lag is presented. Cyclic-control analysis applied to the counter-rotating propeller shows that control forces or moments can be uniquely isolated from each other. Thus the dual rotor, in hovering mode, has propulsion without rotor tilt or moments, or, when in propeller mode at the tail of an air ship or submarine, vehicle control with no vehicle movement. Control isolation is also attainable from three or more propellers in-line.

Deyoung, J.↗
NASA NTRS1996

Aeropropulsion Technology (APT). Task 23 - Stator Seal Cavity Flow Investigation

The focus of NASA Contract NAS3-25950 Task 23 was to numerically investigate the flow through an axial compressor inner-banded stator seal cavity. The Allison/NASA developed ADPAC code was used to obtain all flow predictions. Flow through a labyrinth stator seal cavity of a high-speed compressor was modeled by coupling the cavity flow path and the main flow path of the compressor. A grid resolution study was performed to guarantee adequate grid spacing was used. Both unsteady rotor-stator-rotor interactions and steady-state isolated blade calculations were performed with and without the seal cavity present. A parameterized seal cavity study of the high-speed stator seal cavity collected a series of solutions for geometric variations. The parameter list included seal tooth gap, cavity depth, wheel speed, radial mismatch of hub flowpath, axial trench gap, hub corner treatments, and land edge treatments. Solution data presented includes radial and pitchwise distributions of flow variables and particle traces describing the flow character.

Heidegger, N. J.↗
NASA NTRS1997

An Experimental Investigation of Steady and Unsteady Flow Field in an Axial Flow Turbine

Measurements were made in a large scale single stage turbine facility. Within the nozzle passage measurements were made using a five hole probe, a two-component Laser Doppler Velocimeter (LDV), and a single sensor hot wire probe. These measurements showed weak secondary flows at midchord, and two secondary flow loss cores at the nozzle exit. The casing vortex loss core was the larger of the two. At the exit radial inward flow was found over the entire passage, and was more pronounced in the wake. Nozzle wake decay was found to be more rapid than for an isolated vane row due to the rotor's presence. The midspan rotor flow field was measured using a two-component LDV. Measurements were made from upstream of the rotor to a chord behind the rotor. The distortion of the nozzle wake as it passed through the rotor blade row was determined. The unsteadiness in the rotor flow field was determined. The decay of the rotor wake was also characterized.

Zaccaria, M.↗
NASA NTRS1997

Comparison of Full-Scale XV-15 Wind Tunnel and In-Flight Blade-Vortex Interaction Noise

An isolated full-scale XV-15 rotor was tested in helicopter mode in the NASA Ames 80 by 120-Foot Wind Tunnel. Extensive acoustic data were obtained to define the rotor operating condition for maximum blade-vortex interaction (BVI) noise. Additional data were obtained at operating conditions simulating flight up to 80 knots. An XV-15 aircraft was also tested under operating conditions corresponding to landing approaches for which BVI is expected to be a maximum. In-flight acoustic data were obtained using the YO-3A acoustic research aircraft. An attempt was made to closely match wind tunnel and flight test operating conditions. Details of the two tests are described and some representative acoustic results are presented. Comparisons are shown between the wind tunnel data and corresponding flight test data. Preliminary results indicate very good correlation of the BVI-related features. However, some differences between flight test and wind tunnel results exist away from the BVI event, thought to arise from differences in the two flow environments.

Kitaplioglu, Cahit↗
NASA NTRS2004

Computation of a Single Airfoil Gust Response and Gust-Cascade Interaction Using the CE/SE Method

The problems 1 and 2 in Category 3 are solved using the space-time conservation element and solution element (CE/SE) method. Problem 1 concerns the acoustic field generated by the interaction of a harmonic vertical gust with a single isolated airfoil. Problem 2 models rotor-stator interaction in a 2D cascade. Both problems involve complex geometries and flow physics including vortex shielding and acoustic radiation. An unstructured triangular mesh is used to solve both problems. For problem 2, the Giles approach is incorporated with the CE/SE method to handle non-equal pitches of the rotor and stator. Numerical solution of both near and far fields of problem 1 are presented and compared with a frequency-domain solver GUST3D and a time-domain high-order Discontinuous Spectra Element Method (DSEM) solutions. For problem 2, numerical solutions on the blade surface, inlet and outlet planes are presented.

Wang, Xiao-Yen↗
NASA NTRS2011

Numerical Investigation of Rotorcraft Fuselage Drag Reduction Using Active Flow Control

The effectiveness of unsteady zero-net-mass-flux jets for fuselage drag reduction was evaluated numerically on a generic rotorcraft fuselage in forward flight with a rotor. Previous efforts have shown significant fuselage drag reduction using flow control for an isolated fuselage by experiment and numerical simulation. This work will evaluate a flow control strategy, that was originally developed on an isolated fuselage, in a more relevant environment that includes the effects of a rotor. Evaluation of different slot heights and jet velocity ratios were performed. Direct comparisons between an isolated fuselage and rotor/fuselage simulations were made showing similar flow control performance at a -3deg fuselage angle-of-attack condition. However, this was not the case for a -5deg angle-of-attack condition where the performance between the isolated fuselage and rotor/fuselage were different. The fuselage flow control resulted in a 17% drag reduction for a peak C(sub mu) of 0.0069 in a forward flight simulation where mu = 0:35 and CT/sigma = 0:08. The CFD flow control results also predicted a favorable 22% reduction of the fuselage download at this same condition, which can have beneficial compounding effects on the overall performance of the vehicle. This numerical investigation was performed in order to provide guidance for a future 1/3 scale wind tunnel experiment to be performed at the NASA 14-by 22-Foot Subsonic Tunnel.

Allan, Brian G.↗
NASA NTRS1987

Main rotor broadband noise study in the DNW

An acoustics test of a 2/5 scale model BO-105 helicopter main rotor was conducted in the Duits-Nederlandse Windtunnel (DNW). A range of operating conditions was tested from hover to moderately high flight speeds for various climb and descent rates at different thrust settings. Diagnostic tests including rotor speed and blade geometry changes were made to better isolate and study particular broadband self noise sources. Acoustic data in the form of acoustic pressure time histories and power spectra are used to demonstrate the regions of importance of the different broadband noise sources and their sensitivity to operating conditions. To help interpret the data, comparisons are made to predictions of rotor broadband noise. The predictions are based on self noise data previously obtained from isolated airfoil sections and the use of the NASA ROTONET program to define rotor performance and to sum contributions of noise from individual blade segments. An important result herein is the identification and articulation of a previously unheralded rotor broadband noise source. This source is blade-turbulent wake interaction (BWI) noise which dominates the spectra in the mid-frequencies for off-peak blade-vortex interaction (BVI) noise flight conditions.

Brooks, Thomas F.↗
NASA NTRS1979

Design and development of a motion compensator for the RSRA main rotor control

The RSRA, an experimental helicopter, is equipped with an active isolation system that allows the transmission to move relative to the fuselage. The purpose of the motion compensator is to prevent these motions from introducing unwanted signals to the main rotor control. A motion compensator concept was developed that has six-degree-of-freedom capability. The mechanism was implemented on RSRA and its performance verified by ground and flight tests.

Jeffrey, P.↗
NASA NTRS1994

2-D and 3-D oscillating wing aerodynamics for a range of angles of attack including stall

A comprehensive experimental investigation of the pressure distribution over a semispan wing undergoing pitching motions representative of a helicopter rotor blade was conducted. Testing the wing in the nonrotating condition isolates the three-dimensional (3-D) blade aerodynamic and dynamic stall characteristics from the complications of the rotor blade environment. The test has generated a very complete, detailed, and accurate body of data. These data include static and dynamic pressure distributions, surface flow visualizations, two-dimensional (2-D) airfoil data from the same model and installation, and important supporting blockage and wall pressure distributions. This body of data is sufficiently comprehensive and accurate that it can be used for the validation of rotor blade aerodynamic models over a broad range of the important parameters including 3-D dynamic stall. This data report presents all the cycle-averaged lift, drag, and pitching moment coefficient data versus angle of attack obtained from the instantaneous pressure data for the 3-D wing and the 2-D airfoil. Also presented are examples of the following: cycle-to-cycle variations occurring for incipient or lightly stalled conditions; 3-D surface flow visualizations; supporting blockage and wall pressure distributions; and underlying detailed pressure results.

Piziali, R. A.↗