Tests of the Landing on Water of a Model of a High-speed Airplane - Langley Tank Model 229
Explore the source record for details and available documents.
King, Douglas A↗
SEARCH · Search NASA
Results for “LANDING SPEED”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The Boulton and Paul "Bugle" airplane : day bomber
The Bugle is a twin engine tractor biplane. It features two Jupiter engines and oleo-pneumatic landing gear. Its maximum speed is 120 MPH.
BOULTON AND PAUL BUGLE (BRIT )↗
A Near Perfect Spin Balance (Measurement in Chaos)
The stringent spin balance requirements arise from the predecessor of SSMIS, the SSMI. The SSMI sensor spinning portion weighed only 85 pounds and contained 7 channels of radiometric data. The Aerospace Corporation recommended to pass on the same requirements from the smaller SSMI to our larger SSMIS (with slight change for increased weight). The SSMIS spinning portion will weigh about 155 pounds and contain 24 channels of radiometeric data. The SSMIS, on orbit, spins a CCW direction at 31.6 RPM its own drive motor. The packaging of this SSMIS is unique, as it combines three sensor into one unit. This combination allows for concurrently reading data in one beam. The unit will have a polar orbit about 500 miles above the earths surface. One of the primary influences for our receipt of the follow-on contract for the next generation sensor, was the ability to package 24 channels of radiometeric data into about the some volume as its predecessor. The data from SSMIS will be used to measure the following: (1) Ocean surface wind speed, (2) Rain over land an ocean, (3) Cloud water over Ocean, (4) Soil moisture, (5) Ice Concentration, (6) Ice age, (7) Ice Edge and snow edge, (8) Water vapor over Ocean, (9) Surface type, (10) Snow water content, (11) Land surface Temperature, (12) Cloud amount over ocean.
Luntz, R. A.↗
Low-Speed Investigation of the Effects of Large Wing-Sideslip Angles on the Aerodynamic Characteristics of Two Arrow-Wing-Fuselage Arrangements
A wind-tunnel investigation has been made of two methods proposed to reduce the high sinking speeds and improve the landing characteristics of low-aspect-ratio hypersonic airplanes by placing the wing at large angles of sideslip to increase its effective aspect ratio. The models investigated had conical fuselages and arrow wings, with a leading-edge sweep-back of 77.4deg, an aspect ratio of 1.23, and a 4-percent-thick straight-wedge section. For one model, the wing was pivoted on the fuselage to angles of wing sideslip from 0 to 90deg. For the other model, the wing was fixed to the fuselage, and the wing and fuselage were yawed together to sideslip angles from 0 to 90deg. The investigation was made in the Langley 300-MPH 7- by 10-foot tunnel for an angle-of-attack range from -8 to above 28deg. Longitudinal stability and control through the use of horizontal tails with elevators was studied on the pivoted-wing configuration. The roll control for both configurations was studied with deflection of the apex portion of the wing about an axis along the wing center line. The use of flaps with the wing at large sideslip angles was also investigated.
Thomas G Gainer↗
Ditching Tests of a 1/9-Size Model of the Army P-38 Airplane in Langley Tank No. 2 and at the Outdoor Catapult
A dynamically similar model of the Army P-38 airplane was tested to determine the best way to land this airplane on the water and to determine its probable ditching performance. The tests consisted of ditching the model at various landing attitudes, flap settings, speeds, weights, and conditions of simulated damage. The model was ditched in calm water from the tank towing carriage and a few ditching were made in both calm and rough water at the outdoor catapult. The performance of the model was determined by making visual observations, by recording lengths of run and time histories of decelerations, and by taking motion pictures of the ditchings.
Jarvis, George A.↗
Engineered Surfaces for Mitigation of Insect Residue Adhesion
Maintenance of laminar flow under operational flight conditions is being investigated under NASA s Environmentally Responsible Aviation (ERA) Program. Among the challenges with natural laminar flow is the accretion of residues from insect impacts incurred during takeoff or landing. Depending on air speed, temperature, and wing structure, the critical residue height for laminar flow disruption can be as low as 4 microns near the leading edge. In this study, engineered surfaces designed to minimize insect residue adhesion were examined. The coatings studied included chemical compositions containing functional groups typically associated with abhesive (non-stick) surfaces. To reduce surface contact by liquids and enhance abhesion, the engineered surfaces consisted of these coatings doped with particulate additives to generate random surface topography, as well as coatings applied to laser ablated surfaces having precision patterned topographies. Performance evaluation of these surfaces included contact angle goniometry of pristine coatings and profilometry of surfaces after insect impacts were incurred in laboratory scale tests, wind tunnel tests and flight tests. The results illustrate the complexity of designing antifouling surfaces for effective insect contamination mitigation under dynamic conditions and suggest that superhydrophobic surfaces may not be the most effective solution for preventing insect contamination on aircraft wing leading edges.
Siochi, Emilie J.↗
Nano-ADEPT Aeroloads Wind Tunnel Test
Analysis completed since the test suggests that all test objectives were met– This claim will be verified in the coming weeks as the data is examined further– Final disposition of test objective success will be documented in a final reportsubmitted to NASA stakeholders (early August 2015)– Expect conference paper in early 2016• Data products and observations made during testing will be used to refinecomputational models of Nano-ADEPT• Carbon fabric relaxed from its pre-test state during the test– System-level tolerance for relaxation will be driven by destination-specific andmission-specific aerothermal and aerodynamic requirements• Bonus experiment of asymmetric shape demonstrates that an asymmetricdeployable blunt body can be used to generate measureable lift– With a strut actuation system and a robust GN&C algorithm, this effect could beused to steer a blunt body at hypersonic speeds to aid precision landing
atmospheric entry↗
Computational and Experimental Fluid-Structure Interaction Analysis of a High-Lift Wing with a Slat-Cove Filler for Noise Reduction
Airframe noise is a significant component of overall noise produced by transport aircraft during landing and approach (low speed maneuvers). A significant source for this noise is the cove of the leading-edge slat. The slat-cove filler (SCF) has been shown to be effective at mitigating slat noise. The objective of this work is to understand the fluid-structure interaction (FSI) behavior of a superelastic shape memory alloy (SMA) SCF in flow using both computational and physical models of a high-lift wing. Initial understanding of flow around the SCF and wing is obtained using computational fluid dynamics (CFD) analysis at various angles of attack. A framework compatible with an SMA constitutive model (implemented as a user material subroutine) is used to perform FSI analysis for multiple flow and configuration cases. A scaled physical model of the high-lift wing is constructed and tested in the Texas A&M 3 ft-by-4-foot wind tunnel. Initial validation of both CFD and FSI analysis is conducted by comparing lift, drag and pressure distributions with experimental results.
Scholten, William D.↗
An Overview of NASA's Low Boom Flight Demonstration
NASA will soon begin a series of tests that will collect nationally representative data on how people perceive low noise supersonic overflights. For half a century, civilian aircraft have been required to fly slower than the speed of sound over land to prevent “creating an unacceptable situation” on the ground due to sonic booms. However, new aircraft shaping techniques have led to dramatic changes in how shockwaves from supersonic flight merge together as they travel to the ground. What used to sound like a boom on the ground will be transformed into a thump. NASA is now building a full-scale, piloted demonstration aircraft called the X-59 to demonstrate low noise supersonic flight. In 2024, the X-59 aircraft will commence a national series of community overflight tests to collect data on how people perceive “sonic thumps.” The community response data will be provided to national and international noise regulators as they consider creating new standards that allow supersonic flight over land at acceptably low noise levels.
Sonic Boom↗
Statistical Engineering Toward Commercial Supersonic Flight: NASA's Quesst Mission
NASA’s Quesst Mission has dual goals of demonstrating low-noise supersonic technology in flight and surveying public reactions to low-noise supersonic overflight. For half a century, commercial aircraft have been required to fly slower than the speed of sound over land to prevent “creating an unacceptable situation” on the ground due to sonic booms. However, aircraft shaping techniques honed through decades of research have dramatically changed the way shockwaves from supersonic flight merge together as they travel to the ground. What used to sound like a boom on the ground will be transformed into a thump. NASA is now building a full-scale, piloted demonstration aircraft called the X-59 to demonstrate low-noise supersonic flight. In 2024, the X-59 aircraft will commence a national series of community overflight surveys to collect data on how people perceive “sonic thumps.” The results will be provided to national and international noise regulators as they consider creating new standards that allow commercial supersonic flight over land at acceptably low noise levels. In this presentation we provide historical context for the current prohibitions on supersonic commercial flight. Using data collected during earlier NASA tests, we demonstrate how generalized linear mixed models can be used to inform the functional dose-response curve. We also illustrate simulation experiments of the variability of sonic thump exposure across the United States. Finally, we discuss some of the challenges in designing the future community studies and generalizing them to a nationally-representative dose-response curve.
Quesst↗
Operational Concept for Flight Crews to Participate in Merging and Spacing of Aircraft
The predicted tripling of air traffic within the next 15 years is expected to cause significant aircraft delays and create a major financial burden for the airline industry unless the capacity of the National Airspace System can be increased. One approach to improve throughput and reduce delay is to develop new ground tools, airborne tools, and procedures to reduce the variance of aircraft delivery to the airport, thereby providing an increase in runway throughput capacity and a reduction in arrival aircraft delay. The first phase of the Merging and Spacing Concept employs a ground based tool used by Air Traffic Control that creates an arrival time to the runway threshold based on the aircraft s current position and speed, then makes minor adjustments to that schedule to accommodate runway throughput constraints such as weather and wake vortex separation criteria. The Merging and Spacing Concept also employs arrival routing that begins at an en route metering fix at altitude and continues to the runway threshold with defined lateral, vertical, and velocity criteria. This allows the desired spacing interval between aircraft at the runway to be translated back in time and space to the metering fix. The tool then calculates a specific speed for each aircraft to fly while enroute to the metering fix based on the adjusted land timing for that aircraft. This speed is data-linked to the crew who fly this speed, causing the aircraft to arrive at the metering fix with the assigned spacing interval behind the previous aircraft in the landing sequence. The second phase of the Merging and Spacing Concept increases the timing precision of the aircraft delivery to the runway threshold by having flight crews using an airborne system make minor speed changes during enroute, descent, and arrival phases of flight. These speed changes are based on broadcast aircraft state data to determine the difference between the actual and assigned time interval between the aircraft pair. The airborne software then calculates a speed adjustment to null that difference over the remaining flight trajectory. Follow-on phases still under development will expand the concept to all types of aircraft, arriving from any direction, merging at different fixes and altitudes, and to any airport. This paper describes the implementation phases of the Merging and Spacing Concept, and provides high-level results of research conducted to date.
Baxley, Brian T.↗
STOL and STOVL hot gas ingestion and airframe heating tests in the NASA Lewis 9- by 15-foot low-speed wind tunnel
Short takeoff and landing (STOL) and advanced short takeoff and vertical landing (STOVL) aircraft are being pursued for deployment near the end of this century. These concepts offer unique capabilities not seen in conventional aircraft: for example, shorter takeoff distances and the ability to operate from damaged runways and remote sites. However, special technology is critical to the development of this unique class of aircraft. Some of the real issues that are associated with these concepts are hot gas ingestion and airframe heating while in ground effects. Over the past nine years, NASA Lewis Research Center has been involved in several cooperative programs in the 9- by 15 Foot Low-Speed Wind Tunnel (LSWT) to establish a database for hot gas ingestion and airframe heating. The modifications are presented that were made in the 9- by 15-Foot LSWT, including the evolution of the ground plane, model support system, and tunnel sidewalls; and flow visualization techniques, instrumentation, test procedures, and test results. The 9- by 15-Foot LSWT tests were conducted at full scale exhaust nozzle pressure ratios. The headwind velocities varied from 8 to 120 kn depending on the concept (STOL or STOVL). Typical compressor-face distortions (pressure and temperature), ground plane contours, and model surface temperature profiles are presented.
Johns, Albert L.↗
Aeroacoustic Computations of a Generic Low Boom Concept in Landing Configuration: Part 1 - Aerodynamic Simulations
Computational results are presented for a 15%-scale, full-span, generic low-boom concept aircraft model simulated as installed in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel and in free-air conditions. The simulations were conducted with the lattice Boltzmann solver PowerFLOW® to capture the time-accurate characteristics of the flow. The aerodynamic behavior of the aircraft was investigated with various combinations of flap and landing gear deployments. To replicate the flow speed used during tests of the model, a Mach number of approximately 0.20 was chosen while varying the angle of attack through a limited range. Analyses were performed on local flow quantities, global forces, as well as flow distributions between configurations. Aerodynamic quantities were shown to be sensitive to mesh resolution levels, especially with flap and landing gear systems retracted. When comparing wind tunnel to free-air simulations, the aerodynamic quantities sampled were found to be in good agreement, suggesting that tunnel blockage and model support effects did not adversely impact the aerodynamic behavior of the model during the wind tunnel test. The results of this study improve our understanding of the highly complex, vortical flow generated by configurations with swept, low aspect-ratio wings at speeds encountered during landing operations.
low boom↗
Directivity and trends of noise generated by a propeller in a wake
An experimental study of the effects on far-field propeller noise of a pylon wake interaction was conducted with a scale model of a single-rotation propeller in a low-speed anechoic wind tunnel. A detailed mapping of the noise directivity was obtained at 10 test conditions covering a wide range of propeller power landings at several subsonic tip speeds. Two types of noise penalties were investigated-pulser and spacing. The pusher noise penalty is the difference in the average overall sound pressure level, OASPL, for pusher and tractor installations. (In a pusher installation, the propeller disk is downstream of a pylon or another aerodynamic surface.) The spacing noise penalty is the difference in the average OASPL for different distances between the pylon trailing edge and the propeller. The variations of these noise penalties with axial, or flyover, angle theta and circumferential angle phi are presented, and the trends in these noise penalties with tip Mach number and power loading are given for selected values of theta and phi. The circumferential directivity of the noise from a pusher installation showed that the addition noise due to the interaction of the pylon wake with the propeller had a broad peak over a wide range of circumferential angles approximately perpendicular to the pylon with a sharp minimum 90 deg. to the pylon for the majority of cases tested. The variation of the pusher noise penalty with theta had a minimum occurring near the propeller plane and maximum values of as much as 20 dB occurring toward the propeller axes. The magnitude of the pusher noise penalty generally decreased as propeller tip Mach number or power loading was increased.
Block, P. J. W.↗
Experimental landings in a spoiler-equipped light aircraft.
This report presents the results of a flight test program to determine the effects on landings of wide variations in approach path angle and approach airspeed for different kinds of piloting technique. Over 400 landings were made at approach speeds from 60 to 120 mph and approach path angles from 3 to 18 deg. Several variations of pilot technique involving different operations of the throttle/spoiler control were investigated. It is shown that very large ranges of airspeed and approach path angle can be accommodated with rather moderate penalties in landing distance and difficulty. With the spoiler-equipped aircraft, the best approach speeds are considerably higher than would be usable without spoilers, and approach path angles can be used which are far beyond those normally possible without spoilers.
Seckel, E.↗
An aerodynamic comparison of blown and mechanical high lift airfoils
Short takeoff and landing (STOL) performance utilizing a circulation control airfoil was successfully demonstrated on the A-6 CCW (circulation control wing). Controlled flight at speeds as slow as 67 knots was demonstrated. Takeoff ground run and liftoff speed reductions in excess of 40 and 20 percent respectively were achieved. Landing ground roll and approach speeds were similarly reduced. The technology demonstrated was intended to be useable on modern high performance aircraft. STOL performance would be achieved through the combination of a 2-D vectored nozzle and a circulation control type of high lift system. The primary objective of this demonstration was to attain A-6 CCW magnitude reductions in takeoff and landing flight speed and ground distance requirements using practical bleed flow rates from a modern turbofan engine for the blown flap system. Also, cruise performance could not be reduced by the wing high lift system. The A-6 was again selected as the optimum demonstration vehicle. The procedure and findings of the study to select the optimum high lift wing design are documented. Some findings of a supercritical airfoil and a comparison of 2-D and 3-D results are also described.
Carr, John E.↗
Reversed cowl flap inlet thrust augmentor
An adjustable airfoil is described for varying the geometry of a jet inlet and an ejector inlet in a jet engine for providing thrust augmentation and noise reduction. The airfoil comprises essentially a plurality of segments which are extended radially outward and retracted relative to the longitudinal axis of the engine as a function of a change in the pressure differential between the upstream and downstream surfaces of the airfoil. A servo mechanism responsive to the change in the pressure differential is coupled to the airfoil to extend and retract the airfoil segments to maintain the pressure at a maximum on the downstream side of the airfoil relative to the pressure on the upstream side of the airfoil. At low speeds, such as at take-offs and landings, the airfoil is fully extended while at high speeds it is fully retracted.
Cheng, D. Y.↗
Low-speed flight characteristics of a powered- lift jet transport during the landing approach
Flight characteristics of large jet transports with powered-lift systems
FLIGHT CHARACTERISTICS↗