Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOADS - RINGS, CIRCULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Single-stage experimental evaluation of low aspect ratio, highly loaded blading for compressors. Part 9: Stage F and stage G, volume 1

Two single-stage, 0.77 hub/tip ratio axial-flow compressors were tested to evaluate the effectiveness of low aspect ratio blading as a means of obtaining higher stage loadings. One compressor, designated Stage F, was comprised of circular arc blading with an aspect ratio of 0.9 for both the rotor and stator. This compressor was tested with uniform inlet flow, hub radial, tip radial, and 180 deg arc circumferential inlet distortion. The second compressor, designated Stage G, was comprised of multiple circular arc blading with an aspect ratio of 1.0 for both the rotor and stator. This compressor was tested with uniform inlet flow only. Design rotor tip speeds for Rotor F and Rotor G were 285 m/sec (934 ft/sec) and 327 m/sec (1,074 ft/sec) respectively. Both stages operated at high loading levels with adequate efficiency and operating range. The peak efficiencies and corresponding average stage diffusion factors for Stages F and G at design rotor speed were 86.4% and 84.1% and 0.59 and 0.55 respectively. The surge margin at peak efficiency for Stage F was 12.6% and the corresponding value for Stage G was 16.5%. Both stages experienced a loss in efficiency with increasing rotor speed; however, the multiple circular arc rotor delayed the characteristic loss in efficiency within increasing Mach number to higher Mach number.

Cheatham, J. G.↗
NASA NTRS1947

Some Investigations of the General Instability of Stiffened Metal Cylinders IX : Criterions for the Design of Stiffened Metal Cylinders Subject to General Instability Failures

Results are presented of an experimental investigation of the general instability of reinforced thin-walled metal cylinders subjected to pure bending and pure torsion over a range of geometrical quantities and structural sectional characteristics. Based on the experimental results and an existing theory of unstiffened metal cylinders, parameters were evolved which make possible an estimate of the stress at which general instability will occur for any given stiffened metal structure of circular cross section. (author)

STRESSED SKIN - CYLINDERS, METAL↗
NASA NTRS1987

Effects of transverse shear deformation on buckling of laminated cylinders as a function of thickness and ply orientation

Buckling loads of thick-walled, orthotropic, simply-supported right circular cylinders are predicted using a new higher-order transverse shear deformation theory. The higher-order theory shows that, by more accurately accounting for transverse shear deformation effects, the predicted buckling load may be reduced by as much as 80 percent compared to predictions based on conventional transverse shear deformation theory. A parametric study of the effect of ply orientation on the buckling load of axially compressed cylinders indicates that laminates containing 0 deg plies are the most sensitive to transverse shear deformation effects. Interaction curves for buckling of cylinders with axial compressive and external pressure loadings indicate that buckling loads due to external pressure loadings are much less sensitive to transverse shear deformation effects than those due to axial compressive loadings.

Jegley, Dawn C.↗
NASA NTRS1974

A method for determining local elastoplastic stress and strain in metallurgically bonded notched laminates subjected to a loading cycle

A semianalytical method was developed for determining elastoplastic cyclic stresses and strains at notch roots in metallurgically bonded metal laminates. The method is based on the Neuber equation, which was used with an effective stress-strain curve for the laminate. It was applied to laminates containing a circular hole which were subjected to one cycle of reversed loading. The laminates consisted of two elasto-perfectly-plastic materials with different yield strengths and with either equal or different Young's moduli. A laminate of high-strength titanium alloy with alternate layers of commercially pure titanium was also analyzed. The accuracy of the method was evaluated by comparing the stresses and strains with those calculated from a finite-element analysis. The results estimated by the simple method based on the Neuber equation agreed closely with the results computed from the more elaborate finite-element analysis.

Sova, J. A.↗
NASA NTRS1991

Compression behavior of graphite-thermoplastic and graphite-epoxy panels with circular holes or impact damage

An experimental investigation of the compression behavior of laminated specimens made from graphite-epoxy tape, graphite-thermoplastic tape and graphite-thermoplastic fabric was conducted. Specimens with five different stacking sequences were loaded to failure in uniaxial compression. Some of the specimens had central circular holes with diameters up to 65 percent of the specimen width. Other specimens were subjected to low speed impact with impact energies up to 35 J prior to compressive loading. This investigation indicates that graphite-thermoplastic specimens with holes have up to 15 percent lower failure stresses and strains than graphite-epoxy specimens with the same stacking sequence and hole size. However, graphite-thermoplastic specimens subjected to low speed impact have up to 15 percent higher failure stresses and strains than graphite-epoxy specimens with the same stacking sequence and impact energy. Compression tests of graphite-thermoplastic specimens constructed of unidirectional tape and fabric indicate that the material form has little effect on failure strains in specimens with holes or low speed impact damage.

Jegley, Dawn C.↗
NASA NTRS1968

Buckling of thin-walled circular cylinders

This monograph indicates current practices for predicting buckling of uniform stiffened and unstiffened circular cylindrical shells under various types of static loading, and suggests the procedures that yield estimates of static buckling loads considered to be conservative. The buckling of truncated conical shells and shells of double curvature will be treated in separate monographs.

V. I. Weingarten↗
NASA NTRS1977

An experimental study of the fracture behavior of laminated graphite/epoxy composites

The results of an experimental investigation on the fracture behavior of unidirectional and multidirectional laminated graphite/epoxy composites is reported. Critical tensile fracture stresses for constant head rate uniaxial specimens containing single-edge notches, double-edge notches, and centrally located circular holes are presented. Results are reported for loads and notches at various angles to the fiber direction. Evidence of notch sensitivity and stable crack growth is presented. Self-similar crack growth is shown to occur for only a limited set of circumstances. Critical stresses are compared to the theories of Waddoups et al and Whitney et al. These comparisons are presented using isotropic and orthotropic stress concentration factors together with a finite width correction factor. The results tend to show that use of only isotropic correction factors allow good correlation between theory and experiment.

Brinson, H. F.↗
NASA NTRS1980

Composite materials research and education program: The NASA-Virginia Tech composites program

Major areas of study include: (1) edge effects in finite width laminated composites subjected to mechanical, thermal and hygroscopic loading with temperature dependent material properties and the influence of edge effects on the initiation of failure; (2) shear and compression testing of composite materials at room and elevated temperatures; (3) optical techniques for precise measurement of coefficients of thermal expansion of composites; (4) models for the nonlinear behavior of composites including material nonlinearity and damage accumulation and verification of the models under biaxial loading; (5) compressive failure of graphite/epoxy plates with circular holes and the buckling of composite cylinders under combined compression and torsion; (6) nonlinear mechanical properties of borsic/aluminum, graphite/polyimide and boron/aluminum; (7) the strength characteristics of spliced sandwich panels; and (8) curved graphite/epoxy panels subjected to internal pressure.

Herakovich, C. T.↗
NASA NTRS1981

Stress-concentration factors for finite orthotropic laminates with a pin-loaded hole

Stresses were calculated for finite size orthotropic laminates loaded by a frictionless steel pin in a circular hole of the same diameter. The calculations were based on finite element analyses for six laminates. Stress concentration factors, based on nominal bearing stress, were determined for wide ranges of the ratios of width to diameter, w/d and edge distance to diameter, e/d. An infinite laminate case was analyzed for each laminate. Orthotropy had a significant influence on the tensile stress concentration at the hole. For example, the stress concentration factors for the infinite laminate cases ranged from 0.82 to 2.16, compared with 0.87 for the quasi-isotropic laminate. The finite widths and edge distances strongly influenced the tensile stress concentration. For the practical range w/d or = 3, the peak tensile stresses were as much as 80% larger than the infinite laminate reference value. For e/d or = 3, these stresses were amplified by as much as 50%. In contrast, the finite width and edge distance had little effect on shear-out and bearing stress concentrations.

Crews, J. H., Jr.↗
NASA NTRS1984

Stress analysis of multilayered plates around circular holes

The elasticity problem for a thick plate consisting of two bonded dissimilar homogeneous layers is considered. It is assumed that the plate is infinite, contains a circular hole, and is subjected to axisymmetric external loads. A technique suitable to the formulation of three-dimensional boundary value problems is introduced and applied to the three-dimensional elasticity solution of an infinite plate with a hole. The effect of Poisson's ratio is studied in some detail, and the axisymmetric problem of a laminated plate is solved. The stresses at the interface are calculated and are observed to become unbounded at the hole boundary. An approximate treatment of the singularity is presented and the stress intensity factors are computed. Some of the results are compared with those found from the finite element method. The agreement between the two sets with regard to trend and magnitude is found to be very satisfactory.

Delale, F.↗
NASA NTRS1989

Experimental observations and finite element analysis of the initiation of fiber microbuckling in notched composite laminates

An understanding was developed of the factors that determine the semi-circular edge-notched compressive strength and the associated failure mode(s) were identified of thermoplastic composite laminates with multidirectional stacking sequences. The experimental observations and the detailed literature review suggest at least four factors that affected the determination of the strain levels at which fiber microbuckling initiates and thus, partially control the composite's compression strength. The dependent variables studied are the compressive strength of a reduced gage section compression specimen and the compression strength of a compression specimen with two semi-circular edge notches (no opposite free edges) centered along the gage section. In this research, specimens containing two semi-circular edge notches (no opposite free edges) were loaded in compression at a relatively slow rate to provide more stable development of fiber microbuckling damage. The results indicate that the local constraints (free surfaces, supporting ply orientation, and resin-rich regions) significantly affect the strain level for the initiation of in-plane fiber microbuckling. Preliminary results at an elevated temperature, 77 C, showed the shear stress yield strength of the resin was reduced and consequently, the resistance to fiber microbuckling was also reduced. The finite element analysis of the perfectly straight fiber problem indicates that the free surface effect causes a 10 percent reduction in the critical buckling strain. However, the experimentally measured reduction for fibers with an initial fiber curvature, was 35 percent.

Guynn, E. Gail↗
NASA NTRS1990

The use of curvilinear fiber format to improve buckling resistance of plates with central circular holes

The potential gain in buckling resistance is explored by using the curvilinear format with a plate containing a centrally located circular hole and subjected to a uniaxial compressive load. The buckling loads for a uniform stress loading and simple support boundary conditions were examined. The method of analysis is outlined for the buckling improvement study. Several designs that represent an improvement over a baseline quasi-isotropic design (a design that is quite good for buckling resistance) are discussed. The tensile load of these designs is examined. A recommended design is presented that not only shows an improved buckling capacity, but also shows improved tensile performance. Follow-on activities are also discussed.

Lee, H. H.↗
NASA NTRS1961

Theoretical Elastic Stress Distributions Arising from Discontinuities and Edge Loads in Several Shell-Type Structures

The deformation and complete stress distribution are determined for each of the following edge loaded thin shells of revolution: (1) a right circular cylinder, (2) a frustum of a right circular cone, and (3) a portion of a sphere. The locations of the maximum circumferential and meridional stresses on both the inner and outer surfaces are also found. The basic equations for the above were selected from the published literature on the subject and expanded to produce to resultant-stress equations in closed from where practicable to do so. Equations are also developed for the discontinuity shear force and bending moment at each of the following junction: (1) axial change of thickness in a circular cylinder, (2) axial change of thickness in a cone, (3) change of thickness in a portion of a sphere, (4) a cylinder and a cone, (5) a cylinder and a portion of a sphere(6) a cylinder and a flat head, and (7) a cone and a portion of a sphere.

Johns, Robert H.↗
NASA NTRS1990

Compression behavior of graphite-epoxy and graphite-thermoplastic panels with circular holes or impact damage

An experimental investigation of the compression behavior of laminated specimens made from graphite-epoxy tape (AS4-3502), graphite-thermoplastic tape (AS4-PEEK), and graphite-thermoplastic fabric (AS4-PEEK) was conducted. Specimens with five different stacking sequences were loaded to failure in uniaxial compression. Some of the specimens had central circular holes with diameters up to 65 percent of the specimen width. Other specimens were subjected to low speed impact with impact energy up to 30 J prior to compressive loading. This investigation indicates that graphite-thermoplastic specimens with holes have up to 15 percent lower failure stresses and strains than graphite-epoxy specimens with the same stacking sequence and hole size. However, graphite-thermoplastic specimens subjected to low speed impact have up to 15 percent higher failure stresses and strains than graphite-epoxy specimens with the same stacking sequence and impact energy. Compression tests of graphite-thermoplastic specimens constructed of unidirectional tape and of fabric indicate that the material form has little effect on failure strains in specimens with holes or low speed impact damage.

Jegley, Dawn C.↗
NASA NTRS2010

Comparison of Methods to Predict Lower Bound Buckling Loads of Cylinders Under Axial Compression

Results from a numerical study of the buckling response of two different orthogrid stiffened circular cylindrical shells with initial imperfections and subjected to axial compression are used to compare three different lower bound buckling load prediction techniques. These lower bound prediction techniques assume different imperfection types and include an imperfection based on a mode shape from an eigenvalue analysis, an imperfection caused by a lateral perturbation load, and an imperfection in the shape of a single stress-free dimple. The STAGS finite element code is used for the analyses. Responses of the cylinders for ranges of imperfection amplitudes are considered, and the effect of each imperfection is compared to the response of a geometrically perfect cylinder. Similar behavior was observed for shells that include a lateral perturbation load and a single dimple imperfection, and the results indicate that the predicted lower bounds are much less conservative than the corresponding results for the cylinders with the mode shape imperfection considered herein. In addition, the lateral perturbation technique and the single dimple imperfection produce response characteristics that are physically meaningful and can be validated via testing.

Haynie, Waddy T.↗
NASA NTRS1979

Wing aerodynamic loading caused by jet-induced lift associated with STOL-OTW configurations

Surface pressure distributions were obtained with model-scale STOL-OTW configurations using various nozzles designed to promote flow attachment to the wing/flap surface. The nozzle configurations included slot-types and both circular and slot nozzles with external flow deflectors. The wing aerodynamic loading caused by the jet-induced lift is presented in conventional terms of delta p/q as a function of chordwise surface distance in the nozzle centerline plane as well as outboard of the nozzle centerline. Nozzle roof/deflector angle, chordwise location of the nozzle, wing size, and flap deflection angle are included in the geometric variables affecting the wing loading.

Vonglahn, U.↗