Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOADS AND STRESSES, STRUCTURAL - TRANSIENT DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Fracture Mechanics Analysis of LH2 Feed Line Flow Liners

Inspections of the Space Shuttle Main Engine revealed fatigue cracks growing from slots in the flow liner of the liquid hydrogen (LH2) feed lines. During flight, the flow liners experience complex loading induced by flow of LH2 and the resonance characteristics of the structure. The flow liners are made of Inconel 718 and had previously not been considered a fracture critical component. However, fatigue failure of a flow liner could have catastrophic effect on the Shuttle engines. A fracture mechanics study was performed to determine if a damage tolerance approach to life management was possible and to determine the sensitivity to the load spectra, material properties, and crack size. The load spectra were derived separately from ground tests and material properties were obtained from coupon tests. The stress-intensity factors for the fatigue cracks were determined from a shell-dynamics approach that simulated the dominant resonant frequencies. Life predictions were obtained using the NASGRO life prediction code. The results indicated that adequate life could not be demonstrated for initial crack lengths of the size that could be detected by traditional NDE techniques.

James, Mark A.↗
DOE OSTI2026

Dynamic crushing of metal lattice metamaterials: Shock mode diagrams and transition to topology-independent compaction regime

Additively manufactured lattice metamaterials offer design versatility in strength and energy absorption and provide an additional degree of freedom through the selection of the lattice topology. Under quasistatic loading, the unit cell structure can strongly affect the stiffness, yield, and post-yield behavior, but whether and to what degree the effect of lattice topology persists into dynamic loading scenarios, up to the compaction shock regime, has not been established. LLNL’ s ALE3D hydrocode was used to perform a computational investigation of dynamic loading in multiple lattice types, including the gyroid, octet, Schwarz D, and rhombic dodecahedron, under impact velocities from 0.25 to 2.25 km/s. Shock Hugoniots for each lattice topology are generated and compared, suggesting that above a critical velocity, distinctions between architectures may not persevere and compacted lattices behave similarly. Here, to investigate the transition between topology-dependent quasistatic compression and the topology-independent regime above the critical velocity, a one-dimensional elastic-linear hardening plasticity-densified solid (E-LHP-DS) shock model for lattice materials was developed that relies upon confined compression to link the quasistatic and shock mechanics. Unlike similar works, the model does not assume rigid behavior prior to yield or locking behavior at densification, allowing a richer exploration of lattice mechanics. With only six parameters, the analytical model simultaneously fit quasistatic confined compression simulations for relative densities 0.1 $≤ \bar{ρ} ≤$ 0.9 and predicted dynamic compaction behavior to traverse several distinct shock modes, each defined by a critical impact speed (equivalently, critical stresses). Comparing the numerical results to the one-dimensional E-LHP-DS shock model predictions suggests that the topology-independence under strong shocks is linked to the onset of densification, which can be predicted based on quasistatic confined compression results.

Cellular material↗
DOE OSTI2026

Mechanics of pore array collapse and interaction in shock-compressed polymethyl methacrylate (PMMA)

Recent studies on dynamic pore collapse have revealed significant development of shear localization, which can lead to material failure in porous structures and hot spot generation in energetic materials. These findings have dramatically improved the understanding of failure mechanisms during pore collapse but also prompt further investigation of realistic porous materials. In particular, porous media consist of many pores and porous networks. Even in low-porosity materials, pores can form in close proximity during the manufacturing process, leading to the critical question of pore–pore interaction during collapse under dynamic loading conditions. This study investigates, via plate impact experiments coupled with high-speed internal digital image correlation and shadowgraphy techniques, the collapse of two pores in shock-compressed PMMA at stresses between 0.4 and 1 GPa. The results of these experiments provide new insights into shear localization in pore collapse, in addition to distinct interactions between pores. Shadowgraphy measurements reveal novel, direct visualization of shear band development and crack evolution from pore surfaces. Spacing between adiabatic shear bands is measured over a range of impact stresses and is predicted accurately by the Grady–Kipp model. Pore interactions are found to effect a transition in the impact stress threshold at which different failure mechanisms initiate and are also found to possibly influence preferential sites for shear cracking. Throughout the study, numerical and theoretical models are leveraged to understand shear localization behavior. The role of baroclinicity and wave interactions between the pores is used to elucidate interaction mechanisms between pores.

Lawlor, Barry P. [California Institute of Technolo↗
NASA NTRS1994

Atomic oxygen durability evaluation of the flexible batten for the photovoltaic array mast on Space Station

A test program was conducted at the National Aeronautics and Space Administration's Lewis Research Center (LeRC) to evaluate the long term low Earth orbital (LEO) atomic oxygen (AO) durability of a flexible (fiberglass-epoxy composite) batten. The flexible batten is a component used to provide structural rigidity in the photovoltaic array mast on Space Station. The mast is used to support and articulate the photovoltaic array, therefore, the flexible batten must be preloaded for the 15 year lifetime of an array blanket. Development hardware and composite materials were evaluated in ground testing facilities for AO durability and dynamic retraction-deployment cyclic loading representative of expected full life in-space application. The CV1144 silicone (AO protective) coating was determined to provide adequate protection against AO degradation of the composite material and provided fiber containment, thus the structural integrity of the flexible batten was maintained. Both silicone coated and uncoated flexible battens maintained load carrying capabilities. Results of the testing did indicate that the CV1144 silicone protective coating was oxidized by AO reactions to form a brittle glassy (SiO2) skin that formed cracking patterns on all sides of the coated samples. The cracking was observed in samples that were mechanically stressed as well as samples in non-stressed conditions. The oxidized silicon was observed to randomly spall in small localized areas, on the flexible battens that underwent retraction-deployment cycling. Some darkening of the silicon, attributed to vacuum ultraviolet (VUV) radiation, was observed.

Stidham, Curtis R.↗
DOE OSTI2025

Multi-objective automatic discovery of optimized metamaterials for varying velocity impact protection

Mechanical metamaterials have demonstrated exceptional impact performance while remaining lightweight. Impact resistance has traditionally been investigated using quasi-static simulations, often with the assumption that performance will translate to high-velocity impact scenarios. However, critical crash protection parameters—such as peak stress and absorbed energy—are highly sensitive to impact velocity, leading to inconsistent performance under dynamic loading. To address this, we introduce a strain-rate-aware, active deep learning framework that enables multi-objective optimization of impact protection metrics across a wide range of impact velocities. Our framework captures the strain-rate sensitivity of architected lattices by learning to control spatial gradation in cellular metamaterials, resulting in over 200 % enhancement in impact protection relative to state-of-the-art designs such as Voronoi and re-entrant lattices. We demonstrate its practical utility by designing next-generation lattice structures for automotive bumper systems that satisfy multiple, velocity-specific safety criteria—capabilities beyond those of conventional designs. More than just a predictive tool, this framework marks the first step towards enabling adaptable impact-resistant structures across dynamic regimes.

Deep learning↗
DOE OSTI2021

Strongly Anisotropic Thermomechanical Response to Shock Wave Loading in Oriented Samples of the Triclinic Molecular Crystal 1,3,5-Triamino-2,4,6-trinitrobenzene

All-atom molecular dynamics (MD) simulations were used to study shock wave loading in oriented single crystals of the highly anisotropic triclinic molecular crystal 1,3,5-triamino-2,4,6-trinitrobenzene (TATB). The crystal structure consists of planar hydrogen-bonded sheets of individually planar TATB molecules that stack into graphitic-like layers. Shocks were studied for seven systematically prepared crystal orientations with limiting cases that correspond to shock propagation exactly perpendicular and exactly parallel to the graphitic-like layers. The simulations were performed for initially defect-free crystals using a reverse-ballistic configuration that generates explicit, supported shocks. Final longitudinal stress components are between ≈8.5 and ≈10.5 GPa for the 1.0 km s –1 impact speed studied. Orientation-dependent properties are reported including shock speeds, stresses, temperatures, compression ratios, and local material strain rates. Spatiotemporal maps of the temperature, stress tensor, material flow, and molecular orientations reveal complicated processes that arise for specific shock directions. Furthermore, the results indicate that TATB shock response is highly sensitive to crystal orientation, with significant qualitative differences for the time evolution of the stress tensor and temperature, elastic/inelastic compression response, defect formation and growth, critical von Mises stress, and strain rates during shock rise that span nearly an order of magnitude. A variety of inelastic deformation mechanisms are identified, ranging from crumpling of graphitic-like layers to dislocation-mediated plasticity to intense shear strain localization. To our knowledge, these are the first systematic MD simulations and analysis of explicit shock wave propagation along nontrivial crystal directions in a triclinic molecular crystal.

36 MATERIALS SCIENCE↗
NASA NTRS2001

Dynamic Analysis of a Building Under Rocket Engine Plume Acoustic Load

Studies have been performed to develop finite-element modeling and simulation techniques to predict the dynamic structural response of Building 4010 to the acoustic load from the plume of high-thrust rocket motors. The building is the Test Control Center and general office space for the E-complex at Stennis Space Center. It is a large single span; light-structured building located approximately 1,000 feet from the E-1 test stand. A three-dimensional shell/beam combined model of the building was built using Pro/Engineer platform and imported into Pro/Mechanica for analysis. An Equivalent Shell technique was developed to simplify the highly complex building structure so that the calculation is more efficient and accurate. A deterministic approach was used for the dynamic analysis. A pre-stressed modal analysis was performed to simulate the weight stiffening of the structure, through which about 200 modes ranging from 0 to 35 Hz were identified. In an initial dynamic frequency analysis, the maximum response over the model was found. Then the complete 3-D distributions of the displacement, as well as the stresses, were calculated through a final frequency analysis. The results were compared to a strain gage and accelerometer recordings from rocket engine tests and showed reasonable agreement.

Qian, Z.↗
DOE OSTI2022

Multiphysics Analyses of the Bottom Components of the 3D Printed Transformational Challenge Reactor

This research presents multi-physics analyses on the bottom components of the Transformational Challenge Reactor (TCR) facility. These components include the bottom axial reflector and the steel exit cone. The bottom axial reflector is made of pure silicon carbide elements hosting helium cooling channels These elements are 3D printed and therefore can host any arbitrary shape of the helium cooling channels. The design of the bottom reflector considers the neutronics and thermo-fluid dynamics performances as well as the manufacturing process optimization. More precisely, the best design of the bottom reflector reduces neutron leakage by avoiding straight cylindrical helium channels that facilitate neutron leakage, minimizes the helium flow pressure drop, and reduces the number of 3D printed silicon carbide pieces. The exit cone steel structure collects the hot helium from the bottom fuel assemblies and channels the cold helium to the top of the fuel assemblies. The steel simultaneous contact with hot and cold helium flows sets a large thermal gradient. Different designs of the exit cone are proposed to reduce the steel equivalent stress from the helium thermal load. The multi-physics analyses have been performed using Ansys Fluent, Ansys Mechanical, STAR-CCM+, and Serpent computer programs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Anisotropic strength behavior of single-crystal TATB

High-rate strength behavior plays an important role in the shock initiation of high explosives, with plastic deformation serving to localize heat into hot spots and as a mechanochemical means to enhance reactivity. Recent simulations predict that detonation-like shocks produce highly reactive nanoscale shear bands in the layered crystalline explosive TATB (1,3,5-triamino-2,4,6-trinitrobenzene), but the thresholds leading to this response are poorly understood. We utilize molecular dynamics to simulate the high-rate compressive stress–strain response of TATB, with a focus on understanding flow behavior. Here, the dependence of strength on pressure and loading axis (crystal orientation) is explored. The deformation mechanisms fall broadly into two categories, with compression along crystal layers activating a buckling/twinning mode and compression normal to the layers producing nanoscale shear bands. Despite the complexity of the underlying mechanisms, the crystal exhibits relatively straightforward stress–strain curves. Most of the crystal orientations studied show rapid strain softening following the onset of yielding, which settles to a steady flow state. Trajectories are analyzed using five metrics for local states and structural order, but most of these metrics yield similar distributions for these deformation mechanisms. On the other hand, a recently proposed measure of intramolecular strain energy is found to most cleanly distinguish between these mechanisms, while also providing a plausible connection with mechanochemically accelerated decomposition kinetics. Localization of intramolecular strain energy is found to depend strongly on crystal orientation and pressure.

36 MATERIALS SCIENCE↗
NASA NTRS2003

CARES/LIFE Ceramics Analysis and Reliability Evaluation of Structures Life Prediction Program

This manual describes the Ceramics Analysis and Reliability Evaluation of Structures Life Prediction (CARES/LIFE) computer program. The program calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. CARES/LIFE is an extension of the CARES (Ceramic Analysis and Reliability Evaluation of Structures) computer program. The program uses results from MSC/NASTRAN, ABAQUS, and ANSYS finite element analysis programs to evaluate component reliability due to inherent surface and/or volume type flaws. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing the power law, Paris law, or Walker law. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled by using either the principle of independent action (PIA), the Weibull normal stress averaging method (NSA), or the Batdorf theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. The probabilistic time-dependent theories used in CARES/LIFE, along with the input and output for CARES/LIFE, are described. Example problems to demonstrate various features of the program are also included.

Nemeth, Noel N.↗
NASA NTRS2006

Low-Velocity Impact Response of Sandwich Beams with Functionally Graded Core

The problem of low-speed impact of a one-dimensional sandwich panel by a rigid cylindrical projectile is considered. The core of the sandwich panel is functionally graded such that the density, and hence its stiffness, vary through the thickness. The problem is a combination of static contact problem and dynamic response of the sandwich panel obtained via a simple nonlinear spring-mass model (quasi-static approximation). The variation of core Young's modulus is represented by a polynomial in the thickness coordinate, but the Poisson's ratio is kept constant. The two-dimensional elasticity equations for the plane sandwich structure are solved using a combination of Fourier series and Galerkin method. The contact problem is solved using the assumed contact stress distribution method. For the impact problem we used a simple dynamic model based on quasi-static behavior of the panel - the sandwich beam was modeled as a combination of two springs, a linear spring to account for the global deflection and a nonlinear spring to represent the local indentation effects. Results indicate that the contact stiffness of thc beam with graded core Increases causing the contact stresses and other stress components in the vicinity of contact to increase. However, the values of maximum strains corresponding to the maximum impact load arc reduced considerably due to grading of thc core properties. For a better comparison, the thickness of the functionally graded cores was chosen such that the flexural stiffness was equal to that of a beam with homogeneous core. The results indicate that functionally graded cores can be used effectively to mitigate or completely prevent impact damage in sandwich composites.

Apetre, N. A.↗
NASA NTRS1989

Probabilistic design analysis using Composite Loads Spectra (CLS) coupled with Probabilistic Structural Analysis Methodologies (PSAM)

Composite loads spectra (CLS) were applied to generate probabilistic loads for use in the PSAM nonlinear evaluation of stochastic structures under stress (NESSUS) finite element code. The CLS approach allows for quantifying loads as mean values and distributions around a central value rather than maximum or enveloped values typically used in deterministic analysis. NESSUS uses these loads to determine mean and perturbation responses. These results are probabilistically evaluated with the distributional information from CLS using a fast probabilistic integration (FPI) technique to define response distributions. The main example discussed describes a method of obtaining load descriptions and stress response of the second-stage turbine blade of the Space Shuttle Main Engine (SSME) high-pressure fuel turbopump (HPFTP). Additional information is presented on the on-going analysis of the high pressure oxidizer turbopump discharge duct (HPOTP) where probabilistic dynamic loads have been generated and are in the process of being used for dynamic analysis. Example comparisons of load analysis and engine data are furnished for partial verification and/or justification for the methodology.

Newell, J. F.↗
DOE OSTI2021

On the computational solution of vector-density based continuum dislocation dynamics models: A comparison of two plastic distortion and stress update algorithms

Continuum dislocation dynamics models of mesoscale plasticity consist of dislocation transport-reaction equations coupled with crystal mechanics equations. The coupling between these two sets of equations is such that dislocation transport gives rise to the evolution of plastic distortion (strain), while the evolution of the latter fixes the stress from which the dislocation velocity field is found via a mobility law. Earlier solutions of these equations employed a staggered solution scheme for the two sets of equations in which the plastic distortion was updated via time integration of its rate, as found from Orowan's law. In this work, we show that such a direct time integration scheme can suffer from accumulation of numerical errors. We introduce an alternative scheme based on field dislocation mechanics that ensures consistency between the plastic distortion and the dislocation content in the crystal. The new scheme is based on calculating the compatible and incompatible parts of the plastic distortion separately, and the incompatible part is calculated from the current dislocation density field. Stress field and dislocation transport calculations were implemented within a finite element based discretization of the governing equations, with the crystal mechanics part solved by a conventional Galerkin method and the dislocation transport equations by the least squares method. A simple test was first performed to show the accuracy of the two schemes for updating the plastic distortion, which shows that the solution method based on field dislocation mechanics is more accurate. This method then was used to simulate an austenitic steel crystal under uniaxial loading and multiple slip conditions. By considering dislocation interactions caused by junctions, a hardening rate similar to discrete dislocation dynamics simulation results was obtained. Finally, the simulations show that dislocations exhibit some self-organized structures as the strain is increased.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Water Weakening of Calcium Oxide

Chemomechanical processes such as water weakening can control the permeability and deformation of rocks and manmade materials. Here, atomistic modeling and nanomechanical experiments were used to identify molecular origins of chemomechanical effects in calcium oxide (CaO) and its effect on observed elastic, plastic, and brittle deformation. Classical molecular dynamics simulations with the bond order-based reactive force-field ReaxFF were used to assess brittle fracture. In the presence of water, CaO fractured earlier and more often during quasi-static loading, with a calculated reduction in fracture toughness of ~80% associated with changes in the stress distribution around the crack tip. Experimentally, elastic and plastic deformation of CaO surfaces exposed to water was assessed experimentally using in situ liquid nanoindentation. Nanoindentation showed that following exposure to water, the contact hardness decreased by 1–2 orders of magnitude and decreased the modulus by 2–3 orders of magnitude due to surface hydroxylation. Furthermore, the strong chemomechanical effects on the mechanical processes in CaO suggests that minerals with similar structures may exhibit comparable effects, influencing the stability of cements and geomaterials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1993

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program: Boeing Helicopters airframe finite element modeling

Mathematical models based on the finite element method of structural analysis, as embodied in the NASTRAN computer code, are routinely used by the helicopter industry to calculate airframe static internal loads used for sizing structural members. Historically, less reliance has been placed on the vibration predictions based on these models. Beginning in the early 1980's NASA's Langley Research Center initiated an industry wide program with the objective of engendering the needed trust in vibration predictions using these models and establishing a body of modeling guides which would enable confident future prediction of airframe vibration as part of the regular design process. Emphasis in this paper is placed on the successful modeling of the Army/Boeing CH-47D which showed reasonable correlation with test data. A principal finding indicates that improved dynamic analysis requires greater attention to detail and perhaps a finer mesh, especially the mass distribution, than the usual stress model. Post program modeling efforts show improved correlation placing key modal frequencies in the b/rev range with 4 percent of the test frequencies.

Gabel, R.↗
NASA NTRS2013

Three-Axis Distributed Fiber Optic Strain Measurement in 3D Woven Composite Structures

Recent advancements in composite materials technologies have broken further from traditional designs and require advanced instrumentation and analysis capabilities. Success or failure is highly dependent on design analysis and manufacturing processes. By monitoring smart structures throughout manufacturing and service life, residual and operational stresses can be assessed and structural integrity maintained. Composite smart structures can be manufactured by integrating fiber optic sensors into existing composite materials processes such as ply layup, filament winding and three-dimensional weaving. In this work optical fiber was integrated into 3D woven composite parts at a commercial woven products manufacturing facility. The fiber was then used to monitor the structures during a VARTM manufacturing process, and subsequent static and dynamic testing. Low cost telecommunications-grade optical fiber acts as the sensor using a high resolution commercial Optical Frequency Domain Reflectometer (OFDR) system providing distributed strain measurement at spatial resolutions as low as 2mm. Strain measurements using the optical fiber sensors are correlated to resistive strain gage measurements during static structural loading. Keywords: fiber optic, distributed strain sensing, Rayleigh scatter, optical frequency domain reflectometry

Castellucci, Matt↗
NASA NTRS1982

Impact resistance of fiber composites

Stress-strain curves are obtained for a variety of glass fiber and carbon fiber reinforced plastics in dynamic tension, over the stress-strain range of 0.00087-2070/sec. The test method is of the one-bar block-to-bar type, using a rotating disk or a pendulum as the loading apparatus and yielding accurate stress-strain curves up to the breaking strain. In the case of glass fiber reinforced plastic, the tensile strength, strain to peak impact stress, total strain and total absorbed energy all increase significantly as the strain rate increases. By contrast, carbon fiber reinforced plastics show lower rates of increase with strain rate. It is recommended that hybrid composites incorporating the high strength and rigidity of carbon fiber reinforced plastic with the high impact absorption of glass fiber reinforced plastics be developed for use in structures subjected to impact loading.

Chamis, C. C.↗
DOE OSTI2023

Biocompatible Co–P Metallic Glasses with Superior Degradation Tolerance in Physiological Environments

Metallic glasses represent a class of metallic alloys with a fully amorphous structure and attractive properties, making them promising in bioimplant applications. Here, the degradation tolerance of biocompatible cobalt–phosphorus (Co–P) metallic glasses was studied in a simulated physiological environment. The metallic glasses were synthesized in the form of coatings through a facile electrodeposition approach. This method utilizes their outstanding surface characteristics and bypasses the size limitations usually associated with their bulk counterparts. Further, the Co–P alloys showed exceptional tribological response with ~14% lower coefficient of friction and 2 orders of magnitude lesser wear rate compared to SS316 stainless steel. In addition, the Co–P alloys showed a 3 times higher hardness and 4 times higher hardness/modulus ratio compared to SS316, indicating better elastic recovery under dynamic shear stresses that are common in load-bearing bioimplants. The Co–P metallic glasses exhibited excellent hemocompatibility and cytocompatibility in terms of lower platelet adhesion, spreading, and aggregation, a hemolysis ratio lower than 1%, and enhanced surface wettability, suggesting a superlative performance in bioimplant applications.

36 MATERIALS SCIENCE↗