Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOW ALLOY STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Grain refinement of high strength steels to improve cryogenic toughness

Grain-refining techniques using multistep heat treatments to reduce the grain size of five commercial high-strength steels were investigated. The goal of this investigation was to improve the low-temperature toughness as measured by Charpy V-notch impact test without a significant loss in tensile strength. The grain size of four of five alloys investigated was successfully reduced up to 1/10 of original size or smaller with increases in Charpy impact energy of 50 to 180 percent at -320 F. Tensile properties were reduced from 0 to 25 percent for the various alloys tested. An unexpected but highly beneficial side effect from grain refining was improved machinability.

Rush, H. F.↗
NASA NTRS1998

High-Strength Aluminum Casting Alloy for High-Temperature Applications (MSFC Center Director's Discretionary Fund Final Project No. 97-10)

A new aluminum-silicon alloy has been successfully developed at Marshall Space Flight Center that has a significant improvement in tensile strength at elevated temperatures (550 to 700 F). For instance, the new alloy shows in average tensile strength of at least 90 percent higher than the current 390 aluminum piston alloy tested at 500 F. Compared to conventional aluminum alloys, automotive engines using the new piston alloy will have improved gas mileage, and may produce less air pollution in order to meet the future U.S. automotive legislative requirements for low hydrocarbon emissions. The projected cost for this alloy is less than $0.95/lb, and it readily allows the automotive components to be cast at a high production volume with a low, fully accounted cost. It is economically produced by pouring molten metal directly into conventional permanent steel molds or die casting.

Lee, J. A.↗
NASA NTRS1976

Nickel-free Fe-12Mn-0.2Ti alloy steel for cryogenic applications

A nickel-free Fe-12Mn-0.2Ti alloy steel was investigated for cryogenic applications. The systematic control of the grain size and the microstructural distribution of the retained gamma phase was made through alpha plus gamma heat treatments in combination with mechanical working. Substantial improvements of important low temperature mechanical properties were obtained by these processings.

Hwang, S.↗
NASA NTRS1972

On the cyclic stress-strain behavior and low cycle fatigue of aerospace materials

The elastic-plastic deformation behavior under cyclic stress of a number of different engineering materials was experimentally investigated with the aid of high-precision methods of measuring, some of which had been newly developed. Experiments made with a variety of steels, the titanium alloy Ti-A16-V4, a cobalt (tungsten) alloy, the high-temperature material Nimonic 90 and Dural (A1-Cu) are reported. The theory given in an attempt to explain these experiments is aimed at finding general formulas for the cyclic stress-strain behavior materials.

Burbach, J.↗
DOE OSTI2019

Evolution of TiS and TiN in Fe-40 MassPctNi Austenitic Alloy During Heating at 1273 K (1000 °C)

Evolution of TiS in composition and morphology as well as the change in size distribution of TiS and TiN in Fe-40 masspctNi austenitic alloy during heating at 1273 K (1000 °C) was investigated using manual/automatic scanning electron microscopy energy-dispersive X-ray spectroscopy (SEM/EDS). Two types of TiS morphologies, spindle and spherical, were maintained during heating. The molar ratio of Ti/S of TiS increased while the aspect ratio of TiS was maintained in both alloys during heating. The number density of TiN inclusions was low compared with TiS in each alloy during heating. The pinning effect of TiS during heating was confirmed, and was stronger in alloy with a larger volume fraction of TiS. The results contribute to the establishment of optimum heat treatment processes for austenitic stainless steel to obtain better pitting corrosion resistance.

36 MATERIALS SCIENCE↗
NASA NTRS1943

Description of stress-strain curves by three parameters

A simple formula is suggested for describing the stress-strain curve in terms of three parameters; namely, Young's modulus and two secant yield strengths. Dimensionless charts are derived from this formula for determining the stress-strain curve, the tangent modulus, and the reduced modulus of a material for which these three parameters are given. Comparison with the tensile and compressive data on aluminum-alloy, stainless-steel, and carbon-steel sheet in NACA Technical Note No. 840 indicates that the formula is adequate for most of these materials. The formula does not describe the behavior of alclad sheet, which shows a marked change in slope at low stress. It seems probable that more than three parameters will be necessary to represent such stress-strain curves adequately.

Ramberg, Walter↗
DOE OSTI2024

Al-Ce Alloy-Based Compact Heat Exchanger for Refrigerant Charge Reduction and Unprecedented Durability (CRADA NFE-21-08888 Final Report)

Oak Ridge National Laboratory and Eck Industries produced and characterized durable and corrosion resistant Al-Ce-Mg alloy-based heat exchanger. Eck Industries successfully casted Al-Ce-Mg heat exchanger. ORNL characterized reaction bonding between Al-2Ce-6Mg alloy and stainless-steel tube in a heat exchanger header. Metallurgical bonds were achieved between stainless steel tubes and Al-Ce-Mg alloy cast headers. ORNL performed corrosion testing on Al-Ce-Mg alloy/stainless steel tube reactive bond interface. In most cases no significant changes to the reactive bond morphology or compositional distribution were observed in the samples after exposure to acid for 267h acid.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Processing of IN-718 Lattice Block Castings

Recently a low cost casting method known as lattice block casting has been developed by JAM Corporation, Wilmington, Massachusetts for engineering materials such as aluminum and stainless steels that has shown to provide very high stiffness and strength with only a fraction of density of the alloy. NASA Glenn Research Center has initiated research to investigate lattice block castings of high temperature Ni-base superalloys such as the model system Inconel-718 (IN-718) for lightweight nozzle applications. Although difficulties were encountered throughout the manufacturing process , a successful investment casting procedure was eventually developed. Wax formulation and pattern assembly, shell mold processing, and counter gravity casting techniques were developed. Ten IN-718 lattice block castings (each measuring 15-cm wide by 30-cm long by 1.2-cm thick) have been successfully produced by Hitchiner Gas Turbine Division, Milford, New Hampshire, using their patented counter gravity casting techniques. Details of the processing and resulting microstructures are discussed in this paper. Post casting processing and evaluation of system specific mechanical properties of these specimens are in progress.

Hebsur, Mohan G.↗
DOE OSTI2022

Impact of Fill Factor on Electro-slag Remelting Operations

Vacuum induction melting (VIM), electro-slag remelting (ESR) and vacuum arc remelting (VAR) are all techniques used to make high quality ingots of complex chemistries. In some cases, all three are used, e.g., alloys for aerospace applications and increasingly those for fossil power applications under extreme conditions. Electroslag remelting operation is a complicated endeavor, dependent upon several factors including operating current, voltage, and geometry. A research scale 440 lb capacity ESR furnace was used to melt low carbon steel (1018 steel) electrodes of different diameters using various melt rates. This was used to assess melt parameters and sidewall and other quality aspects of the product ingots. These observations were compared to results from ESR modeling using MeltFlow-ESR. It was found that fill factor had a significant impact on operating voltage while current had a significant impact on melt rate. Ultimately, a combination of fill factor and power gave the best prediction of melt rate during steady state.

Jablonski, Paul↗
DOE OSTI2019

Influencing mechanism of pre-existing nanoscale Al 5 Fe 2 phase on Mg–Fe interface in friction stir spot welded Al-free ZK60–Q235 joint

Al-free ZK60 magnesium (Mg) alloy sheet was selected as substrate material of Mg–steel pinless friction stir spot welding (FSSW), avoiding the effect of the Al element in the substrate on the alloying reaction of Mg-iron (Fe) interface. The sound FSSW joint of ZK60 Mg alloy and Q235 steel with a hot-dipped aluminum (Al)-containing zinc (Zn) coating was successfully realized. The detailed microstructural examinations proved that Al 5 Fe 2 phase at the Mg-Fe interface came from the pre-existing Al 5 Fe 2 phase in the coating and acted as the transition layer for promoting the metallurgical bonding of Mg and Fe. The interfaces with well-matched lattice sites among Fe, Al 5 Fe 2 and Mg were formed during FSSW. A low energy interface with good match of lattice sites ((002) Al5Fe2 //(110) Fe , [110] Al5Fe2 //[13] Fe ) between Al 5 Fe 2 and Fe was identified. For the interface between Al5Fe2 and Mg, an orientation relationship of ( 6 2 ¯ 2 ) A l 5 F e 2 / / ( 3 1 ¯ 1 ¯ 2 ¯ ) M g and [ 1 5 ¯ 8 ¯ ] A l 5 F e 2 / / [ 2 4 ¯ 23 ] M g was observed. The tensile–shear load of the ZK60–steel joint could reach 4.6 kN. Moreover, the joint fracture occurred at the interface between the Al5Fe2 layer and the Mg alloy substrate, suggesting the brittle fracture characteristic.

36 MATERIALS SCIENCE↗
NASA NTRS2006

Metallurgical Design and Development of NASA Crawler/Transporter Tread Belt Shoe Castings

The NASA Crawler/Transporters (CT-1 and CT-2) used to transport the Space Shuffles are one of the largest tracked vehicles in existence today. Two of these machines have been used to move space flight vehicles at Kennedy Space Center since the Apollo missions of the 1960's and relatively few modifications have been made to keep them operational. In September of 2003 during normal Crawler/Transporter operations cracks were observed along the roller pad surfaces of several tread belt shoes. Further examination showed 20 cracked shoes on CT-1 and 40 cracked shoes on CT-2 and a formal failure analysis investigation was undertaken while the cracked shoes were replaced. Six shoes were cross-sectioned with the fracture surfaces exposed and it was determined that the cracks were due to fatigue that initiated on the internal casting web channels at pre-existing casting defects and propagated through thickness both transgranularly and intergranularly between internal shrinkage cavities, porosity, and along austenitic and ferritic grain boundaries. The original shoes were cast during the 1960's using a modified 861330 steel with slightly higher levels of chromium, nickel and molybdenum followed by heat treatment to achieve a minimum tensile strength of 11 Oksi. Subsequent metallurgical analysis of the tread belt shoes after multiple failures showed excessive internal defects, alloy segregation, a nonuniform ferritic/ bainitic/martensitic microstructure, and low average tensile properties indicative of poor casting and poor heat-treatment. As a result, NASA funded an initiative to replace all of the tread belt shoes on both crawler/transporters along with a redesign of the alloy, manufacturing, and heat-treatment to create a homogeneous cast structure with uniform mechanical and metallurgical properties. ME Global, a wholly owned subsidiary of ME Elecmetal based in Minneapolis, MN was selected as manufacturing and design partner to develop the new shoes and this paper describes the research, development, and manufacturing that resulted in the successful delivery of 1044 new Crawler/Transporter tread belt shoes all meeting rigid metallurgical and mechanical design criteria derived from finite element modeling of the stress loads required for safe space shuttle transport.

Parker, Donald S.↗
DOE OSTI2020

Magnesium Technology 2020

Magnesium and its alloys are being investigated widely for applications that require extraordinarily high strength-to-weight ratio, vibration damping, electromagnetic shielding, reduction in carbon footprint, sustainability improvements, and low toxicity. In the past decade or so, this drive has led to increased adoption of magnesium and its alloys in everyday products and it is no longer regarded as an esoteric material. The overarching goal of its widespread adoption and replacement of conventional materials such as steel and aluminum alloys has been restricted because of the cost of the material, limited sources of primary material, alloying constraints, high chemical reactivity, and challenges associated with its plasticity. Researchers, scientists, engineers, and economists from industry, government agencies and laboratories, and academic institutions alike are actively developing roadmaps for next-generation products and addressing these challenges as quickly as possible through unique and innovative methods. The TMS Magnesium Committee has been actively involved in providing a platform to these entities for disseminating the latest information, developments, and cutting-edge research and development, and showcasing the latest research and development trends related to magnesium and its alloys through the Magnesium Technology Symposium, which takes place every year at the TMS Annual Meeting. This proceedings volume retains the essence of this longstanding tradition. The twenty-first volume in the series, Magnesium Technology 2020, is the proceedings of the Magnesium Technology Symposium held during the 149th TMS Annual Meeting & Exhibition in San Diego, CA, February 23–27, 2020. The volume captures commentaries and papers from 15 different countries. The papers have been categorized systematically based on topics pertaining to magnesium production, casting and solidification, thermomechanical processing, deformation mechanisms, modeling, corrosion, and applications. The symposium began with keynote sessions that featured several distinguished invited speakers from government organizations and academia, who provided their perspectives on the state of the art, goals, and opportunities in magnesium alloy research and development. Dr. Carlos Tomé from Los Alamos National Laboratory, U.S. Department of Energy, discussed 3D characterization of mechanical twins across grain boundaries. This was followed by a talk on hierarchically structured ultrafine-grained magnesium alloys by Dr. Rajiv Mishra from the University of North Texas, USA, who presented an example of using friction stir additive manufacturing for implementing such microstructures at a component level. Dr. Mark Horstemeyer from Liberty University, USA, presented an overview of fatigue modeling to capture the corrosion-fatigue behavior of magnesium alloys. The final talk in this session was presented by Dr. Bin Jiang from Chongqing University, China, who presented a novel extrusion approach for achieving high-strength magnesium alloy plates.

Jordon, J. Brian↗
NASA NTRS1974

The effect of microstructure and strength on the fracture toughness of an 18 ni, 300 grade maraging steel

Methods for increasing the strength of maraging steels are discussed. An investigation was conducted to systematically vary the strength of 18 weight percent nickel, 300 grade maraging steel, to isolate any attending microstructural changes, and to study the effects of these changes on the fracture toughness of the alloy. A study aimed at determining the aging behavior of the program alloy was carried out to provide data by which to estimate yield strength. The effects of various alloying materials on the strength of the maraging steel are examined. The mechanical properties of the 300 grade maraging steel were determined by tension tests, fatigue precracked Charpy impact tests, and plane strain fracture toughness tests.

Psioda, J. A.↗
DOE OSTI2021

Understanding the efficacy of concentrated interstitial carbon in enhancing the pitting corrosion resistance of stainless steel

By introducing a high fraction of interstitial carbon through low temperature carburization, the pitting corrosion resistance of austenitic stainless steel can be significantly improved. Previous work attributed this to strengthening of the passive film by carbon. Here, however, we present a paradigm shift by showing that carbon actually weakens the passive film but strengthens the bonding within the alloy by forming localized (covalent) bonds with the metal atoms (Fe, Cr, Ni). Accordingly, the enhancement in pitting resistance is a result of carbon reducing the metal dissolution rate in a local pit environment by many orders of magnitude, which extremely decreases the growth stability of a pit and prevents it from transitioning into stable growth. Electronic structure calculations confirm that carbon bonds to the metal atoms and that the metal–carbon bonds are 1.4 to 2.0 times stronger than the metal–metal bonds. These results suggest a new strategy for the design of corrosion resistant alloys, namely surface engineering by infusion of concentrated interstitials that form strong bonds with the matrix atoms.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Connecting Dynamic Strain Aging to Deformation Processing in Magnesium-Calcium-Based Alloys

Fuel consumption can be improved by reducing car weight with substitution of aluminum and steel parts with magnesium (Mg). Magnesium formability at room temperature is limited due to strong basal texture generated prior processing. Shear band nucleation, observed under conditions in which dynamic strain aging (DSA), have been attributed to be responsible for texture weakening in dilute Mg – Rare Earths (RE) alloys. A low–cost substitution of RE is calcium (Ca) with similar atomic size. It is hypothesized that deformation of Mg – Ca alloys under DSA conditions improves Mg formability. In this study, Mg–Ca and Mg–Ca–Zn alloys were characterized using optical microscopy, XRD, and SEM/EDS. Compression testing was performed between 200 and 300C at different strain rates to observe DSA behavior. This work was performed under DOE Award Number DE-EE0007756.

Manuel, Michele↗
NASA NTRS1982

Ultimate intrinsic coercivity samarian-cobalt magnet. An Earth based feasibility study for Space Shuttle missions

Techniques for the electromagnetic containerless reaction of samarium with cobalt for the formation of samarium-cobalt alloys are summarized. The effort expended to reduce and instrument the oxygen partial pressure in the reaction chamber and coolant gas system are described as well as the experiments in which these improvements were shown to be partially effective. A stainless steel glove box capable of being evacuated to low 10 to the -6th torr pressure and refilled with ultra-pure argon was built and installed. Necessary accessories to perform SmCo5 powder preparation, compaction and subsequent encapsulation of the powder inside a hot isostatic pressing cannister were designed, built, and incorporated into the chamber. All accessories were tested for proper functioning inside the chamber. Using the facility, the first batch of densified SmCo5 powder was fabricated to near total density. Analysis of the densified compacts shows that oxygen contamination during fabrication was near zero.

Das, D.↗
NASA NTRS2012

Pressure Dome for High-Pressure Electrolyzer

A high-strength, low-weight pressure vessel dome was designed specifically to house a high-pressure [2,000 psi (approx. = 13.8 MPa)] electrolyzer. In operation, the dome is filled with an inert gas pressurized to roughly 100 psi (approx. = 690 kPa) above the high, balanced pressure product oxygen and hydrogen gas streams. The inert gas acts to reduce the clamping load on electrolyzer stack tie bolts since the dome pressure acting axially inward helps offset the outward axial forces from the stack gas pressure. Likewise, radial and circumferential stresses on electrolyzer frames are minimized. Because the dome is operated at a higher pressure than the electrolyzer product gas, any external electrolyzer leak prevents oxygen or hydrogen from leaking into the dome. Instead the affected stack gas stream pressure rises detectably, thereby enabling a system shutdown. All electrical and fluid connections to the stack are made inside the pressure dome and require special plumbing and electrical dome interfaces for this to be accomplished. Further benefits of the dome are that it can act as a containment shield in the unlikely event of a catastrophic failure. Studies indicate that, for a given active area (and hence, cell ID), frame outside diameter must become ever larger to support stresses at higher operating pressures. This can lead to a large footprint and increased costs associated with thicker and/or larger diameter end-plates, tie-rods, and the frames themselves. One solution is to employ rings that fit snugly around the frame. This complicates stack assembly and is sometimes difficult to achieve in practice, as its success is strongly dependent on frame and ring tolerances, gas pressure, and operating temperature. A pressure dome permits an otherwise low-pressure stack to operate at higher pressures without growing the electrolyzer hardware. The pressure dome consists of two machined segments. An O-ring is placed in an O-ring groove in the flange of the bottom segment and is trapped by the flange on the top dome segment when these components are bolted together with high-strength bolts. The pressure dome has several unique features. It is made (to ASME Pressure Vessel guidelines) in a high-strength aluminum alloy with the strength of stainless steel and the weight benefits of aluminum. The flange of the upper dome portion contains specially machined flats for mounting the dome, and other flats dedicated to the special feedthroughs for electrical connections. A pressure dome can be increased in length to house larger stacks (more cells) of the same diameter with the simple addition of a cylindrical segment. To aid in dome assembly, two stainless steel rings are employed. One is used beneath the heads of the high-strength bolts in lieu of individual hardened washers, and another is used instead of individual nuts. Like electrolyzers could be operated at low or high pressures simply by operating the electrolyzer outside or inside a pressurized dome.

Norman, Timothy↗
DOE OSTI2021

USAMP Low-Cost Mg Sheet Component Development and Demonstration Project

The overarching objective of this USAMP project was to develop and demonstrate door panels made from magnesium (Mg) sheet with a cost penalty over conventional steel stampings of no more than $\$5.50$/kg saved. The technical approach integrated experiments with advanced computational tools based on Integrated Computational Materials Engineering (ICME) methods to develop new alloy chemistries and their thermomechanical processing that promise improved formability and lower forming temperatures. A penultimate task before finally forming the stampings was to incorporate actual microstructure into models that would enable formability simulations. This approach would, for the first time, account for individual magnesium grains moving in an anisotropic fashion unlike that for aluminum or steel that have isotropic properties upon which the current simulation tools are based. In separate activities, new coatings and lubricants to facilitate forming and improved corrosion protection and joining strategies, were developed to ensure that the door could be produced with stated product requirements. A technical cost model, which included parts production, assembly, and paint for a door specifically designed for Mg sheet, showed the cost penalty to be between $\$4.26$ to $\$6.60$/kg saved, which enveloped the project’s cost targets. The cost of the coated Mg sheet was identified as the key driver for the cost penalty. The mass of the Mg-intensive door was 7.9 kg, which was 54% less than the baseline steel door.

36 MATERIALS SCIENCE↗