Search NASA⌕ Search

SEARCH · Search NASA

Results for “Leading Edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Pressure measurements on the leading edge of a swept wing at Mach 2.2

Detailed pressure measurements were made on a flat semispan swept wing with a rounded leading edge at Mach number 2.2 through a range of Reynolds numbers. Pressure orifices were distributed in the streamwise direction at five spanwise stations on the leading edge and on the upper and lower surfaces. No significant amount of leading-edge suction was found, but the pressures and integrated normal forces on the upper and lower surfaces indicate the presence of a vortex lift.

Sorrells, R. B., III↗
NASA NTRS2010

Fracture Mechanics Analyses of the Slip-Side Joggle Regions of Wing-Leading Edge Panels

The Space Shuttle Orbiter wing comprises of 22 leading edge panels on each side of the wing. These panels are part of the thermal protection system that protects the Orbiter wings from extreme heating that take place on the reentry in to the earth atmosphere. On some panels that experience extreme heating, liberation of silicon carbon (SiC) coating was observed on the slip side regions of the panels. Global structural and local fracture mechanics analyses were performed on these panels as a part of the root cause investigation of this coating liberation anomaly. The wing-leading-edge reinforced carbon-carbon (RCC) panels, Panel 9, T-seal 10, and Panel 10, are shown in Figure 1 and the progression of the stress analysis models is presented in Figure 2. The global structural analyses showed minimal interaction between adjacent panels and the T-seal that bridges the gap between the panels. A bounding uniform temperature is applied to a representative panel and the resulting stress distribution is examined. For this loading condition, the interlaminar normal stresses showed negligible variation in the chord direction and increased values in the vicinity of the slip-side joggle shoulder. As such, a representative span wise slice on the panel can be taken and the cross section can be analyzed using plane strain analysis.

Raju, Ivatury S.↗
NASA NTRS2006

Heat-Pipe-Cooled Leading Edges for Hypersonic Vehicles

Heat pipes can be used to effectively cool wing leading edges of hypersonic vehicles. . Heat-pipe leading edge development. Design validation heat pipe testing confirmed design. Three heat pipes embedded and tested in C/C. Single J-tube heat pipe fabricated and testing initiated. HPCLE work is currently underway at several locations.

Glass, David E.↗
NASA NTRS1985

An Attached Flow Design of a Noninterferring Leading Edge Extension to a Thick Delta Wing

An analytical procedure for the determination of the shape of a Leading-Edge Extension (LEE) which satisfies design criteria, including especially noninterference at the wing design point, has been developed for thick delta wings. The LEE device best satisfying all criteria is designed to be mounted on a wing along a dividing stream surface associated with an attached flow design lift coefficient (C L,d ) of greater than zero. This device is intended to improve the aerodynamic performance of transonic aircraft at C L greater than C L,d system emanating from the LEE leading edge. In order to quantify this process a twisted and cambered thick delta wing was chosen for the initial application of this design procedure. Appropriate computer codes representing potential and vortex flows were employed to determine the dividing stream surface at C L,d and an optimized LEE planform shape at C L greater than C L,d , respectively. To aid in the LEE selection, the aerodynamic effectiveness of 36 planforms was investigated at C L greater than C L,d . This study showed that reducing the span of the candidate LEEs has the most detrimental effect on overall aerodynamic efficiency, regardless of the shape or area. Furthermore, for a fixed area, constant-chord LEE candidates were relatively more efficient than those with sweep less than the wing. At C L,d , the presence of the LEE planform best satisfying the design criteria was found to have no effect on the wing alone aerodynamic performance.

Leading edge extension↗
NASA NTRS1993

Application of a flush airdata sensing system to a wing leading edge (LE-FADS)

This paper investigates the feasibility of locating a flush air-data sensing (FADS) system on a wing leading edge where the operation of the avionics or fire control radar system will not be hindered. The leading-edge FADS system (LE-FADS) was installed on an unswept symmetrical airfoil, and a series of low-speed wind-tunnel tests were conducted to evaluate the performance of the system. As a result of the tests it is concluded that the aerodynamic models formulated for use on aircraft nosetips are directly applicable to wing leading edges and that the calibration process is similar. Furthermore, the agreement between the air-data calculations for angle of attack and total pressure from the LE-FADS and known wind-tunnel values suggest that wing-based flush air-data systems can be calibrated to a high degree of accuracy. Static wind-tunnel tests for angles of attack from -50 to 50 deg and dynamic pressures from 3.6 to 11.4 lb/sq ft were performed.

Whitmore, Stephen A.↗
NASA NTRS1991

Computational studies of a fluid spike as a leading edge protection device for shock-shock interference heating

The effectiveness of a fluid spike as a device to protect leading edges of hypersonic atmospheric flight vehicles from high aerothermal loads produced by complex shock-shock interference is studied. The two-dimensional Navier-Stokes equations are solved using an unstructured cell-centered, fully implicit, flux-difference split algorithm. Adaptively generated unstructured meshes are employed. A type IV shock-shock interference for Mach 8 flow on a cylindrical leading edge with and without a small contraflow supersonic jet (fluid spike) placed at two different locations on the body is solved. A typical flow past a blunt body with a type IV shock-shock interference produces very high pressures and heat fluxes on the leading edge. Present results indicate that a fluid spike displaces the bow shock further in front of the body and modifies the shock-shock interference pattern. This leads to reduced peak pressures and heat fluxes on the body.

Prabhu, Ramadas K.↗
NASA NTRS1985

Effect of leading-edge load constraints on the design and performance of supersonic wings

A theoretical and experimental investigation was conducted to assess the effect of leading-edge load constraints on supersonic wing design and performance. In the effort to delay flow separation and the formation of leading-edge vortices, two constrained, linear-theory optimization approaches were used to limit the loadings on the leading edge of a variable-sweep planform design. Experimental force and moment tests were made on two constrained camber wings, a flat uncambered wing, and an optimum design with no constraints. Results indicate that vortex strength and separation regions were mildest on the severely and moderately constrained wings.

Darden, C. M.↗
NASA NTRS1981

Effectiveness of leading-edge vortex flaps on 60 and 75 degree delta wings

A series of wind tunnel tests were run on 60 and 75 deg sweep delta wings to examine the effectiveness of leading-edge vortex flaps. Tests results showed that leading-edge vortex flaps are effective in giving large increases in lift-to-drag ratio and decreases in drag over a wide range of angle of attack. Tests on inverted flaps on the 60 deg delta wing showed substantial increases in lift and drag and may indicate a possibility of using inverted flaps on delta wings in the landing portion of flight. The 60 deg data were compared with that for a 75 deg sweep delta wing confirming that leading-edge vortex flap effectiveness is stronger as sweep is increased. Pitching moment effects due to vortex flaps use were also examined.

Marchman, J. F., III↗
NASA NTRS1961

Transonic Investigation of Aerodynamic Characteristics of a Swept-Wing Fighter-Airplane Model with Leading-Edge Droop in Combination with Outboard Chord-Extensions and Notches

An investigation of the effects of several wing leading-edge modifications on the aerodynamic characteristics of a 45 degree swept-wing fighter-airplane model has been conducted in the Langley 16-foot transonic tunnel at low and high lifting conditions at Mach numbers from 0.85 to 1.03. The investigation included the determination of the effect on longitudinal stability and performance characteristics of wing leading-edge and chord-extension droops of 60 and 20 degrees chord-extension overhangs of 0.075c and 0.15c (where c inboard end of the 0.075c chord-extension to depths of 0.075c and 0.l25c, and indention of the model fuselage to conform partially to the supersonic area rule for a Mach number of 1.20. Lift, drag, and pitching-moment data were obtained for configurations with the tail on and off. Comparisons of data obtained from the present model with data from a configuration with leading-edge slats are included. Generally, the model wing modifications provided only slight improvements of the airplane longitudinal stability characteristics, but did substantially reduce the airplane drag coefficients at moderate and high lifting conditions.

Whitcomb, Charles F.↗
NASA NTRS1959

Influence of Large Positive Dihedral on Heat Transfer to Leading Edges of Highly Swept Wings at Very High Mach Numbers

A geometric study has been made of some of the effects of dihedral on the heat transfer to swept delta wings. The results of this study show that the incorporation of large positive dihedral on highly swept wings can shift, even at moderately low angles of attack, the stagnation-line heat-transfer problem from the leading edges to the axis of symmetry (ridge line). An order-of-magnitude analysis (assuming laminar flow) indicates conditions for which it may be possible to reduce the heating at the ridge line (except in the vicinity of the wing apex) to a small fraction of the leading-edge heat transfer of a flat wing at the same lift. Furthermore, conditions are indicated where dihedral reduces the leading-edge heat transfer for angles of attack less than those required to shift the stagnation line from the leading edge to the ridge line.

Cooper, Morton↗
NASA NTRS2016

Effects of Alternate Leading Edge Cutback on the Space Shuttle Main Engine Low Pressure Fuel Pump

A higher order cavitation oscillation observed in the SSME low pressure fuel pump has been eliminated in water flow testing of a modified subscale replica of the inducer. The low pressure pump was modified by removing the outboard sections of two opposing blades of the four-bladed inducer, blending the "cutback" regions into the blades at the leading edge and tip, and removing material on the suction sides to decrease the exposed leading edge thickness. The leading edge tips of the cutback blades were moved approximately 25 degrees from their previous locations, thereby increasing one blade to blade spacing, decreasing the second, while simultaneously moving the cutback tips downstream. The test was conducted in MSFC's inducer test loop at scaled operating conditions in degassed and filtered water. In addition to eliminating HOC across the entire scaled operating regime, rotating cavitation was suppressed while the range of both alternate blade and asymmetric cavitation were increased. These latter phenomena, and more significantly, the shifts between these cavitation modes also resulted in significant changes to the head coefficient at low cavitation numbers. Reverse flow was detected at a slightly larger flow coefficient with the cutback inducer and suction capability was reduced by approximately 1 velocity head at and above approximately 90% of the reference flow coefficient. These performance changes along with more intense reverse flow are consistent with poor flow area management and increased incidence in the cutback region. Although the test demonstrated that the inducer modification was successful at eliminating the higher order cavitation across the entire scaled operating regime, different, previously unobserved, cavitation oscillations were introduced and significant performance penalties were imposed.

Mulder, Andrew↗
NASA NTRS1975

Preservation of wing leading edge suction at the plane of symmetry as a factor in wing-fuselage design

Most fuselage geometries cover a portion of the wing leading edge near the plane of symmetry, and it seems reasonable to expect that a large fraction of the leading edge suction which would be developed by the covered wing at high angles of attack is not developed on the fuselage. This is one of the reasons that the Oswald span efficiency factor for the wing body combination fails to approach the value predicted by lifting line theory for the isolated wing. Some traditional and recent literature on wing-body interference is discussed and high Reynolds number data on wing-body-nacelle drag are reviewed. An exposed central leading edge geometry has been developed for a sailplane configuration. Low Reynolds number tests have not validated the design concept.

Larrabee, E. E.↗
NASA NTRS1981

Mass loss of TEOS-coated RCC subjected to the environment at the shuttle wing leading edge

Coated, reinforced carbon-carbon (RCC) is used for the leading edges of the Space Shuttle. The mass loss characteristics of RCC specimens coated with tetra-ethyl-ortho-silicate (TEOS) were determined for conditions which simulated the entry environment expected at the stagnation area of the wing leading edge. Maximum specimen temperature was 1632 K. Specimens were exposed for up to 100 missions. Stress levels up to 8.274 MPa caused an average increase in oxidation of 6 percent over unstressed specimens. Experimentally determined mass losses were compared with those predicted by an existing empirical analysis.

Stroud, C. W.↗
NASA NTRS1992

Leading edge sweep effects in generic three-dimensional sidewall compression scramjet inlets

A computational and experimental study of generic 3D sidewall compression inlets is conducted to examine the effects of fore and aft leading edge sweep on the internal shock structure. Inlets with leading edge sweeps of +30 deg and -30 deg with sidewall compression angles of 6 deg were tested in the NASA Langley Mach 4 air tunnel at a geometric contraction ratio of 1.87. The principal difference in performance was determined to be in the mass capture. Spillage was identified as having two components: a pressure induced component and a sweep induced component. It was found that while the direction of the leading edge sweep had a large influence on the spillage, the pressure effects were more important.

Cozart, Aaron B.↗
NASA NTRS1979

Leading-edge slat optimization for maximum airfoil lift

A numerical procedure for determining the position (horizontal location, vertical location, and deflection) of a leading edge slat that maximizes the lift of multielement airfoils is presented. The structure of the flow field is calculated by iteratively coupling potential flow and boundary layer analysis. This aerodynamic calculation is combined with a constrained function minimization analysis to determine the position of a leading edge slat so that the suction peak on the nose of the main airfoil is minized. The slat position is constrained by the numerical procedure to ensure an attached boundary layer on the upper surface of the slat and to ensure negligible interaction between the slat wake and the boundary layer on the upper surface of the main airfoil. The highest angle attack at which this optimized slat position can maintain attached flow on the main airfoil defines the optimum slat position for maximum lift. The design method is demonstrated for an airfoil equipped with a leading-edge slat and a trailing edge, single-slotted flap. The theoretical results are compared with experimental data, obtained in the Ames 40 by 80 Foot Wind Tunnel, to verify experimentally the predicted slat position for maximum lift. The experimentally optimized slat position is in good agreement with the theoretical prediction, indicating that the theoretical procedure is a feasible design method.

Olson, L. E.↗
NASA NTRS1983

Experimental study of wing leading-edge devices for improved maneuver performance of a supercritical maneuvering fighter configuration

Wind tunnel tests were conducted to examine the use of wing leading-edge devices for improved subsonic and transonic maneuver performance. These devices were tested on a fighter configuration which utilized supercritical-wing technology. The configuration had a leading-edge sweep of 45 deg and an aspect ratio of 3.28. The tests were conducted at Mach numbers of 0.60 and 0.85 with angles of attack from -0.5 deg to 22 deg. At both Mach numbers, sharp leading-edge flaps produced vortices which greatly altered the flow pattern on the wing and resulted in substantial reductions in drag at high lift. Underwing or pylon-type vortex generators also reduced drag at high lift. The vortex generators worked better at a Mach number of 0.60. The vortex generators gave the best overall results with zero toe-in angle and when mounted on either the outboard part of the wing or at both an outboard location and halfway out the semispan. Both the flaps and the vortex generators had a minor effect on the pitching moment. Fluorescent minitufts were found to be useful for flow visualization at transonic maneuver conditions.

Mann, M. J.↗
NASA NTRS1987

Vortex interaction with a leading-edge of finite thickness

Vortex interaction with a thick elliptical leading-edge at zero relative offset produces a pronounced secondary vortes of opposite sense that travels with the same phase speed as the primaty vortex along the lower surface of the edge. The edge thickness (scale) relative to the incident vorticity field has a strong effect on the distortion of the incident primary vortex during the impingement processs. When the thickness is sufficiently small, there is a definite severing of the incident vortex and the portion of the incident vortex that travels along the upper part of the elliptical surface has a considerably larger phase speed than that along the lower surface; this suggests that the integrated loading along the upper surface is more strongly correlated. When the thickness becomes too large, then most, if not all, of the incident vortex passes below the leading-edge. On the other hand, the relative tranverse offset of the edge with respect to the center of the incident vortex has a significant effect on the secondary vortex formation.

Sohn, D.↗