Search NASA⌕ Search

SEARCH · Search NASA

Results for “MACH NUMBER EFFECTS - COMPLETE WINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Effects at Mach Numbers of 1.61 and 2.01 of Camber and Twist on the Aerodynamic Characteristics of Three Swept Wings Having the Same Planform

An investigation has been made at Mach numbers of 1.61 and 2.01 to determine the aerodynamic characteristics of three wings having a sweepback of 50 deg at the quarter-chord line, a taper ratio of 0.20, an NACA 65A005 thickness distribution, and an aspect ratio of 3.5. One wing was flat, one had at each spanwise station an a = 0 mean line modified to have a maximum height of 4-percent chord, and one had a linear variation of twist with 6 deg of washout at the tip. Tests were made with natural and fixed transition at Reynolds numbers ranging from 1.2 x 10(exp 6) to 3.6 x 10(exp 6) through an angle-of-attack range of -20 deg to 20 deg. When compared with the flat wing, the effect of the linear variation of twist with 6 deg of washout at the tip was to increase the lift-drag ratio when the leading edge was subsonic; but little increase in lift-drag ratio was obtained when the leading edge was supersonic. Pitching moment was increased and gave a positive trim point without greatly affecting the rate of change of pitching moment with lift coefficient. For the cambered wing the high minimum drag resulted in comparatively low lift-drag ratios. In addition, the pitching moments were decreased so that a negative trim point was obtained.

Landrum, Emma Jean↗
NASA NTRS1975

Effect of wing planform and canard location and geometry on the longitudinal aerodynamic characteristics of a close-coupled canard wing model at subsonic speeds

A generalized wind-tunnel model with canard and wing planforms typical of highly maneuverable aircraft was tested in the Langley 7- by 10-foot high-speed tunnel at a Mach number of 0.30 to determine the effect of canard location, canard size, wing sweep, and canard strake on canard-wing interference to high angles of attack. The major results of this investigation may be summarized as follows: the high-canard configuration (excluding the canard strake and canard flap), for both the 60 deg and 44 deg swept leading-edge wings, produced the highest maximum lift coefficient and the most linear pitching-moment curves; substantially larger gains in the canard lift and total lift were obtained by adding a strake to the canard located below the wing chord plane rather than by adding a strake to the canard located above the wing chord plane.

Gloss, B. B.↗
NASA NTRS1976

Effect of Reynolds number on the aerodynamic stability and control characteristics of a 55 deg clipped-delta-wing orbiter configuration at supersonic Mach numbers

A wind-tunnel investigation has been conducted at Mach numbers from 1.60 to 4.63 for Reynolds numbers varying from approximately 0.8 million to 10.0 million (based on body length) to determine the Reynolds number effects on the static longitudinal and lateral aerodynamic stability and control characteristics of two scale models of the Grumman H-33 space shuttle orbiter. The results indicate that for the Reynolds number range investigated, there are no Reynolds number effects on the longitudinal or lateral aerodynamic characteristics of either model with zero control deflections and only negligible effects with control deflections. The roll control is constant for both models with the possible exception of a slight increase with increases in Reynolds number up to 2.0 million at the lower Mach numbers. This very small Reynolds number effect is much more apparent for the smaller model and disappears with increasing Mach and Reynolds numbers.

Blair, A. B., Jr.↗
NASA NTRS1972

Effects of Reynolds number and body corner radius on aerodynamic characteristics of a space shuttle-type vehicle at subsonic Mach numbers

Static aerodynamic forces and moments were measured to study the effects of Reynolds number and body corner radius on the aerodynamic characteristics of a straight wing space shuttle orbiter at subsonic speeds. A 0.02-scale model was tested at Mach numbers from 0.3 to 0.9 and Reynolds numbers from about 600,000 to 3 million, based on body width. The body alone and the body with its wing and horizontal tail attached were tested at angles of attack from 35 to 75 degrees. The effects of rounding the body corners at the junctures connecting the bottom and sides were investigated for corner radii from 0 to 8.5 percent of the body width. At low subsonic Mach numbers (free stream Mach number approximately equal 0.3) the aerodynamic characteristics are affected significantly by changes in Reynolds number and body corner radius. With increase in Mach number to free stream Mach number = 0.9 the effect of Reynolds number seems to vanish, but a significant effect of body corner radius remains.

Jorgensen, L. H.↗
NASA NTRS1948

Preliminary Results of an Investigation by the Wing-Flow Method of the Longitudinal Stability Characteristics of a 1/50-Scale Semispan Model of the McDonnell XP-88 Airplane

This paper presents the results of measurements of longitudinal stability of a 1/50-scale model of the XP-88 airplane by the wing-flow method. Lift, rolling-moment, hinge-moment, and pitching-moment characteristics as well as the downwash at the tail were measured over a Mach number range from approximately 0.5 to 1.05 at Reynolds numbers below 1,000,000. No measurements of drag were obtained. No abrupt changes due to Mach number were noted in any of the parameters measured. The data indicated that the wing was subject to early tip stalling; that the tail effectiveness decreased gradually with increasing Mach number up to M = 0.9, but increased again at higher Mach numbers; that the variation of downwash with angle of attack did not change appreciably with Mach number except between 0.95 and 1.0 where d(epsilon)/d(alpha), decreased from 0.46 to 0.32; that at zero lift with a stabilizer setting of -1.5 deg there was a gradually increasing nosing-up tendency with increasing Mach number; and that the control-fixed stability in maneuvers at constant speed gradually increased with increasing Mach number.

Crane, Harold L.↗
NASA NTRS1956

The Interference Effects of a Body on the Spanwise Load Distributions of Two 45 Degree Sweptback Wings of Aspect Ratio 8.02 from Low-Speed Tests

Tests of two wing-body combinations have been conducted in the Langley 19-foot pressure tunnel at a Reynolds number of 4 x 10(exp 6) and a Mach number of 0.19 to determine the effects of the bodies on the wing span load distributions. The wings had 45 degrees sweepback of the quarter-chord line, aspect ratio 8.02, taper ratio 0.45, and incorporated 12-percent-thick airfoil sections streamwise. One wing was untwisted and uncambered whereas the second wing incorporated both twist and camber. Identical bodies of revolution, of 10:1 fineness ratio, having diameter-to-span ratios of 0.10, were mounted in mid-high-wing arrangements. The effects of wind incidence, wing fences, and flap deflection were determined for the plane uncambered wing. The addition of the body to the plane wing increased the exposed wing loading at a given lift coefficient as much as 10 percent with the body at 0 degrees incidence and 4 percent at 4 degrees incidence. The bending-moment coefficients at the wing-body juncture were increased about 2 percent with the body at 0 degrees incidence, whereas the increases were as much as 10 percent with the body at 4 degrees incidence. The spanwise load distributions due to the body on the plane wing as calculated by using a swept-wing method employing 19 spanwise lifting elements and control points generally showed satisfactory agreement with experiment. The spanwise load distributions due to body on the flapped plane wing and on the twisted and cambered wing were dissimilar to those obtained on the plane wing. Neither of the methods of calculation which were employed yielded distributions that agreed consistently with experiment for either the flapped plane wing or the twisted and cambered wing.

Martina, Albert P.↗
NASA NTRS1994

An experimental and theoretical study of the aerodynamic characteristics of some generic missile concepts at Mach numbers from 2 to 6.8

A study has been made of the experimental and theoretical aerodynamic characteristics for some generic high-speed missile concepts at Mach numbers from 2 to 6.8. The basic body for this study had a length-to-diameter ratio of 10 with the forward half being a modified blunted ogive and the rear half being a cylinder. Modifications made to the basic body included the addition of an after body flare, the addition of highly swept cruciform wings and the addition of highly swept aft tails. The effects of some controls were also investigated with all-moving wing controls on the flared body and trailing-edge flap controls on the winged body. The results indicated that the addition of a flare, wings, or tails to the basic body all provided static longitudinal stability with varying amounts of increased axial force. The control arrangements were effective in producing increments of normal-force and pitching-moment at the lower Mach numbers. At the highest Mach number, the flap control on the winged body was ineffective in producing normal-force or pitching-moment but the all-moving wing control on the flared body, while losing pitch effectiveness, still provided normal-force increments. Calculated results obtained through the use of hypersonic impact theory were in generally good agreement with experiment at the higher Mach numbers but were not accurate at the lower Mach numbers.

Spearman, M. Leroy↗
NASA NTRS1975

The effects on propulsion-induced aerodynamic forces of vectoring a partial-span rectangular jet at Mach numbers from 0.40 to 1.20

An investigation was conducted in the Langley 16-foot transonic tunnel to determine the induced lift characteristics of a vectored thrust concept in which a rectangular jet exhaust nozzle was located in the fuselage at the wing trailing edge. The effects of nozzle deflection angles of 0 deg to 45 deg were studied at Mach numbers from 0.4 to 1.2, at angles of attack up to 14 deg, and with thrust coefficients up to 0.35. Separate force balances were used to determine total aerodynamic and thrust forces as well as thrust forces which allowed a direct measurement of jet turning angle at forward speeds. Wing pressure loading and flow characteristics using oil flow techniques were also studied.

Capone, F. J.↗
NASA NTRS1976

Experimental effects of fuselage camber on longitudinal aerodynamic characteristics of a series of wing-fuselage configurations at a Mach number of 1.41

An experimental investigation was conducted to evaluate a method for the integration of a fighter-type fuselage with a theoretical wing to preserve desirable wing aerodynamic characteristics for efficient maneuvering. The investigation was conducted by using semispan wing fuselage models mounted on a splitter plate. The models were tested through an angle of attack range at a Mach number of 1.41. The wing had a leading edge sweep angle of 50 deg and an aspect ratio of 2.76; the wing camber surface was designed for minimum drag due to lift and was to be self trimming at a lift coefficient of 0.2 and at a Mach number of 1.40. A series of five fuselages of various camber was tested on the wing.

Dollyhigh, S. M.↗