Search NASA⌕ Search

SEARCH · Search NASA

Results for “MOLDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

An improved compression molding technology for continuous fiber reinforced composite laminate. Part 1: AS-4/LaRC-TPI 1500 (HFG) Prepreg system

Poor processability of fiber reinforced high performance polyimide thermoplastic resin composites is a well recognized issue which, in many cases, prohibits the fabrication of composite parts with satisfactorily consolidated quality. Without modifying the resin matrix chemistry, improved compression modeling procedures were proposed and investigated with the AS-4/LaRC-TPI 1500 High Flow Grade (HFG) prepreg system. Composite panels with excellent C-scans can be consistently molded by this method under 700 F and a consolidation pressure as low as 100 psi. A mechanism for the consolidation of the composite under this improved molding technique is discussed. This mechanism reveals that a certain degree of matrix shear and tow filament slippage and nesting between plies occur during consolidation, which leads to a reduction of the consolidating pressure necessary to offset the otherwise intimate inter fiber-fiber contact and consequently achieves a better consolidation quality. Outstanding short beam shear strength and flexural strength were obtained from the molded panels. A prolonged consolidation step under low pressure, i.e., 100 psi at 700 F for 75 minutes, was found to significantly enhance the composite mechanical properties.

Hou, Tan-Hung↗

Flow behavior in liquid molding

The liquid molding (LM) process for manufacturing polymer composites with structural properties has the potential to significantly lower fabrication costs and increase production rates. LM includes both resin transfer molding and structural reaction injection molding. To achieve this potential, however, the underlying science base must be improved to facilitate effective process optimization and implementation of on-line process control. The National Institute of Standards and Technology (NIST) has a major program in LM that includes materials characterization, process simulation models, on-line process monitoring and control, and the fabrication of test specimens. The results of this program are applied to real parts through cooperative projects with industry. The key feature in the effort is a comprehensive and integrated approach to the processing science aspects of LM. This paper briefly outlines the NIST program and uses several examples to illustrate the work.

Hunston, D.↗

Method for molding structural parts utilizing modified silicone rubber

This invention improves upon a method for molding structural parts from preform material. Preform material to be used for the part is provided. A silicone rubber composition containing entrained air voids is prepared. The silicone rubber and preform material assembly is situated within a rigid mold cavity used to shape the preform material to the desired shape. The entire assembly is heated in a standard heating device so that the thermal expansion on the silicone rubber exerts the pressure necessary to force the preform material into contact with the mold container. The introduction of discrete air voids into the silicone rubber allows for accurately controlled pressure application on the preform material at the cure temperature.

Weisner, Erik S.↗

Verification of a three-dimensional resin transfer molding process simulation model

Experimental evidence was obtained to complete the verification of the parameters needed for input to a three-dimensional finite element model simulating the resin flow and cure through an orthotropic fabric preform. The material characterizations completed include resin kinetics and viscosity models, as well as preform permeability and compaction models. The steady-state and advancing front permeability measurement methods are compared. The results indicate that both methods yield similar permeabilities for a plain weave, bi-axial fiberglass fabric. Also, a method to determine principal directions and permeabilities is discussed and results are shown for a multi-axial warp knit preform. The flow of resin through a blade-stiffened preform was modeled and experiments were completed to verify the results. The predicted inlet pressure was approximately 65% of the measured value. A parametric study was performed to explain differences in measured and predicted flow front advancement and inlet pressures. Furthermore, PR-500 epoxy resin/IM7 8HS carbon fabric flat panels were fabricated by the Resin Transfer Molding process. Tests were completed utilizing both perimeter injection and center-port injection as resin inlet boundary conditions. The mold was instrumented with FDEMS sensors, pressure transducers, and thermocouples to monitor the process conditions. Results include a comparison of predicted and measured inlet pressures and flow front position. For the perimeter injection case, the measured inlet pressure and flow front results compared well to the predicted results. The results of the center-port injection case showed that the predicted inlet pressure was approximately 50% of the measured inlet pressure. Also, measured flow front position data did not agree well with the predicted results. Possible reasons for error include fiber deformation at the resin inlet and a lag in FDEMS sensor wet-out due to low mold pressures.

Fingerson, John C.↗

Method for Molding Structural Parts Utilizing Modified Silicone Rubber

This invention improves upon a method for molding structural parts from preform material. Preform material to be used for the part is provided. A silicone rubber composition containing entrained air voids is prepared. The silicone rubber and preform material assembly is situated within a rigid mold cavity used to shape the preform material to die desired shape. The entire assembly is heated in a standard heating device so that the thermal expansion of the silicone rubber exerts the pressure necessary to force the preform material into contact with the mold container. The introduction of discrete air voids into the silicone rubber allows for accurately controlled pressure application on the preform material at the cure temperature.

Weiser, Erik S.↗

Molded Magnetic Article

A molded magnetic article and fabrication method are provided. Particles of ferromagnetic material embedded in a polymer binder are molded under heat and pressure into a geometric shape. Each particle is an oblate spheroid having a radius-to-thickness aspect ratio approximately in the range of 15-30. Each oblate spheroid has flattened poles that are substantially in perpendicular alignment to a direction of the molding pressure throughout the geometric shape.

Bryant, Robert G.↗

Fabrication of Molded Magnetic Article

A molded magnetic article and fabrication method are provided. Particles of ferromagnetic material embedded in a polymer binder are molded under heat and pressure into a geometric shape. Each particle is an oblate spheroid having a radius-to-thickness aspect ratio approximately in the range of 15-30. Each oblate spheroid has flattened poles that are substantially in perpendicular alignment to a direction of the molding pressure throughout the geometric shape.

Robert G Bryant↗

Polyimide Composites Properties of RTM370 Fabricated by Vacuum Assisted Resins Transfer Molding (VARTM)

RTM370 imide resin based on 2,3,3 ,4 -biphenyl dianhydride ( a-BPDA), 3,4 -oxydianinline (3,4 -ODA) with 4-phenylethynylphthalic (PEPA) endcap has shown to exhibit high Tg (370 C) and low melt viscosity (10-30 poise) at 280 C with a pot-life of 1-2 h. Previously, RTM370 resin has been fabricated into composites with T650-35 carbon fabrics by resin transfer molding (RTM) successfully. RTM370 composites exhibit excellent mechanical properties up to 327 C (620 F), and outstanding property retention after aging at 288 C (550 F) for 1000 hrs. In this presentation, RTM 370 composites will be fabricated by vacuum assisted resins transfer molding (VARTM), using vacuum bags without mold. The mechanical properties of RTM370 composites fabricated by VARTM will be compared to those of RTM370 made by RTM.

Chuang, Kathy C.↗

Ground Testing of the EMCS Seed Cassette for Biocompatibility with the Cellular Slime Mold, Dictyostelium Discoideum

The European Modular Cultivation System, EMCS, was developed by ESA for plant experiments. To expand the use of flight verified hardware for various model organisms, we performed ground experiments to determine whether ARC EMCS Seed Cassettes could be adapted for use with cellular slime mold for future space flight experiments. Dictyostelium is a cellular slime mold that can exist both as a single-celled independent organism and as a part of a multicellular colony which functions as a unit (pseudoplasmodium). Under certain stress conditions, individual amoebae will aggregate to form multicellular structures. Developmental pathways are very similar to those found in Eukaryotic organisms, making this a uniquely interesting organism for use in genetic studies. Dictyostelium has been used as a genetic model organism for prior space flight experiments. Due to the formation of spores that are resistant to unfavorable conditions such as desiccation, Dictyostelium is also a good candidate for use in the EMCS Seed Cassettes. The growth substratum in the cassettes is a gridded polyether sulfone (PES) membrane. A blotter beneath the PES membranes contains dried growth medium. The goals of this study were to (1) verify that Dictyostelium are capable of normal growth and development on PES membranes, (2) develop a method for dehydration of Dictyostelium spores with successful recovery and development after rehydration, and (3) successful mock rehydration experiments in cassettes. Our results show normal developmental progression in two strains of Dictyostelium discoideum on PES membranes with a bacterial food source. We have successfully performed a mock rehydration of spores with developmental progression from aggregation to slug formation, and production of morphologically normal spores within 9 days of rehydration. Our results indicate that experiments on the ISS using the slime mold, Dictyostelium discoideum could potentially be performed in the flight verified hardware of the EMCS ARC Seed Cassettes.

biocompatibility↗

PERFORMANCE ENHANCEMENT OF COMPRESSION MOLDED KENAF FIBER REINFORCED VINYL ESTER COMPOSITES THROUGH RESIN ADDITIVE

Plant-based bio-fiber has the potential to achieve weight and cost savings over glass fiber in automotive polymer composites if moisture stability and fiber-resin compatibility issues can be solved. This paper describes the compression molding of 50vol% 2 inch random nonwoven mat kenaf fiber vinyl ester composites with and without chemical resin additives intended to improve moisture stability and resin compatibility. The 2wt% addition of n-undecanoyl chloride or 10-undecenoyl chloride to the styrene-based resin prior to molding of the kenaf composites was observed to decrease the 24hr, 25oC moisture uptake of the molded panels by more than 50%. The tensile stiffness and flexural stiffness of the soaked panels containing these additives were seen to increase by more than 30% and 70%, respectively, relative to panels made with no additives. While ‘dry’ panel (50% relative humidity at 25oC) strengths did not significantly change in the presence of the additives, tensile strength was observed to increase by more than 40% and flexural strength more than doubled for the soaked panels.

Environmental Molecular Sciences Laboratory↗

High rate fabrication of compression molded components

A method for fabricating a thermoplastic composite component comprises inductively heating a thermoplastic pre-form with a first induction coil by inducing current to flow in susceptor wires disposed throughout the pre-form, inductively heating smart susceptors in a molding tool to a leveling temperature with a second induction coil by applying a high-strength magnetic field having a magnetic flux that passes through surfaces of the smart susceptors, shaping the magnetic flux that passes through surfaces of the smart susceptors to flow substantially parallel to a molding surface of the smart susceptors, placing the heated pre-form between the heated smart susceptors; and applying molding pressure to the pre-form to form the composite component.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Fabrication of layer-by-layer photonic crystals using two polymer microtransfer molding

A method of manufacturing photonic band gap structures operable in the optical spectrum has been presented. The method comprises the steps of filling a plurality of grooves of an elastomeric mold with a UV curable first polymer, each groove in parallel with each other and partially curing the first polymer. A second polymer is coated on the first polymer. A substrate or a multi-layer polymer structure is placed on the filled mold and the resulting structure is exposed to UV light (i.e., is UV cured). The mold is peeled away from the first and second polymers such that a layer of polymer rods is formed on the substrate/multi-layer polymer structure. The process is repeated until a desired number of layers have been formed. The multi-layer structure can be used to create ceramic and metallic photonic band gaps by infiltration, electro-deposition, and/or metal coating.

36 MATERIALS SCIENCE↗

HYBRID MANUFACTURING TECHNIQUE USING LARGE-SCALE ADDITIVE MANUFACTURING AND COMPRESSION MOLDING FOR HIGH PERFORMANCE COMPOSITES

Additive Manufacturing (AM) or 3-D printing has moved from small-scale prototypes to large-scale functional structures. With the introduction of large-scale 3D printers into the market a new industry has been born. For the first time, we are presenting the idea of preparing large-scale 3-D printed β-stage preforms to be used in traditional compression molding (CM) manufacturing technique to prepare final functional structures. Short carbon fiber (CF) reinforced material acrylonitrile butadiene Styrene i.e. ABS with 20% CF is used in present work. It is shown that highly aligned 3D printed short carbon fiber composite maintains its orientation after compression molding. A sandwich panel is prepared to show the capability to prepare complicated parts by integrating AM and CM. Interphase of the prepared dissimilar material is also studied using SEM. Samples prepared using AM-CM integration showed 11% and 79 % improvement in tensile strength and tensile modulus respectively compared to the traditional extrusion compression molding (ECM) process.

Kumar, Vipin↗

MODELLING FIBER ORIENTATION DURING ADDITIVE MANUFACTURING COMPRESSION MOLDING PROCESSES

The production of high-performance thermoplastic composites reinforced with short carbon fibers can be achieved by a novel “additive manufacturing-compression molding” technique. An advantage of such combination is two-fold: controlled fiber orientation in additive manufacturing and less void content by compression molding. In this study, a computational fluid dynamics model has been developed to predict the behavior of printed layers during fiber-reinforced thermoplastic extrusion and subsequent compression molding. The fiber orientation was modelled with a simple quadratic closure model. The interaction between the fibers is included using a rotary diffusion coefficient which becomes significant in concentrated regimes. Finally, the second order orientation tensor is coupled with the momentum equation as an anisotropic part of the stress term. The effect of processing parameters on the behavior of printed layers was investigated to determine the favorable printing scenarios. The developed numerical model enables design of high-performance composites with tunable mechanical properties.

Seta, Berin↗

MODELLING OF ADDITIVE MANUFACTURING – COMPRESSION MOLDING PROCESS USING COMPUTATIONAL FLUID DYNAMICS

A computational fluid dynamics model has been developed to predict the behavior of a printed strands during a novel material extrusion additive manufacturing and compression molding process. While the traditional additive manufacturing process enables control over the fiber orientation within the part, it would also result in high void content. On the other hand, compression molding produces parts with low porosity levels at rapid processing cycle time but lacks control over the microstructure. The novel additive manufacturing – compression molding (AM-CM) integrating both these processes offers control over both the microstructure and porosity to manufacturing high performance composite parts. The numerical model developed here enables to analyze the effect of processing parameters on the behaviour of printed layer that is subsequently compressed and to determine the optimal printing parameters for high-performance composite part design.

Seta, Berin↗

Long fiber injection molding

An improved method for obtaining high fiber volume fraction, long fiber injection molded articles is provided. According to one embodiment, the method includes forming an injection molding feedstock by cutting pre-impregnated fiber-reinforced tape into platelets. The platelets can be coated with a thin layer of polymer to allow sliding of the platelets with respect to each other at the early stages of plastication, rather than forcing relative motion of fibers with respect to each other. The method can further include the dispersion of material only in the final stages of the injection molding screw to promote gentle motion of the feedstock at the earlier stages of the plastication process. The method allows improvement of mechanical properties of articles manufactured with equipment and techniques that are prevalent in high volume automotive and consumer industries.

Kunc, Vlastimil↗

Decontamination formulation with additive for enhanced mold remediation

Decontamination formulations with an additive for enhancing mold remediation. The formulations include a solubilizing agent (e.g., a cationic surfactant), a reactive compound (e.g., hydrogen peroxide), a carbonate or bicarbonate salt, a water-soluble bleaching activator (e.g., propylene glycol diacetate or glycerol diacetate), a mold remediation enhancer containing Fe or Mn, and water. The concentration of Fe.sup.2+ or Mn.sup.2+ ions in the aqueous mixture is in the range of about 0.0001% to about 0.001%. The enhanced formulations can be delivered, for example, as a foam, spray, liquid, fog, mist, or aerosol for neutralization of chemical compounds, and for killing certain biological compounds or agents and mold spores, on contaminated surfaces and materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Process Variability Effects on Tensile Response in Injection Molded, Fluorinated Thermoplastics

The mechanical properties of fluorinated thermoplastics (i.e., tensile strength and elongation) can vary with changes in injection molding processing parameters. Four fluoropolymers are examined: poly(vinylidene fluoride) (PVDF) and random poly(vinylidene fluoride-co-chlorotrifluoroethylene) (PVDF-CTFE) with three CTFE concentrations. Dog bones were manufactured with various cylinder dwell times and mold cooling times to assess the manufacturing sensitivity to the tensile response. Dwell and cooling times increasingly impact mechanical performance as CTFE concentration increases. Specimens exhibit higher tensile strength as a function of injection order. The first injected specimen exhibits the lowest tensile strength and highest elongation in all copolymers. This trend becomes more pronounced among fluoropolymers with higher CTFE concentration and lower weight-averaged molecular weight. Parallel plate rheology was used to obtain the zero-shear viscosity as a function of material type, process, and injection order. We found that in the copolymers, the first injected sample exhibited a lower zero-shear viscosity than the next, which indicates a lower molecular weight in the first injected specimen. This phenomenon was not presented for the PVDF homopolymer. Copolymer mechanical uncertainties are hypothesized to result from the shorter molecular weight chains extruding out of the specimens' sides as a flash due to higher mobility with CTFE segments.

36 MATERIALS SCIENCE↗