Search NASA⌕ Search

SEARCH · Search NASA

Results for “MOMENT DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Load distributions on slender delta wings having vortex flow

Results obtained through application of potential-flow theory based on a suction flow analogy for incompressible flow are compared to attached-flow theory and to experimental data acquired for sharp-edged delta wings. The error incurred in predicting structural loads on the basis of attached-flow theory is investigated. Force and moment coefficients and load distributions are used in the comparisons. The root bending moment can be estimated by assuming vortex lift concentrated at the wing leading edge. While this may entail some error at large angles of attack (owing to inboard movement of the center of vortex lift), it may furnish an upper bound in evaluating results based on other theories.

Kuhlman, J.↗
NASA NTRS1973

2-SPEED, a single-gimbal control moment gyro attitude control system.

In 2-SPEED (Two Scissored Pair Ensemble, Explicit Distribution) four single-gimbal control moment gyros (SGCMGs) configured into two scissored pairs are combined with an explicit distribution of angular momentum between pairs to produce a system relatively insensitive to the singularity problems which have plagued other SGCMG concepts. In this system, the singularity surfaces in momentum space degenerate to discrete curves. Further, the system permits a smooth passage through these remaining singularities with, at worst, a temporary delay while momentum redistribution takes place. Finally, CMG-out operation is possible within the full volume of the reduced momentum envelope.

Crenshaw, J. W.↗
NASA NTRS1959

The Effect of Moment of Area Rule Modifications on the Drag, Lift and Pitching Moment Characteristics of an Unswept Aspect Ratio 6 Wing and Body Combination

An experimental investigation was conducted to determine the effect of moment-of-area-rule modifications on the drag, lift, and pitching-moment characteristics of a wing-body combination with a relatively high aspect-ratio unswept wing. The basic configuration consisted of an aspect-ratio-6 wing with a sharp leading edge and a thickness ratio of 0.06 mounted on a cut-off Sears-Haack body. The model with full moment-of-area-rule modifications had four contoured pods mounted on the wing and indentations in the body to improve the longitudinal distributions of area and moments of area. Also investigated were modifications employing pods and indentations that were only half the size of the full modifications and modifications with partial body indentations. The models were tested at angles of attack from -2 deg to +12 deg at Mach numbers from 0.6 to 1.4. In general, the moment-of-area-rule modifications had a large effect on the drag characteristics of the models but only a small effect on their lift and pitching-moment characteristics. The modifications provided substantial reductions in the zero-lift drag at transonic and low supersonic speeds, but at subsonic speeds the drag was increased. Near Mach number 1.0, the model with full modification provided the greatest reduction in drag, but at the highest test Mach numbers the half modification gave the largest drag reduction. In general, the percent reductions of zero- lift drag obtained with the aspect-ratio-6 wing were as great or greater than those previously obtained with aspect-ratio-3 wings. The effect of the modifications on the drag due to lift was small except at Mach num- bers below 0.9 where the modified models had higher drag-rise factors. Above Mach number 0.9, the modified models had higher lift-drag ratios than the basic model. The modified models also had higher lift curve slopes and generally were slightly more stable than the basic configuration.

Dickey, Robert R.↗
NASA NTRS1988

Cosmological parameters and evolution of the galaxy luminosity function

The relationship between the observed distribution of discrete sources of a flux limited sample, the luminosity function of these sources, and the cosmological model is discussed. It is stressed that some assumptions about the form and evolution of the luminosity function must be made in order to determine the cosmological parameters from the observed distribution of sources. Presented is a method to test the validity of these assumptions using the observations. It is shown how, using higher moments of the observed distribution, one can determine, independently of the cosmological model, all parameters of the luminosity function except those describing evolution of the density and the luminosity of the luminosity function. These methods are applied to the sample of approximately 1000 galaxies recently used by Loh and Spillar to determine a value of the cosmological density parameter Omega approx = 1. It is shown that the assumptions made by Loh and Spillar about the luminosity function are inconsistent with the data, and that a self-consistent treatment of the data indicates a lower value of Omega approx = 0.2 and a flatter luminosity function. It should be noted, however, that incompleteness in the sample could cause a flattening of the luminosity function and lower the calculated value of Omega and that uncertainty in the values of these parameters due to random fluctuations is large.

Caditz, David↗
NASA NTRS1989

Cosmological parameters and evolution of the galaxy luminosity function

The relationship between the observed distribution of discrete sources of a flux limited sample, the luminosity function of these sources, and the cosmological model is discussed. It is stressed that some assumptions about the form and evolution of the luminosity function must be made in order to determine the cosmological parameters from the observed distribution of sources. Presented is a method to test the validity of these assumptions using the observations. It is shown how, using higher moments of the observed distribution, one can determine, independently of the cosmological model, all parameters of the luminosity function except those describing evolution of the density and the luminosity of the luminosity function. These methods are applied to the sample of approximately 1000 galaxies recently used by Loh and Spillar to determine a value of the cosmological density parameter Omega approx = 1. It is shown that the assumptions made by Loh and Spillar about the luminosity function are inconsistent with the data, and that a self-consistent treatment of the data indicates a lower value of Omega approx = 0.2 and a flatter luminosity function. It should be noted, however, that incompleteness in the sample could cause a flattening of the luminosity function and lower the calculated value of Omega and that uncertainty in the values of these parameters due to random fluctuations is large.

Caditz, David↗
NASA NTRS1987

Integrating nonlinear aerodynamic and structural analysis for a complete fighter configuration

The coupling of a nonlinear aerodynamics program with a structural analysis program to include the effects of static aeroelasticity in early preliminary design studies is described. A nonlinear, full potential aerodynamics method with capability to model geometric details of a complete aircraft in supersonic flow is used. The deflections of the lifting surfaces are calculated using an equivalent plate structural representation which can readily accommodate the changes in stiffness and geometric properties required during the preliminary design process. An iterative solution procedure is used to obtain consistent aerodynamic loads and structural deflections at the specified flight conditions. The volume of data transmitted between programs is minimized. The procedure is applied to a complete aircraft and the numerical results illustrate the aeroelastic effects on pressure distribution as well as total forces and moments. During this design study, the thickness distribution of the wing cover skins was initially sized based on rigid loads and subsequently resized under aeroelastic loads. Comparisons are made between these nonlinear aeroelastic results and results obtained from linear aerodynamic methods applied to a rigid shape during conceptual design studies.

Tatum, Kenneth E.↗
NASA NTRS1993

Kurtosis, skewness, and non-Gaussian cosmological density perturbations

Cosmological topological defects as well as some nonstandard inflation models can give rise to non-Gaussian density perturbations. Skewness and kurtosis are the third and fourth moments that measure the deviation of a distribution from a Gaussian. Measurement of these moments for the cosmological density field and for the microwave background temperature anisotropy can provide a test of the Gaussian nature of the primordial fluctuation spectrum. In the case of the density field, the importance of measuring the kurtosis is stressed since it will be preserved through the weakly nonlinear gravitational evolution epoch. Current constraints on skewness and kurtosis of primeval perturbations are obtained from the observed density contrast on small scales and from recent COBE observations of temperature anisotropies on large scales. It is also shown how, in principle, future microwave anisotropy experiments might be able to reveal the initial skewness and kurtosis. It is shown that present data argue that if the initial spectrum is adiabatic, then it is probably Gaussian, but non-Gaussian isocurvature fluctuations are still allowed, and these are what topological defects provide.

Luo, Xiaochun↗
NASA NTRS1980

Prediction of nacelle aerodynamic interference effects at low supersonic Mach numbers

The accuracy of analytical predictions of nacelle aerodynamic interference effects at low supersonic speeds are studied by means of test versus theory comparisons. Comparisons shown include: (1) isolated wing body lift, drag, and pitching moments; (2) isolated nacelle drag and pressure distributions; (3) nacelle interference shock wave patterns and pressure distributions on the wing lower surface; (4) nacelle interference effects on wing body lift, drag, and pitching moments; and (5) total installed nacelle interference effects on lift, drag, and pitching moment. The comparisons also illustrate effects of nacelle location, nacelle spillage, angle of attack, and Mach numbers on the aerodynamic interference. The initial results seem to indicate that the methods can satisfactorily predict lift, drag, pitching moment, and pressure distributions of installed engine nacelles at low supersonic Mach numbers with mass flow ratios from 0.7 to 1.0 for configurations typical of efficient supersonic cruise airplanes.

Kulfan, R. M.↗
NASA NTRS1987

Pressure distributions from high Reynolds number transonic tests of an NACA 0012 airfoil in the Langley 0.3-meter transonic cryogenic tunnel

Tests were conducted in the 2-D test section of the Langley 0.3-meter Transonic Cryogenic Tunnel on a NACA 0012 airfoil to obtain aerodynamic data as a part of the Advanced Technology Airfoil Test (ATAT) program. The test program covered a Mach number range of 0.30 to 0.82 and a Reynolds number range of 3.0 to 45.0 x 10 to the 6th power. The stagnation pressure was varied between 1.2 and 6.0 atmospheres and the stagnation temperature was varied between 300 K and 90 K to obtain these test conditions. Tabulated pressure distributions and integrated force and moment coefficients are presented as well as plots of the surface pressure distributions. The data are presented uncorrected for wall interference effects and without analysis.

Ladson, Charles L.↗
NASA NTRS1974

The subsequence weight distribution of summed maximum length digital sequences

An attempt is made to develop mathematical formulas to provide the basis for the design of pseudorandom signals intended for applications requiring accurate knowledge of the statistics of the signals. The analysis approach involves calculating the first five central moments of the weight distribution of subsequences of hybrid-sum sequences. The hybrid-sum sequence is formed from the modulo-two sum of k maximum length sequences and is an extension of the sum sequences formed from two maximum length sequences that Gilson (1966) evaluated. The weight distribution of the subsequences serves as an approximation to the filtering process. The basic reason for the analysis of hybrid-sum sequences is to establish a large group of sequences with good statistical properties. It is shown that this can be accomplished much more efficiently using the hybrid-sum approach rather than forming the group strictly from maximum length sequences.

Weathers, G. D.↗
NASA NTRS1975

A Method for Calculating the Induced Pressure Distribution Associated with a Jet in a Crossflow

A model is presented which can be used to study the loss of lift during hovering and horizontal flight of the VTOL aircraft. The model numerically predicts the pressure distribution induced by a round, turbulent, unheated, subsonic jet exhausting normally through a flat plate into a subsonic crossflow. The complete model assumes that the predominant features of the flow are jet entrainment and a pair of contrarotating vortices which form downstream of the jet. Experimentally determined vortex properties and a reasonable assumption concerning jet entrainment were used. Potential flow considerations were used except in the wake region, where a simple method for approximating the pressure distribution was suggested. The calculated pressure distribution, lift, and pitching moments on the flat plate are presented for a jet to crossflow velocity ratio of 8 and were compared with experimental results. A computer program is given which was used to calculate the pressure distribution across the flat plate.

Dietz, W. E., Jr.↗
NASA NTRS1994

Voids and constraints on nonlinear clustering of galaxies

Void statistics of the galaxy distribution in the Center for Astrophysics Redshift Survey provide strong constraints on galaxy clustering in the nonlinear regime, i.e., on scales R equal to or less than 10/h Mpc. Computation of high-order moments of the galaxy distribution requires a sample that (1) densely traces the large-scale structure and (2) covers sufficient volume to obtain good statistics. The CfA redshift survey densely samples structure on scales equal to or less than 10/h Mpc and has sufficient depth and angular coverage to approach a fair sample on these scales. In the nonlinear regime, the void probability function (VPF) for CfA samples exhibits apparent agreement with hierarchical scaling (such scaling implies that the N-point correlation functions for N greater than 2 depend only on pairwise products of the two-point function xi(r)) However, simulations of cosmological models show that this scaling in redshift space does not necessarily imply such scaling in real space, even in the nonlinear regime; peculiar velocities cause distortions which can yield erroneous agreement with hierarchical scaling. The underdensity probability measures the frequency of 'voids' with density rho less than 0.2 -/rho. This statistic reveals a paucity of very bright galaxies (L greater than L asterisk) in the 'voids.' Underdensities are equal to or greater than 2 sigma more frequent in bright galaxy samples than in samples that include fainter galaxies. Comparison of void statistics of CfA samples with simulations of a range of cosmological models favors models with Gaussian primordial fluctuations and Cold Dark Matter (CDM)-like initial power spectra. Biased models tend to produce voids that are too empty. We also compare these data with three specific models of the Cold Dark Matter cosmogony: an unbiased, open universe CDM model (omega = 0.4, h = 0.5) provides a good match to the VPF of the CfA samples. Biasing of the galaxy distribution in the 'standard' CDM model (omega = 1, b = 1.5; see below for definitions) and nonzero cosmological constant CDM model (omega = 0.4, h = 0.6 lambda(sub 0) = 0.6, b = 1.3) produce voids that are too empty. All three simulations match the observed VPF and underdensity probability for samples of very bright (M less than M asterisk = -19.2) galaxies, but produce voids that are too empty when compared with samples that include fainter galaxies.

Vogeley, Michael S.↗
NASA NTRS1993

Point charge representation of multicenter multipole moments in calculation of electrostatic properties

Distributed Point Charge Models (PCM) for CO, (H2O)2, and HS-SH molecules have been computed from analytical expressions using multi-center multipole moments. The point charges (set of charges including both atomic and non-atomic positions) exactly reproduce both molecular and segmental multipole moments, thus constituting an accurate representation of the local anisotropy of electrostatic properties. In contrast to other known point charge models, PCM can be used to calculate not only intermolecular, but also intramolecular interactions. Comparison of these results with more accurate calculations demonstrated that PCM can correctly represent both weak and strong (intramolecular) interactions, thus indicating the merit of extending PCM to obtain improved potentials for molecular mechanics and molecular dynamics computational methods.

Non-NASA Center↗
NASA NTRS1990

The X-ray flux dipole of active galactic nuclei and the peculiar motion of the Local Group

X-ray emission from 30 resolved AGN's are used to study the dipole moment of their flux distribution on the sky. The data are derived from the Piccinotti et al. (1982) survey. X-ray fluxes are analyzed in terms of the alignment with the direction of the Local Group (LG) of galaxies. It is observed that the direction of the dipole moment of the flux is (313 deg, 38 deg); the dipole direction deviates from the LG velocity by 39 deg. It is detected that the amplitude of the dipole is about 50 percent of the corresponding monopole. Based on a comparison of the data with previous observations it is suggested that the X-ray emission from AGNs traces the underlying mass distribution at least as strongly as optical and IR emission from galaxies.

Miyaji, Takamitsu↗
NASA NTRS1979

The effect of transverse shear in a cracked plate under skew-symmetric loading

The problem of an elastic plate containing a through crack and subjected to twisting moments or transverse shear loads is considered. By using a bending theory which allows the satisfaction of the boundary conditions on the crack surface regarding the normal and the twisting moments and the transverse shear load separately, it is found that the resulting asymptotic stress field around the crack tip becomes identical to that given by the elasticity solutions of the plane strain and antiplane shear problems. The problem is solved for uniformly distributed or concentrated twisting moment or transverse shear load and the normalized Mode II and Mode III stress-intensity factors are tabulated. The results also include the effect of the Poisson's ratio and material orthotropy for specially orthotropic materials on the stress-intensity factors.

Delale, F.↗
NASA NTRS1991

Quasi-periodic structures in the large-scale galaxy distribution and three-dimensional Voronoi tessellation

It has been suggested that the void and wall structure associated with the large-scale galaxy distribution might be qualitatively, or perhaps even physically, modeled by a Voronoi tessellation, and that such structure might account for the surprisingly regular, sharp peaks in the galaxy redshift distributions obtained from 'pencil beam' surveys. Taking cell wall crossings by random line segments to correspond to such redshift peaks, an exact expression is derived for the distribution of spacings of these intersections in a three-dimensional Voronoi tessellation. This result verifies that the spacings are nonrandom and quasi-periodic, qualitatively resembling the observed pattern, even though the cell wall structure is generated from randomly placed seeds. Finally, moments of the spacing distribution are used to show that apparently periodic samples, similar to those recently reported, represent only one to two sigma fluctuations in a Voronoi tesselation.

Ikeuchi, Satoru↗