Search NASA⌕ Search

SEARCH · Search NASA

Results for “Measured Response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

A Comparative Analysis of Occupant Response Between Component and Full Vehicle Tests of Fokker F28 Aircraft Hardware

In 2019, the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) conducted a full-scale crash test of a Fokker F28 MK1000 aircraft. This test concluded a multi-year research effort in which two component fuselage sections of a matching Fokker F28 aircraft were previously tested under similar vertical impact conditions. Due to facility and cost constraints of full-scale testing, aircraft are typically evaluated through component level tests (i.e. vertical drops of fuselage subsections or isolated seat tests). Although more practical, these tests are limited in their ability fully replicate the complex multi-axis loading environment induced on the occupants during a full-aircraft crash event. Because of this, there is risk that component level testing does not provide a complete assessment of vehicle crashworthiness. Comparative analysis between full-scale and component level testing of the Fokker F28 aircraft provides an excellent opportunity to evaluate differences in crashworthiness prediction made between these levels of test fidelity. In this study, Anthropomorphic Test Device (ATD, a.k.a crash test dummies) responses measured during the Fokker full scale impact test were compared to those measured in the component fuselage section drops. A variety of ATD configurations (5th, 50th, 95th) and positions (upright, braced) were tested in both the full-scale and component tests. ATD injury metric response comparisons were made across these ATD variations in addition to comparisons made with respect to ATD location within the vehicle. Results found the addition of horizontal impact velocity, achieved in the full-scale testing, along with aircraft structural effects altered ATD based crashworthiness assessment of the vehicle.

Crashworthiness↗
NASA NTRS1950

Dynamic Response of Control Servo System Installed in NAES-Equipped SB2C-5 Airplane (BuAer No. 83135)

Dynamic--response measurements for various conditions of displacement and rate signal input, sensitivity setting, and simulated hinge moment were made of the three control-surface servo systems of an NAES-equipped remote-controlled airplane while on the ground. The basic components of the servo systems are those of the General Electric Company type G-1 autopilot using electrical signal. sources, solenoid-operated valves, and hydraulic pistons. The test procedures and difficulties are discussed, Both frequency and transient-response data, are presented and comparisons are made. The constants describing the servo system, the undamped natural frequency, and the damping ratio, are determined by several methods. The response of the system with the addition of airframe rate signal is calculated. The transfer function of the elevator surface, linkage, and cable system is obtained. The agreement between various methods of measurement and calculation is considered very good. The data are complete enough and in such form that they may be used directly with the frequency-response data of an airplane to predict the stability of the autopilot-airplane combination.

Smaus, Louis H.↗
NASA NTRS1999

Advanced Techniques for Assessment of Postural and Locomotor Ataxia, Spatial Orientation, and Gaze Stability

In addition to adapting to microgravity, major neurovestibular problems of space flight include postflight difficulties with standing, walking, turning corners, and other activities that require stable upright posture and gaze stability. These difficulties inhibit astronauts' ability to stand or escape from their vehicle during emergencies. The long-ter7n goal of the NSBRI is the development of countermeasures to ameliorate the effects of long duration space flight. These countermeasures must be tested with valid and reliable tools. This project aims to develop quantitative, parametric approaches for assessing gaze stability and spatial orientation during normal gait and when gait is perturbed. Two of this year's most important findings concern head fixation distance and ideal trajectory analysis. During a normal cycle of walking the head moves up and down linearly. A simultaneous angular pitching motion of the head keeps it aligned toward an imaginary point in space at a distance of about one meter in front of a subject and along the line of march. This distance is called the head fixation distance. Head fixation distance provides the fundamental framework necessary for understanding the functional significance of the vestibular reflexes that couple head motion to eye motion. This framework facilitates the intelligent design of counter-measures for the effects of exposure to microgravity upon the vestibular ocular reflexes. Ideal trajectory analysis is a simple candidate countermeasure based upon quantifying body sway during repeated up and down stair stepping. It provides one number that estimates the body sway deviation from an ideal sinusoidal body sway trajectory normalized on the subject's height. This concept has been developed with NSBRI funding in less than one year. These findings are explained in more detail below. Compared to assessments of the vestibuo-ocular reflex, analysis of vestibular effects on locomotor function is relatively less well developed and quantified. We are improving this situation by applying methodologies such as nonlinear orbital stability to quantify responses and by using multivariate statistical approaches to link together the responses across separate tests. In this way we can exploit the information available and increase the ability to discriminate between normal and pathological responses. Measures of stability and orientation are compared to measures such as dynamic visual acuity and with balance function tests. The responses of normal human subjects and of patients having well documented pathophysiologies are being characterized. When these studies are completed, we should have a clearer idea about normal and abnormal patterns of eye, head, and body movements during locomotion and their stability in a wide range of environments. We plan eventually to use this information to validate the efficacy of candidate neurovestibular and neuromuscular rehabilitative techniques. Some representative studies made during this year are summarized.

Wall, Conrad., III↗
NASA NTRS1975

On the prediction of critical flutter conditions from subcritical response data and some related wind-tunnel experience

Methods of interpreting response measurements which could be amenable to flight flutter testing procedures were studied analytically and in the wind tunnel. One suggested scheme, which requires evaluation, is an iterative technique in which derivatives obtained from subcritical response data are used to indicate the approach to flutter. A simplification of this procedure was considered by examining the manner in which a single characteristic of the subcritical response behaves in relation to variations of the density or dynamic pressure in the approach to flutter. The use of this single parameter scheme was examined for random excitation as well as for sinusoidal forcing. The feasibility of the method is illustrated by several examples and the relative merits of random and sinusoidal excitation are discussed.

Houbolt, J. C.↗
NASA NTRS2021

Towards Disentangling Lockdown-Driven Air Quality Changes in the Northeastern U.S.

In the absence of preventive therapies or effective treatment for most cases of coronavirus disease 2019 (COVID-19), governments worldwide have sought to minimize person-to-person severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) transmission through a variety of lock-down measures and social distancing policies. Extreme events like the COVID-19 pandemic present a tremendous opportunity to make quantitative connections between changes in anthropogenic forcing, social and economic activity, and the related Earth system response. In this comment, we examine air quality impacts associated with pandemic response measures in the Northeastern United States.

Air Quality↗
NASA NTRS1995

Performance seeking control excitation mode

Flight testing of the performance seeking control (PSC) excitation mode was successfully completed at NASA Dryden on the F-15 highly integrated digital electronic control (HIDEC) aircraft. Although the excitation mode was not one of the original objectives of the PSC program, it was rapidly prototyped and implemented into the architecture of the PSC algorithm, allowing valuable and timely research data to be gathered. The primary flight test objective was to investigate the feasibility of a future measurement-based performance optimization algorithm. This future algorithm, called AdAPT, which stands for adaptive aircraft performance technology, generates and applies excitation inputs to selected control effectors. Fourier transformations are used to convert measured response and control effector data into frequency domain models which are mapped into state space models using multiterm frequency matching. Formal optimization principles are applied to produce an integrated, performance optimal effector suite. The key technical challenge of the measurement-based approach is the identification of the gradient of the performance index to the selected control effector. This concern was addressed by the excitation mode flight test. The AdAPT feasibility study utilized the PSC excitation mode to apply separate sinusoidal excitation trims to the controls - one aircraft, inlet first ramp (cowl), and one engine, throat area. Aircraft control and response data were recorded using on-board instrumentation and analyzed post-flight. Sensor noise characteristics, axial acceleration performance gradients, and repeatability were determined. Results were compared to pilot comments to assess the ride quality. Flight test results indicate that performance gradients were identified at all flight conditions, sensor noise levels were acceptable at the frequencies of interest, and excitations were generally not sensed by the pilot.

Schkolnik, Gerard↗
NASA NTRS1993

Thermal history effects on electrical relaxation and conductivity for potassium silicate glass with low alkali concentrations

Electrical response measurements from 10 Hz to 100 kHz between 120 and 540 C were made on potassium-silicate glasses with alkali oxide contents of 2, 3, 5 and 10 mol percent. Low alkali content glasses were chosen in order to try to reduce the Coulombic interactions between alkali ions to the point that frozen structural effects from the glass could be observed. Conductivity and electrical relaxation responses for both annealed and quenched glasses of the same composition were compared. Lower DC conductivity (sigma(sub DC)) activation energies were measured for the quenched compared to the annealed glasses. The two glasses with the lowest alkali contents exhibited a non-Arrhenius concave up curvature in the log(sigma(sub DC)) against 1/T plots, which decreased upon quenching. A sharp decrease in sigma(sub DC) was observed for glasses containing K2O concentrations of 5 mol percent or less. The log modulus loss peak (M'') maximum frequency plots against 1/T all showed Arrhenius behavior for both annealed and quenched samples. The activation energies for these plots closely agreed with the sigma(sub DC) activation energies. A sharp increase in activation energy was observed for both series as the potassium oxide concentration decreased. Changes in the electrical response are attributed to structural effects due to different alkali concentrations. Differences between the annealed and quenched response are linked to a change in the distribution of activation energies (DAE).

Angel, Paul W.↗
NASA NTRS1982

Some statistical performance characteristics of the 'ITD' modal identification algorithm

Performance characteristics of the Ibrahim time-domain algorithms are examined on a statistical basis. The method uses multiple free-response measurements from a test structure directly in the time domain, and displays varying accuracy, with the strongly excited modes identified most accurately and the weakly excited modes least accurately. Sets of computer-generated free-response functions for a simple 1-mode model are used to study the identification performance for several basic changes in the modal characteristics of the data, the user-selectable analysis constants, and the level of superimposed noise. Results indicate the existence of a direct and often linear effect of noise on the scatter of identified parameters, and good identification is maintained at the 1% noise level down to the point in frequency when only 1/4-cycle of data is analyzed.

Pappa, R. S.↗
NASA NTRS1984

Use of impedance plethysmography to continually monitor bone marrow blood flow

An impedance-plethysmographic technique is described which can be used to quantify temporal bone-marrow blood-flow changes. Results obtained with the impedance technique compare favorably with the data from simultaneously administered microspheres. Injection of sympathomimetic drugs produced measurable responses: isoproterenol caused a significant increase in bone-marrow blood flow within 1 min, and levarterenol decreased bone-marrow blood flow. Data obtained with impedance plethysmography suggest that the technique is feasible for multiple measurements on the same animal and that the technique can be used to study acute or chronic changes in bone-marrow blood flow following various experimental treatments.

Montgomery, L. D.↗
NASA NTRS1987

Test procedures for detection of in-flight propeller-induced structure-borne noise

A potentially important source of structure-borne interior noise transmission in advanced turboprop aircraft is the impingement of the propeller wake/vortex on downstream aerodynamic surfaces. It can only be safely assumed that this potential source of interior noise may well hold up achievable interior noise levels unless noise control measures are conscientiously incorporated into the aircraft design. Through the use of a laboratory based test apparatus, techniques were developed to estimate the level of in-flight structure-borne noise transmission from combined frequency response function ground testing and in-flight structural response measurements. All phases of the test procedure were simulated in the laboratory and the expected level of accuracy of the procedure is addressed.

Unruh, J. F.↗
NASA NTRS1975

Update on an investigation of flight buffeting of a variable-sweep aircraft

A detailed investigation of flight buffeting response of an F-111A aircraft was performed. AIAA Paper No. 74-358 presented results of an initial study of wing and fuselage responses measured at subsonic speeds and wing leading-edge sweep of 26 degrees. The present paper gives additional results for wing sweeps of 26, 50 and 72.5 degrees at Mach numbers up to 1.2 including horizontal tail responses. Power spectra, response time histories, variations of rms response with angle of attack, and effects of Mach number and wing sweep angle are discussed.

Benepe, D. B.↗
NASA NTRS1986

SSME main injector 4000 Hertz phenomenon

Several Space Shuttle Main Engines (SSME) have experienced very high acceleration responses measured in the main injector of the powerhead during static firings. Data from previous hot fire SSME tests relating to the 4000 hertz phenomenon were reviewed to provide a better understanding of the nature of this structural response. The objective was to technically understand the way this phenomenon works, recommend a fix and test the fix.

Johnston, G. D.↗
NASA NTRS1987

Detection of in-flight propeller-induced structure-borne noise

A potentially important source of structure-borne interior noise transmission in advanced turboprop aircraft is the impingement of the propeller wake/vortex on downstream aerodynamic surfaces. It can be safely assumed that this potential source of interior noise may well adversely affect achievable interior noise levels unless noise control measures are conscientiously incorporated into the aircraft design. Through the use of a laboratory-based test apparatus, techniques were developed to estimate the level of in-flight structure-borne noise transmission from combined frequency response function ground testing and in-flight structural response measurements. All phases of the procedure were simulated in the laboratory and the expected level of accuracy of the procedure is addressed.

Unruh, J. F.↗
NASA NTRS1980

Workshop report: Velocity coupling

Velocity coupled combustion instability and related combustion instability topics were considered. The knowledge of velocity coupled combustion instability was assessed; the state of the art of velocity coupled measurement techniques was determined; and particularly laboratory devices or T burner related devices; recommendations were made on how to improve the state of knowledge on velocity coupled combustion instability. Test conditions for a round robin of velocity coupled response measurement techniques were established.

Beckstead, M. W.↗
NASA NTRS1991

Basic research on design analysis methods for rotorcraft vibrations

The objective of the present work was to develop a method for identifying physically plausible finite element system models of airframe structures from test data. The assumed models were based on linear elastic behavior with general (nonproportional) damping. Physical plausibility of the identified system matrices was insured by restricting the identification process to designated physical parameters only and not simply to the elements of the system matrices themselves. For example, in a large finite element model the identified parameters might be restricted to the moduli for each of the different materials used in the structure. In the case of damping, a restricted set of damping values might be assigned to finite elements based on the material type and on the fabrication processes used. In this case, different damping values might be associated with riveted, bolted and bonded elements. The method itself is developed first, and several approaches are outlined for computing the identified parameter values. The method is applied first to a simple structure for which the 'measured' response is actually synthesized from an assumed model. Both stiffness and damping parameter values are accurately identified. The true test, however, is the application to a full-scale airframe structure. In this case, a NASTRAN model and actual measured modal parameters formed the basis for the identification of a restricted set of physically plausible stiffness and damping parameters.

Hanagud, S.↗
NASA NTRS1994

Immune Response and Function: Exercise Conditioning Versus Bed-Rest and Spaceflight Deconditioning

Immune responses measured at rest immediately or some hours after exercise training (some with and some without increase in maximal oxygen uptake) gave variable and sometimes conflicting results; therefore, no general conclusions can be drawn. On the other hand, most immune responses were either unchanged (immunoglobulin, T cells, CD4+, and natural killer activity) or decreased (blood properdin, neutrophil phagocytic activity, salivary lysozymes, brain immunoglobulin A and G, and liver B lymphocytes and phytohemagglutinin activity) during prolonged bed rest. Some data suggested that exercise training during bed rest may partially ameliorate the decreased functioning of the immune system. Exercise and change in body position, especially during prolonged bed rest with plasma fluid shifts and diuresis, may induce a change in plasma protein concentration and content, which can influence drug metabolism as well as immune function. Leukocytosis, accompanied by lymphopenia and a depressed lymphocyte response, occurs in astronauts on return to Earth from spaceflight; recovery may depend on time of exposure to microgravity. It is clear that the effect of drugs and exercise used as countermeasures for microgravity deconditioning should be evaluated for their effect on an astronaut's immune system to assure optimal health and performance on long-duration space missions.

Greenleaf, J. E.↗
NASA NTRS2003

Developing a MATLAB(registered)-Based Tool for Visualization and Transformation

An important step in the structural design and development of spacecraft is the experimental identification of a structure s modal characteristics, such as its natural frequencies and modes of vibration. These characteristics are vital to developing a representative model of any given structure or analyzing the range of input frequencies that can be handled by a particular structure. When setting up such a representative model of a structure, careful measurements using precision equipment (such as accelerometers and instrumented hammers) must be made on many individual points of the structure in question. The coordinate location of each data point is used to construct a wireframe geometric model of the structure. Response measurements obtained from the accelerometers is used to generate the modal shapes of the particular structure. Graphically, this is displayed as a combination of the ways a structure will ideally respond to a specified force input. Two types of models of the tested structure are often used in modal analysis: an analytic model showing expected behavior of the structure, and an experimental model showing measured results due to observed phenomena. To evaluate the results from the experimental model, a comparison of analytic and experimental results must be made between the two models. However, comparisons between these two models become difficult when the two coordinate orientations differ in a manner such that results are displayed in an unclear fashion. Such a problem proposes the need for a tool that not only communicates a graphical image of a structure s wireframe geometry based on various measurement locations (called nodes), but also allows for a type of transformation of the image s coordinate geometry so that a model s coordinate orientation is made to match the orientation of another model. Such a tool should also be designed so that it is able to construct coordinate geometry based on many different listings of node locations and is able to transform the wireframe coordinate orientation to match almost any possible orientation (i.e. it should not be a problem specific application) if it is to be of much value in modal analysis. Also, since universal files are used to store modal parameters and wireframe geometry, the tool must be able to read and extract information from universal files and use these files to exchange model data.The purpose of this project is to develop such a tool as a computer graphical user interface (GUI) capable of performing the following tasks: 1) Browsing for a particular universal file within the computer directory and displaying the name of this file to the screen; 2) Plotting each of the nodes within the universal file in a useful, descriptive, and easily understood figure; 3) Reading the node numbers from the selected file and listing these node numbers to the user for selection in an easily accessible format; 4) Allowing for user selection of a new model orientation defined by three selected nodes; and 5) Allowing the user to specify a directory to which the transformed model s node locations will be saved, and saving the transformed node locations to the specified file.

Anderton, Blake J.↗
NASA NTRS1990

Possibilities for LWIR detectors using MBE-grown Si(/Si(1-x)Ge(x) structures

Traditionally, long wavelength infrared (LWIR) detection in Si-based structures has involved either extrinsic Si or Si/metal Schottky barrier devices. Molecular beam epitaxially (MBE) grown Si and Si/Si(1-x)Ge(x) heterostructures offer new possibilities for LWIR detection, including sensors based on intersubband transitions as well as improved conventional devices. The improvement in doping profile control of MBE in comparison with conventional chemical vapor deposited (CVD) Si films has resulted in the successful growth of extrinsic Si:Ga, blocked impurity-band conduction detectors. These structures exhibit a highly abrupt step change in dopant profile between detecting and blocking layers which is extremely difficult or impossible to achieve through conventional epitaxial growth techniques. Through alloying Si with Ge, Schottky barrier infrared detectors are possible, with barrier height values between those involving pure Si or Ge semiconducting materials alone. For both n-type and p-type structures, strain effects can split the band edges, thereby splitting the Schottky threshold and altering the spectral response. Measurements of photoresponse of n-type Au/Si(1-x)Ge(x) Schottky barriers demonstrate this effect. For intersubband multiquntum well (MQW) LWIR detection, Si(1-x)Ge(x)/Si detectors grown on Si substrates promise comparable absorption coefficients to that of the Ga(Al)As system while in addition offering the fundamental advantage of response to normally incident light as well as the practical advantage of Si-compatibility. Researchers grew Si(1-x)Ge(x)/Si MQW structures aimed at sensitivity to IR in the 8 to 12 micron region and longer, guided by recent theoretical work. Preliminary measurements of n- and p-type Si(1-x)Ge(x)/Si MQW structures are given.

Hauenstein, Robert J.↗