Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

The Effect of Composition on Microstructure and Properties for Additively Manufactured Superalloy 718

Additive manufacturing (AM) represents an exciting new approach towards producing metallic aerospace components. The ability to make complex geometries that were impossible to create using conventional manufacturing methods has sparked interest from the aerospace community, including NASA. The use of AM components for crucial and human rated space missions necessitates a full characterization of the differences between AM and more conventional wrought and cast processes. For this study, sixteen different commercially available superalloy 718 powder feedstocks were obtained, built using laser powder bed fusion(L-PBF), and microstructurally and mechanically analyzed. These measurements revealed a wide range of build qualities and microstructures despite all powder lots falling within the 718chemical specification and being processed using the same prescribed build and heat treatment parameters. Statistical analysis found a strong correlation of the amount of carbon in the powder with the final grain size and strength of the heat-treated 718 part. Ultimately, this study highlights the need of a refined superalloy 718 chemical specification for powder lots to be used in AM.

Timothy M Smith↗
DOE OSTI2019

Significance of Finish Cooling Temperature to Microstructure and Property Relationship of Low-Carbon V-N-Cr Microalloyed High-Strength Steel

Herein, three final cooling temperatures were employed to achieve high strength and toughness communication in the V-N-Cr microalloyed steels. This study shows that V-N-Cr microalloyed steel primarily consisted of ferrite, granular bainite, acicular ferrite, and a small quantity of M/A phase at the final cooling temperature of 600 °C, while the polygonal ferrite, lamellar bainite, granular bainite, and a small fraction of acicular ferrite were obtained at 450 °C. The width of lamellar bainite was ~ 200-400 nm, and acicular ferrite was composed of fine non-parallel ferrite platelet structures with high dislocations densities. As the final cooling temperature decreased further, the microstructure included granular bainite and lath bainite at 350 °C. The nanoscale precipitates of V-N-Cr microalloyed steel were divided into two types, large-scale precipitates near the grain boundary that precipitated at high temperatures and small precipitates of diameter 5-10 nm at low temperatures, which significantly contributed toward strength. The hot rolled low-carbon V-N-Cr microalloy steel exhibited optimal mechanical properties at the final rolling temperature of 830 °C, as well the final cooling temperature was 450 °C. The highest yield strength and tensile strength of V-N-Cr microalloyed steel were 835 MPa and 989 MPa, respectively. The outstanding impact toughness of 161 J tested at − 60 °C was received. The transformation strengthening and precipitation hardening played a crucial role in affecting the thermo-mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of Radiation Induced Defects Across Scales

The Whole Powder Pattern Modelling (WPPM) approach of diffraction line profile analysis (LPA) was applied for the first time on PuO 2 in order to understand the evolution of the microstructural properties as a function of process conditions. Crystallite size distributions and defect concentrations were determined by WPPM on three different PuO 2 samples - including one with a bimodal distribution and compared to the result of more common LPA analyses used in PuO 2 literature studies (e.g. Scherrer equation, double Voigt method). The conclusion was that a lognormal distribution of spherical crystallites with dislocations most closely represent the microstructure of PuO 2 produced by heating Pu 2 (C 2 O 4 ) 3 (H 2 O) 6 •3H 2 O between 650°C and 850°C. The volume-weighted mean column length (Lvol) parameter obtained from the double Voigt method for the monomodal samples were the same as the Lvol obtained from the WPPM within uncertainty. The two LPA methods did not agree on the Lvol parameters of the bimodal distribution sample with only the WPPM getting values that were consistent with the individual components. The WPPM can potentially provide more insight into future studies of the influences on the microstructure properties of PuO 2 .

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Microstructure and Properties of Ni-WC Composite Coatings on Their Solid Particle Erosion Behavior

Metal matrix composites (MMCs) of WC in Co or Ni matrices are widely used due to their high wear resistance. Previous studies showed that tailoring the mechanical properties through optimum WC content can significantly extend the life cycle of MMCs. In this study, composite coatings of Ni with various WC content ranging from 10 to 55 vol.% were cold sprayed using agglomerated WCNi powders and two different sizes of Ni powders, − 10 + 4 (d{sub 50} = 7 µm) referred to as Ni(7) and − 35 + 15 (d{sub 50} = 25 µm) to as Ni(25). Microstructural characterization, including the deformed structure of Ni splats and retention and distribution of WC, was performed by scanning electron microscopy (SEM). Composite coatings were subjected to solid particle erosion following ASTM G76-13 standard. At low WC content coatings, erosion occurred primarily by plastic deformation of Ni matrices and knocking out of WC particles. At high WC concentrations, network distribution of compacted WCNi particles in the matrices led to a significant drop in erosion rates of coatings, due to a change in erosion mechanism from severe cutting and plowing of Ni and WC dislodging to WCNi splats spalling. Composite coatings sprayed using finer size Ni powder were usually more erosion resistant.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Properties and microstructure evolution of silicon nitride and zirconium nitride following Ni ion irradiation

We report that silicon nitride and zirconium nitride have been proposed as potential materials for multiple nuclear applications (inert matrix fuels, accident tolerant fuels, space nuclear power, fusion reactor design), yet knowledge on their behavior under irradiation remains limited. Ion irradiations were performed using 15 MeV Ni 5+ ions on Si 3 N 4 and ZrN samples, with midrange doses (around 3 µm) from 1 to 50 dpa and temperatures from 300 to 700°C. Volumetric lattice swelling was determined by grazing incidence X-ray diffraction, defect production and evolution were tracked using Transmission Electron Microscopy, and nanoindentation was performed to quantify the ceramics’ mechanical properties evolution. The results from these irradiation studies on nitride ceramics help fill the current gap present in the literature. Behavior consistent with past work on irradiated Si 3 N 4 was observed with respect to mechanical properties and defect formation up to 15 dpa and 500°C. Failure of the grain boundary sintering aid in Si 3 N 4 was observed above these conditions. Different behavior was observed in both nitrides at 50 dpa and 700°C, where lattice swelling increased past potential saturation values. Unreported cavity formation was witnessed in both materials under all irradiation conditions, with stable number density and slight size increase above 15 dpa. The mechanism for the cavity formation remains to be determined.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Time-dependent THMC properties and microstructural evolution of damaged rocks in excavation damage zone

Modeling coupled thermo-hydro-mechanical-chemical (THMC) processes in host rocks near high-level nuclear waste (HLW) repositories at various time scales is an extremely challenging task. The current study integrates experimental, theoretical, and numerical methods in assessing the evolution of excavation damage zone (EDZ) over time and its implication on the long-term migration of hazardous species. Argillite and rock salt and are the focus of this study. The first part of the report presents a novel time-dependent directional microcrack damage theory for generic brittle rocks. It features detailed statistical description of the microcracks within a damaged solid, permitting a direct upscaling of microscale processes such as crack growth kinetics, crack closure/opening, sliding friction to explain the macroscopic creep, nonlinear elasticity, shear dilation, and loading-unloading hysteresis. This provides a basic platform for describing the anisotropic mechanical and transport properties of damaged rocks during excavation and subsequent THMC loadings. The model is validated and numerically implemented to Finite Element (FE) package ABAQUS through the user-defined material (UMAT) interface and have demonstrated great potential in resolving the time-dependent and anisotropic evolution of damage in the EDZ. The second part of the report presents a multi-scale experimental effort in characterizing the thermal, hydraulic, and mechanical properties of Mancos shale and Avery Island salt. For the Mancos shale, triaxial compression tests are performed at different confining pressures and temperatures to probe its thermomechanical properties relevant to HLW repositories. The obtained stress-strain data are interpreted using the proposed directional damage theory. Post-test specimens are subjected to gas permeability tests to reveal the correlation between permeability and the degree of microcracking. At microscale, temperature-controlled nanoindentation tests are performed and found a linear correlation between fracture toughness and elastic modulus from 25°C to 300°C. For Avery Island salt, we have designed and manufactured a novel relative-humidity controlled uniaxial creep device. Long-term creep tests at low stresses (< 5 MPa) are performed at different levels of relative humidity (RH). Besides confirming the much higher creep rates as one would expect through extrapolating the high-stress creep data, the results reveal that the steady-state creep rate of rock salt is strongly dependent on the ambient RH, an aspect that is often neglected in the literature. Both behaviors can be attributed to the pressure-solution creep mechanism which dominates at low stress and high RH levels. The third part of the report explores a set of numerical strategies in modeling the THMC behavior of porous geomaterials. A fully implicit, monolithic FE solution that can flexibly interface with different material models and coupling mechanisms for THMC problems is developed and verified through the ABAQUS user-defined element (UEL) interface. The scheme is used to study the THM response of a hypothetical HLW storage site with reference to an existing in-situ heater test. Strategies for integrating the UEL and the microcrack UMAT are suggested. Another numerical endeavor of this study is to implement a higher-order asymptotic homogenization method to account for the heterogeneous porous structures. The same method is then extended to perform microstructure-informed thermo-mechanical modeling of generalized continua. The above outcomes of this project provide a strong thrust towards enhancing the fundamental understanding and modeling capability of the long-term evolution of host rocks in EDZ, thus helping achieve the design goal of 1-million-year isolation of high-level nuclear wastes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Microstructural and Property Evolution of Continuous Columnar-Grained Polycrystalline Copper during Extreme Plastic Deformation at Room Temperature

An extreme extensibility with a true strain of 11.12 has been obtained for continuous columnar-grained (CCG) polycrystalline copper at room temperature, which was cold-drawn from a 10-mm-diameter as-cast rod into a 38.5-μm-diameter ultra-fine wire without any intermediate softening heat treatment. During the extreme plastic deformation, the ultimate tensile stress increased from 140 MPa for as-cast CCG copper to 525 MPa for the deformed sample at a true stain of 11.12, while the relative electrical conductivity maintained a high value of 97.6% IACS. On this basis, CCG copper is an excellent raw material for the fabrication of ultra-fine wires with both high strength and high electrical conductivity. The original columnar grains experienced grain subdivision and formed fibrous grains along the drawing direction with a fibrous longitudinal morphology and curly transverse microstructure at medium to high strain. The subdivision of the fibrous grains then went on as the extreme plastic deformation continued. Large amounts of strain-induced boundaries and microstructural refinement facilitated the storage of abundant glide dislocations created by extreme plastic deformation. Thus, extreme plastic extensibility can be achieved through continuous work hardening of CCG copper.

36 MATERIALS SCIENCE↗
DOE OSTI2024

3D Printing of Inconel 718 with Enhanced Boron Composition as a Novel Solar Absorber Tube Material in the Concentrated Solar Power (CSP) System

The growing demands for elevated efficiency in the solar energy industry led researchers to focus on the development of functional solar absorber tube material in concentrated solar power (CSP) systems, when molten salts are adopted as the heat transfer fluid. In this study, the typical solar absorber tube material, Inconel 718, was enhanced with boron to achieve a higher solar absorptivity in the visible light spectrum. Combined with an additive manufacturing (AM) method, the boron composition exceeded the traditional manufacturing limit of 60 ppm without microstructural defects. The boron-enhanced Inconel 718 exhibited a high solar absorptivity of nearly 90 % while maintaining a high thermal cycle fatigue resistance after thermal cycling treatment between 550°C and 720°C. The boron composition was increased to the manufacturing failure point, and the effects of different boron compositions on mechanical properties, microstructure, and optical properties were studied. The provided microstructure-property map in this study delivers high potentials of functional AM-printed alloy material in CSP applications.

13 HYDRO ENERGY↗
DOE OSTI2018

Effect of Tool Temperature on Microstructure and Properties of Tailored Hot Stamping Components

Traditional boron steel hot stamping technology can achieve components with full martensite and tensile strength of 1500 MPa. However, fully martensitic hot stamped components exhibit very low level of ductility and are rarely used in energy absorbing structures. Hot stamping with segmented heating and cooling tool can obtain multiphase quenched structures and the tailored mechanical properties. Hot stamping experiment of U-shape component was performed with segmented heating and cooling tool. Mechanical properties of the formed component were measured, and scanning electron microscope and color tint etching were used to quantify the quenched phases achieved under different tool temperatures. The results showed that hardness value decreased from 470 to 230 HV and tensile strength reduced about 50% from 1406 to 730 MPa and elongation increased from 4.19 to 10.20% as tool temperatures increased from 25 to 500 °C. Meanwhile, martensite decreased from 85 to 30% and bainite increased from 12 to 55%, and there was also a small increase in ferrite. In order to get the influence of quenched phases on the strength and hardness of tailored hot stamped component, linear fitting optimization was used to establish mathematical models for area fraction of quenched phases and strength and hardness.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of tailored martensitic transformation in a thick weld: Residual stresses mitigation, heterogeneous microstructure, and mechanical properties

The residual stresses, microstructural heterogeneities, and mechanical properties were extensively examined in a 25 mm thick weld consisting of two regions which respectively undergo phase transformation at relatively low (100 °C) temperature (LTT) and high (670 °C) temperature (HTT) during cooling. Due to the LTT martensitic transformation, which features a transformation strain of ~4000 με, large compressive residual stress (−510 MPa) was generated as confirmed by neutron diffraction and contour method. Meanwhile, significant heterogeneities were observed in terms of the chemical composition, yield strength, and microhardness across the interface between the LTT and HTT regions. The dependency of martensitic transformation starting temperature (M{sub s}) on chemical composition is empirically formulated, and it reveals that the dependency of M{sub s} on the Ni and Cr compositions becomes stronger when the temperature is lower than 200 °C. The maximum change of residual stresses (σ{sub x}{sup max}) exponentially decreases as M{sub s} decreases in the manner of σ{sub x}{sup max} = 97.5 exp(M{sub s}/227)-649. The fracture behavior was found highly dependent upon the volume fraction of retained austenite influenced by M{sub s}. While a ductile fracture mode was found in the cellular LTT region containing relatively higher amount of retained austenite (~10%), the interface shows transgranular brittle fracture features and sub-cracking due to the relatively small amount of retained austenite and the predominant martensite constituent.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Investigation on Target Erosion and Effect of Deposition Rate on Microstructure and Properties of Sputtered Be Coating

The beryllium coatings were prepared by direct current magnetron sputtering at different powers. The target erosion rate was theoretically predicted on the basis of the conservation of electric charge and mass. The experiment based on weighing method was performed, which verified the theoretical prediction. XRD analysis reveals that the sputter coatings mainly consist of α-Be phase. On increasing deposition rates, the surface morphology shows a transition from a regular equiaxed grain to a cauliflower-like polygrain owing to the irregular arrangement of atoms and bulk diffusion enhancement originating from the sputtering thermal effect. A heterogeneous particulate-induced growth was observed and derived from fallen scrap during the sputtering process. The surface roughness displays a power function with the thickness increment, while the electrical resistivity is reversed with the grain size.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Tailoring Microstructure and Properties of a Superelastic Ti–Ta Alloy by Incorporating Spark Plasma Sintering with Thermomechanical Processing

A powder metallurgy Ti–35 at.% Ta alloy was produced using a spark plasma sintering process. The sintered alloy exhibited Ta-rich regions at a sintering temperature of 1100 °C. Complete diffusion of elemental powders was achieved via homogenization heat treatment at 1500 °C for 12 h, but the ductility declined drastically. The brittle behavior of the homogenized sample was due to the high-oxygen content, continuous grain boundary α-phase and high-angle grain boundaries. Excellent mechanical properties were achieved when hot forging was used along with preheating the homogenized specimen at 1100 °C. The mechanisms underlying this phenomenon were suppression of the solid grain boundary α-phase, high fraction of low-angle grain boundaries and dynamic recrystallization. Tensile strength improved to the maximum value of 868 MPa. The strain recovery ratio increased to 90% in the first cycle during a cyclic loading–unloading test. Incomplete strain recovery of the first cycle was due to the presence of the martensite phase (α″).

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of ECAP Die Angles on Microstructure Mechanical Properties and Corrosion Behavior of AZ80 Mg Alloy

In this article, the effect of channel angles on material properties was investigated during equal channel angular pressing of AZ80 magnesium alloy using processing route R at 325 °C processing temperature. Channel angles of 90° and 110° and common corner angle 30° have been considered for this study. It has been revealed that the channel angle has a significant influence on deformation homogeneity, microhardness, ultimate tensile strength, ductility and corrosion behavior of Mg alloys. Investigation with reference to as-received AZ80 Mg alloy indicates 18.47% improvement in UTS and 76.07% enhancement in ductility after processing through 3P-90° and 2P-110° ECAP, respectively. Also, the corrosion rate reduces to 89.47% after processing the sample with 3P-110° ECAP die.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical properties and microstructure of 316L stainless steel produced by hybrid manufacturing

Hybrid manufacturing is a combination of additive (deposition) and subtractive (machining) manufacturing in a single machine tool. Such a system can be used for near net shape manufacturing and component repair using either similar or dissimilar materials. Integrated into a single system, transition between additive and subtractive manufacturing can occur immediately and be leveraged to generate large components by alternating between the processes. In this investigation, we show how the interleaved capabilities can reduce overall cycle time by up to 68 %, improve average relative elongation to failure by 71 %, and reduce the average relative porosity fraction by 83 % when compared to traditional additive manufactured components. Results from this investigation builds the foundation needed for hybrid manufacturing to be applicable towards the manufacture of large complex components such as nosecones and marine propulsors.

36 MATERIALS SCIENCE↗