Search NASA⌕ Search

SEARCH · Search NASA

Results for “Monte Carlo simulations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of substrate tilt on sputter-deposited AuTa films

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. However, growth mechanisms of such Au-Ta alloy films are not well understood. Here, we systematically study the effect of substrate tilt on properties of films deposited by direct current magnetron sputtering from a AuTa alloy target. Experimental data is correlated with distributions of landing energies and incident angles of sputtered and backscattered species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Results reveal that the deposition rate and film density monotonically decrease with increasing substrate tilt. Properties are similar for films with a tilt of 40° and below: films are amorphous, with an average compressive stress of 0.5 GPa, a density of 16 g/cm 3 , and electrical resistivity of 200 μΩ cm. The critical substrate tilt angle for the onset of porosity, a transition to a reduced stress state, and an increase in electrical resistivity lies between 40 and 60°. Based on Monte Carlo simulations, these changes in film properties are correlated with an increase in the average impact angle of the ballistic component of atomic flux. Implications of these results to deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Toward alcohol synthesis from CO hydrogenation on Cu(111)-supported MoS 2 – predictions from DFT+KMC

In the quest for cheap and efficient catalysts for alcohol synthesis from syngas, a material of interest is single-layer MoS2 owing to its low cost, abundancy, and flexible structure. Because of the inertness of its basal plane, however, it is essential to find ways that make it catalytically active. Herein, by means of density functional theory based calculations of reaction pathways and activation energy barriers and accompanying kinetic Monte Carlo simulations, we show that while S vacancy row structures activate the MoS 2 basal plane, further enhancement of chemical activity and selectivity can be achieved by interfacing the MoS 2 layer with a metallic support. When defect-laden MoS2 is grown on Cu(111), there is not only an increase in the active region (surface area of active sites) but also charge transfer from Cu to MoS 2 , resulting in a shift of the Fermi level such that the frontier states (d orbitals of the exposed Mo atoms) appear close to it, making the MoS 2 /Cu(111) system ready for catalytic activity. Finally, our calculated thermodynamics of reaction pathways lead to the conclusion that the Cu(111) substrate promotes both methanol and ethanol as the products, while kinetic Monte Carlo simulations suggest a high selectivity toward the formation of ethanol.

2D materials↗
DOE OSTI2021

Monte Carlo Modeling and Design of Photon Energy Attenuation Layers for >10× Quantum Yield Enhancement in Si-Based Hard X-ray Detectors

High-energy (>20 keV) X-ray photon detection at high quantum yield, high spatial resolution, and short response time has long been an important area of study in physics. Scintillation is a prevalent method but limited in various ways. Directly detecting high-energy X-ray photons has been a challenge to this day, mainly due to low photon-to-photoelectron conversion efficiencies. Commercially available state-of-the-art Si direct detection products such as the Si charge-coupled device (CCD) are inefficient for >10 keV photons. Here, we present Monte Carlo simulation results and analyses to introduce a highly effective yet simple high-energy X-ray detection concept with significantly enhanced photon-to-electron conversion efficiencies composed of two layers: a top high-Z photon energy attenuation layer (PAL) and a bottom Si detector. We use the principle of photon energy down conversion, where high-energy X-ray photon energies are attenuated down to ≤10 keV via inelastic scattering suitable for efficient photoelectric absorption by Si. Our Monte Carlo simulation results demonstrate that a 10–30× increase in quantum yield can be achieved using PbTe PAL on Si, potentially advancing high-resolution, high-efficiency X-ray detection using PAL-enhanced Si CMOS image sensors.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Confinement/deconfinement transition in the D0-brane matrix model — A signature of M-theory?

We study the confinement/deconfinement transition in the D0-brane matrix model (often called the BFSS matrix model) and its one-parameter deformation (the BMN matrix model) numerically by lattice Monte Carlo simulations. Our results confirm general expectations from the dual string/M-theory picture for strong coupling. In particular, we observe the confined phase in the BFSS matrix model, which is a nontrivial consequence of the M-theory picture. We suggest that these models provide us with an ideal framework to study the Schwarzschild black hole, M-theory, and furthermore, the parameter region of the phase transition between type IIA superstring theory and M-theory. A detailed study of M-theory via lattice Monte Carlo simulations of the D0-brane matrix model might be doable with much smaller computational resources than previously expected.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Evaluation of sustainable waste management: An analysis of techno-economic and life cycle assessments of municipal solid waste sorting and decontamination

This study evaluates the economic and environmental feasibility of Municipal Solid Waste (MSW) sorting and decontamination technologies across urban, suburban, and rural areas. Using Techno-Economic Analysis (TEA) and Life Cycle Assessment (LCA), the research assesses cost-effectiveness and environmental impacts, with a focus on cost variability analyzed through Monte Carlo simulations. Findings indicate significant cost differences based on population density: rural areas incur high costs up to $$764/ton due to low waste volumes and limited infrastructure, whereas suburban and urban areas have more feasible costs ranging from $36.3 to $142.5/ton. Environmental impacts also vary, with greenhouse gas emissions at 171 kg CO 2 eq/ton for copy paper and 118.6 kg CO 2 eq/ton for plastics. PM2.5 levels are 9.1 g/ton for copy paper and 6.3 g/ton for plastics, with sorting lines being the main contributors. Monte Carlo simulations reveal a 50% probability of costs being below $$102.26/ton for copy paper and $115.8/ton for plastics in suburban settings. Further, the study underscores the importance of customized waste management strategies to improve economic viability and sustainability based on local conditions.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

Tau-Jet Matching and Tag-and-Probe Tau Tagging Efficiencies for HH→bbτ+τ− Searches Using Run 3 CMS Scouting Data

We are studying tau-jet matching efficiency and tau tagging efficiency for the search for Higgs boson pair production in the HH→bbτ+τ− decay channel using Run 3 CMS scouting data. Collision events in the CMS detector produce many particle candidates, so jets are clustered using the anti-kT algorithm to identify possible tau signatures. In Monte Carlo simulation, tau-jet matching efficiency can be measured by comparing generated taus to reconstructed jets. In actual collision data, however, generated taus are not available, so we use a tag-and-probe method with Z→τ+τ− candidate events. In this method, one tau candidate is used as the tag and the other as the probe. The invariant mass of the tau-pair candidates is plotted and fitted with signal and background functions to estimate the number of real tau events and determine the tagging efficiency. By comparing efficiencies in data and Monte Carlo simulation, this work helps evaluate the performance of scouting-based tau reconstruction and tau tagging for future HH→bbτ+τ− searches.

Bellot, Annella [North Central Coll.; Fermilab]↗
DOE OSTI2026

Tau-Jet Matching and Tag-and-Probe Tau Tagging Efficiencies for HH→bbτ+τ− Searches Using Run 3 CMS Scouting Data

We are studying tau-jet matching efficiency and tau tagging efficiency for the search for Higgs boson pair production in the HH→bbτ+τ− decay channel using Run 3 CMS scouting data. Collision events in the CMS detector produce many particle candidates, so jets are clustered using the anti-kT algorithm to identify possible tau signatures. In Monte Carlo simulation, tau-jet matching efficiency can be measured by comparing generated taus to reconstructed jets. In actual collision data, however, generated taus are not available, so we use a tag-and-probe method with Z→τ+τ− candidate events. In this method, one tau candidate is used as the tag and the other as the probe. The invariant mass of the tau-pair candidates is plotted and fitted with signal and background functions to estimate the number of real tau events and determine the tagging efficiency. By comparing efficiencies in data and Monte Carlo simulation, this work helps evaluate the performance of scouting-based tau reconstruction and tau tagging for future HH→bbτ+τ− searches.

Bellot, Annella [North Central Coll.; Fermilab]↗
DOE OSTI2021

Sensitive parameter identification and uncertainty quantification for the stability of pipeline conveying fluid

In this study, several uncertainty quantification and sensitivity analysis methods are used to determine the most sensitive geometric and material input parameters of a cantilevered pipeline conveying fluid when uncertainty is introduced to the system at the onset of instability. The full nonlinear equations of motion are modeled using the extended Hamilton’s principle and then discretized using Galerkin’s method. A parametric study is first performed, and the Morris elementary effects are calculated to obtain a preliminary understanding of how the onset speed changes when each parameter is introduced to a ± 5% uncertainty. Then, four different input uncertainty distributions, mainly, uniform and Gaussian distribution, are chosen to investigate how input distributions affect uncertainty in the output. A convergence analysis is used to determine the number of samples needed to maintain simulation accuracy while saving the most computational time. Then, Monte Carlo simulations are run, and the output distributions for each input distribution at ± 1%, ± 3% and ± 5% input uncertainty range are found and discussed. Additionally, the Pearson correlation coefficients are evaluated for different uncertainty ranges. A final Monte Carlo study is performed in which single parameters are held constant while all others still have uncertainty. Overall, the flow speed at the onset of instability is the most sensitive to changes in the outer diameter of the pipe.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Local structure of zinc–indium–tin oxide films via grazing-incidence x-ray pair-distribution functions and theoretical methods

A detailed experimental and theoretical study on the local (r ≤ 4.5 Å) atomic structure of amorphous and crystalline zinc–indium–tin oxide (ZITO) thin films using grazing-incidence x-ray Pair-Distribution Functions (PDFs), ab initio Molecular Dynamics (MD), and Empirical Potential Structure Refinement (EPSR) Monte Carlo simulations is presented. High-energy synchrotron x rays, a two-dimensional detector, and different incident angles were used to probe the depth uniformity of five (ZnO) 0.15 (In 2 O 3 ) 0.70 (SnO 2 ) 0.15 films that were deposited via pulsed-laser deposition at growth temperatures (T G ) ranging from 25 to 300 °C. Films deposited at T G ≤ 150 °C were amorphous. The partially crystalline (T G = 200 °C) and fully crystalline (T G = 300 °C) films were highly textured. Both crystalline and amorphous structures were investigated using ab initio MD and EPSR Monte Carlo simulations. The density of the amorphous films determined from the experimental data agreed with MD calculations. Coordination numbers, bond lengths, and distortion for metal–oxygen and for both the edge- and corner-shared In–metal shells up to 4.5 Å obtained from PDF analysis closely agreed with MD and EPSR simulations. There is a pronounced decrease in the edge- and corner-shared In–Zn distances arising from the shorter Zn–O bond length, Zn–O tetrahedral coordination, and In–O–Zn angle in amorphous ZITO compared to its crystalline counterpart. A maximum in electrical mobility was observed for the amorphous film just before crystallization occurred. While the peak is broad, consistent with nearly unchanged overall cation–oxygen coordination in the amorphous films, ESPR results indicate that the tetrahedral coordination follows the conductivity trend.

Grazing Incidence X-ray↗
DOE OSTI2025

Energy scale and resolution for anti-$k_t$ jets with radius parameters $R$ = 0.2 and 0.6 measured in proton-proton collisions at $\sqrt{s}$ = 13 TeV with the ATLAS detector

Jets with different radius parameters R are an important tool for probing quantum chromodynamics processes at different angular scales. Jets with small R = 0.2 are instrumental in measurements of the substructure of large-R jets resulting from collimated hadronic decays of energetic W, Z, and Higgs bosons, top quarks, and of potential new resonances. This paper presents measurements of the energy scale, resolution, and associated uncertainties of jets with radius parameters R = 0.2 and 0.6, obtained using the ATLAS detector. The results are based on 37 fb -1 of proton–proton collision data from the Large Hadron Collider at a centre-of-mass energy of $\sqrt{s}$ = 13 TeV. A new in situ method for measuring jet energy scale differences between data and Monte Carlo simulations is presented. The systematic uncertainties in the jet energy scale for central jets $(|\eta | < 1.2)$ typically vary from 1% to about 5% as a function of $|\eta |$ at very low transverse momentum, $p_T$ of around 20 GeV for both R = 0.2 and 0.6 jets. The relative energy resolution ranges from (35 ± 6)% at $p_T$ = 20 GeV to (6 ± 0.5)% at $p_T$ = 300 GeV for central R = 0.2 jets, and is found to be slightly worse for R + 0.6 jets. Finally, the effect of close-by hadronic activity on the jet energy scale is investigated and is found to be well modelled by the ATLAS Monte Carlo simulations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Precision measurement of Compton scattering in silicon with a skipper CCD for dark matter detection

Experiments aiming to directly detect dark matter through particle recoils can achieve energy thresholds of $\mathcal{O}(1\,\mathrm{eV})$. In this regime, ionization signals from small-angle Compton scatters of environmental $\gamma$-rays constitute a significant background. Monte Carlo simulations used to build background models have not been experimentally validated at these low energies. We report a precision measurement of Compton scattering on silicon atomic shell electrons down to 23$\,$eV. A skipper charge-coupled device (CCD) with single-electron resolution, developed for the DAMIC-M experiment, was exposed to a $^{241}$Am $\gamma$-ray source over several months. Features associated with the silicon K, L$_{1}$, and L$_{2,3}$-shells are clearly identified, and scattering on valence electrons is detected for the first time below 100$\,$eV. We find that the relativistic impulse approximation for Compton scattering, which is implemented in Monte Carlo simulations commonly used by direct detection experiments, does not reproduce the measured spectrum below 0.5$\,$keV. The data are in better agreement with $ab$$initio$ calculations originally developed for X-ray absorption spectroscopy.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Methodology and Application of Physical Security Effectiveness Based on Dynamic Force-on-Force Modeling

This report describes the research and development being performed at INL towards a dynamic modeling and simulation framework to enable physical security optimization at commercial nuclear power plants. The framework is based on the dynamic modeling tool EMRALD and is demonstrated for applications that can result in physical security optimization. Two main applications are presented: 1. Integrating FLEX portable equipment performance with FOF models of a plant’s physical security posture, and 2. Location optimization of bullet resistant enclosure. The generic framework for modeling FLEX portable equipment is described in detail, followed by a case study modeling an adversarial attack aimed at causing a radiological release by sabotaging the plant’s power supply and its ultimate heat sink capabilities at a hypothetical PWR. Two distinct FLEX deployment strategies, series and parallel, are modeled with distinct timelines. The results of the adversarial attack modeled in a commercial FOF tool, AVERT, are integrated with the FLEX deployment model in EMRALD. Monte Carlo simulation is used to model the distribution of the timeline in FLEX deployment strategies. Thermal-hydraulic analysis of FLEX performance is performed in RELAP5 and integrated with the EMRALD simulations to provide more realistic timelines in the models. The results demonstrate that, even in the extreme case of a successful adversarial attack, deployment of FLEX equipment can result in a significantly high likelihood of preventing radiological release. The modeling and simulation framework of integrating FLEX equipment with FOF models enables the NPPs to credit FLEX portable equipment in the plant security posture, resulting in an efficient and optimized physical security. The objective of location optimization of BRE is to determine the best location in the plant for a new BRE being planned by the plant to enhance their physical security effectiveness. The plant physical security FOF model is integrated with EMRALD that performs Monte Carlo simulation to run different attack scenarios and a discrete set of potential BRE locations. Sensitivity analysis is used to determine the most effective location for the BRE. The optimization approach can be extended to wide applications such as location optimization of remotely operated weapons and other strategic fixed assets.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Variance reduction techniques for Monte Carlo neutron noise simulations

The small fluctuations of the neutron flux caused by small perturbations of the macroscopic cross-sections take the name of neutron noise. Advanced Monte Carlo methods have been recently proposed in order to solve the neutron noise equations in the frequency domain, which allows establishing reference solutions to validate faster but approximate deterministic solvers. Due to the presence of particles carrying two statistical weights (for the real and imaginary components of the noise field), both of which may be positive or negative, Monte-Carlo simulations of neutron noise pose distinct challenges in terms of variance reduction. In this work we investigate two variance-reduction techniques, namely branchless collisions and weight cancellation, and probe their effectiveness for a benchmark con- figuration concerning the noise field induced by a pin with oscillating cross sections in a fuel assembly.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Simulating the Trajectory and Biomass Growth of Free-Floating Macroalgal Cultivation Platforms along the U.S. West Coast

Trajectory tracking and macroalgal growth models were coupled to support a novel macroalgae-harvesting concept known as the Nautical Off-shore Macroalgal Autonomous Device (NOMAD). The NOMAD consists of 5 km long carbon-fiber longlines that are seeded and free float southward along the U.S. West Coast for approximately 3 months before harvesting off the California coast, taking advantage of favorable environmental conditions. The trajectory and macroalgal growth models were applied to answer planning questions pertinent to the techno-economic analysis such as identifying the preferred release location, approximate pathway, timing until harvest, and estimated growth. Trajectories were determined with the General NOAA Operational Modeling Environment (GNOME) model, using 11 years of current and wind data, determining probabilities by running nearly 40,000 Monte Carlo simulations varying the start time and location. An accompanying macroalgal growth model was used to estimate the growth of macroalgae based on the trajectory tracks and environmental forcing products, including light, temperature and nutrients. Model results show that NOMAD lines transit south in the months of April to September due to seasonal currents, taking approximately 3 months to reach Southern California. During transit, NOMAD lines are dispersed but typically avoid beaching or passing through marine sanctuaries. NOMAD lines can yield up to 30 kg wet weight per meter of cultivation line.

09 BIOMASS FUELS↗
DOE OSTI2022

Evaluating Grid Strength under Uncertain Renewable Generation

The increasing displacement of synchronous generators with renewable resources such as wind and solar via power electronic interfaces causes a reduction in short-circuit strength and weak grid issues. The variation and uncertainty of renewable energy increase challenges for identifying weak grid conditions. This paper proposes an efficient method to analyze the impact of uncertain renewable energy on grid strength. The proposed method uses the probabilistic collocation method (PCM) to approximate the results of grid strength assessment under uncertain renewable generation, in order to reduce computational burden without compromising result accuracy when compared with traditional Monte Carlo simulation (MCS). To improve the accuracy of the approximation results, the proposed method integrates the K-means clustering technique with PCM to select the approximation samples of input variables. The efficacy of the proposed method is demonstrated by comparison with MCS on the modified IEEE 9-bus system and modified IEEE 39-bus system with multiple renewable generators.

grid strength↗
DOE OSTI2020

Measurement of space charge effects in the MicroBooNE LArTPC using cosmic muons

Large liquid argon time projection chambers (LArTPCs), especially those operating near the surface, are susceptible to space charge effects. In the context of LArTPCs, the space charge effect is the build-up of slow-moving positive ions in the detector primarily due to ionization from cosmic rays, leading to a distortion of the electric field within the detector. This effect leads to a displacement in the reconstructed position of signal ionization electrons in LArTPC detectors ("spatial distortions"), as well as to variations in the amount of electron-ion recombination experienced by ionization throughout the volume of the TPC. We present techniques that can be used to measure and correct for space charge effects in large LArTPCs by making use of cosmic muons, including the use of track pairs to unambiguously pin down spatial distortions in three dimensions. Finally, the performance of these calibration techniques are studied using both Monte Carlo simulation and MicroBooNE data, utilizing a UV laser system as a means to estimate the systematic bias associated with the calibration methodology.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Rotational Dynamics and Transition Mechanisms of Surface-Adsorbed Proteins

Assembly of biomolecules at solid-water interfaces requires molecules to traverse complex orientation-dependent energy landscapes through processes that are poorly understood, largely due to the dearth of in-situ single molecule measurements and statistical analyses of the rotational dynamics that define directional selection. Emerging capabilities in high-speed atomic force microscopy and machine learning have allowed us to directly determine the orientational energy landscape and observe and quantify the rotational dynamics for protein nanorods on the surface of muscovite mica under a variety of conditions. Comparisons with kinetic Monte Carlo simulations show that the transition rates between adjacent orientation-specific energetic minima can largely be understood through traditional models of in-plane Brownian rotation across a biased energy landscape, with resulting transition rates that are exponential in the energy-barriers between states. However, transitions between more distant angular states are decoupled from barrier height, with jump-size distributions showing a power-law decay that is characteristic of a non-classical Levy-flight random walk, indicating that large jumps are enabled by alternative modes of motion via activated states. The findings provide new insights into the dynamics of biomolecules at solid-liquid interfaces that lead to self-assembly, epitaxial matching and other orientationally anisotropic outcomes and define a general procedure for exploring such dynamics with implications for hybrid biomolecular-inorganic materials design.

Orientational energy landscapes, Rotational dynami↗
DOE OSTI2022

Method of Distributions for Two‐Phase Flow in Heterogeneous Porous Media

Abstract Multiscale heterogeneity and insufficient characterization data for a specific subsurface formation of interest render predictions of multi‐phase fluid flow in geologic formations highly uncertain. Quantification of the uncertainty propagation from the geomodel to the fluid‐flow response is typically done within a probabilistic framework. This task is computationally demanding due to, for example, the slow convergence of Monte Carlo simulations (MCS), especially when computing the tails of a distribution that are necessary for risk assessment and decision‐making under uncertainty. The frozen streamlines method (FROST) accelerates probabilistic predictions of immiscible two‐phase fluid flow problems; however, FROST relies on MCS to compute the travel‐time distribution, which is then used to perform the transport (phase saturation) computations. To alleviate this computational bottleneck, we replace MCS with a deterministic equation for the cumulative distribution function (CDF) of travel time. The resulting CDF‐FROST approach yields the CDF of the saturation field without resorting to sampling‐based strategies. Our numerical experiments demonstrate the high accuracy of CDF‐FROST in computing the CDFs of both saturation and travel time. For the same accuracy, it is about 5 and 10 times faster than FROST and MCS, respectively.

Yang, Hyung Jun↗