Search NASA⌕ Search

SEARCH · Search NASA

Results for “NIOBIUM ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Identification of a new lithium oxide, Li3O2

Lithium oxide (Li3O2) was prepared by decomposing anhydrous lithium hydroxide at 360 C in 48 hours and between 640 and 730 C in times up to 1.3 hours and pressures of about 0.00001 torr. Decompositions were done in nickel, molybdenum, niobium, tantalum, and the T-111 tantalum alloy (Ta - 8-wt.% W - 2 wt.% Hf) containers. This oxide probably belongs to the simple orthorhombic system with the following lattice parameters: a = 108.4 + or - 0.4 nm (10.84 + or - 0.04 A), b = 128.4 + or - 0.5 nm (12.84 + or - 0.05 A), and c = 103.6 + or - 0.4 nm (10.36 + or - 0.04 A).

Stecura, S.↗
NASA NTRS1991

Optical and thermodynamic property measurements of liquid metals and alloys

Optical properties and spectral emissivities of liquid silicon, titanium, niobium, and zirconium were investigated by HeNe laser polarimetry at 632.8 nm. The metals were of a high purity and, except for zirconium, clean. The more demanding environmental requirements for eliminating oxide or nitride phases from zirconium were not met. Containerless conditions were achieved by electromagnetic levitation and heating. CO2 laser beam heating was also used to extend the temperature range for stable levitation and to heat solid silicon to form the metallic liquid phase. Corrections to previously reported calorimetric measurements of the heat capacity of liquid niobium were derived from the measured temperature dependence of its spectral emissivity. Property measurements were obtained for supercooled liquid silicon and supercooling of liquid zirconium was accomplished. The purification of liquid metals and the extension of this work on liquids to the measurement of thermodynamic properties and phase equilibria are discussed.

Weber, J. K. R.↗
NASA NTRSDate not supplied

High-Throughput Strategies that Encompass Experiments and Machine Learning to Predict the Mechanical Properties of Additive Manufactured Aerospace Alloys

Small Punch Test (SPT) uses a thin disk of material to predict mechanical properties. While SPT has existed for decades, it has been used largely as a qualitative evaluator of mechanical properties. Recent advances in computational modeling have enabled the extraction of uniaxial stress-strain response from the measured SPT load-displacement data. Due to small sample volumes and unidirectional testing, SPT is conducive to high-throughput automation and ideally suited to extract properties from high-cost materials. Aerospace alloys have been of recent interest to the Additive Manufacturing (AM) community due to AM’s unique ability to fabricate complex designs not possible, or extremely arduous, with conventional manufacturing. In this research, SPT, coupled with Materials Informatics and computational modeling, is used to develop relevant Process-Structure-Property relationships to decrease the cost and time of process optimization for AM aerospace alloys, namely Inconel 718, Inconel 625, and Niobium C103.

High-throughput Testing↗
NASA NTRS1989

The interface in tungsten fiber reinforced niobium metal-matrix composites

The creep resistance of tungsten fiber reinforced niobium metal-matrix composites was evaluated. The interface region between the fiber and matrix was characterized by microhardness and electron probe microanalysis measurements which indicated that its properties were between those of fiber and matrix. However, the measured properties of the composite exceeded those calculated by the rule of mixtures even when the interface zone was assumed to retain all the strength of the fiber. The composite structure appeared to enhance the strengths of both the fibers and the matrix above what they exhibited in stand-alone tests. The effect of fiber orientation and matrix alloy composition on the fiber/matrix interface were also evaluated. Small alloying additions of zirconium and tungsten to the niobium matrix affected the creep resistance of the composites only slightly. A decrease in the creep resistance of the composite with increasing zirconium content in the matrix was ascribed to an increase in the diffusion rate of the fiber/matrix interdiffusion reaction, and a slight increase in the creep resistance of the composite was observed with an addition of 9 w percent tungsten to the matrix. In addition, Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending on the fiber orientation relative to the stress axis.

Grobstein, Toni L.↗
NASA NTRS1982

The measurement of heats of solution of high melting metallic systems in an electromagnetic levitation field

A method was tested for measuring the enthalpies of mixing of liquid metallic alloying systems, involving the combination of two samples in the electromagnetic field of an induction coil. The heat of solution is calculated from the pyrometrically measured temperature effect, the heat capacity of the alloy, and the heat content of the added sample. The usefulness of the method was tested experimentally with iron-copper and niobium-silicon systems. This method should be especially applicable to high-melting alloys, for which conventional measurements have failed.

Frohberg, M. G.↗
NASA NTRS1981

Containerless undercooling and solidification in drop tubes

A containerless low-gravity environment, produced within a 32 m drop tube apparatus, has been used to undercool and solidify metals, alloys or glasses by eliminating crucible induced nucleation processes. Niobium droplets with diameters in the range of 2 to 5 mm have been undercooled by 525 K which corresponds to the maximum undercooling reported by Turnbull and others on fine dispersions of low melting point metals. Solidification at large undercooling resulted in single crystalline spheres with the formation of interdendritic shrinkage channels on the sample surface rather than interior shrinkage cavities. The grain refinement as observed for Ni samples undercooled and solidified in fused silica crucibles does not occur in free-falling drops of Nb. A calculated solidification speed of undercooled Nb is compared to Ni. A solidification speed of 320 m/s is found for the Nb drops. This solidification speed is greater than or comparable to the solidification speeds calculated in splat cooled samples. Thus, a drop tube apparatus can be useful in the preparation and study of high temperature metastable compounds or alloys in bulk form.

Lacy, L. L.↗
NASA NTRS1988

Microstructures in rapidly solidified niobium aluminides

The microstructures of niobium aluminides produced by chill block melt spinning were compared to those of niobium aluminides produced by conventional casting. The rapidly solidified alloys were rapidly solidified by melt spinning in an argon atmosphere, and the melt-spun ribbons were examined by optical, X-ray, and TEM techniques. Microstructures were found to range from single-phase for Nb-75 at. pct Al (NbAl3) to two phase for Nb-46 at. pct Al (NbAl3 + Nb2Al). It was found that the melt spinning of Nb-aluminides produced finer grained microstructures than those produced in induction-melted ingots or in powders produced by the rotating electrode process. Ternary additions such as Cr, Ti, and Si tended to form intermetallic phases along the grain boundaries.

Hebsur, Mohan G.↗
NASA NTRS1991

Applications of containerless processing in the studies of metals and alloys

The use of containerless processing in nucleation and microstructural studies of alloys is reviewed in terms of approaches and recent results. Drop-tube studies of niobium based on a statistical approach are discussed, and experiments are described which permit the study of the solidification front across the surface of a specimen. The various alloys studied are reviewed in terms of facilitated observations of metastability, chemical homogeneity, and microstructural refinement. Heterogeneous nucleation is reported for a preexponential factor of 10 exp 27 and a critical free energy of 46-56kT. The theoretical relationship between undercooling and solidification velocity correlates with containerless test observations at large solute concentrations. Containerless processing is effective for studying the properties of liquid metals or accessing the metastable thermodynamic regime.

Bayuzick, R. J.↗
NASA NTRS1983

Determination of hydrogen permeability in commercial and modified superalloys

The results of hydrogen permeability measurements on several iron- and cobalt-base alloys as well as on two long-ranged ordered alloys over the range of 705 to 870 C (1300 to 1600 F) are summarized. The test alloys included wrought alloys N-155, IN 800, A-286, 19-9DL, and 19-9DL modifications with aluminum, niobium, and misch metal. In addition, XF-818, CRM-6D, SA-F11, and HS-31 were evaluated. Two wrought long-range ordered alloys, Ni3Al and (Fe,Ni)3(V,Al) were also evaluated. All tests were conducted at 20.7 MPa pressure in either pure and/or 1% CO2-doped H2 for test periods as long as 133 h. Detailed analyses were conducted to determine the relative permeability rankings of these alloys and the effect of doping, exit surface oxidation, specimen design variations, and test duration on permeability coefficient, and permeation activation energies were determined. The two long-range ordered alloys had the lowest permeability coefficients in pure H2 when compared with the eight commercial alloys and their modifications. With CO2 doping, significant decrease in permeability was observed in commercial alloys--no doped tests were conducted with the long-range ordered alloys.

Bhattacharyya, S.↗
NASA NTRS2004

Conductivity of GRCop-42 Alloy Enhanced

GRCop-84, a material developed at the NASA Glenn Research Center, has shown considerable promise for staged combustion rocket engine cycles such as the Space Shuttle Main Engine. However, for an expander cycle rocket engine, the transfer of heat to the fuel is a paramount factor in determining the efficiency of the engine. Examples of current and potential future expander cycle rocket engines are the Pratt & Whitney RL-10, RL-60, and RLX engines. Development of a higher conductivity version of GRCop-84 was undertaken to meet these needs. All expander cycle engines need a main combustion chamber liner with the maximum possible thermal conductivity. In an effort at Glenn to trade some of the greatly increased mechanical properties of GRCop-84 for improved thermal conductivity, the amounts of chromium and niobium were halved. The new Cu-4 at.% Cr-2 at.% Nb alloy was designated GRCop-42.

Ellis, David L.↗
NASA NTRS1987

Superalloy resources: Supply and availability

Over the past several decades there have been shortages of strategic materials because of our near total import dependence on such metals as chromium, cobalt, and tantalum. In response to the continued vulnerability of U.S. superalloy producers to disruptions in resource supplies, NASA has undertaken a program to address alternatives to the super-alloys containing significant quantities of the strategic materials such as chromium, cobalt, niobium, and tantalum. The research program called Conservation of Strategic Aerospace Materials (COSAM) focuses on substitution, processing, and alternate materials to achieve its goals. In addition to NASA Lewis Research Center, universities and industry play an important role in the COSAM Program. This paper defines what is meant by strategic materials in the aerospace community, presents a strategic materials index, and reviews the resource supply and availability picture from the U.S. point of view. In addition, research results from the COSAM Program are highlighted and future directions for the use of low strategic material alloys or alternate materials are discussed.

Stephens, Joseph R.↗
NASA NTRS1989

Resources - Supply and availability

Over the past several decades there have been shortage of strategic materials because of our near total import dependence on such metals as chromium, cobalt, and tantalum. In response to the continued vulnerability of U.S. superalloy producers to disruptions in resource supplies, NASA has undertaken a program to address alternatives to the super-alloys containing significant quantities of the strategic materials such as chromium, cobalt, niobium, and tantalum. The research program called Conservation of Strategic Aerospace Materials (COSAM) focuses on substitution, processing, and alternate materials to achieve its goals. In addition to NASA Lewis Research Center, universities and industry play an important role in the COSAM Program. This paper defines what is meant by strategic materials in the aerospace community, presents a strategic materials index, and reviews the resource supply and availability picture from the U.S. point of view. In addition, research results from the COSAM Program are highlighted and future directions for the use of low strategic material alloys or alternate materials are discussed.

Stephens, Joseph R.↗
NASA NTRS1991

Containerless high temperature property measurements

Containerless processing in the low gravity environment of space provides the opportunity to increase the temperature at which well controlled processing of and property measurements on materials is possible. This project was directed towards advancing containerless processing and property measurement techniques for application to materials research at high temperatures in space. Containerless high temperature material property studies include measurements of the vapor pressure, melting temperature, optical properties, and spectral emissivities of solid boron. The reaction of boron with nitrogen was also studied by laser polarimetric measurement of boron nitride film growth. The optical properties and spectral emissivities were measured for solid and liquid silicon, niobium, and zirconium; liquid aluminum and titanium; and liquid Ti-Al alloys of 5 to 60 atomic pct. titanium. Alternative means for noncontact temperature measurement in the absence of material emissivity data were evaluated. Also, the application of laser induced fluorescence for component activity measurements in electromagnetic levitated liquids was studied, along with the feasibility of a hybrid aerodynamic electromagnetic levitation technique.

Nordine, Paul C.↗
NASA NTRS1979

Process for making a high toughness-high strength iron alloy

A steel alloy is produced by a process which includes using cold rolling at room temperature and subsequent heat treatment at temperatures ranging from 500 C to 650 C. The resulting alloys exhibits excellent strength and toughness characteristics at cryogenic temperatures. This alloy consists essentially of about 10 to 16 percent by weight nickel, to about 1.0 percent by weight aluminum, and 0 to about 3 percent by weight of at least one of the following additional elements: copper, lanthanum, niobium, tantalum, titanium, vanadium, yttrium, zirconium and the rare earth metals, with the balance being essentially iron. The improved alloy possesses a fracture toughness ranging from 200 to 230 ksi sq in. and yield strengths up to 230 ksi.

Stephens, J. R.↗
NASA NTRS1972

High temperature (1200 C) ceramic-to-metal seal development

Two phases have been completed, of a program whose ultimate objective is the development of an alkali metal resistant, thermal shock resistant, leak-tight, and neutron radiation resistant ceramic-to-metal seal capable of operation at 1200 C for three to five years. The first phase involved the screening of platinum-base, vanadium-base and vanadium-niobium base brazes for the joining of Cb-1Zr or T-111 alloys to high purity alumina. The second phase involved studies of the performance of sealed capsule samples during 5000-hour aging tests at 800, 1000, and 1200 C in high vacuum. Sealed capsules which were made using pure vanadium braze, and were brazed at 1850 C for one minute, survived 64 thermal cycles to 1200 C at the heating/cooling rate of 100 C/minute. Vanadium braze samples survived 5000-hour aging tests at 800, 1000, and 1200 C. One thermally cycled sample survived a subsequent 5000-hour aging period at 1000 C, but another, at 1200 C, did not survive. It was concluded that a pure vanadium braze used to bond high purity alumina to Cb-1Zr alloy is the best of the systems studied, but that additional studies must be performed to establish its service temperature limitations for the desired three to five years' service.

Mckisson, R. L.↗
NASA NTRS1979

Mass Driver Two - Cryogenic module

The cryogenic module of Mass Driver Two comprises a 3.25 inch (82.55 mm) OD bucket with two 44 kilo-ampere-turn coils made with .028 inch (.71 mm) diam niobium-titanium multi-filamentary cable in a copper matrix, impregnated with lead alloy for thermal inertia, as well as the service station to refrigerate, energize and eject the bucket. The station is housed in a six inch flanged pyrex cross which connects to the four inch pyrex tube of the mass driver itself. The bucket is refrigerated by being forced against a copper braid cradle attached to the bottom of a liquid helium reservoir which protrudes into the cross from above. The bucket is energized inductively by turning off two superconducting coils which are also attached to the helium reservoir, and which have maintained the correct flux linkage through the bucket coils during their cool-down through the critical temperature. Once charging is completed, the clamping pressure is released and the bucket is injected into the mass driver by means of two normal-conductor pulse coils surrounding the horizontal branches of the cross.

Fine, K.↗