SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Formulations and general procedures are given for making and applying space environmentally, as well as atmospherically stable black silicate paints. Compositions are given which meet spacecraft self-contamination requirements, have excellent heat resistance, and are strongly semiconductive.
Wind tunnel tests were conducted on scale models of the space shuttle orbiter and external tank. The tests were designed to determine the basic heating rate and interference effects on the orbiter-tank configuration and to analyze the effectiveness of the thermal protective system on the reentry vehicle. The phase change paint techniques were used to determine areodynamic heating rates. Oil flow and schlieren photographs were used for flow visualization.
Compositions, formulating procedures, and application techniques are presented for highly reflecting stable white paint coatings suitable for the detection of ultraviolet and visible radiations. For completeness, absolute and relative reflectance data are included for intrasystem and intersystem comparisons.
A performance evaluation was made of two, black nickel coated, flat plate solar collectors. Collector performance was determined under a simulated sun for a wide range of inlet temperatures, including the temperature required for solar powered absorption air conditioning. For a basis of comparison a performance test was made on a traditional, two glass, nonselective, black paint coated, flat plate collector. Performance curves and performance parameters are presented to point out the importance of the design variables which determine an efficient collector. A black nickel coated collector was found to be a good performer at the conditions expected for solar powered absorption air conditioning. This collector attained a thermal efficiency of 50 percent at an inlet temperature of 366 K (200 F) and an incident flux of 946 watts/sq m (300 Btu/hr-sq ft).
Tests were conducted in a hypersonic wind tunnel using various truncated space shuttle orbiter configurations in an attempt to establish the optimum model size for other tests examining body shock-wing leading edge interference effects. The tests were conducted at Mach number 8 using the phase change paint technique. A test description, tabulated data, and tracings of isotherms made from photographs taken during the test are presented.
Model information and data from wind tunnel tests conducted on 0.04 scale 50 percent forebody models of the Space Shuttle Orbiter were presented. These tests were conducted using the phase change paint technique to determine aerodynamic heating rates due to various proturberances and recessions. Angles of attack from 20 deg through 45 deg were investigated at Mach 8.
Post-test information and data are presented from phase change paint, aerodynamic heating wind tunnel tests of a Rockwell International space shuttle orbiter forebody model. These tests were conducted in the Arnold Engineering and Development Center von Karman Facility Tunnel B Hypersonic Wind Tunnel. The purpose of these tests was to determine the effect of simulated orbiter protuberances and penetrations (including RCS nozzles) on aerodynamic heating rates during simulated entry conditions.
Results of aerodynamic heating tests conducted in October 1974 on a space shuttle orbiter model using the phase change paint technique are presented. The model was a 0.040 scale representation of the forward 50 percent of the orbiter. Surface roughness effects on boundary layer transition were investigated. Roughness was simulated by using steel balls varying in diameter from 0 (no balls) to 0.039 inch with 0.040 inch wide by 0.080 inch deep gaps. A nominal Mach number of 8 was tested with Reynolds number varying from 0.75 through 3.5 million per foot. Angle of attack was varied from 20 deg to 40 deg.
Results of a test conducted in the NASA LaRC Mach 8 variable density tunnel to obtain thermal contours on a 0.006 scale model of the configuration 140B Space Shuttle Orbiter are presented using the phase change paint technique. The model was tested at 25 deg, 30 deg, and 35 deg angle of attack at unit Reynolds numbers ranging from 1.0 through 8.0 million per foot. The model was tested with and without a ventral fin mounted on its bottom centerline. Elevon deflections of 0 deg and 10 deg and bodyflap deflections of 0 and 13.75 deg were investigated.
Aerodynamic heating phase change paint tests for the space shuttle orbiter are reported. The model was a 0.040 scale representation of the forward 50% of the orbiter. Surface roughness effects on boundary layer transition were investigated. The roughness was simulated by steel balls 0.020 and 0.025 inch in diameter and a 0.25 in. diameter hole simulating the forward ET attach socket. A nominal Mach number of was tested with unit Reynolds number varying from 0.75 x 1 million ft through 3.5x 1 million ft. Angle of attack was varied from 20 degrees to 40 degrees.
The phase-change coating technique presents itself as a valuable tool in determining the heat transfer rate over the surface of small complex wind tunnel models. A numerical technique is described which shows that an effective thermophysical property - the square root of the product of thermal conductivity, density, and specific heat - may significantly improve the accuracy of the phase-change coating technique with allowance for model inhomogeneity and temperature dependency in a transient environment. Results of the measured steady-state variation of the effective thermophysical property with temperature and the effect of surface heating rate on the effective thermophysical property are plotted for a representative homogeneous model material and for an extreme nonhomogeneous model material. The use of an effective thermophysical property to reduce phase-change paint data is recommended. The analysis also confirms that the apparatus described by Corwin and Kramer (1975) can be used to measure directly this effective thermophysical property for use in wind tunnel model heat-transfer measurements.
Recirculating paint sprayer applies spray of coarse filler in highly volatile solvent. Sprayer was developed for applying insulation material containing epxoy resin, glass fibers, and inert fillers suspended in chlorinated solvents. Sprayer resists abrasive action of fiberglass filler and chemical activity of solvent. Pump and position ensure more uniform pressure at spray gun without backpressure regulator, which tended to clog in old sprayer.
Eddy-current flaw detector with cathode-ray tube (CRT) used to compare layer thickness of conductive paint on metallic substrates.
Highly reflective, diffused coatings developed by incorporating polytetrafluoroethylene (TFE) pigment with alcohol-soluble binders. Alcohol and binder mixed together in blender before adding TFE. TFE preferably outgassed in mechanical-pump vacuum for typical interval of 4 hours before adding to liquid. Like wetting agent, vacuum treatment helps to prevent clumping of TFE and eases dispersion throughout mixture. Mixture blended for 3 to 5 minutes before used. Coatings useful on reflectance-standard surfaces for calibrating radiometric instruments in both laboratory and field. Paints washable and usable as optical reference surfaces.
An experimental investigation was performed in the NASA/Ames Research Center 3.5-foot Hypersonic Wind Tunnel to obtain supersonic heat-distribution data in areas between the orbiter and external tank using phase-change paint techniques. The tests used Novamide SSV Model 56-OTS in the first and second-stage ascent configurations. Data were obtained at a nominal Mach number of 5.3 and a Reynolds number per foot of 5 x 10 to the 6th power with angles of attack of 0 deg, +/- 5 deg, and sideslip angles of 0 deg and +/- 5 deg.
Resistor-and-capacitor circuit models represent evolving properties of coated specimens. Electrochemical experiments on corrosion of painted 4130 steel described in report. Study part of general development of ac-impedance method for measurement of properties of coated metals.
Measurements of optical properties and surface characterization of paint discs on selected tray clamps were carried out and are reported. Analysis shows the loss of organic binder for those specimens exposed to atomic oxygen. A visibly darkened layer up to 2 microns thick exists on the outer surfaces of specimens exposed only to solar radiation. Properties of ground control specimens and flight control specimens, as a function of spacecraft location are reported. Representative examples from a photomicrograph survey and SEM examination are shown.
Technique developed to reduce data quickly and objectively in images of phase-change paints. Involves use of three-tube color-camera system. Camera modified so separate red (R), green (G), and blue (B) video outputs contain complete framing information recorded and digitized by use of standard video format. Proven very simple and repeatable. Used wherever rapid and accurate remote temperature-profile measurements desired; for example, for test objects in inaccessible, toxic, or other hostile areas.