Search NASA⌕ Search

SEARCH · Search NASA

Results for “Partial oxidation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Influence of temperature, oxygen partial pressure, and microstructure on the high-temperature oxidation behavior of the SiC Layer of TRISO particles

Tristructural isotropic (TRISO)-coated fuel particles are designed for use in high-temperature gas-cooled nuclear reactors, featuring a structural SiC layer that may be exposed to oxygen-rich environments over 1000 °C. Surrogate TRISO particles were tested in 0.2–20 kPa O 2 atmospheres to observe the differences in oxidation behavior. Oxide growth mechanisms remained consistent from 1200–1600 °C for each P O$_2$ , with activation energies of 228 ± 7 kJ/mol for 20 kPa O 2 and 188 ± 8 kJ/mol for 0.2 kPa O 2 . At 1600 °C, kinetic analysis revealed a change in oxide growth mechanisms between 0.2 and 6 kPa O2. In 0.2 kPa O 2 , oxidation produced raised oxide nodules on pockets with nanocrystalline SiC. Oxidation mechanisms were determined using Atom probe tomography. Active SiC oxidation occurred in C-rich grain boundaries with low P O$_2$ , leading to SiO 2 buildup in porous nodules. Here, this phenomenon was not observed at any temperature in 20 kPa O 2 environments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Persistent and partially mobile oxygen vacancies in Li-rich layered oxides

Increasing the energy density of layered oxide battery electrodes is challenging as accessing high states of delithiation often triggers voltage degradation and oxygen release. Here we utilize transmission-based X-ray absorption spectromicroscopy and ptychography on mechanically cross-sectioned Li 1.18–x Ni 0.21 Mn 0.53 Co 0.08 O 2–δ electrodes to quantitatively profile the oxygen deficiency over cycling at the nanoscale. The oxygen deficiency penetrates into the bulk of individual primary particles (~200 nm) and is well-described by oxygen vacancy diffusion. Using an array of characterization techniques, we demonstrate that, surprisingly, bulk oxygen vacancies that persist within the native layered phase are indeed responsible for the observed spectroscopic changes. We additionally show that the arrangement of primary particles within secondary particles (~5 μm) causes considerable heterogeneity in the extent of oxygen release between primary particles. Finally, our work merges an ensemble of length-spanning characterization methods and informs promising approaches to mitigate the deleterious effects of oxygen release in lithium-ion battery electrodes.

25 ENERGY STORAGE↗
DOE OSTI2024

Drying and Analysis of Aluminum (Oxy)hydroxide Films for Dry Storage of Aluminum-Clad Spent Nuclear Fuels

In aluminum-clad spent nuclear fuels, an (oxy)hydroxide layer on the surface of the cladding hosts chemisorbed water formed during reactor and post-discharge exposure to water. Any residual water is susceptible to generating hydrogen via radiolysis, which can be a risk associated with dry fuel storage. Engineering-scale forced helium dehydration (FHD) and vacuum drying tests were conducted on mock-up fuel assemblies that included corroded aluminum surrogate plates to assess the removal of bulk and chemisorbed water. Thermogravimetric analysis was performed on samples of the surrogate plates, both undried control samples used to determine onset temperatures associated with a phase change occurring in the oxide layer and samples from drying tests used to determine the effectiveness of each drying method. Both vacuum drying and FHD processes were capable of removing bulk water. However, FHD was determined to provide additional drying capabilities, including partial removal of chemisorbed water from bayerite due to the higher temperatures during drying. In conclusion, the temperature threshold for partial dehydroxylation of the oxide layer was determined to be around 220°C, meaning any drying methods attempting to remove chemisorbed water must exceed 220°C.

chemisorbed water↗
DOE OSTI2026

Activating magnetite ores for aqueous ironmaking at high current densities

Low-temperature electrochemical cells reducing iron oxides to metal in alkaline electrolytes can support fully electrified steelmaking processes. Previous studies on these cells have primarily focused on high-surface-area hematite, Fe 2 O 3 , reactants whereas attempts to reduce suspensions of magnetite, Fe 3 O 4 —one of the two feedstocks for existing ironmaking reactors—have generally been limited to low rates of reaction (<30 mA cm −2 ). Here, in this study, we control the crystalline domain size of Fe 2 O 3 and Fe 3 O 4 particles in 10 M NaOH electrolytes to study how the nanoscale morphology of oxides controls the rate of electrochemical ironmaking. Rotating-ring disk electrode measurements of Fe 2+ , in situ Raman spectroscopy of the electrode surface, and ex situ electron microscopy were consistent with a hypothesized passivation process at Fe 3 O 4 surfaces that may prevent the continuous formation of soluble intermediates. Sufficiently small (<100 nm diameter) oxide particles yielded Fe partial current densities >160 mA cm −2 , a fivefold increase relative to previously reported rates for Fe 3 O 4 suspensions and comparable to active Fe 2 O 3 . Electron microscopy revealed that electrodeposited films were composed of micron-scale crystalline Fe domains with a porous film of Fe 3 O 4 nanoparticles and supports a model where Fe is grown primarily from soluble Fe 2+ intermediates. Based on these insights, inactive blast-furnace-grade iron-oxides were transformed into high surface area nanoparticles (1.6 to 229.2 m 2 g −1 ) via reprecipitation, leading to a ninefold enhancement in faradaic efficiency and an Fe partial current density of 120 mA cm −2 . When integrated with chlor-iron cells producing reagents for reprecipitation, this approach could lead to a cost-competitive process for electrochemical ironmaking from industrially relevant feedstocks.

TEM↗
DOE OSTI2023

Direct Mapping of Fluorine in Cation Disordered Rocksalt Cathodes

Cation-disordered rocksalt (DRX) oxides are promising candidates as next-generation cathodes for lithium-ion batteries. Partial fluorination of the DRX oxides enhances their cyclability. However, the lattice position, concentration, and spatial distribution of fluorine within DRX lattices remain elusive. Here, in this work, we use atom location by channeling-enhanced microanalysis, energy-dispersive X-ray spectroscopy, electron energy loss spectroscopy, and integrated differential phase contrast imaging in a scanning transmission electron microscope to gain atomic-level insights into DRX with nominal composition of Li 1.2 Mn 0.7 Ti 0.1 O 1.7 F 0.3 and Li 1.15 Ni 0.45 Ti 0.3 Mo 0.1 O 1.85 F 0.15 . We reveal that fluorine substitutes oxygen in the DRX lattices. The O/F ratio in terms of O+F = 2 is in the range from 1.92:0.08 to 1.82:0.18. Spatially, fluorine is distributed in the proximity of the Li-rich regions but distinct from lithium fluoride. Additionally, we observe that incorporation of fluorine in the DRX lattice induces a larger variation in cation–anion separation. These observations provide insight into the guided design of oxyfluoride DRX cathodes for high-performance batteries.

(S)TEM↗
DOE OSTI2022

Mesolytic cleavage of homobenzylic ethers for programmable end-of-life function in redoxmers

Irreparable chemical damage to redox-active monomers, oligomers, and polymers (i.e. redoxmers) limits the lifetime of energy storage devices (e.g. redox flow batteries) by causing electrode and membrane fouling, as well as irreversible capacity loss. To predictably restore device and materials performance, it is desirable to add programmed destruction capabilities into these damage-prone materials. Here, we report the use of triggerable retrograde reactions to achieve programmable end-of-life function in redoxmers. Retrograde reactions are intended to break up damaged redoxmer materials into more soluble small-molecule constituents to prevent irreparably fouling battery interfaces. We investigated the redox-triggered mesolytic cleavage of homobenzylic ethers (HBEs) for this purpose. Combining experimental methods with simulations, we probed the influence of ring substituents on the programmable bond-scission behavior of HBEs. Variation of para-substituents on the HBEs allowed us to modify the oxidation potential, degradation pathway, and electrochemical mechanisms of the generated products. Given its ideal oxidation potential, we selected the para-methoxy-based HBE as the cleavage scaffold and integrated it with dialkoxybenzene, TEMPO, viologen, and para-nitrobenzene redox centers for compatibility, bulk deconstruction, and electrode defouling tests. Upon applying a high oxidation potential, the redox-active pendant is cleaved from the backbone via HBE bonds; of the four redox centers tested, three of them remained fully redox active. Viologen-appended redox active polymers with HBE linkers were cleaved to fully separate the redox centers from the backbone. Polymer-filmed electrodes were partially restored following HBE oxidation defouling. Here these studies highlight the co-design of new materials functions for developing sustainable energy storage materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Modeling Interactive Effects of Manganese Bioavailability, Nitrogen Deposition, and Warming on Soil Carbon Storage

Manganese (Mn) is a redox–active micronutrient that has been shown to accelerate plant litter decomposition; however, the effect of Mn–promoted decomposition on soil C storage is unclear. We present a novel biogeochemical model simulating how Mn bioavailability influences soil organic C (SOC) stocks in a soil profile (<50 cm) within a temperate forest. In our model, foliar Mn increased in response to increasing soluble Mn released through Mn–oxide (birnessite) dissolution in mineral soil layers. The ensuing Mn enrichment in leaf litter redistributed Mn to the surface forest floor layer, promoted enzymatic oxidation of lignin, and decreased SOC stocks. Total SOC loss was partially mitigated by accumulation of lignin–oxidation products as mineral–associated organic C. We also explored how Mn–driven changes to C storage interacted with effects of N deposition and warming. Nitrogen enrichment inhibited Mn–dependent lignin degradation, increasing SOC stocks and weakening their dependence on Mn bioavailability. Warming stimulated decomposition and reduced C stocks but was less effective at low Mn bioavailability. Our model results suggest that SOC stocks are sensitive to Mn bioavailability because increased plant uptake redistributes Mn to surface soils where it can enhance litter decomposition. Finally, based on our simulations, we predict that Mn becomes limiting to litter decomposition where Mn is poorly soluble. Depletion of bioavailable Mn or other cofactors that are critical to decomposition could limit the response of organic C stocks to warming over time, but quantitative projections of the role of Mn bioavailability in regulating decomposition requires additional measurements to constrain model uncertainties.

58 GEOSCIENCES↗
DOE OSTI2022

Radically Engineered Modular Air Separation System with Tailored Oxygen Sorbents

The commercial energy sector relies heavily on fossil fuel conversion, and in the process releases a significant amount of CO 2 . A promising technology to utilize fossil fuels with relatively affordable CO 2 capture is gasification. However, it requires a pure oxygen stream. The current state of the art method to produce oxygen is cryogenic air separation, which supercools air to a liquid, and then using distillation columns to separate the components. While this method has been thoroughly studied, it only has a 25% efficiency from a second law standpoint and therefore requires a significant amount of energy (and associated emissions) for oxygen production. This, then, lowers the incentive for carbon capture within a plant, so alternative methods need to be investigated. One potential method, chemical looping air separation (CLAS), is a promising method to replace state of the art oxygen generation technologies. CLAS utilizes a cyclic redox scheme with an oxygen sorbent to create pure oxygen streams. This approach typically utilizes a dual reactor scheme where the oxygen deficient sorbent enters the first reactor and is subjected to high oxygen partial pressures to re-oxidize the sorbent. Then the sorbent is sent to the reducing reactor, where it is subjected to low oxygen partial pressure (steam or vacuum) to releases oxygen. The overarching objective of this project was to discover the principles for rational design and optimization of oxygen sorbents and process design to ensure the process is a viable replacement for cryogenic air separation, especially in the context of modular gasification systems. This was done through development, characterization, testing, and analyses of (a) high temperature mixed composite oxides; (b) low temperature doped perovskite oxides (A1 x A2 1-x B1 y B2 1-y O 3 ); (c) scale up synthesis and testing of the optimized sorbent particles; (d) process design and analyses of the CLAS system in the context of modular gasification applications.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Visualizing Oxidation Mechanisms in Few-Layered Black Phosphorus via In Situ Transmission Electron Microscopy

Layered two-dimensional (2D) black phosphorus (BP) exhibits novel semiconducting properties including a tunable bandgap and high electron mobility. However, the poor stability of BP in ambient environment severely limits potential for application in future electronic and optoelectronic devices. While passivation or encapsulation of BP using inert materials/polymers has emerged as a plausible solution, a detailed fundamental understanding of BP's reaction with oxygen is imperative to rationally advance its use in applications. Here, we use in situ environmental transmission electron microscopy to elucidate atomistic structural changes in mechanically exfoliated few-layered BP during exposure to varying partial pressures of oxygen. An amorphous oxide layer is seen on the actively etching BP edges, and the thickness of this layer increases with increasing oxygen partial pressure, indicating that oxidation proceeds via initial formation of amorphous P x O y species which sublime to result in the etching of the BP crystal. We observe that while few-layered BP is stable under the 80 kV electron beam (e-beam) in vacuum, the lattice oxidizes and degrades at room temperature in the presence of oxygen only in the region under the e-beam. The oxidative etch rate also increases with increasing e-beam dosage, suggesting the presence of an energy barrier for the oxidation reaction. Preferential oxidative etching along the [0 0 1] and [0 0 1] crystallographic directions is observed, in good agreement with density functional theory calculations showing favorable thermodynamic stability of the oxidized BP (0 0 $\bar{1}$) planes compared to the (1 0 0) planes. Finally, we expect the atomistic insights and fundamental understanding obtained here to aid in the development of novel approaches to integrate BP in future applications.

2D materials↗
DOE OSTI2026

MoS 2 Catalysts Selectively Achieve High Yield of Liquid Oxygenate from Direct Conversion of Methane via Hydroxyl Radicals

Directly converting methane (CH 4 ) into liquid oxygenates (e.g., methanol) can circumvent the cost and engineering limits of natural gas transportation and storage. However, oxygenate yields from CH 4 remain low, and sulfur present in natural gas hinders activity in most catalysts. Here, to overcome these barriers, we employ bulk molybdenum disulfide (MoS 2 ), a low-cost, robust catalyst which selectively produces large quantities of liquid oxygenates (>900 µmol/g cat ∙hr) from methane in the presence of hydroxyl (OH • ) radicals produced from dilute hydrogen peroxide (H 2 O 2 ) at 75°C. Under realistic reaction conditions, MoS 2 partially and reversibly adopts a metastable, more electrically conductive phase (1T’) that can only be observed through in situ structural probes. Herein, we elucidate that redox synergy between H 2 O 2 and MoS 2 produces active OH • radical species that selectively transform CH 4 to surface methoxy species at the gas-solid liquid interface, leading to the unitary production of liquid oxygenate at a rate competitive with more costly precious metal catalysts, without additional catalyst preparation steps.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High Capacity Adsorption—Dominated Potassium and Sodium Ion Storage in Activated Crumpled Graphene

In this study, structurally and chemically defective activated-crumbled graphene (A-CG) is employed to achieve unique synergy of large reversible potassium (K) and sodium (Na) ion storage capacity with fast charging and extended cyclability. A-CG synthesis consists of low temperature spraying of graphene oxide slurry, followed by partial reduction annealing and air activation. For K storage, the reversible capacities are 340 mAh g -1 at 0.04 A g -1 , 261 mAh g -1 at 0.5 A g -1 , and 210 mAh g -1 at 2 A g -1 . For Na storage, the reversible capacities are 280 mAh g -1 at 0.04 A g -1 , 191 mAh g -1 at 0.5 A g -1 , and 151 mAh g -1 at 2 A g -1 . A-CG shows a stable intermediate rate (0.5 Ag -1 ) cycling with both K and Na, with minimal fade after 2800 and 8000 cycles. These are among the most favorable capacity—rate capability—cyclability combinations recorded for potassium-ion battery and sodium-ion battery carbons. Electroanalytical studies (cyclic voltammetry, galvanostatic intermittent titration technique, b -value) and density functional theory (DFT) reveal that enhanced electrochemical performance originates from ion adsorption at various defects, such as Stone–Wales defects. Moreover, DFT highlights enhanced thermodynamic stability of A-CG with adsorbed K versus with adsorbed Na, explaining the unexpected higher reversible capacity with the former.

25 ENERGY STORAGE↗
DOE OSTI2023

Adapting an Electron Microscopy Microheater for Correlated and Time-Resolved Ambient Pressure X-ray Photoelectron Spectroscopy

Environmental transmission electron microscopy (ETEM) can follow structural and chemical changes in nanomaterials under reaction conditions, including at temperatures up to 1300 °C and pressures up to ~20 mbar. However, ETEM studies are limited to localized areas of a sample and can benefit from correlative studies of a similar sample on larger length scales. Here, in this work, we describe the customization of a commercial microheater holder used in ETEM to anode-based ambient pressure X-ray photoelectron spectroscopy (APXPS), where chemical and electronic structure information is averaged over several hundred square micrometers. To benchmark heating capabilities in the APXPS instrument, core level binding energies were followed during surface chemical reactions of a Pd film, including CO adsorption–desorption, Pd oxidation, and PdO reduction. The fast heating feature of the microheaters advanced XPS experimental capabilities, including the collection of subsecond time-resolved spectra of the Pd 3d 5/2 peak during the reduction of an oxidized Pd film. The potential to use these heaters in a closed gas cell was also demonstrated by oxidizing Pd in a partial pressure of air locally dosed to the sample surface. General tips and considerations for the application of commercial ETEM heaters to any XPS system with a focused X-ray beam are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Facile Synthesis of Oxyhydrides by Reaction with NaBH 4 in an Open System

Oxyhydrides are an intriguing class of materials in which there is partial replacement of the oxide ion with hydride ions and oxygen vacancies. Conventional synthesis relies on vacuum sealed ampules, using long reaction times at high temperatures, limiting accessibility. Here, we demonstrate a rapid, ambient-pressure route to oxyhydride formation using NaBH 4 under flowing argon in just 1 h. This approach significantly lowers experimental barriers, enabling broader exploration of these materials. The maximum hydride incorporation, obtained using a reaction temperature of 400 °C, is given by the formula SrTiO 2.945 H 0.049 , where the hydride, oxygen vacancy, and unpaired electron concentrations are determined through thermogravimetric analysis, quantitative solid-state nuclear magnetic resonance (NMR) spectroscopy, and electron paramagnetic resonance (EPR) spectroscopy. Density functional theory simulations of the 1 H NMR shifts for candidate point defects support the assignment of the observed hydride peak, validating the efficacy of the synthetic approach. A combination of in situ and ex situ studies of the reaction pathway reveal that hydride incorporation into the perovskite occurs via direct solid-solid reaction, with higher reaction temperatures favoring NaBH 4 decomposition and H 2 (g) release over oxyhydride formation. The electronic defect structure established from the EPR and NMR studies indicate that, at ambient temperature, anion vacant sites are occupied by single electrons, whereas hydride sites do not trap electrons. As a result, this work establishes a scalable synthesis strategy and provides a computational-experimental framework for understanding defect chemistry in oxyhydrides, opening pathways for their integration into energy and electronic applications.

Anions↗
DOE OSTI2024

Effects of Halides on Organic Compound Degradation during Plasma Treatment of Brines

Plasma has been proposed as an alternative strategy to treat organic contaminants in brines. Chemical degradation in these systems is expected to be partially driven by halogen oxidants, which have been detected in halide-containing solutions exposed to plasma. In this study, we characterized specific mechanisms involving the formation and reactions of halogen oxidants during plasma treatment. Here, we first demonstrated that addition of halides accelerated the degradation of a probe compound known to react quickly with halogen oxidants (i.e., para -hydroxybenzoate) but did not affect the degradation of a less reactive probe compound (i.e., benzoate). This effect was attributed to the degradation of para-hydroxybenzoate by hypohalous acids, which were produced via a mechanism involving halogen radicals as intermediates. We applied this mechanistic insight to investigate the impact of constituents in brines on reactions driven by halogen oxidants during plasma treatment. Bromide, which is expected to occur alongside chloride in brines, was required to enable halogen oxidant formation, consistent with the generation of halogen radicals from the oxidation of halides by hydroxyl radical. Other constituents typically present in brines (i.e., carbonates, organic matter) slowed the degradation of organic compounds, consistent with their ability to scavenge species involved during plasma treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Exsolution-Driven Surface Transformation in the Host Oxide

Exsolution synthesizes self-assembled metal nanoparticle catalysts via phase precipitation. An overlooked aspect in this method thus far is how exsolution affects the host oxide surface chemistry and structure. Such information is critical as the oxide itself can also contribute to the overall catalytic activity. Here, combining X-ray and electron probes, we investigated the surface transformation of thin-film SrTi 0.65 Fe 0.35 O 3 during Fe 0 exsolution. We found that exsolution generates a highly Fe-deficient near-surface layer of about 2 nm thick. Moreover, the originally single-crystalline oxide near-surface region became partially polycrystalline after exsolution. Such drastic transformations at the surface of the oxide are important because the exsolution-induced nonstoichiometry and grain boundaries can alter the oxide ion transport and oxygen exchange kinetics and, hence, the catalytic activity toward water splitting or hydrogen oxidation reactions. These findings highlight the need to consider the exsolved oxide surface, in addition to the metal nanoparticles, in designing the exsolved nanocatalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development and Testing of an Integrated Acid Mine Drainage (AMD) Treatment and Rare Earth/Critical Mineral Plant

The overall objective of this project was to design, construct, and test a pilot-scale continuous process for efficiently treating acid mine drainage (AMD) while producing rare earth element/critical mineral (REE/CM) concentrates. The process technology evaluated in this project included two distinct operations: 1. an upstream pre-concentration unit that treats raw AMD to environmentally compliant discharge standards while capturing an REE/CM preconcentrate, and 2. a downstream REE purification process that further enriches the pre-concentrate while producing mixed or partially separated rare earth oxides (REOs). The project team members successfully completed all of the proposed goals of the project and advanced the technology readiness levels (TRL) of the constituent operations to TRL 7 for the upstream concentration unit (full-scale system demonstration) and TRL 6 for the downstream purification process (pilot-scale demonstration).

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

New Solids in As-O-Mo, As(P)-O-Mo(W) and As(P)-O-Nb(W) Systems That Exhibit Nonlinear Optical Properties

Interactions between well-mixed fine powders of As 2 O 3 , P 2 O 5 , MoO 3 , WO 3 and Nb 2 O 5 at different stoichiometry in quartz ampoules under vacuum at ~1000 °C in the presence of metallic molybdenum (or niobium), over several weeks, led to shiny dichroic crystalline materials being formed in cooler parts of the reaction vessel. An addition of small quantities of metals-Mo or Nb-was made with the aim of partially reducing their highly oxidized Mo(VI), W(VI) or Nb(V) species to corresponding Mo(V), W(V) and Nb(IV) centers, in order to form mixed valence solids. Sublimed crystals of four new compounds were investigated using a variety of techniques, with prime emphasis on the X-ray analysis, followed by spectroscopy (diffusion reflectance, IR, Raman and EPR), second harmonic generation (SHG), thermal analysis under N 2 and air atmosphere, and single crystals electrical conductivity studies. The results evidenced the formation of new complex solids of previously unknown compositions and structures. Three out of four compounds crystallized in non-centrosymmetric space groups and represent layered 2D polymeric puckered structures that being stacked on each other form 3D lattices. All new solids exhibit strong second-harmonic-generation (SHG effect; based on YAG 1064 nm tests with detection of 532 nm photons), and a rare photosalient effect when crystals physically move in the laser beam. Single crystals’ electrical conductivity of the four new synthesized compounds was measured, and the results showed their semiconductor behavior. Values of band gaps of these new solids were determined using diffusion reflectance spectroscopy in the visible region. Aspects of new solids’ practical usefulness are discussed.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Selective Conversion of CO 2 to Methanol on a In 2 O 3– x –TiO 2 (110) Interface: Importance of Oxide–Oxide Interactions

Methanol is a strategic energy vector for the storage and delivery of energy and is a widely used precursor for the synthesis of many high-value chemicals. The hydrogenation of carbon dioxide (CO 2 ) into methanol is a key process in industrial operations. Here, in this study, we show that an oxide-oxide interface generated by a low loading (0.15 ML) of In 2 O 3-x on a TiO 2 (110) substrate has a high activity and selectivity as a catalyst for the CO 2 + 3H 2 → CH 3 OH + H 2 O process. The properties of the In 2 O 3-x -TiO 2 interface under reaction conditions were investigated using a combination of synchrotron-based ambient pressure X-ray photoelectron spectroscopy (AP-XPS), temperature programmed desorption (TPD), and catalytic testing. The In 2 O 3-x overlayer spread out on top of the titania and was rich in defects and O vacancies that activated CO 2 and H 2 as reactants, without destroying CH 3 O and CH 3 OH as reaction products. The In 2 O 3-x /TiO 2 (110) catalyst is at least one order of magnitude more active than bulk indium oxide while maintaining a very high selectivity (~80%) towards methanol production. Under the rich hydrogen environment of methanol synthesis, the oxide-oxide interactions allowed only a partial reduction of the In cations, preventing the formation of metal alloys as seen in the case of catalysts with metal-indium oxide interfaces. Thus, the dispersion of low loadings of In 2 O 3-x on a stable oxide substrate is a valid and low-cost approach for generating efficient catalysts for CO 2 valorization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗