Search NASA⌕ Search

SEARCH · Search NASA

Results for “Periodic Heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Neuromorphic heat transport effects in a molecular junction

Understanding energy transport at the nanoscale is an open and fundamental challenge in the molecular sciences with direct implications for the design of new electronics, computing devices, and materials. While nanoscale energy transport under steady-state conditions has been studied extensively, there is much less known about energy transport under time-dependent driving forces, particularly in the far-from-equilibrium regime. In this work, we use nonequilibrium molecular dynamics simulations and stochastic thermodynamics to investigate energy transport in a well-studied nanoscale system—a molecular junction—subjected to a time-periodic temperature gradient. The primary observation is that molecular junctions can exhibit heat transport hysteresis, a phenomenon in which the heat flux through a system depends not only on the instantaneous value of a time-dependent temperature bias but also on the temporal history of that bias. The presented findings illustrate that molecular junctions can exhibit the specific memory effect—heat transport hysteresis—that is essential for the design of thermal neuromorphic computers. This work elucidates a potential pathway toward the realization of such devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Reactor physics characterization of triply periodic minimal surface-based nuclear fuel lattices

Triply periodic minimal surface (TPMS) lattices are receiving substantial attention in numerous engineering fields due to their impressive topology-driven physical characteristics. TPMS lattices are periodic structures of two distinct intertwined volume domains separated by an area-minimizing surface or wall. TPMS lattices have been observed in nature, such as biological membranes, skeletons, block copolymers, sea urchins, butterfly wings, and equipotential surfaces in crystals. Intriguingly, the topology of TPMS lattices can be easily parametrized via level-set equations and thus are heavily numerically and experimentally studied. Here, a significant research effort is currently applying TPMS lattices for heat exchangers and sinks. This paper extends TPMS lattice applications to nuclear reactor fuel designs, with a focus on identifying relevant TPMS geometric parameters controlling neutronics characteristics, such as reactivity, neutron spectrum, and heat removal properties. We found that fuel surface-area-to-volume ratios for TPMS lattices can be two orders of magnitude larger than current cylindrical fuel rods. Further, the selected TPMS lattice and its implicit equation, the unit cell pitch, wall thickness, and structure porosity are design parameters enabling neutronics optimization for both thermal and fast spectrum configurations, paving the way for exceptionally compact and dense nuclear core concepts.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Robust silane self-assembled monolayer coatings on plasma-engineered copper surfaces promoting dropwise condensation

Dropwise condensation is well known to result in better heat transfer performance owing to efficient condensate/droplet removal, which can be harnessed in various industrial heat/mass transfer applications such as power generation and conversion, water harvesting/desalination, and electronics thermal management. The key to enhancing condensation via the dropwise mode is thin low surface energy coatings (<100 nm) with low contact angle hysteresis. Ultrathin (<5 nm) silane self-assembled monolayers (or SAMs) have been widely studied to promote dropwise condensation due to their minimal thermal resistance and scalable integration processes. Such thin coatings typically degrade within an hour during condensation of water vapor. After coating failure, water vapor condensation transitions to the inefficient filmwise mode with poor heat transfer performance. We enhance silane SAM quality and durability during water vapor condensation on copper compared to state-of-the-art silane coatings on metal surfaces. We achieve this via (i) surface polishing to sub-10 nm levels, (ii) pure oxygen plasma surface treatment, and (iii) silane coating integration with the copper substrate in an anhydrous/moisture-free environment. The resulting silane SAM has low contact angle hysteresis (≈20°) and promotes efficient dropwise condensation of water for >360 hours without any visible sign of coating failure/degradation in the absence of non-condensable gases. We further demonstrate enhanced heat transfer performance (≈5-7× increase over filmwise condensation) over an extended period of time. Surface characterization data post-condensation leads us to propose that in the absence of non-condensable gases in the vapor environment, the silane SAM degrades due to reduction and subsequent dissolution of copper oxide at the oligomer-substrate interface. The experiments also indicate that the magnitude of surface subcooling (or condensation rate) affects the rate of coating degradation. Finally, this work identifies a pathway to durable dropwise promoter coatings that will enable efficient heat transfer in industrial applications.

42 ENGINEERING↗
DOE OSTI2025

Preliminary modeling of triply periodic minimal surface (TPMS) structures using RELAP5-3D

With the United States Department of Energy (DOE)’s goal of quadrupling the nation’s nuclear energy supply by 2050, and with the Advanced Fuels Campaign pushing for new types of advanced reactor fuels and geometries, the need has arisen for new nuclear fuel designs. One such design is to swap out current nuclear fuel geometries in exchange for another type of geometry, called a Triply Periodic Minimal Surface (TPMS). TPMSs are self-supporting, infinitely repeating lattices—attributes that lend themselves well to additive manufacturing. These surfaces also possess enhanced heat transfer properties thanks to their internal area changes and large surface-area-to-volume ratios. Their drawback, however, is an increased pressure drop. Given the small amount of correlations and data (Reynolds numbers in the 2,000–8,000 range), and the minimal amount of experience so far obtained by modeling TPMS structures using 1D systems codes such as the Reactor Excursion and Leak Analysis Program (RELAP5-3D), further research into this topic was needed. Using data from the University of Wisconsin - Madison (UW), curve fits were created for both a Heat Transfer Coefficient (HTC) correlation and a Darcy friction factor empirical coefficient correlation. The curves’ coefficients and multipliers were then output and utilized in RELAP5-3D models of two upcoming experiments—Flow Loop for INFLUX Pressure drop (FLIP) and Microreactor Agile Non-nuclear Experimental Test (MAGNET)—aimed at increasing the available data for Reynolds numbers to the 16,000–36,000 range for TPMS structures. The models were run under the conditions utilized by a Computational Fluid Dynamics (CFD) analysis performed by another group at Idaho National Laboratory. Only CFD pressure drop values were obtained from the FLIP test, and those values showed that the RELAP5-3D models had a lower rate of pressure increase in comparison to the CFD values. In addition, there seemed to be a vertical shift upward in the pressure drop for both models whenever the TPMS porosity decreased, and the RELAP5-3D models showed a higher vertical shift in comparison to the CFD values. The MAGNET results did not correspond to any CFD or experimental results against which they could be compared, so they were instead compared against the proposed CFD input conditions. These values were then compared with each other to make sure the model seemed to be performing as expected, paving the way for future tests that can be run for the purpose of further analyses and comparisons. The pressure drop increased with temperature and mass flow rate independently. The temperature change would decrease with increasing mass flow rate and temperature, which was just as we expected based on the fact that the lower viscosity and decreased density would result in higher friction and churning losses. The last metric that was assessed was the enthalpy flow change, which increased with increasing mass flow rate and decreasing temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Energy, economic, and environmental analysis of integration of thermal energy storage into district heating systems using waste heat from data centres

Data centres produce waste heat, which can be utilized in district heating systems. However, the mismatch between data centres’ heat supply and district heating systems’ heat demands limits its utilization. Further, high peak loads increase the operation cost of district heating systems. This study aimed to solve these problems by introducing thermal energy storages. A water tank and a borehole thermal energy storage system were selected as the short-term and long-term thermal energy storage, respectively. Energy, economic, and environmental indicators were introduced to evaluate different solutions. The case study was a campus district heating system in Norway. Results showed that the water tank could shave the peak load by 31% and save the annual energy cost by 5%. The payback period was lower than 15 years when the storage efficiency remained higher than 80%. However, it had no obvious benefits in terms of mismatch relieving and CO emissions reduction. In contrast, the borehole thermal energy storage increased the waste heat utilization rate to 96% and reduced the annual CO emissions by 8%. However, the payback period was more than 17 years. These results provide guidelines for the retrofit of district heating systems, where data centres’ waste heat is available.

25 ENERGY STORAGE↗
DOE OSTI2024

UHT-CAMANCHE: Ultra-High Temperature Ceramic Additively Manufactured Compact Heat Exchangers

The conceptual basis for this project is the convergence of advanced ultra-high temperature ceramic materials and additive manufacturing technologies to produce compact ceramic heat exchangers with complex internal flow path geometries. Task areas were broadly divided into materials and manufacturing development, heat exchanger design, component testing, and techno-economic analysis. Technical challenges included the design and commissioning of new test facilities, improving feature resolution and deposition rate of ceramic additive manufacturing techniques, establishing process-structure-property relationships in additively manufactured ultra-high temperature ceramics, and assessing high temperature materials compatibility in CO 2 environments. The primary candidate material evaluated in this work is a composite comprising zirconium diboride (ZrB2) with 30 vol. % silicon carbide (SiC) which was selected based on its desirable combination of high temperature mechanical properties, high thermal and electrical conductivities, and oxidation resistance. High solids loaded ZrB2-SiC pastes suitable for extrusion-based additive manufacturing were developed for the first time as part of this work. Materials compatibility studies indicate this material oxidizes in CO 2 to form a protective borosilicate scale which transforms to pure silica above 1000°C. Parts made by additive manufacturing displayed enlarged grain sizes produced by pressureless sintering as compared to hot-press sintering. Increases in microstructural coarseness have outsized effect on oxidation performance up to 1400°C due to incomplete oxidation of coarse large diameter SiC particles resulting in lower amounts of silica that apparently inhibit protective scale formation. Additive manufacturing as a forming technique did not appear to significantly affect thermal conductivity, hardness, or elastic modulus, though flexural strength was reduced by half or more as compared to traditionally hot-pressed materials. This effect was attributed to the presence of strength-limiting flaws (ca. 40 microns in size) originating from extrudate inhomogeneities that could potentially be eliminated with further process improvements. Attempts to attain economies of scale for production of multi-kilowatt scale heat exchangers by ceramic additive manufacturing proved difficult. Lack of automation and a modest extrusion rate while retaining fine feature resolution made the overall process labor intensive and limited experimental throughput. A number of full-scale components were taken through post-process heat treatments including drying, binder burnout, and sintering; however, none survived without significant flaws or cracks. Therefore, no operational data from a newly installed heat exchanger test loop were able to be obtained during the performance period. Continued research and development is recommended to improve economic feasibility of ceramic additive manufacturing by standardizing the use of advanced sensors, artificial intelligence, and automation tools to reduce associated labor costs and accelerate production rates. The materials and manufacturing techniques demonstrated in this work are likely to find applications in defense and energy applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Behavior of an air-cooled thermosiphon during a non-air gas ingress event

Here, this study investigates the transient response of an air-cooled thermosiphon subjected to a sudden non-air gas ingress event. Results presented are from experimental testing conducted on a large-scale thermal hydraulic facility that examines heat removal performance of the Reactor Cavity Cooling System (RCCS) concept, a passive safety system for advanced nuclear reactors. Relying on buoyancy driven natural circulation flow, these systems feature a series of riser standpipes and coupled chimney network that provide a pathway for heat rejection to the atmosphere. In this work, the facility was modified to allow a transition of the draft intake from normal ambient air, to draft intake from an open-top volume containing high purity argon. Testing began by establishing normal operation and allowing the facility to reach steady-state thermal hydraulic flow conditions with natural air draft. The transitioned sequence was then initiated which simultaneously changed the inlet boundary from open air to a pathway from the quiescent argon volume. This event caused 1,200 cu-feet of the heavy gas, twice the internal volume of total facility flow path, to be drawn into the inlet plenum and ingress into the heated riser standpipes. With the upper chimney network still containing residual air, there was insufficient density difference to maintain buoyancy driven natural circulation. After a period of only 90 s past the ingress event, the facility experienced complete flow stagnation before entering an extended period of severely degraded system flow. Due to the cessation of bulk fluid movement and subsequent failure of its heat removal function, fluid and structural temperatures began to rise sharply. Re-circulation patterns developed within the multiple parallel riser standpipes, where hot gas near the outlets was observed to travel downward and re-enter the inlet of adjacent channels. After approximately 18-minutes, fluid temperatures and their associated density difference rose to a level sufficient to allow reestablishment of buoyancy driven system flow, and ultimately, recovery of facility operation to normal behavior.

42 ENGINEERING↗
DOE OSTI2021

Pyroelectric Heat Detection for Calibrated Measurement of Atomic Layer Deposition Reaction Heat

Atomic layer deposition (ALD) precursors and processes have been identified that enable the deposition of materials that span the periodic table. However, the detailed mechanisms, kinetics, thermodynamics, and complexities of even the most well-studied ALD half-reactions remain insufficiently resolved experimentally to test present computational hypotheses. In this work, a pyroelectric calorimeter is designed, implemented, calibrated, and electrically modeled to enable quantitative ALD reaction heat detection. The operation and response of three ALD calorimeter designs were evaluated for use as absolute ALD half-reaction heat detectors. The most effective design was calibrated in situ before being utilized to measure the heat generated by the reaction of trimethylaluminum with a hydroxylated alumina surface to produce 96 μJ/cm 2 over a reaction time of ~30 ms. With thermal and temporal resolutions down to 0.1 μJ/cm 2 and 50 ns, respectively, this sensitive and ultrafast probe is poised to improve our fundamental understanding of numerous ALD reaction mechanisms through quantitative comparison with first-principles computation predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Global Heat Uptake by Inland Waters

Heat uptake is a key variable for understanding the Earth system response to greenhouse gas forcing. Despite the importance of this heat budget, heat uptake by inland waters has so far not been quantified. Here we use a unique combination of global-scale lake models, global hydrological models and Earth system models to quantify global heat uptake by natural lakes, reservoirs and rivers. The total net heat uptake by inland waters amounts to 2.6+/-3.2x10 20 J over the period 1900-2020, corresponding to 3.6% of the energy stored on land. The overall uptake is dominated by natural lakes (111.7%), followed by reservoir warming (2.3%). Rivers contribute negatively (-14%) due to a decreasing water volume. The thermal energy of water trapped on land due to reservoir construction exceeds inland water heat uptake by a factor ~10.4. This first quantification underlines that the heat uptake by inland waters is small, but not negligible.

58 GEOSCIENCES↗
DOE OSTI2024

Thermophysical Property Measurements of HTM and CM (Final Technical Report)

The goal of this project is to gather thermophysical property data – specifically, thermal conductivity, thermal diffusivity, and specific heat – of heat transfer media (HTMs) and containment materials (CMs) used in Topic Area 1 and 2A at high temperatures (>700°C). This goal was met by completing objectives such as qualifying high temperature measurement techniques, defining allowable uncertainty metrics, reporting properties in a public database, and providing ongoing support for prioritized materials. These are described in detail across three budget periods

36 MATERIALS SCIENCE↗
DOE OSTI2022

Wettability and CHF limits of Accident-Tolerant nuclear fuel cladding materials in light water reactor conditions

Here, we present the results of experimental investigations aimed at evaluating the thermal–hydraulic performance of chromium-coated zircaloy, i.e., one of the most promising accident tolerant fuel (ATF) cladding material for light water nuclear reactors. Precisely, we investigate the wettability and critical heat flux (CHF) limits of chromium-coated and conventional zircaloy surfaces in prototypical reactor conditions. For both surface types, we measure the contact angle in a vapor-saturated atmosphere from ambient pressure to the operating pressure of pressurized water reactors (PWRs), i.e., ~15 MPa. We measure the ambient-pressure steady-state flow boiling CHF with a spatially uniform heat flux. We measure the high-pressure steady-state flow boiling CHF with a cosine shape heat flux (up to 20 MPa) and with a uniform heat flux (up to 15 MPa), also exploring the effect of CRUD deposits on the chromium-coated surface. Our results reveal that the chromium surface and the bare zircaloy surface have similar wettability and both become super-hydrophilic in PWR conditions, and that there is practically no difference in the steady-state CHF limits, both at low-pressure and high-pressure conditions, also when the chromium-coated surface is covered by a CRUD deposit. However, while the chromium-coating does not improve the CHF compared to the bare zircaloy surface, it improves the post-CHF behavior. The chromium coating prevents the reaction between zircaloy and steam, which results in the formation of a brittle zirconium oxide through the surface of the cladding. We also measure the transient CHF under exponentially escalating heat flux inputs of a nano-smooth and a rough surface mimicking a chromium-coated zircaloy cladding. Interestingly, the results of the transient heat flux tests suggest that the CHF limit for very short periods (i.e., fast transients) is independent of the surface finish, being the same for a rough chromium surface or a nano-smooth surface.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Phase evolution and amorphous stability upon solid-state reaction in superlattice like Ge–Sb–Te combinatorial thin-film

In this paper, the superlattice-like (SLL) Ge–Sb–Te combinatorial thin films were prepared by using a high-throughput ion beam sputtering system. The phase evolution and amorphous stability of such films undergoing heat treatment as a function of the coating sequence and modulation period were systematically studied. The composition structure diagram was constructed via an automated process of data obtained by high-throughput synchrotron micro-X-ray diffraction and lab-based micro-X-ray fluorescence. Furthermore, the element distribution and microstructure in the depth direction of the SLL thin films were characterized with time-of-flight secondary ion mass spectrometry and transmission electron microscopy, respectively. These studies demonstrated that the coating sequence has a significant effect on the element distribution in the as-deposited SLL thin films and the structure of the final product upon solid-state reaction. Reducing the modulation period of the SLL thin film improves the stability of the amorphous Ge–Sb–Te phase. This work lays a solid foundation for the rational design of SLL Ge–Sb–Te thin films to improve their performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

TESS giants transiting giants V – two hot Jupiters orbiting red giant hosts

ABSTRACT In this work, we present the discovery and confirmation of two hot Jupiters orbiting red giant stars, TOI-4377 b and TOI-4551 b, observed by Transiting Exoplanet Survey Satellite in the Southern ecliptic hemisphere and later followed-up with radial-velocity (RV) observations. For TOI-4377 b, we report a mass of $0.957^{+0.089}_{-0.087} \ M_\mathrm{J}$ and a inflated radius of 1.348 ± 0.081 RJ orbiting an evolved intermediate-mass star (1.36 M⊙ and 3.52 R⊙; TIC 394918211) on a period of of 4.378 d. For TOI-4551 b, we report a mass of 1.49 ± 0.13 MJ and a radius that is not obviously inflated of $1.058^{+0.110}_{-0.062} \ R_\mathrm{J}$, also orbiting an evolved intermediate-mass star (1.31 M⊙ and 3.55 R⊙; TIC 204650483) on a period of 9.956 d. We place both planets in context of known systems with hot Jupiters orbiting evolved hosts, and note that both planets follow the observed trend of the known stellar incident flux-planetary radius relation observed for these short-period giants. Additionally, we produce planetary interior models to estimate the heating efficiency with which stellar incident flux is deposited in the planet’s interior, estimating values of $1.91 \pm 0.48~{{\ \rm per\ cent}}$ and $2.19 \pm 0.45~{{\ \rm per\ cent}}$ for TOI-4377 b and TOI-4551 b, respectively. These values are in line with the known population of hot Jupiters, including hot Jupiters orbiting main-sequence hosts, which suggests that the radii of our planets have re-inflated in step with their parent star’s brightening as they evolved into the post-main sequence. Finally, we evaluate the potential to observe orbital decay in both systems.

Pereira, Filipe (ORCID:0000000221577146)↗
DOE OSTI2021

Multi-stage falling particle receivers

The present disclosure is directed to multi-stage falling particle receivers and methods of falling particle heating. As the particles fall through the receiver, the particles are periodically collected and released by flow retarding devices. The periodic catch-and-release of the particles falling through the receiver reduces particle flow dispersion, increases particle opacity and solar absorption, and reduces erosion and damage to surfaces caused by direct particle impingement.

Ho, Clifford K.↗
DOE OSTI2023

Multi-stage falling particle receivers

The present disclosure is directed to multi-stage falling particle receivers and methods of falling particle heating. As the particles fall through the receiver, the particles are periodically collected and released by flow retarding devices. The periodic catch-and-release of the particles falling through the receiver reduces particle flow dispersion, increases particle opacity and solar absorption, and reduces erosion and damage to surfaces caused by direct particle impingement.

Ho, Clifford K.↗
DOE OSTI2022

OECD/NEA MPCMIV Benchmark - Preliminary fuel performance results

The on-going OECD/NEA Multi-physics Pellet Cladding Mechanical Interaction Validation (MPCMIV) benchmark aims to provide guidance on multi-physics validation through the modelling of two cold ramps. In this paper, the first results for the base irradiation of the father rod and fuel rodlet (refabricated from the father rod), and the first cold ramp are presented. The base irradiation consists of 3 years of irradiation in the Forsmark-2 reactor. The cold ramp encompasses a steady-state pre-ramp period of less than one hour at a low constant linear heat rate (LHR) followed by a ramp test (< 1 min) with a much higher maximal LHR. The base irradiation is modelled using the fuel performance codes FRAPCON and FAST, while the cold ramp modeling is using the fuel performance code FRAPTRAN. Several missing parameters for FRAPCON/FAST base irradiation models have been selected using multiple references such as the OECD/NEA light water reactor Uncertainty Analysis in Modelling (UAM) benchmark specifications and the FRAPCON Integral Assessment report. The obtained results for the base irradiation such as the cladding outer diameter show reasonable agreement with the experimental measurements. The results for the cold ramp show larger differences with the experimental measurements (e.g., cladding axial elongation). However, such differences have been observed as well in other studies involving pellet cladding mechanical interaction analyses and are attributed to the fuel performance modelling assumptions and to the tuned modelling parameters that were not covered by the specifications. Uncertainty and sensitivity analysis might allow a better quantification of these missing parameters. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Periodically and quasi-periodically driven dynamics of Bose-Einstein condensates

We study the quantum dynamics of Bose-Einstein condensates when the scattering length is modulated periodically or quasi-periodically in time within the Bogoliubov framework. For the periodically driven case, we consider two protocols where the modulation is a square-wave or a sine-wave. In both protocols for each fixed momentum, there are heating and non-heating phases, and a phase boundary between them. The two phases are distinguished by whether the number of excited particles grows exponentially or not. For the quasi-periodically driven case, we again consider two protocols: the square-wave quasi-periodicity, where the excitations are generated for almost all parameters as an analog of the Fibonacci-type quasi-crystal; and the sine-wave quasi-periodicity, where there is a finite measure parameter regime for the non-heating phase. We also plot the analogs of the Hofstadter butterfly for both protocols.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

End-Use Savings Shapes Measure Documentation: Thermostat Control for Load Shedding in Large Offices

This documentation focuses on a single End-Use Savings Shape measure - thermostat control for load shedding. The thermostat control for load shedding measure applies heating and cooling temperature setpoint offsets for reducing the heating and cooling load during peak window. The measure takes daily peak load schedule inputs generated by the method "Dispatch Schedule Generation" described in the "Supplemental Documentation: Dispatch Schedule Generation for Demand Flexibility Measures" to determine the start and end times of the peak window, and then adjusts the thermostat cooling and/or heating setpoints by an offset value from original schedules during the peak window to reduce the HVAC or whole building daily peak load. The measure is flexible and allows users to adjust the heating and cooling offset values respectively, but for this study, the adjustment for heating and cooling setpoints are set to -2 degrees Celsius and +2 degrees Celsius by default. The measure provides options of adding rebound control period (default 2 hours) after peak windows for the setpoints to be ramped back to default values, to prevent the system from generating higher peak demand with step changes of setpoints in post-peak periods . This measure is applicable t o large offices equipped with electric HVAC system (either electric cooling only or both electric heating and cooling), which account for approximately 8.72% of the ComStock floor area. The thermostat control for load shedding measure demonstrates 2-5% daily peak demand reduction and 0.068% total site energy savings (3 trillion British thermal units [TBtu]) for the U.S. commercial building stock modeled in ComStock.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗