Search NASA⌕ Search

SEARCH · Search NASA

Results for “Photocurrent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Large Area Near‐Field Thermophotovoltaics for Low Temperature Applications

Abstract Thermophotovoltaics, devices that convert thermal infrared photons to electricity, offer a key pathway for a variety of critical renewable energy technologies including thermal energy storage, waste heat recovery, and direct solar‐thermal power generation. However, conventional far‐field devices struggle to generate reasonable powers at lower temperatures. Near‐field thermophotovoltaics provide a pathway to substantially higher powers by leveraging photon tunneling effects. Here a large area near‐field thermophotovoltaic device is presented, created with an epitaxial co‐fabrication approach, that consists of a self‐supported 0.28 cm 2 emitter‐cell pair with a 150 nm gap. The device generates 1.22 mW at 460 °C, a 25‐fold increase over the same cell measured in a far‐field configuration. Furthermore, the near‐field device demonstrates short circuit current densities greater than the far‐field photocurrent limit at all the temperatures tested, confirming the role of photon tunneling effects in the performance enhancement. Modeling suggests several practical directions for cell improvements and further increases in power density. These results highlight the promise of near‐field thermophotovoltaics, especially for low temperature applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Study of Photocarriers Lifetime Distribution in a-Si:H via Magneto-photoconductivity and Magneto-Photoluminescence

In this report the magneto-photoluminescence (MPL) of localized photocarriers and magneto-photoconductivity (MPC) of delocalized photocarriers in amorphous hydrogenated silicon (a-Si:H) films and devices, respectively, are investigated. Both responses are caused by mixing of spin sublevels in the photogenerated electron–hole (e–h) pairs that alters their recombination and dissociation rates. The spin mixing occurs by a combination of hyperfine interaction (HFI) between spin ½ photocarriers and neighboring 29 Si and 1 H nuclei, and the Δg mechanism which originates from a difference in the Landé g-factors of electrons and holes. The existing disorder in a-Si:H films leads to dispersive field response that is described by a unique dispersive parameter α < 1, from which the e–h lifetime distribution, g(τ) is obtained. The mean e–h lifetime is found to be ≈12 ns for the high-energy, relatively delocalized photocarriers generating the photocurrent, as compared to ≈200 ps for the lower energy, trapped e–h pairs which yield photoluminescence. The MPL(B) and MPC(B) responses in a-Si:H subjected to prolonged illumination that causes Staebler–Wronski type degradation, and subsequent annealing are studied. The illumination-induced photocarrier localization that enhances the HFI component is found, which dramatically decreases upon annealing; this method can assess optoelectronic device degradation.

Staebler-Wronski effect↗
DOE OSTI2023

Perovskite CsPbBr 3 Single-Crystal Detector Operating at 10 10 Photons s -1 mm -2 for Ultra-High Flux X-ray Detection

Semiconductors for detecting hard radiation are confronted with considerable problems when operating at high photon fluxes. A perovskite CsPbBr 3 single-crystal detector capable of operating at X-ray fluxes of up to 10 10 photons s -1 mm -2 with beam area ≤ 0.25 mm 2 at 58.61 keV for current-mode X-ray detection is reported. The spectrometer-grade melt-grown CsPbBr 3 detectors show a gamma-ray energy resolution of ~7.5% at 122 keV for 57 Co and dark current as low as 4.3 nA (0.5 nA mm -2 ) at a reverse bias voltage of 200 V (118 V mm -1 ). The detector is tested at X-ray energies of 8.2, 10, and 58.61 keV at a synchrotron light source under a reverse bias voltage of up to 1000 V (588 V mm -1 ). Under a sufficiently high bias voltage and within several hundreds of seconds X-ray exposure, good photocurrent linearity (goodness of fit R 2 > 0.99) and reproducibility are obtained up to a flux of ≈10 10 photons s -1 mm -2 at beam area 0.25 mm 2 with Lower Limit of Detection of ≈10 5 photons s -1 mm -2 and Charge Collection Efficiency of ≈100% for 58.61 keV X-rays. Therefore, wide application of CsPbBr 3 detectors in high-flux X-ray detection is anticipated.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Synergy of Liquid-Crystalline Small-Molecule and Polymeric Donors Delivers Uncommon Morphology Evolution and 16.6% Efficiency Organic Photovoltaics

Achieving an ideal morphology is an imperative avenue for enhancing key parameters toward high-performing organic solar cells (OSCs). Among a myriad of morphological-control methods, the strategy of incorporating a third component with structural similarity and crystallinity difference to construct ternary OSCs has emerged as an effective approach to regulate morphology. A nematic liquid-crystalline benzodithiophene terthiophene rhodamine (BTR) molecule, which possesses the same alkylthio-thienyl-substituted benzo moiety but obviously stronger crystallinity compared to classical medium-bandgap polymeric donor PM6, is employed as a third component to construct ternary OSCs based on a PM6:BTR:Y6 system. The doping of BTR (5 wt%) is found to be enough to improve the OSC morphology—significantly enhancing the crystallinity of the photoactive layer while slightly reducing the donor/acceptor phase separation scale simultaneously. Rarely is such a morphology evolution reported. It positively affects the electronic properties of the device—prolongs the carrier lifetime, shortens the photocurrent decay time, facilitates exciton dissociation, charge transport, and collection, and ultimately boosts the power conversion efficiency from 15.7% to 16.6%. This result demonstrates that the successful synergy of liquid-crystalline small-molecule and polymeric donors delicately adjusts the active-layer morphology and refines device performance, which brings vibrancy to the OSC research field.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Modulating Charge Transfer Efficiency of Hematite Photoanode with Hybrid Dual‐Metal–Organic Frameworks for Boosting Photoelectrochemical Water Oxidation

Abstract The glorious charge transfer efficiency of photoanode is an important factor for efficient photoelectrochemical (PEC) water oxidation. However, it is often limited by slow kinetics of oxygen evolution reaction. Herein, a dual transition metal‐based metal–organic frameworks (MOF) cocatalyst, Fe@Ni–MOF, is introduced into a titanium‐doped hematite (Fe 2 O 3 :Ti) photoanode. The combination of Ni and Fe can optimize the filling of 3d orbitals. Moreover, the introduction of Fe donates electrons to Ni in the MOF structure, thus, suppressing the irreversible (long‐life‐time) oxidation of Ni 2+ into Ni 3+ . The resulting Fe@Ni–MOF/Fe 2 O 3 :Ti photoanode exhibits ∼threefold enhancement in the photocurrent density at 1.23 V versus the reversible hydrogen electrode. Kinetic analysis of the PEC water oxidation processes indicates that this performance improvement is primarily due to modulating the charge transfer efficiency of hematite photoanode. Further results show that a single transition metal‐based MOF cocatalyst, Ni–MOF, exhibits slow charge transfer in spite of a reduction in surface charge recombination, resulting in a smaller charge transfer efficiency. These findings provide new insights for the development of photoelectrodes decorated with MOFs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Organometal Halide Perovskite‐Based Photoelectrochemical Module Systems for Scalable Unassisted Solar Water Splitting

Despite achievements in the remarkable photoelectrochemical (PEC) performance of photoelectrodes based on organometal halide perovskites (OHPs), the scaling up of small-scale OHP-based PEC systems to large-scale systems remains a great challenge for their practical application in solar water splitting. Significant resistive losses and intrinsic defects are major obstacles to the scaling up of OHP-based PEC systems, leading to the PEC performance degradation of large-scale OHP photoelectrodes. Herein, a scalable design of the OHP-based PEC systems by modularization of the optimized OHP photoelectrodes exhibiting a high solar-to-hydrogen conversion efficiency of 10.4% is suggested. As a proof-of-concept, the OHP-based PEC module achieves an optimal PEC performance by avoiding major obstacles in the scaling up of the OHP photoelectrodes. The constructed OHP module is composed of a total of 16 OHP photoelectrodes, and a photocurrent of 11.52 mA is achieved under natural sunlight without external bias. The successful operation of unassisted solar water splitting using the OHP module without external bias can provide insights into the design of scalable OHP-based PEC systems for future practical application and commercialization.

14 SOLAR ENERGY↗
DOE OSTI2024

Investigation of Sub‐Bandgap Emission and Unexpected n‐Type Behavior in Undoped Polycrystalline CdSe x Te 1‐x

Abstract Se alloying has enabled significantly higher carrier lifetimes and photocurrents in CdTe solar cells, but these benefits can be highly dependent on CdSe x Te 1‐x processing. This work evaluates the optoelectronic, chemical, and electronic properties of thick (3 µm) undoped CdSe x Te 1‐x of uniform composition and varied processing conditions (CdSe x Te 1‐x evaporation rate, CdCl 2 anneal, Se content) chosen to reflect various standard device processing conditions. Sub‐bandgap defect emission is observed, which increased as Se content increased and with “GrV‐optimized CdCl 2 ” (i.e., CdCl 2 anneal conditions used for group‐V‐doped devices). Low carrier lifetime is found for GrV‐optimized CdCl 2 , slow CdSe x Te 1‐x deposition, and low‐Se films. Interestingly, all films (including CdTe control) exhibited n‐type behavior, where electron density increased with Se up to an estimated ≈10 17 cm −3 . This behavior appears to originate during the CdCl 2 anneal, possibly from Se diffusion leading to anion vacancy (e.g., V Se , V Te ) and Cl Te generation.

14 SOLAR ENERGY↗
DOE OSTI2025

Order–Disorder Phase Stabilization by Pressure‐Induced Charge Transfer Enhances the Ferroelectric Photovoltaic Effect in Multiferroic BaFe 4 O 7

Abstract Multiferroic ferroelectric photovoltaic (FPV) materials, combining magnetic and ferroelectric properties, are of paramount importance for optoelectronic and photovoltaic applications. However, optimizing both the remanent polarization and the optical bandgap—key factors for enhanced FPV performance—presents a significant challenge due to their trade‐off. This work shows that pressure‐induced charge transfer between different metal sites can break this trade‐off. Above ≈20 GPa, charge transfer between different trivalent iron (Fe) sites in the multiferroic material BaFe 4 O 7 leads to Fe valence disproportionation, FeO 4 tetrahedra disorder, and Jahn–Teller distortion of FeO 6 octahedra. These changes reduce the bandgap, lower resistivity, and enhance ferroelectric polarization, resulting in a 2.5‐fold increase in photocurrent. Upon decompression, BaFe 4 O 7 retains an order–disorder structure, optimal ferroelectric and optical properties at ambient conditions. This work provides a novel pathway to simultaneously optimizing ferroelectricity and bandgap via pressure‐induced charge transfer, overcoming the traditional trade‐off in FPV materials, and offers a promising approach for developing high polarization performance, narrow‐bandgap FPV materials.

Chemistry↗
DOE OSTI2020

Emergent Degradation Phenomena Demonstrated on Resilient, Flexible, and Scalable Integrated Photoelectrochemical Cells

Photoelectrochemical (PEC) water splitting provides a pathway to generate sustainable clean fuels using the two most abundant resources on Earth: sunlight and water. Currently, most of the successful models of PEC cells are still fabricated on small scales near 1 cm 2 , which largely limits the mass deployment of solar-fuel production. Here, the scale-up to 8 cm 2 of an integrated PEC (IPEC) device is demonstrated and its performance compared to a 1 cm 2 IPEC cell, using state-of-the-art iridium and platinum catalysts with III–V photoabsorbers. The initial photocurrents at 1 sun are 8 and 7 mA cm -2 with degradation rates of 0.60 and 0.47 mA cm -2 day -1 , during unbiased operation for the 1 and 8 cm 2 devices, respectively. Additionally, evaluating under outdoor and indoor conditions at two U.S. National Laboratories reveals similar results, evidencing the reproducibility of this design's performance. Furthermore, the emerging degradation mechanisms during scale-up are investigated and the knowledge gained from this work will provide feedback to the broader community, since PEC device durability is a limiting factor in its potential future deployment.

25 ENERGY STORAGE↗
DOE OSTI2020

Water Splitting: Emergent Degradation Phenomena Demonstrated on Resilient, Flexible, and Scalable Integrated Photoelectrochemical Cells (Adv. Energy Mater. 48/2020)

We report Photoelectrochemical (PEC) water splitting provides a pathway to generate sustainable clean fuels using the two most abundant resources on Earth: sunlight and water. Currently, most of the successful models of PEC cells are still fabricated on small scales near 1 cm 2 , which largely limits the mass deployment of solar-fuel production. Here, the scale-up to 8 cm 2 of an integrated PEC (IPEC) device is demonstrated and its performance compared to a 1 cm 2 IPEC cell, using state-of-the-art iridium and platinum catalysts with III-V photoabsorbers. The initial photocurrents at 1 sun were 8 and 7 mA cm -2 with degradation rates of 0.60 and 0.47 mA cm -2 day -1 , during unbiased operation for the 1 and 8 cm 2 devices, respectively. Evaluating under outdoor and indoor conditions at two US National Laboratories revealed similar results, evidencing the reproducibility of this design’s performance. Furthermore, the emerging degradation mechanisms during scale-up are investigated and the knowledge gained from this work will provide feedback to the broader community, since PEC device durability is a limiting factor in its potential future deployment.

25 ENERGY STORAGE↗
DOE OSTI2023

Linking Phase Behavior to Performance Parameters in Non-Fullerene Acceptor Solar Cells

Performance of nonfullerene-based organic solar cells is largely dependent on the donor:acceptor blend morphology, which is initially tuned by composition. However, morphological design rules are difficult to identify due to the complex relationship between composition-dependent phase behavior and performance properties. In this study, the authors are able to establish a direct link between PM6:Y6 film morphology and device properties by combining grazing-incidence wide-angle X-ray scattering with highly sensitive Fourier transform photocurrent spectroscopy. By analyzing properties across the full composition range, interfacial microstructure and the corresponding charge transfer (CT) states are identified and direct structure–property relationships are established. Here the results indicate that open-circuit voltage is controlled by the CT state at amorphous-PM6:crystalline-Y6 interfaces. Crystalline Y6 is found to increase both transport and non-radiative recombination, suggesting that morphological tradeoffs may be necessary for overall device optimization.

14 SOLAR ENERGY↗
DOE OSTI2024

Effective Corrosion-Resistant Single-Atom Alloy Catalyst on HfO 2 -Passivated BiVO 4 Photoanode for Durable (≈800 h) Solar Water Oxidation

Green hydrogen (H 2 ) production from solar water splitting necessitates photoelectrodes with superior photoelectrochemical (PEC) activity and durability. However, surface defects and photocorrosion instability—especially at high potentials—limit PEC performance and stability. Herein, the prototypical bismuth vanadate (BiVO 4 ) photoanode is used to demonstrate a holistic approach to improve photocurrent density and long-term stability. In this approach, high surface-area nanostructuring of BiVO 4 is combined with barium (Ba) doping with semi-crystalline hafnium oxide (HfO 2 ) surface passivation and single-atom nickel platinum (NiPt) catalysts. The introduction of Ba 2+ ions into BiVO 4 increases the concentration of conductive V 4+ ions or the ratio of V 4+ ions to oxygen vacancies, avoiding V 5+ dissolution during water oxidation. The semi-crystalline HfO 2 , which serves as a passivation layer, prevents BiVO 4 photocorrosion by suppressing harmful chemical reactions when holes are transferred to the electrolyte. The synergistic use of isolated single-atom and Ni-Pt coordination improves charge transfer at the photoanode/electrolyte interface, leading to enhanced PEC kinetics and stability. As a result, a photoelectrode is demonstrated with ≈6.5 mA cm -2 at 1.23 V versus a reversible hydrogen electrode (RHE) and continuous operation for 800 h with a negligible degradation rate. This work provides a promising approach to improve photoanodes for PEC H 2 production.

08 HYDROGEN↗
DOE OSTI2020

Energetic Tug-of-War between Pt and Leaky TiO 2 : Positive and Negative Effects on the Function of Molecularly-Modified p -Si(111)|TiO 2 |Pt Photocathodes

Photoelectrochemical solar energy conversion to chemical products is a promising avenue towards renewable fuels, and TiO 2 deposition on semiconductor photocathodes is a widespread surface protection strategy. However, the electronic, thermodynamic, and kinetic effects of protection layers on interfacial energetics remains poorly understood. Here, electrochemical data (photocurrent onset and flatband potentials) of p-Si(111)|TiO 2 |Pt is collected in contact with an outer-sphere redox couple. We find that onset potentials shift negatively as a function of increasing oxide thickness, but this effect is not reflected in the flatband potentials. This reveals the mechanism of these shifts is kinetic rather than thermodynamic,and suggests that hole leakage through the TiO 2 is responsible. When Pt nanoparticles are deposited onto the TiO 2 , positive shifts in both the onset and flatband potentials are observed, revealing Pt catalysts are beneficial for more than just increased catalytic rates. These results highlight the importance of understanding the effects of surface modifications on the energetics at the interface in both catalytic and simple electron transfer systems.

14 SOLAR ENERGY↗
DOE OSTI2026

Controlling Nb(IV) Defects in SrNbO 2 N Oxygen Evolution Photocatalyst by Ammonolysis With Dinitrogen–Ammonia Mixtures

Strontium niobium oxynitride (SrNbO 2 N) is a promising, corrosion resistant semiconductor for the visible light-driven water splitting reaction, a non-photovoltaic pathway to green hydrogen fuel. However, SrNbO 2 N materials made by ammonolysis usually contain Nb 4+ defect states that cause electron–hole recombination. Here, in this work, we demonstrate that such defects can be minimized by synthesizing SrNbO 2 N from metal oxides in a mixed 13%:87% (vol) NH 3 /N 2 atmosphere. According to electron paramagnetic resonance (EPR), SrNbO 2 N made in pure NH 3 contains paramagnetic impurities with g = 2.002 and 2.195, which can be assigned to lattice and surface Nb 4+ defects. These states also cause broad optical absorptions centered at 800 and 1020 nm, respectively, and the lattice defect produces a 1.55–1.63 eV signal in surface photovoltage spectra. The improved SrNbO 2 N contains five times fewer lattice Nb 4+ defects (8.95 × 10 15 cm −3 ), based on the integrated EPR signal intensity, and supports a water oxidation photocurrent of 1.07 mA cm −2 at 1.23 V versus RHE under simulated sunlight and an apparent quantum efficiency of 5.1% at 400 nm during photocatalytic oxygen evolution. Based on earlier results with LaTiO 2 N and BaTaO 2 N, dilution of NH 3 during synthesis appears generally beneficial to transition metal oxynitrides.

electron paramagnetic resonance↗
DOE OSTI2026

Synergistic Alignment of Low Aspect‐Ratio π‐Conjugated Molecules Enables Exceptional UV–vis–NIR Polarization Detection

Abstract Polarization detection enhances signal contrast and is widely utilized in diverse advanced applications. An ongoing challenge is the development of high‐performance polarization‐sensitive photodetectors based on optically anisotropic organic semiconductors, particularly in the near‐infrared (NIR) region. While uniaxially aligned π‐conjugated polymers with high aspect ratios exhibit strong linear dichroism and have shown promise, their limited NIR performance and heavy reliance on polymer material now represent critical limitations. Here, a breakthrough is reported in achieving giant linear dichroism and exceptional polarization detection with low aspect‐ratios (AR) non‐fullerene small‐molecule (NFSM) acceptors, extending polarization sensitivity from the UV–vis to the NIR range. An impressive dichroic ratio of 27.1 at 605 nm and 12.0 at 780 nm is demonstrated. The maximum polarization photocurrent ratio is 11.2 at 780 nm under parallel versus perpendicular polarized light. This unprecedented performance originates from synergistic molecular alignment, wherein NFSMs significantly enhance the uniaxial orientation of both the polymer matrix and the NFSMs themselves during self‐assembly and thermal annealing. Besides, such a linear‐polarization‐sensitive photodetectors (LPS‐PDs) are showcased in generating degree‐of‐linear‐polarization imaging. The work establishes NFSMs as a viable material system for next‐generation of organic LPS‐PDs and provides fundamental insights into structural origins of polarization sensitivity in low AR organic semiconductors.

Xue, Yingying↗
DOE OSTI2021

Modeling of transport in carrier-selective contacts in silicon heterojunction solar cells

High-performance silicon heterojunction (SHJ) solar cells use carrier-selective contact structures based on hydrogentated amorphous Si (a-Si:H) to maximize collection of photogenerated carriers. The high open circuit voltages observed experimentally in SHJ cells require that the carrier-selective contacts provide selectivity and passivation. However, a microscopic understanding of the dynamics of carrier transport through the a-Si layer is currently lacking. In this paper, we explicitly simulate the transport of holes across the a-Si:H(i) layer using a novel kinetic Monte Carlo approach. The hole-selective contact structure investigated in this paper uses p-type doped a-Si:H(p) and intrinsic a-Si:H(i) on an n-type crystalline silicon wafer, where the selectivity is provided by the a-Si:H(p) and the passivation is provided by the a-Si:H(i). However, in addition to the passivation provided by the a-Si:H(i), this layer also creates a potential barrier to the collection of photogenerated holes. There have been experimental studies in the literature that have suggested that multi-phonon processes are the main transport mechanism that assists in the transport of holes across the intrinsic a-Si:H barrier. Simulations presented here show that multi-phonon injection of holes into the a-Si:H(i) layer is the rate limiting step for transport across the a-Si:H(i) layer. Our results indicate that multi-phonon transport is strongly dependent on the electric field at the a-Si:H(i)/c-Si heterointerface as well. Transport simulations presented in this paper are consistent with experimental findings that multi-phonon processes limit transport across the a-Si:H(i) layer and are responsible for photocurrent suppression at the a-Si:H(i)/c-Si heterointerface when these processes are slower than the associated incident hole flux due to photo-excitation.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Morphological–Electrical Property Relation in Cu(In,Ga)(S,Se) 2 Solar Cells: Significance of Crystal Grain Growth and Band Grading by Potassium Treatment

Abstract Solution‐processed Cu(In,Ga)(S,Se) 2 (CIGS) has a great potential for the production of large‐area photovoltaic devices at low cost. However, CIGS solar cells processed from solution exhibit relatively lower performance compared to vacuum‐processed devices because of a lack of proper composition distribution, which is mainly instigated by the limited Se uptake during chalcogenization. In this work, a unique potassium treatment method is utilized to improve the selenium uptake judiciously, enhancing grain sizes and forming a wider bandgap minimum region. Careful engineering of the bandgap grading structure also results in an enlarged space charge region, which is favorable for electron–hole separation and efficient charge carrier collection. Besides, this device processing approach has led to a linearly increasing electron diffusion length and carrier lifetime with increasing the grain size of the CIGS film, which is a critical achievement for enhancing photocurrent yield. Overall, 15% of power conversion efficiency is achieved in solar cells processed from environmentally benign solutions. This approach offers critical insights for precise device design and processing rules for solution‐processed CIGS solar cells.

Kim, Joo‐Hyun↗
DOE OSTI2022

High Sensitivity of Non–Fullerene Organic Solar Cells Morphology and Performance to a Processing Additive

Although solvent additives are used to optimize device performance in many novel non-fullerene acceptor (NFA) organic solar cells (OSCs), the effect of processing additives on OSC structures and functionalities can be difficult to predict. Here, two polymer-NFA OSCs with highly sensitive device performance and morphology to the most prevalent solvent additive chloronaphthalene (CN) are presented. Devices with 1% CN additive are found to nearly double device efficiencies to 10%. However, additive concentrations even slightly above optimum significantly hinder device performance due to formation of undesirable morphologies. A comprehensive analysis of device nanostructure shows that CN is critical to increasing crystallinity and optimizing phase separation up to the optimal concentration for suppressing charge recombination and maximizing performance. Here, domain purity and crystallinity are highly correlated with photocurrent and fill factors. However, this effect is in competition with uncontrolled crystallization of NFAs that occur at CN concentrations slightly above optimal. This study highlights how slight variations of solvent additives can impart detrimental effects to morphology and device performance of NFA OSCs. Furthermore, successful scale-up processing of NFA-based OSCs will require extreme formulation control, a tuned NFA structure that resists runaway crystallization, or alternative methods such as additive-free fabrication.

14 SOLAR ENERGY↗