Results for “Plume Surface Interactions” — Page 11

NASA NTRS2012

Jupiter and Its Galilean Satellites

Jupiter is one of the two most studied planets other than Earth in our Solar System. It is the largest, fastest rotating, has the strongest magnetic field, and an incredibly diverse set of satellites, most prominent of which are the four Galilean satellites discovered in 1610. Io, Europa, Ganymede and Callisto encompass some of the most bizarre environments known in the solar system, from Io, the most volcanically active and perhaps the most inhospitable body known, to Europa, currently thought to be the most likely extraterrestrial abode for habitability, to Ganymede, which is larger than Mercury, and Callisto, which has the oldest surface known in the solar system with the widest array of crater morphologies known. One of the premier areas of scientific return in solar system research in the past 15 years, due in large part to the Galileo mission and observations by the Hubble Space Telescope, has been a remarkable increase in our knowledge about these satellites. Discoveries have been made of tenuous molecular oxygen atmospheres on Europa and Ganymede, a magnetic field and accompanying auroral emissions at the poles of Ganymede, and of ozone and sulfur dioxide embedded in the surfaces of Europa, Ganymede and Callisto. Io's unusual sulfur dioxide atmosphere, including its volcanic plumes and strong electrodynamic interaction with magnetospheric plasma, has finally been quantitatively characterized. This talk will present highlights from the recent discoveries and advances in our understanding of these fascinating objects.

McGrath, Melissa A.↗

NASA NTRS1983

Space Shuttle third flight /STS-3/ entry RCS analysis

Flight data obtained from three Space Transportation System orbiter entries (STS-1, 2, and 3) are processed and analyzed to determine the roll interactions caused by the firing of the entry reaction control system (RCS). Comparisons between the flight-derived parameters and the predicted derivatives without interaction effects are made. The flight-derived RCS Plume flow-field interaction effects are independently deduced by direct integration of the incremental changes in the wing upper surface pressures induced by RCS side thruster firings. The separately obtained interaction effects are compared to the predicted values and the differences are discussed.

Scallion, W. I.↗

NASA NTRS1994

Numerical simulation of helicopter engine plume in forward flight

Flowfields around helicopters contain complex flow features such as large separated flow regions, vortices, shear layers, blown and suction surfaces and an inherently unsteady flow imposed by the rotor system. Another complicated feature of helicopters is their infrared signature. Typically, the aircraft's exhaust plume interacts with the rotor downwash, the fuselage's complicated flowfield, and the fuselage itself giving each aircraft a unique IR signature at given flight conditions. The goal of this project was to compute the flow about a realistic helicopter fuselage including the interaction of the engine air intakes and exhaust plume. The computations solve the Think-Layer Navier Stokes equations using overset type grids and in particular use the OVERFLOW code by Buning of NASA Ames. During this three month effort, an existing grid system of the Comanche Helicopter was to be modified to include the engine inlet and the hot engine exhaust. The engine exhaust was to be modeled as hot air exhaust. However, considerable changes in the fuselage geometry required a complete regriding of the surface and volume grids. The engine plume computations have been delayed to future efforts. The results of the current work consists of a complete regeneration of the surface and volume grids of the most recent Comanche fuselage along with a flowfield computation.

Dimanlig, Arsenio C. B.↗

NASA NTRS2010

Radiation Environment and Surface Radiolytic Interactions at Mimas

Saturn's innermost principal moon Mimas shares the distinction with Europa at Jupiter of being the most irradiated icy moon in its respective planetary system, although the energetic electron energy flux at Mimas is forty times smaller than at Europa. High energy (> 10 MeV) proton fluxes are low in this moon's orbital corridor, likely since slowly diffusing protons from the weak but steady source of cosmic ray albedo neutron decay (CRAND) cannot accumulate without impacting the moon surface. Lower energy proton fluxes are also evidently suppressed in this orbital region. Plasma ion and electron fluxes are also low apparently due to cooling by interaction with E-ring dust and neutral gas from Enceladus. Due to energy-dependent effects of longitudinal gradient-curvature drift for the electrons, the trailing hemisphere is mainly irradiated by electrons at energies below 1 MeV that drift relative to Mimas in the prograde direction of orbital motion around Saturn, while higher energy electrons primarily impact the leading hemisphere. Plasma ions in the inner magnetosphere of Saturn are mainly pickup ions forming from the dissociation products of Enceladus plume water molecules, additionally including some contribution from photosputtering of the main rings, and do not introduce new elemental materials at Mimas via surface implantation from the corotating plasma. Thus the primary interaction at the surface is radiolytic chemistry induced in pure water ice by relatively deep penetration of the energetic electrons to millimeter and greater depths, as compared to the micron depths impacted by the corotating plasma ions. If surface erosion by sputtering from relatively low fluxes of the plasma and more energetic ions is indeed ineffective, then molecular products (OH, H2O2, 02, 03) of the radiolytic interactions may accumulate in the meters-deep impact regolith of the surface ices. An effect of regolith trapped gas accumulation could be to increase porosity and reduce thermal conductivity of the ice, potentially contributing to reported thermal anomalies from Cassini infrared map observations. Low amplitude of trailing-leading asymmetry in optical albedo and color maps at Mimas is suggestive of relative weakness of asymmetrical effects from low-energy ions. Greater induced asymmetries are expected and observed for the moons beyond Enceladus in the middle magnetospheric region of hot plasma ions at much greater fluxes than at Mimas. Low density (1.15 g/cc) of this moon indicates paucity of mineral salts and radiogenic heating to maintain subsurface liquids, so Enceladus-like cryovolcanism as a resurfacing process is unlikely despite closer proximity to Saturn, greater tidal forcing, and more intense surface irradiation than for Enceladus.

Cooper, J. F.↗

NASA NTRS2016

Aerosol Complexity and Implications for Predictability and Short-Term Forecasting

There are clear NWP and climate impacts from including aerosol radiative and cloud interactions. Changes in dynamics and cloud fields affect aerosol lifecycle, plume height, long-range transport, overall forcing of the climate system, etc. Inclusion of aerosols in NWP systems has benefit to surface field biases (e.g., T2m, U10m). Including aerosol affects has impact on analysis increments and can have statistically significant impacts on, e.g., tropical cyclogenesis. Above points are made especially with respect to aerosol radiative interactions, but aerosol-cloud interaction is a bigger signal on the global system. Many of these impacts are realized even in models with relatively simple (bulk) aerosol schemes (approx.10 -20 tracers). Simple schemes though imply simple representation of aerosol absorption and importantly for aerosol-cloud interaction particle-size distribution. Even so, more complex schemes exhibit a lot of diversity between different models, with issues such as size selection both for emitted particles and for modes. Prospects for complex sectional schemes to tune modal (and even bulk) schemes toward better selection of size representation. I think this is a ripe topic for more research -Systematic documentation of benefits of no vs. climatological vs. interactive (direct and then direct+indirect) aerosols. Document aerosol impact on analysis increments, inclusion in NWP data assimilation operator -Further refinement of baseline assumptions in model design (e.g., absorption, particle size distribution). Did not get into model resolution and interplay of other physical processes with aerosols (e.g., moist physics, obviously important), chemistry

Predictability↗

NASA NTRS2024

Experimental Validation of Charged Lunar Dust Dynamics Simulants

The goal of this work is to experimentally verify the electrostatic interaction physics that have been incorporated into the discrete element method (DEM) modeling software package during the FY20 CIF project titled “Charged Particle Dynamics in the Lunar Environment.” Current state-of-the-art (SOA) granular gas dynamics models used to explain rocket plume impingement physics have not taken into account the natural or induced electrostatic environment of the lunar surface, nor the effect of charged regolith grains being present in the plume plasma. This work improved upon the SOA by adding long-range and contact inter-particle electrostatic interactions to a granular mechanics DEM modeling software package. Tribocharging mechanics between spherical particles has been experimentally examined along with the natural electrostatic plasma environments produced via emission from an electron gun and ultraviolet lamp.

Jay Phillips↗

NASA NTRSDate not supplied

Monodisperse Single-Material Granular Tribocharging Modeling and Experimental Validation

Charge transfer between insulating grains has been a topic of interest for many years as this phenomenon is extremely important to many areas in industry. Of particular interest to NASA is the behavior of electrically insulative dust grains such as those found on the lunar surface. Whether poured from a scoop during sample collection activities, agitated inside a drum via mining robots, or fluidized by a gas plume, particle-particle interactions between similar granular materials will be widespread on the Moon. Designers hope to have a predictive model for how dust grains are charged, transported, and deposited on flight systems to better understand issues electrostatics may cause in future missions. While difference in work function is often seen as a driver for charge transfer between two materials, this is an incomplete representation for insulative particles. Other asymmetries in the system can also lead to charge being transferred: one such being the difference between static vs dynamic particles. Experiments performed under vacuum in the Electrostatics and Surface Physics Laboratory (ESPL) clearly show that particles having more contacts with other particles tend to charge positively and particles having fewer contacts tend to charge negatively, despite being made from the same material. During these experiments, monodisperse (population of single diameter) spherical particles were held in a reservoir which was then elevated at one end to slope into a Faraday cup used to measure bulk charge of the grains. Care was taken to limit the number of spheres bouncing out of the cup, to isolate the beads from the container itself so that only grain-to-grain interactions occurred, and to assure neutrality of the beads before the experiment began. A discrete element method (DEM) modeling package already incorporating many granular mechanics interactions was augmented to include the electrostatic behaviors seen in experiments. The model can reproduce the experimental results above by tracking the number of contacts between pairs of individual grains and applying a charge transfer condition related to this contact parameter. The experimental results as well as their incorporation into the improved modeling suite will be discussed. Future work includes adding additional asymmetries into the experiments/model such as polydisperse populations of spherical particles and irregularly shaped grains.

granular↗

NASA NTRSDate not supplied

Monodisperse Single-Material Granular Tribocharging Modeling and Experimental Validation

Charge transfer between insulating grains has been a topic of interest for many years as this phenomenon is extremely important to many areas in industry. Of particular interest to NASA is the behavior of electrically insulative dust grains such as those found on the lunar surface. Whether poured from a scoop during sample collection activities, agitated inside a drum via mining robots, or fluidized by a gas plume, particle-particle interactions between similar granular materials will be widespread on the Moon. Designers hope to have a predictive model for how dust grains are charged, transported, and deposited on flight systems to better understand issues electrostatics may cause in future missions. While difference in work function is often seen as a driver for charge transfer between two materials, this is an incomplete representation for insulative particles. Other asymmetries in the system can also lead to charge being transferred: one such being the difference between static vs dynamic particles. Experiments performed under vacuum in the Electrostatics and Surface Physics Laboratory (ESPL) clearly show that particles having more contacts with other particles tend to charge positively and particles having fewer contacts tend to charge negatively, despite being made from the same material. During these experiments, monodisperse (population of single diameter) spherical particles were held in a reservoir which was then elevated at one end to slope into a Faraday cup used to measure bulk charge of the grains. Care was taken to limit the number of spheres bouncing out of the cup, to isolate the beads from the container itself so that only grain-to-grain interactions occurred, and to assure neutrality of the beads before the experiment began. A discrete element method (DEM) modeling package already incorporating many granular mechanics interactions was augmented to include the electrostatic behaviors seen in experiments. The model can reproduce the experimental results above by tracking the number of contacts between pairs of individual grains and applying a charge transfer condition related to this contact parameter. The experimental results as well as their incorporation into the improved modeling suite will be discussed. Future work includes adding additional asymmetries into the experiments/model such as polydisperse populations of spherical particles and irregularly shaped grains.

electrostatics↗

NASA NTRS2010

Ablative Rocket Deflector Testing and Computational Modeling

A deflector risk mitigation program was recently conducted at the NASA Stennis Space Center. The primary objective was to develop a database that characterizes the behavior of industry-grade refractory materials subjected to rocket plume impingement conditions commonly experienced on static test stands. The program consisted of short and long duration engine tests where the supersonic exhaust flow from the engine impinged on an ablative panel. Quasi time-dependent erosion depths and patterns generated by the plume impingement were recorded for a variety of different ablative materials. The erosion behavior was found to be highly dependent on the material s composition and corresponding thermal properties. For example, in the case of the HP CAST 93Z ablative material, the erosion rate actually decreased under continued thermal heating conditions due to the formation of a low thermal conductivity "crystallization" layer. The "crystallization" layer produced near the surface of the material provided an effective insulation from the hot rocket exhaust plume. To gain further insight into the complex interaction of the plume with the ablative deflector, computational fluid dynamic modeling was performed in parallel to the ablative panel testing. The results from the current study demonstrated that locally high heating occurred due to shock reflections. These localized regions of shock-induced heat flux resulted in non-uniform erosion of the ablative panels. In turn, it was observed that the non-uniform erosion exacerbated the localized shock heating causing eventual plume separation and reversed flow for long duration tests under certain conditions. Overall, the flow simulations compared very well with the available experimental data obtained during this project.

Allgood, Daniel C.↗

NASA NTRS1993

Particle kinetic simulation of high altitude hypervelocity flight

In this grant period, the focus has been on the effects of thermo-chemical nonequilibrium in low-density gases, and on interactions between such gases and solid surfaces. Such conditions apply to hypersonic flows of re-entry vehicles, and to the expansion plumes of small rockets. Due to the nonequilibrium nature of these flows, a particle approach has been adopted. The method continues to undergo refinement and application to typical flows of interest. A number of studies have been performed for flows in thermo-chemical nonequilibrium. The effects of vibrational nonequilibrium on the rate of dissociation were studied for diatomic nitrogen. It was found that a new model reproduced the nonequilibrium behavior observed experimentally.

Heinemann, Klaus↗

NASA NTRSDate not supplied

Overview of the Lunar Gateway External Contamination Environment

As a part of the Artemis mission, Gateway will be a long duration space station in a near rectilinear halo orbit around the Moon. Gateway will be exposed to a variety of external contamination sources, which can degrade external hardware / surfaces and impact science utilization objectives. Requirements and methodologies addressing material outgassing, chemical and electric thruster plumes, vacuum venting, and visiting vehicle interactions have been developed by the Gateway Induced Environments team to ensure vehicle performance and mission success. The external contamination requirements and integration process are described along with required data deliverables. Integrated external contamination analyses are conducted by the Gateway Environments Team to assess compliance with external contamination requirements. This paper provides a current status of integration activities and analysis results, as well as future plans to improve external contamination characterization.

Crystal A. Quiroz↗

NASA NTRS2024

Overview of the Lunar Gateway External Contamination Environment

As a part of the Artemis mission, Gateway will be a long duration space station in a near rectilinear halo orbit around the Moon. Gateway will be exposed to a variety of external contamination sources, which can degrade external hardware / surfaces and impact science utilization objectives. Requirements and methodologies addressing material outgassing, chemical and electric thruster plumes, vacuum venting, and visiting vehicle interactions have been developed by the Gateway Induced Environments team to ensure vehicle performance and mission success. The external contamination requirements and integration process are described along with required data deliverables. Integrated external contamination analyses are conducted by the Gateway Environments Team to assess compliance with external contamination requirements. This paper provides a current status of integration activities and analysis results, as well as future plans to improve external contamination characterization.

Crystal A Quiroz↗

NASA NTRSDate not supplied

Overview of the Lunar Gateway External Contamination Environment

As a part of the Artemis mission, Gateway will be a long duration space station in a near rectilinear halo orbit around the Moon. Gateway will be exposed to a variety of external contamination sources, which can degrade external hardware / surfaces and impact science utilization objectives. Requirements and methodologies addressing material outgassing, chemical and electric thruster plumes, vacuum venting, and visiting vehicle interactions have been developed by the Gateway Induced Environments team to ensure vehicle performance and mission success. The external contamination requirements and integration process are described along with required data deliverables. Integrated external contamination analyses are conducted by the Gateway Environments Team to assess compliance with external contamination requirements. This paper provides a current status of integration activities and analysis results, as well as future plans to improve external contamination characterization.

thruster plumes↗

NASA NTRS2021

A lingering local exopshere created by a gas plume of a lunar lander

We model the expected local exosphere created by outgassing from a lunar lander plume water deposit located adjacent to a lunar lander. We assume the landing is near dawn within Lacus Mortis at 45oN. We consider a set of water desorption scenarios especially focusing on the water-surface desorption activation energy that can possess a distribution of energy states. Our initial simulation starts with a deposition surface having 1020 water molecules per square meter in a 2 km × 2 km region where 90% of the water is retained by weak water-water sorption interactions and 10% are bound by water-regolith sorption interactions. We find that the loosely bound water molecules in water-water interactions quickly desorb within hours after landing. However, water molecules bound to surface sites having a desorption activation greater than 0.7 eV were found to be retained until the source region rotated to later local times (i.e., surface temperature becomes relatively high). We found such time-delayed desorption leads to a tenuous but lingering exosphere emitted from the lander plume deposit region for many 10's of hours after landing. We also adjusted the initial condition by considering different landing local times and considered a case where 100% of the water is bound by water-regolith interactions (mimicking a porous regolith).

W.M. Farrell↗

NASA NTRS2004

Supersonic Rocket Thruster Flow Predicted by Numerical Simulation

Despite efforts in the search for alternative means of energy, combustion still remains the key source. Most propulsion systems primarily use combustion for their needed thrust. Associated with these propulsion systems are the high-velocity hot exhaust gases produced as the byproducts of combustion. These exhaust products often apply uneven high temperature and pressure over the surfaces of the appended structures exposed to them. If the applied pressure and temperature exceed the design criteria of the surfaces of these structures, they will not be able to protect the underlying structures, resulting in the failure of the vehicle mission. An understanding of the flow field associated with hot exhaust jets and the interactions of these jets with the structures in their path is critical not only from the design point of view but for the validation of the materials and manufacturing processes involved in constructing the materials from which the structures in the path of these jets are made. The hot exhaust gases often flow at supersonic speeds, and as a result, various incident and reflected shock features are present. These shock structures induce abrupt changes in the pressure and temperature distribution that need to be considered. In addition, the jet flow creates a gaseous plume that can easily be traced from large distances. To study the flow field associated with the supersonic gases induced by a rocket engine, its interaction with the surrounding surfaces, and its effects on the strength and durability of the materials exposed to it, NASA Glenn Research Center s Combustion Branch teamed with the Ceramics Branch to provide testing and analytical support. The experimental work included the full range of heat flux environments that the rocket engine can produce over a flat specimen. Chamber pressures were varied from 130 to 500 psia and oxidizer-to-fuel ratios (o/f) were varied from 1.3 to 7.5.

Davoudzadeh, Farhad↗

NASA NTRS1976

Investigations of the 0.020-scale 88-OTS Integrated Space Shuttle Vehicle Jet-Plume Model in the NASA/Ames Research Center 11 by11-Foot Unitary Plan Wind Tunnel (IA80)

The results are documented of jet plume effects wind tunnel test of the 0.020-scale 88-OTS launch configuration space shuttle vehicle model in the 11 x 11 foot leg of the NASA/Ames Research Center Unitary Plan Wind Tunnel. This test involved cold gas main propulsion system (MPS) and solid rocket motor (SRB) plume simulations at Mach numbers from 0.6 to 1.4. Integrated vehicle surface pressure distributions, elevon and rudder hinge moments, and wing and vertical tail root bending and torsional moments due to MPS and SRB plume interactions were determined. Nozzle power conditions were controlled per pretest nozzle calibrations. Model angle of attack was varied from -4 deg to +4 deg; model angle of sideslip was varied from -4 deg to +4 deg. Reynolds number was varied for certain test conditions and configurations, with the nominal freestream total pressure being 14.69 psia. Plotted force and pressure data are presented.

Nichols, M. E.↗

NASA NTRS2005

Rotating Vessels for Growing Protein Crystals

Rotating vessels have been proposed as means of growing larger, more nearly uniform protein crystals than would otherwise be possible in the presence of normal Earth gravitation. Heretofore, nonrotating vessels have been used. It is difficult to grow high-quality protein crystals in the terrestrial gravitational field because of convection plumes created by the interaction between gravitation and density gradients in protein-solution depletion layers around growing crystals. The density gradients and the associated convection plumes cause the surfaces of growing crystals to be exposed to nonuniform solution densities, thereby causing the crystals to form in irregular shapes. The microgravitational environment of outer space has been utilized to eliminate gravitation-induced convection, but this approach is generally not favorable because of the high cost and limited availability of space flight. The use of a rotating vessel according to the proposal is intended to ameliorate the effects of gravitation and the resultant convection, relative to the corresponding effects in a non-rotating vessel. The rotation would exert an averaging effect over time, distributing the convective force on the depletion layer. Therefore, the depletion layer would be more nearly uniform and, as a result, the growing crystal would be more nearly perfect. The proposal admits of variations (see figure), including the following: The growing crystal could be rotated about its own central axis or an external axis. The crystal-growth vessel could be of any of various shapes, including cylindrical, hemispherical, conical, and combinations thereof. The crystal-growth vessel could be suspended in a viscous fluid in an outer vessel to isolate the growing crystal from both ambient vibrations and vibrations induced by a mechanism that drives the rotation. The rotation could be coupled to the crystal-growth vessel by viscous or magnetic means. The crystal-growth vessel could be supported within the outer vessel by use of a magnetic field. The crystal-growth vessel and the outer vessel could be configured in a variety of ways to facilitate heat transfer, instrumentation, and rotation.

Cottingham, Paul↗

NASA NTRS2012

Numerical Simulation of Rocket Exhaust Interaction with Lunar Soil

This technology development originated from the need to assess the debris threat resulting from soil material erosion induced by landing spacecraft rocket plume impingement on extraterrestrial planetary surfaces. The impact of soil debris was observed to be highly detrimental during NASA s Apollo lunar missions and will pose a threat for any future landings on the Moon, Mars, and other exploration targets. The innovation developed under this program provides a simulation tool that combines modeling of the diverse disciplines of rocket plume impingement gas dynamics, granular soil material liberation, and soil debris particle kinetics into one unified simulation system. The Unified Flow Solver (UFS) developed by CFDRC enabled the efficient, seamless simulation of mixed continuum and rarefied rocket plume flow utilizing a novel direct numerical simulation technique of the Boltzmann gas dynamics equation. The characteristics of the soil granular material response and modeling of the erosion and liberation processes were enabled through novel first principle-based granular mechanics models developed by the University of Florida specifically for the highly irregularly shaped and cohesive lunar regolith material. These tools were integrated into a unique simulation system that accounts for all relevant physics aspects: (1) Modeling of spacecraft rocket plume impingement flow under lunar vacuum environment resulting in a mixed continuum and rarefied flow; (2) Modeling of lunar soil characteristics to capture soil-specific effects of particle size and shape composition, soil layer cohesion and granular flow physics; and (3) Accurate tracking of soil-borne debris particles beginning with aerodynamically driven motion inside the plume to purely ballistic motion in lunar far field conditions. In the earlier project phase of this innovation, the capabilities of the UFS for mixed continuum and rarefied flow situations were validated and demonstrated for lunar lander rocket plume flow impingement under lunar vacuum conditions. Applications and improvements to the granular flow simulation tools contributed by the University of Florida were tested against Earth environment experimental results. Requirements for developing, validating, and demonstrating this solution environment were clearly identified, and an effective second phase execution plan was devised. In this phase, the physics models were refined and fully integrated into a production-oriented simulation tool set. Three-dimensional simulations of Apollo Lunar Excursion Module (LEM) and Altair landers (including full-scale lander geometry) established the practical applicability of the UFS simulation approach and its advanced performance level for large-scale realistic problems.

Liever, Peter↗