SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Oxygen and carbon related defects in silicon, particularly as related to high-efficiency silicon solar cells were studied. A summary of oxygen processes in silicon versus process temperature was shown along with experimental results. The anamolous diffusion of oxygen was explained by the dissociation of the center allowing O sub i to move through the lattices.
The underlying theory of continuous fiber reinforcement of ceramic matrix and resin matrix composites, their fabrication, microstructure, physical and mechanical properties are contrasted. The growing use of organometallic polymers as precursors to ceramic matrices is discussed as a means of providing low temperature processing capability without the fiber degradation encountered with more conventional ceramic processing techniques. Examples of ceramic matrix composites derived from particulate-filled, high char yield polymers and silsesquioxane precursors are provided.
In order to describe the total mineralogical diversity within primitive extraterrestrial materials, individual interplanetary dust particles (IDPs) collected from the stratosphere as part of the JSC Cosmic Dust Curatorial Program were analyzed using a variety of AEM techniques. Identification of over 250 individual grains within one chondritic porous (CP) IDP shows that most phases could be formed by low temperature processes and that heating of the IDP during atmospheric entry is minimal and less than 600 C. In a review of the mineralogy of IDPs, it was suggested that the occurrence of other silicates such as enstatite whiskers is consistent with the formation in an early turbulent period of the solar nebula. Experimental confirmation of fundamental chemical and physical processes in a stellar environment, such as vapor phase condensation, nucleation, and growth by annealing, is an important aspect of astrophysical models for the evolution of the Solar System. A detailed comparison of chondritic IDP and carbonaceous chondrite mineralogies shows significant differences between the types of silicate minerals as well as the predominant oxides.
The paper surveys current information, describes some important unknowns about lunar materials, and discusses ways to gain more scientific and engineering knowledge concerning the industrial processes that could be used on the moon for the production of products useful in future enterprises in space. Lunar rocks and soils are rich in oxygen, but it is mostly chemically bound in silicates, so that chemical or thermal energy must be supplied to recover it. Iron and titanium are abundant and, in some of their known forms, readily recoverable; aluminum is plentiful but harder to extract. Methods for recovering lunar oxygen and metals fall into three classes: chemical, electrolytic, and dissociative, broadly characterized by their respective process temperatures. Examples of these methods are briefly discussed.
A new type of GaAs is developed which exhibits inverted thermal conversion (ITC); i.e., it converts from conducting to semiinsulating upon annealing at about 850 C. In device fabrication, its low resistivity prior to high-temperature processing differentiates ITC GaAs from the standard semiinsulating GaAs. The ITC characteristics are obtained through control of the concentration of the midgap donor EL2 based on heat treatment and crystal-growth modification. Thus EL2 does not exist in the conducting state of ITC GaAs. Conversion to the semiinsulating state during 850 C annealing is caused by the formation of EL2.
Phosphorus nitride (PN) has been detected in the interstellar medium. The J = 2-1, 3-2, 5-4, and 6-5 rotational lines of this species have been observed toward Orion-KL, and the J = 2-1 transition in Sgr B2 and W51. The PN line profiles in Orion indicate that the molecule's emission arises from the 'plateau' or 'doughnut' region associated with the outflow from IRc2. The species is thus primarily present in hot, dense gas. Column densities derived for PN toward Orion-KL are (3-4) x 10 to the 13th/sq cm, but may be as high as 10 to the 14th/sq cm, if the species is located in a 10-arcsec region. These column densities imply a fractional abundance for PN in the Orion 'plateau' of (1-4) x 10 to the -10th. Such a large abundance for PN is not predicted by quiescent cloud ion-molecule chemistry and suggests that high-temperature processes are responsible for the synthesis of PN in the KL outflow.
The underlying theory of continuous fiber reinforcement of ceramic matrix and resin matrix composites, their fabrication, microstructure, physical and mechanical properties are contrasted. The growing use of organometallic polymers as precursors to ceramic matrices is discussed as a means of providing low temperature processing capability without the fiber degradation encountered with more conventional ceramic processing techniques. Examples of ceramic matrix composites derived from particulate-filled, high char yield polymers and silsesquioxane precursors are provided.
Silicon dioxide glasses containing 15 mole percent magnesium oxide prepared by sol-gel process. Not made by conventional melting because ingredients immiscible liquids. Synthesis of MgO/SiO2 glass starts with mixing of magnesium nitrate hexahydrate with silicon tetraethoxide, both in alcohol. Water added, and transparent gel forms. Subsequent processing converts gel into glass. Besides producing glasses of new composition at lower processing temperatures, sol-gel method leads to improved homogeneity and higher purity.
Due to the thermal expansion coefficient mismatch (CTE) between the fiber and the matrix, high residual sresses exist in metal matrix composite systems upon cool down from processing temperature to room temperature. An interface material can be placed between the fiber and the matrix to reduce the high tensile residual stresses in the matrix. A computer program was written to minimize the residual stress in the matrix subject to the interface material properties. The decision variables are the interface modulus, thickness and thermal expansion coefficient. The properties of the interface material are optimized such that the average distortion energy in the matrix and the interface is minimized. As a result, the only active variable is the thermal expansion coefficient. The optimum modulus of the interface is always the minimum allowable value and the interface thickness is always the maximum allowable value, independent of the fiber/matrix system. The optimum interface thermal expansion coefficient is always between the values of the fiber and the matrix. Using this analysis, a survey of materials was conducted for use as fiber coatings in some specific composite systems.
The thermoelastic micromechanical stresses associated with a single large hexagonal alpha-SiC grain within a fine-grain-size cubic (3C) beta-SiC matrix were calculated. The naturally occurring residual stresses which are created during cooling from the processing temperatures and the effects of superimposed applied external stresses are both considered. A significant effect of the shape or geometry of the alpha-SiC grain is revealed, with the largest residual stresses associated with the naturally occurring tabular or platelet structure. The stresses are compared with the published strength results for these materials, which suggests that the residual stresses assume a significant role in the strength reduction that is observed.
A number of polymers of differing molecular structure, viscosity, copolymer composition, and production procedures, screened for production of strong, tough Nicalon/siliconoxycarbide composites, are discussed. Variables during polymer synthesis include pH, water/methoxy ratio and phenyl/methyl ratio. Final processing temperatures of the composites range from 1200 deg to 1400 deg C. The filler is derived from pyrolysis of the 50 phenyl/50 methyl silsesquioxane copolymer pyrolyzed to 650 deg C, then milled to less than 1-micron powder. Composite samples were fractured to evaluate the influence of matrix composition, final fabrication temperature, and use of filler on the composite mode of failure, modulus, strain capability, and strength. Incorporation of filler was found to increase matrix compressive strength and to influence matrix shrinkage and cracking.
High residual stresses within intermetallic and metal matrix composite systems can develop upon cooling from the processing temperature to room temperature due to the coefficient of thermal expansion (CTE) mismatch between the fiber and matrix. As a result, within certain composite systems, radial, circumferential, and/or longitudinal cracks have been observed to form at the fiber-matrix interface. The compliant layer concept (insertion of a compensating interface material between the fiber and matrix) was proposed to reduce or eliminate the residual stress buildup during cooling and thus minimize cracking. The viability of the proposed compliant layer concept is investigated both elastically and elastoplastically. A detailed parametric study was conducted using a unit cell model consisting of three concentric cylinders to determine the required character (i.e., thickness and material properties) of the compliant layer as well as its applicability. The unknown compliant layer mechanical properties were expressed as ratios of the corresponding temperature dependent Ti-24Al-11Nb (a/o) matrix properties. The fiber properties taken were those corresponding to SCS-6 (SiC). Results indicate that the compliant layer can be used to reduce, if not eliminate, radial and circumferential residual stresses within the fiber and matrix and therefore also reduce or eliminate the radial cracking. However, with this decrease in in-plane stresses, one obtains an increase in longitudinal stress, thus potentially initiating longitudinal cracking. Guidelines are given for the selection of a specific compliant material, given a perfectly bonded system.
Report presents review of principal thermoplastics (TP's) used to fabricate high-performance composites. Sixteen principal TP's considered as candidates for fabrication of high-performance composites presented along with names of suppliers, Tg, Tm (for semicrystalline polymers), and approximate maximum processing temperatures.
Because of the inherent coefficient of thermal expansion (CTE) mismatch between fiber and matrix within metal and intermetallic matrix composite systems, high residual stresses can develop under various thermal loading conditions. These conditions include cooling from processing temperature to room temperature as well as subsequent thermal cycling. As a result of these stresses, within certain composite systems, radial, circumferential, and/or longitudinal cracks have been observed to form at the fiber matrix interface region. A number of potential solutions for reducing this thermally induced residual stress field have been proposed recently. Examples of some potential solutions are high CTE fibers, fiber preheating, thermal anneal treatments, and an engineered interface. Here the focus is on designing an interface (by using a compensating/compliant layer concept) to reduce or eliminate the thermal residual stress field and, therefore, the initiation and propagation of cracks developed during thermal loading. Furthermore, the impact of the engineered interface on the composite's mechanical response when subjected to isothermal mechanical load histories is examined.
Aluminum carbide may form at aluminum-graphite interfaces during the high-temperature processing of graphite fiber-reinforced aluminum metal matrix composites. The chemical interactions leading to the formation of the aluminum carbide in the solid state involve the breaking of the carbon-carbon bonds within the graphite, the transport of the carbon atoms across the interface, and the reaction with the aluminum to form Al4C3. The aluminum carbide formation process has been followed using X-ray photoelectron spectroscopy of model, thin-film, reaction couples. The overall reaction is shown to be catalyzed by the presence of water vapor. Water at the interface increases reaction kinetics by apparently weakening the bonds between the surface carbon atoms and their substrate. This result is in general agreement with what is known to occur during the oxidation of graphite in air.
High residual stresses within metal and intermetallic matrix composite systems can develop upon cooling from the processing temperature to room temperature due to the coefficient of thermal expansion (CTE) mismatch between the fiber and matrix. As a result, within certain composite systems, radial, circumferential, and/or longitudinal cracks have been observed to form at the fiber-matrix interface region. The compliant layer concept (insertion of a compensating interface material between the fiber and matrix) has been proposed to reduce or eliminate the residual stress buildup during cooling, and thus minimize cracking. The present study investigates elastic-plastically the viability of the proposed compliant layer concept. A detailed parametric study was conducted utilizing a unit cell model consisting of three concentric cylinders to determine the required character (i.e., thickness and mechanical properties) of the compliant layer as well as its applicability. The unknown compliant layer mechanical properties were expressed as ratios of the corresponding temperature dependent Ti-24Al-11Nb (a/o) matrix properties. The fiber properties taken were those corresponding to SCS-6 (SiC). Results indicated that the compliant layer can be used to reduce, if not eliminate, radial and circumferential residual stresses within the fiber and matrix and therefore also reduce or eliminate the radial cracking. However, with this decrease in in-plane stresses, one obtains an increase in longitudinal stress, thus potentially initiating longitudinal cracking. Guidelines are given for the selection of a specific compensating/ compliant material, given a perfectly bonded system.
To produce lunar cement, high-temperature processing will be required. It may be possible to make calcium-rich silicate and aluminate for cement by solar heating of lunar pyroxene and feldspar, or chemical treatment may be required to enrich the calcium and aluminum in lunar soil. The effects of magnesium and ferrous iron present in the starting materials and products would need to be evaluated. So would the problems of grinding to produce cement, mixing, forming in vacuo and low gravity, and minimizing water loss.
The topics are presented in viewgraph form and include the following: mass and composition; photochemical processes; temperatures and winds; general circulation; and dust storms.