SEARCH · Search NASA

Results for “Proton conducting fuel cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS2007

High Altitude Long Endurance Air Vehicle Analysis of Alternatives and Technology Requirements Development

The objective of this study was to develop a variety of High Altitude Long Endurance (HALE) Unmanned Aerial Vehicle (UAV) conceptual designs for two operationally useful missions (hurricane science and communications relay) and compare their performance and cost characteristics. Sixteen potential HALE UAV configurations were initially developed, including heavier-than-air (HTA) and lighter-than-air (LTA) concepts with both consumable fuel and solar regenerative (SR) propulsion systems. Through an Analysis of Alternatives (AoA) down select process, the two leading consumable fuel configurations (one each from the HTA and LTA alternatives) and an HTA SR configuration were selected for further analysis. Cost effectiveness analysis of the consumable fuel configurations revealed that simply maximizing vehicle endurance can lead to a sub-optimum system solution. An LTA concept with a hybrid propulsion system (solar arrays and a hydrogen-air proton exchange membrane fuel cell) was found to have the best mission performance; however, an HTA diesel-fueled wing-body-tail configuration emerged as the preferred consumable fuel concept because of the large size and technical risk of the LTA concept. The baseline missions could not be performed by even the best HTA SR concept. Mission and SR technology trade studies were conducted to enhance understanding of the potential capabilities of such a vehicle. With near-term technology SR-powered HTA vehicles are limited to operation in favorable solar conditions, such as the long days and short nights of summer at higher latitudes. Energy storage system specific energy and solar cell efficiency were found to be the key technology areas for enhancing HTA SR performance.

Nickol, Craig L.↗

DOE OSTI2024

Materials descriptors for advanced water dissociation catalysts in bipolar membranes

The voltage penalty driving water dissociation (WD) at high current density is a major obstacle in the commercialization of bipolar membrane (BPM) technology for energy devices. Here, in this study, we show that three materials descriptors, that is, electrical conductivity, microscopic surface area and (nominal) surface-hydroxyl coverage, effectively control the kinetics of WD in BPMs. Using these descriptors and optimizing mass loading, we design new earth-abundant WD catalysts based on nanoparticle SnO 2 synthesized at low temperature with high conductivity and hydroxyl coverage. These catalysts exhibit exceptional performance in a BPM electrolyser with low WD overvoltage (η wd ) of 100 ± 20 mV at 1.0 A cm -2 . The new catalyst works equivalently well with hydrocarbon proton-exchange layers as it does with fluorocarbon-based Nafion, thus providing pathways to commercializing advanced BPMs for a broad array of electrolysis, fuel-cell and electrodialys is applications.

Sasmal, Sayantan↗

DOE OSTI2021

Fluorine-Free Precise Polymer Electrolyte for Efficient Proton Transport: Experiments and Simulations

Designing polymers with controlled nanoscale morphologies and scalable synthesis is of great interest in the development of fluorine-free materials for proton-exchange membranes in fuel cells. This study focuses on a precision polyethylene with phenylsulfonic acid branches at every fifth carbon, p5PhSA, with a high ion-exchange capacity (4.2 mmol/g). The polymers self-assemble into hydrophilic and hydrophobic co-continuous nanoscale domains. In the hydrated state, the hydrophilic domain, composed of polar sulfonic acid moieties and water, serves as a pathway for efficient mesoscopic proton conductivity. The morphology and proton transport of p5PhSA are evaluated under hydrated conditions using in situ X-ray scattering and electrochemical impedance spectroscopy techniques. Additionally, at 40 °C and 95% relative humidity, the proton conductivity of p5PhSA is 0.28 S/cm, which is four times greater than Nafion 117 under the same conditions. Atomistic molecular dynamics (MD) simulations are also used to elucidate the interplay between the structure and the water dynamics. The MD simulations show strong nanophase separation between the percolated hydrophilic and hydrophobic domains over a wide range of water contents. The percolated hydrophilic nanoscale domain facilitates the rapid proton transport in p5PhSA and demonstrates the potential of precise hydrocarbon-based polymers as processible and effective proton-exchange membranes.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Modeling the Environment-Dependent Kinetics of Oxygen Reduction Reaction – a Continuum Model for Electric Double Layer

Here, for proton-exchange-membrane fuel cells (PEMFCs) to achieve broad commercialization, improved energy-conversion efficiency with minimal Pt-based electrocatalyst is required. Because the sluggish rate of oxygen reduction reaction (ORR) limits the efficiency of PEMFCs, the efficiency improvement requires a better understanding of ORR kinetics and mechanism to design better catalyst. To understand the ORR mechanism, theoretical and experimental analyses have been conducted. While previous studies reasonably explained the catalyst-dependent activity on single crystal catalysts in 0.1 M perchloric acid solution, the explicit effect of electrolyte and related microenvironments is not thoroughly understood. The change in the electrolyte alters the electric-double-layer (EDL) structure and thus the local microenvironment at the electrode/electrolyte interface. Thus, the structure of the EDL should be carefully analyzed to uncover the electrolyte-dependent reaction kinetics. In this talk, we propose a multiscale continuum model to predict the EDL structure and examine the effect of perchloric acid concentration on ORR activity on Pt (111). The model includes Density Potential Functional Theory (DPFT) for electron density and Modified Poisson Boltzmann equation for species’ density and electric potential. Also, the interaction between adsorbents and electric field is taken into account by minimizing the grand potential. After model validation with experimentally measured double-layer capacity data as a function of applied potential and concentration, the effect of the perchloric acid concentration (0.02 M – 0.2 M) on ORR activity is analyzed and discussed. It is shown that the model reproduces the specific activity obtained in the experiments when assuming the oxygen adsorption is limiting the rate, which can be attributed to the large energetic barrier for solvent reorganization. Then, extension of the model to PEMFC ionomer electrolytes will be introduced. Overall, the model framework and findings provide insights into the ORR mechanism and guidance on how to tailor catalyst materials for increased PEMFC performance.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

Low-Pressure Electrolytic Ammonia (LPEA) Production

The project goal was to advance and demonstrate the techno-economic viability of a low-pressure electrolytic ammonia (LPEA) process for producing ammonia from electricity, hydrogen, and nitrogen. The critical enabling technology of the LPEA process is a proton-conducting electrolyte (PCE) developed by EERC and North Dakota State University (NDSU) capable of high proton conductivity (at least 1×10 -2 [0.01] siemens/centimeter [S/cm]) at 200°–300°C. An affordable PCE that works at 200°–300°C has been a major goal of the global electrochemistry industry for over 25 years, because it would enable operation at temperatures high enough to prevent catalyst poisoning and simplify water management and low enough to avoid temperature-driven degradation of fuel cell components comprising materials with differing coefficients of thermal expansion. Also critical to LPEA performance is a cathode catalyst capable of ammonia synthesis at a rate of ≥1×10 -10 moles/second-cm 2 catalyst surface area (mol-s -1 cm -2 ) in screening tests conducted at room temperature, and 1×10 -7 mol-s -1 cm -2 at 200°–300°C for commercial viability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

HydroGEN Consortium: Advancements in Hydrogen Production

HydroGEN Energy Materials Network (EMN) is an U.S. Department of Energy (DOE) EERE Hydrogen and Fuel Cell Technologies Office (HFTO)-funded consortium that aims to accelerate the discovery and development of advanced water splitting materials (AWSM) for clean, low-cost hydrogen production. Materials innovations are key to enhancing performance, durability, and cost of hydrogen generation technologies. HydroGEN is focused on low technology readiness level AWS technologies, including low- (alkaline exchanged membrane electrolysis) and high-temperature electrolysis (proton-conducting solid oxide electrolysis), photoelectrochecmical (PEC) and thermochemical (TCH) water splitting. The AWS technologies in this consortium study proton conduction in solid oxide electrolysis and hydroxide conduction in polymer electrolysis, and proton transport in photoelectrochemical water splitting. This presentation will provide an overview of the HydroGEN EMN and technical highlights of a few lab-led and DOE-awarded "seedling" R&D projects. HydroGEN continues to grow its community of industry, university, and national laboratories, forming a national innovation ecosystem focused on renewable hydrogen production.

08 HYDROGEN↗

DOE OSTI2026

HydroGEN Consortium

08 HYDROGEN↗

DOE OSTI2024

HydroGEN Consortium: Advancements in Renewable Hydrogen Production

HydroGEN Energy Materials Network (EMN) is an U.S. Department of Energy (DOE) EERE Hydrogen and Fuel Cell Technologies Office (HFTO)-funded consortium that aims to accelerate the discovery and development of advanced water splitting materials (AWSM) for clean, low-cost hydrogen production. Materials innovations are key to enhancing performance, durability, and cost of hydrogen generation technologies. HydroGEN is focused on low technology readiness level AWS technologies, including low- (alkaline exchanged membrane electrolysis) and high-temperature electrolysis (proton-conducting solid oxide electrolysis), photoelectrochecmical (PEC) and solar thermochemical (STCH) water splitting. This presentation will provide an overview of the HydroGEN EMN and technical highlights of a few lab-led and FOA-awarded R&D projects. HydroGEN continues to grow its community of industry, university, and national laboratories, forming a national innovation ecosystem focused on renewable hydrogen production.

clean hydrogen↗

DOE OSTI2022

Electrocatalysis in Alkaline Media and Alkaline Membrane-Based Energy Technologies

Hydrogen energy-based electrochemical energy conversion technologies offer the promise of enabling a transition of the global energy landscape from fossil fuels to renewable energy. Here, we present a comprehensive review of the fundamentals of electrocatalysis in alkaline media and applications in alkaline-based energy technologies, particularly alkaline fuel cells and water electrolyzers. Anion exchange (alkaline) membrane fuel cells (AEMFCs) enable the use of nonprecious electrocatalysts for the sluggish oxygen reduction reaction (ORR), relative to proton exchange membrane fuel cells (PEMFCs), which require Pt-based electrocatalysts. However, the hydrogen oxidation reaction (HOR) kinetics is significantly slower in alkaline media than in acidic media. Understanding these phenomena requires applying theoretical and experimental methods to unravel molecular-level thermodynamics and kinetics of hydrogen and oxygen electrocatalysis and, particularly, the proton-coupled electron transfer (PCET) process that takes place in a proton-deficient alkaline media. Extensive electrochemical and spectroscopic studies, on single-crystal Pt and metal oxides, have contributed to the development of activity descriptors, as well as the identification of the nature of active sites, and the rate-determining steps of the HOR and ORR. Among these, the structure and reactivity of interfacial water serve as key potential and pH-dependent kinetic factors that are helping elucidate the origins of the HOR and ORR activity differences in acids and bases. Additionally, deliberately modulating and controlling catalyst-support interactions have provided valuable insights for enhancing catalyst accessibility and durability during operation. The design and synthesis of highly conductive and durable alkaline membranes/ionomers have enabled AEMFCs to reach initial performance metrics equal to or higher than those of PEMFCs. We emphasize the importance of using membrane electrode assemblies (MEAs) to integrate the often separately pursued/optimized electrocatalyst/support and membranes/ionomer components. Operando/in situ methods, at multiscales, and ab initio simulations provide a mechanistic understanding of electron, ion, and mass transport at catalyst/ionomer/membrane interfaces and the necessary guidance to achieve fuel cell operation in air over thousands of hours. We hope that this Review will serve as a roadmap for advancing the scientific understanding of the fundamental factors governing electrochemical energy conversion in alkaline media with the ultimate goal of achieving ultralow Pt or precious-metal-free high-performance and durable alkaline fuel cells and related technologies.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2020

Single Cobalt Sites Dispersed in Hierarchically Porous Nanofiber Networks for Durable and High-Power PGM-Free Cathodes in Fuel Cells

Increasing catalytic activity and durability of atomically dispersed metal–nitrogen–carbon (M–N–C) catalysts for the oxygen reduction reaction (ORR) cathode in proton-exchange-membrane fuel cells remains a grand challenge. In this study, a high-power and durable Co–N–C nanofiber catalyst synthesized through electrospinning cobalt-doped zeolitic imidazolate frameworks into selected polyacrylonitrile and poly(vinylpyrrolidone) polymers is reported. The distinct porous fibrous morphology and hierarchical structures play a vital role in boosting electrode performance by exposing more accessible active sites, providing facile electron conductivity, and facilitating the mass transport of reactant. The enhanced intrinsic activity is attributed to the extra graphitic N dopants surrounding the CoN 4 moieties. The highly graphitized carbon matrix in the catalyst is beneficial for enhancing the carbon corrosion resistance, thereby promoting catalyst stability. The unique nanoscale X-ray computed tomography verifies the well-distributed ionomer coverage throughout the fibrous carbon network in the catalyst. The membrane electrode assembly achieves a power density of 0.40 W cm –2 in a practical H 2 /air cell (1.0 bar) and demonstrates significantly enhanced durability under accelerated stability tests. The combination of the intrinsic activity and stability of single Co sites, along with unique catalyst architecture, provide new insight into designing efficient PGM-free electrodes with improved performance and durability.

25 ENERGY STORAGE↗

DOE OSTI2025

Scalable Solution-Processed Electrolyte Membranes with Optimized Microstructure for High-Performance Protonic Ceramic Electrochemical Cells

Proton-conducting electrochemical cells (PCECs) are promising for efficient hydrogen production, but achieving dense, uniform, thin electrolyte layers remains a key challenge, particularly for scalable fabrication. Here, we present a solution-processed deposition approach with a mechanistically optimized slurry for uniform electrolyte formation. By tailoring particle size distribution, solid loading, and solvent/additive balance, we regulated wetting behavior and evaporation kinetics of the electrolyte slurry to promote homogeneous electrolyte particle packing. These features facilitate tight grain boundary contact and early stage neck growth during sintering, eliminating residual porosity, and improving mechanical integrity. The resulting ∼15 μm thick electrolyte shows high density, strong electrode adhesion, and stable interfaces outperforming the previously reported spray-based fabricated electrolyte by about 31% at 600 °C in FC mode. Single cells deliver 0.962 W cm –2 at 600 °C in fuel cell mode and 1.31 A cm –2 at 1.3 V in electrolysis mode, maintaining robust performance over 100 h with negligible degradation (≤0.02% h –1 ) in each mode. Scale-up to 2.5 cm diameter substrates confirmed reproducible densification and geometric stability. This work demonstrates a cost-effective, scalable route where control over particle-fluid interactions and drying dynamics enables a superior electrolyte microstructure and high PCEC performance.

dense microstructure↗

DOE OSTI2026

Public Reference Data for Megawatt-Scale Hydrogen Electrolysis - NLR Historical Wind

The U.S. Department of Energy and the National Laboratory of the Rockies (NLR) demonstrate hydrogen electrolysis from variable sources, hydrogen compression and storage, and hydrogen fuel cell power production using megawatt-scale equipment at NLR’s Flatirons Campus as part of the Advanced Research on Integrated Energy Systems (ARIES) initiative. This dataset represents part of that effort and is intended for academic, national laboratory, industrial, and other stakeholders to plan, design, and validate models of megawatt-scale hydrogen technologies and diverse energy infrastructure nationwide. These data provide a baseline for how existing hydrogen electrolysis technologies perform when coupled with various energy technologies. Future datasets will demonstrate how existing hydrogen fuel cell technologies can provide controllable, dispatchable, and variable power output for artificial intelligence (AI) data centers and other variable loads. This dataset entry describes hydrogen production by conducting a statistical analysis of historical wind data over a five-year period (2020-2025) from a single 1.5MW turbine manufactured by General Electric (GE) located at NLR’s Flatirons Campus, to generate an experimental test profile that was deployed on a 1.25-MW proton exchange membrane type MC250 electrolyzer system manufactured by Nel Hydrogen . [1] While the electrolyzer balance-of-plant supports up to 2.5 MW of electrolysis, NLR only has a single 1.25-MW electrolysis stack. The historical wind data provided several metrics, however, the analysis particularly focused on the measured power output by the wind turbine. The power output time series of data for each day was categorized by total energy generation and standard deviation, and the day that represented the highest combination of these two metrics was chosen – December 25th, 2022. This process was then repeated for a moving four-hour window within this day to identify the most statistically variable period. Finally, this four-hour period was scaled by 65% to match the 1.25 MW electrolyzer. The electrolysis system controls hydrogen production by varying DC current applied to the stack, from a maximum of 3000 A to a minimum safe operation of 300 A, or 10%. Because the current – voltage characteristic changes as the stack ages and efficiency degrades, the actual minimum safe operating power changes over time. The historical wind profiles were translated from power (kilowatts) to current (amperes) using a curve fit with calibration data and sent to the electrolyzer power supply at 1 Hz frequency. For more details on the statistical analysis process, see the presentation labeled “ Public Reference Data for Megawatt-Scale Hydrogen Electrolysis” provided with each data entry. These datasets report relevant hydrogen balance-of-plant and system data, all captured at 1 Hz, including hydrogen mass production measured with an Emerson Coriolis flow meter. Each .zip file represents a single wind turbine electrolysis experiment and is formatted as follows: {technology}_{scaling factor}-{electrolyzer ramp rate in amperes/second} For instance, “wind-GE1.5MW_0.65-400.zip” represents the hour-long experiment using historical data from the wind-GE1.5MW turbine, scaled to 65%, with the electrolyzer power supply set to a maximum ramp rate (gain and slew) of 400 A/s. Each .zip folder contains the following files: A .csv file containing raw data An .xlsx file explaining all the fields in the raw data. A .png plot showing the time series of hydrogen production, electrolysis power consumption, and wind power input. A PDF file detailing the historical wind data statistical analysis used to generate the wind profile. An experiment labeled “characterization_200.zip” demonstrates the MC250 electrolyzer steady-state response with 30-minute load steps for a total duration of 5 hours. Finally, a .csv file is provided with all simulated wind experiments combined into one dataset labeled "combined_historical_wind_experiments.csv". NLR also built an AI/machine-learning predictive model based on these datasets. The model ingests the electrolyzer current command in amperes, as well as various pressures and temperatures across the system, and predicts hydrogen output in kilograms per hour. The complete model can be found at https://huggingface.co/NatLabRockies/ptmelt-hydrogen-electrolysis [1] nelhydrogen.com/product/mc-series-electrolyser .

08 HYDROGEN↗

DOE OSTI2022

An Unbalanced Battle in Excellence: Revealing Effect of Ni/Co Occupancy on Water Splitting and Oxygen Reduction Reactions in Triple–Conducting Oxides for Protonic Ceramic Electrochemical Cells

Porous electrodes that conduct electrons, protons, and oxygen ions with dramatically expanded catalytic active sites can replace conventional electrodes with sluggish kinetics in protonic ceramic electrochemical cells. In this work, a strategy is utilized to promote triple conduction by facilitating proton conduction in praseodymium cobaltite perovskite through engineering non-equivalent B-site Ni/Co occupancy. Surface infrared spectroscopy is used to study the dehydration behavior, which proves the existence of protons in the perovskite lattice. The proton mobility and proton stability are investigated by hydrogen/deuterium (H/D) isotope exchange and temperature-programmed desorption. It is observed that the increased nickel replacement on the B-site has a positive impact on proton defect stability, catalytic activity, and electrochemical performance. This doping strategy is demonstrated to be a promising pathway to increase catalytic activity toward the oxygen reduction and water splitting reactions. The chosen PrNi 0.7 Co 0.3 O 3–δ oxygen electrode demonstrates excellent full-cell performance with high electrolysis current density of –1.48 A cm –2 at 1.3 V and a peak fuel-cell power density of 0.95 W cm –2 at 600 °C and also enables lower-temperature operations down to 350 °C, and superior long-term durability.

08 HYDROGEN↗

DOE OSTI2020

Highly Durable and Active Pt/Sb-Doped SnO 2 Oxygen Reduction Reaction Electrocatalysts Produced by Atomic Layer Deposition

Platinum supported on mixed-metal oxides (MMOs) are a class of active and durable cathode catalysts for proton exchange membrane fuel cell (PEMFC) due to a combination of the high oxidative stability of the supports and strong-metal-support interactions (SMSI) that enable them to exceed the activity of Pt/C. Herein, we solve a significant remaining challenge with Pt/MMO systems, namely the relatively low surface area and porosity. This is achieved by dispersing nearly-uniform Pt clusters using atomic layer deposition (ALD) on highly conductive (6.2 S/cm) and stable antimony doped tin dioxide (ATO) support. ALD-Pt/ATO exhibited significantly higher electrochemically active surface area (ECSA) (74 m 2 /g) and oxygen reduction reaction (ORR) catalytic activity (102 mA/mg Pt at 0.9 V vs. RHE) compared to Pt/ATO synthesized using ethylene glycol (ECSA=31 m 2 /g Pt , mass activity=52 mA/mg Pt at 0.9 V vs. RHE) and formic acid reduction methods (ECSA=28 m 2 /g Pt , mass activity=46 mA/mg Pt at 0.9 V vs. RHE). Further characterization showed that wet chemical methods resulted in poorer Pt particle dispersion, poor control over Pt particle size distribution and chemical degradation of the support (during Pt deposition). Given the near-ideal Pt particle size distribution of the ALD-Pt/ATO, particle size growth and loss of ECSA was found to be minimal over the course of rigorous potential cycling. Thus, after 10,000 potential cycles between 1V and 1.5V vs. RHE, ALD-Pt/ATO and other Pt/ATOs were found to retain 100% of their initial ECSA compared to 57.6% retention for Pt/C. Upon testing in a H 2 /air PEMFC, following 1,000 potential cycles, the change in ALD-Pt/ATO performance was negligible while Pt/C exhibited a 68.2% loss of initial peak power density. Thus, ALD-Pt/ATO is an active and highly durable ORR electrocatalyst in PEMFCs under start-up-shut down conditions.

25 ENERGY STORAGE↗

DOE OSTI2020

Influence of Water Transport Across Microscale Bipolar Interfaces on the Performance of Direct Borohydride Fuel Cells

Direct borohydride fuel cells (DBFCs) can operate at double the voltage of proton exchange membrane fuel cells (PEMFCs) by employing an alkaline NaBH 4 fuel feed and an acidic H 2 O 2 oxidant feed. The pH-gradient-enabled microscale bipolar interface (PMBI) facilitates the creation and maintenance of an alkaline environment at the anode and an acidic environment at the cathode for the borohydride oxidation and peroxide reduction reactions. However, given the need to dissociate water at the interface to ensure ionic conduction, PMBI can be efficient only when anion exchange ionomer (AEI) moieties enable fast water transport for autoprotolysis. Herein, a series of polynorbornene-based AEIs with a range of water uptake values are examined to unravel the optimum water uptake required to enable high performance DBFCs. The DBFC with PMBI configuration containing the optimal AEI composition delivers a current density of 302 mA cm –2 at 1.5 V and a peak power density of 580 mW cm –2 at 1 V. This AEI composition exhibits high hydroxide ionic conductivity of 90.7 mS cm –1 at 80 °C with an IEC of 2.01 mequiv g –1 and demonstrates impressive chemical stability by retaining 98.75% of its initial ionic conductivity after immersion into anolyte (3 M KOH and 1.5 M NaBH 4 ) at 70 °C for 536 h.

25 ENERGY STORAGE↗

NASA NTRS1995

SPE(R)-OBOGS: On-board oxygen generating sustem

Regulations require oxygen usage by commercial airline flight crews during check out and during certain aircraft configurations. This oxygen is drawn from a high pressure onboard pressure cylinder storage system. In a typical aircraft oxygen cylinder removal for oxygen ground servicing is conducted every 4 to 6 weeks. An on board oxygen generating system has been developed to eliminate the need for oxygen ground servicing. The SPE-OBOGS supplies oxygen during flight in a 'trickle charge' mode to replenish the consumed oxygen at pressures up to 1850 psi. The Electrochemical cell stack is the fundamental SPE-OBOGS system component. The same basic proton exchange membrane technology, previously used for the Gemini program fuel cells and currently used in nuclear submarines as oxygen generators, is used in the SPE-OBOGS. An in-serivce evaluation of the SPE-OBOGS is in the planning stage and a zero gravity version is being promoted for on orbit space suit oxygen system recharge. Summary results of the SPE-OBOGS development will be addressed.

Mcelroy, J.↗

NASA NTRS2005

Improved Anode for a Direct Methanol Fuel Cell

A modified chemical composition has been devised to improve the performance of the anode of a direct methanol fuel cell. The main feature of the modified composition is the incorporation of hydrous ruthenium oxide into the anode structure. This modification can reduce the internal electrical resistance of the cell and increase the degree of utilization of the anode catalyst. As a result, a higher anode current density can be sustained with a smaller amount of anode catalyst. These improvements can translate into a smaller fuel-cell system and higher efficiency of conversion. Some background information is helpful for understanding the benefit afforded by the addition of hydrous ruthenium oxide. The anode of a direct methanol fuel cell sustains the electro-oxidation of methanol to carbon dioxide in the reaction CH3OH + H2O--->CO2 + 6H(+) + 6e(-). An electrocatalyst is needed to enable this reaction to occur. The catalyst that offers the highest activity is an alloy of approximately equal numbers of atoms of the noble metals platinum and ruthenium. The anode is made of a composite material that includes high-surface-area Pt/Ru alloy particles and a proton-conducting ionomeric material. This composite is usually deposited onto a polymer-electrolyte (proton-conducting) membrane and onto an anode gas-diffusion/current-collector sheet that is subsequently bonded to the proton-conducting membrane by hot pressing. Heretofore, the areal density of noble-metal catalyst typically needed for high performance has been about 8 mg/cm2. However, not all of the catalyst has been utilized in the catalyzed electro-oxidation reaction. Increasing the degree of utilization of the catalyst would make it possible to improve the performance of the cell for a given catalyst loading and/or reduce the catalyst loading (thereby reducing the cost of the cell). The use of carbon and possibly other electronic conductors in the catalyst layer has been proposed for increasing the utilization of the catalyst by increasing electrical connectivity between catalyst particles. However, the relatively low density of carbon results in thick catalyst layers that impede the mass transport of methanol to the catalytic sites. Also, the electrical conductivity of carbon is less than 1/300th of typical metals. Furthermore, the polymer-electrolyte membrane material is acidic and most metals are not chemically stable in contact with it. Finally, a material that conducts electrons (but not protons) does not contribute to the needed transport of protons produced in the electro-oxidation reaction.

Valdez, Thomas↗

DOE OSTI2026

Improving protonic ceramic electrochemical cell performance via a dual-phase reaction-sintered bilayer electrolyte

Protonic ceramic electrochemical cells (PCCs) are promising energy conversion devices, but their fabrication remains challenging. In particular, the typical electrolytes for PCCs such as BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3−δ (7111) and BaCe 0.4 Zr 0.4 Y 0.1 Yb 0.1 O 3−δ (4411) suffer from intrinsic barium evaporation issues during high-temperature sintering. This tendency towards barium loss, combined with their highly refractory nature, leads to a tradeoff between sinterability and chemical stability. To address this tradeoff, we propose a bilayer electrolyte combining layers of 4411 and 7111 materials that is designed to enhance sinterability and conductivity through dual-phase reactive sintering. Our findings demonstrate that the bilayer structure exhibits shrinkage behavior closely matched to that of the fuel electrode substrate, with a higher shrinkage compared to a single-layer 4411 electrolyte. Utilizing this bilayer electrolyte structure, our PCCs achieve a peak power density of 637 mW∙cm −2 in fuel-cell mode and a current density of 1060 mA∙cm −2 at 1.3 V in electrolysis mode at 600 °C. Our PCCs demonstrate high Faradaic efficiency of 83% at 1.3 V and 500 °C. Hybrid distribution of relaxation times (DRT) polarization mapping further reveals that the bilayer structure reduces Ohmic and polarization resistance in both fuel-cell and electrolysis modes.

ceramic processing↗