Search NASA⌕ Search

SEARCH · Search NASA

Results for “Pulsed laser deposition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Sliding Wear and Fretting Wear of DLC-Based, Functionally Graded Nanocomposite Coatings

Improving the tribological functionality of diamondlike carbon (DLC) films--developing, good wear resistance, low friction, and high load-carrying capacity-was the aim of this investigation. Nanocomposite coatings consisting of an amorphous DLC (a-DLC) top layer and a functionally graded titanium-titanium carbon-diamondlike carbon (Ti-Ti(sub x) C(sub y)-DLC) underlayer were produced on AISI 440C stainless steel substrates by the hybrid technique of magnetron sputtering and pulsed-laser deposition. The resultant DLC films were characterized by Raman spectroscopy, scanning electron microscopy, and surface profilometry. Two types of wear experiment were conducted in this investioation: sliding friction experiments and fretting wear experiments. Unidirectional ball-on-disk sliding friction experiments were conducted to examine the wear behavior of an a-DLC/Ti-Ti(sub x) C(sub y)-DLC-coated AISI 440C stainless steel disk in sliding contact with a 6-mm-diameter AISI 440C stainless steel ball in ultrahigh vacuum, dry nitrogen, and humid air. Although the wear rates for both the coating and ball were low in all three environments, the humid air and dry nitrogen caused mild wear with burnishing, in the a-DLC top layer, and the ultrahigh vacuum caused relatively severe wear with brittle fracture in both the a-DLC top layer and the Ti-Ti(sub x) C(sub y)-DLC underlayer. For reference, amorphous hydrogenated carbon (H-DLC) films produced on a-DLC/Ti-Ti(sub x) C(sub y)-DLC nanocomposite coatings by using an ion beam were also examined in the same manner. The H-DLC films markedly reduced friction even in ultrahigh vacuum without sacrificing wear resistance. The H-DLC films behaved much like the a-DLC/Ti-Ti(sub x) C(sub y)-DLC nanocomposite coating in dry nitrogen and humid air, presenting low friction and low wear. Fretting wear experiments were conducted in humid air (approximately 50% relative humidity) at a frequency of 80 Hz and an amplitude of 75 micron on an a-DLC/Ti-Ti(sub x) C(sub y)-DLC-coated AISI 440C disk and on a titanium-6 wt % aluminum-4 wt% vanadium (Ti-6Al-4V) flat, both in contact with a 9.4-mm-diameter, hemispherical Ti-6Al-4V pin. The resistance to fretting wear and damage of the a-DLC/Ti-6Al-4V materials pair was superior to that of the Ti-6Al-4V/Ti-6AI-4V materials pair.

Miyoshi, K.↗
NASA NTRS2005

Feasibility study of ferromagnetic/ferroelectric films for enhanced microwave devices

This report summarizes exploratory work conducted to assess the feasibility of ferromagnetic/ferroelectric films for next-generation microwave devices. From literature review, it is established that while an increasing number of ferroelectric/ferromagnetic composites are being investigated, a number have transition temperatures that are too low and structures that are not robust enough for low cost, room temperature antenna arrays. On the other hand, several promising systems are identified, including the multiferroic BiFeO3 and a composite system of Ba/SrTiO3 and a related perovskite manganite. It is suggested that when the NASA pulsed laser deposition chamber is fully operational, thin films of these systems be investigated. In preparation for such work, we have reconfirmed several structural features of an existing Ba/SrTiO3 film using the x-ray diffractometer at Oberlin College.

Ijiri, Yumi↗
NASA NTRS2007

High Temperature Protonic Conductors

High Temperature Protonic Conductors (HTPC) with the perovskite structure are envisioned for electrochemical membrane applications such as H2 separation, H2 sensors and fuel cells. Successive membrane commercialization is dependent upon addressing issues with H2 permeation rate and environmental stability with CO2 and H2O. HTPC membranes are conventionally fabricated by solid-state sintering. Grain boundaries and the presence of intergranular second phases reduce the proton mobility by orders of magnitude than the bulk crystalline grain. To enhanced protonic mobility, alternative processing routes were evaluated. A laser melt modulation (LMM) process was utilized to fabricate bulk samples, while pulsed laser deposition (PLD) was utilized to fabricate thin film membranes . Sr3Ca(1+x)Nb(2-x)O9 and SrCe(1-x)Y(x)O3 bulk samples were fabricated by LMM. Thin film BaCe(0.85)Y(0.15)O3 membranes were fabricated by PLD on porous substrates. Electron microscopy with chemical mapping was done to characterize the resultant microstructures. High temperature protonic conduction was measured by impedance spectroscopy in wet air or H2 environments. The results demonstrate the advantage of thin film membranes to thick membranes but also reveal the negative impact of defects or nanoscale domains on protonic conductivity.

Dynys, Fred↗
NASA NTRS2010

Thin-Film Ferro Electric-Coupled Microstripline Phase Shifters With Reduced Device Hysteresis

This work deals with the performance of coupled microstripline phase shifters (CMPS) fabricated using BaxSr 1 -xTiO 3 (BST) ferroelectric thin films. The CMPS were fabricated using commercially available pulsed laser deposition BST films with Ba:Sr ratios of 30:70 and 20:80. Microwave characterization of these CMPS was performed at upper Kuband frequencies, particularly at frequencies near 16 and 18 GHz. X-ray diffraction studies indicate that the 30:70 films exhibit almost a 1:1 ratio between the in-plane and out-of-plane lattice parameters, suggesting that their cubics create strain -free films suitable for producing CMPS devices with reduced hysteresis in the paraelectric state. The quality of performance of the CMPS was studied based on their relative phase shift and insertion loss within the DC bias range of 0 to 400 V (i.e., E-field ranges within 0 to 53 V/micron). The performance of the CMPS was tested as a function of temperature to investigate their operation in the paraelectric, as well as in the ferroelectric, state (i.e., above and below the Curie temperature, respectively). The novel behavior discussed here is based on the experimental observation of the CMPS. This behavior, observed for the aforementioned cation ratio, highlights the relevance of good crystalline structure for high-quality CMPS.

Miranda, Felix A.↗
NASA NTRS2017

Optical Properties of Ar Ions Irradiated Nanocrystalline ZrC and ZrN Thin Films

Thin nanocrystalline ZrC and ZrN films (less than 400 nanometers), grown on (100) Si substrates at a substrate temperature of 500 degrees Centigrade by the pulsed laser deposition (PLD) technique, were irradiated by 800 kiloelectronvolts Ar ion irradiation with fluences from 1 times 10(sup 14) atoms per square centimeter up to 2 times 10(sup 15) atoms per square centimeter. Optical reflectance data, acquired from as-deposited and irradiated films, in the range of 500-50000 per centimeter (0.06–6 electronvolts), was used to assess the effect of irradiation on the optical and electronic properties. Both in ZrC and ZrN films we observed that irradiation affects the optical properties of the films mostly at low frequencies, which is dominated by the free carriers response. In both materials, we found a significant reduction in the free carriers scattering rate, i.e. possible increase in mobility, at higher irradiation flux. This is consistent with our previous findings that irradiation affects the crystallite size and the micro-strain, but it does not induce major structural changes.

ZrN↗
NASA NTRS2019

1.6-μm Er:YGG Waveguide Amplifiers

We report on the fabrication and characterization of Er:YGG films suitable for waveguide amplifiers that could in principle be used in integrated path differential absorption lidar systems. Presented is our fabrication technique, comprising pulsed-laser-deposition growth of ~10 μm-thick crystalline films, their channeling via ultraprecision ductile dicing with a diamond-blade, producing optical quality facets and sidewalls, and amplifier performance. Net gain at 1572 nm and 1651 nm is obtained for the first time in Er-doped YGG waveguide amplifiers. Additionally, in a channel waveguide a maximum internal gain of 3.5 dB/cm at the 1533nm peak was realized. Recent crystal film quality improvements promise further performance enhancements needed for the intended application for high-peak power sources in the 1.6-μm spectral region targeting Earth observation systems for monitoring greenhouse gases.

greenhouse gases; planar waveguide amplifiers↗
DOE OSTI2026

Oxide-nitride heteroepitaxy for low-loss dielectrics in superconducting quantum circuits

Superconducting qubits show great promise for the realization of fault-tolerant quantum computing, but lossy, amorphous dielectrics limit current technology. Identifying highly crystalline and stoichiometric dielectrics with intrinsically low microwave loss is therefore a central materials challenge, yet experimentally validated platforms remain scarce. In this work, we integrate a crystalline dielectric into a heteroepitaxial TiN/$γ$-Al$_2$O$_3$/TiN trilayer grown via pulsed laser deposition. Correlative high-resolution imaging, diffraction, and spectroscopy measurements confirm the single-crystal quality and chemical integrity of all layers, with minimal defects and limited anion interdiffusion across the oxide-nitride interfaces. Using microwave lumped-element resonators with parallel-plate capacitors, we report the first direct measurement of the dielectric loss of epitaxial $γ$-Al$_2$O$_3$, for which we find a low intrinsic two-level system loss, $δ_{\text{TLS}}^0 = (2.8 \pm 0.1) \times 10^{-5}$. These results establish heteroepitaxial oxides on transition metal nitrides as an attractive materials platform for superconducting quantum circuits, particularly for integration into compact device architectures such as merged-element transmons and microwave kinetic inductance detectors.

Garcia-Wetten, David A. [Northwestern U.]↗
DOE OSTI2024

A DFT-based kinetic Monte Carlo simulation of multiphase oxide-metal thin film growth

Functional thin films of nanoscale metal pillars in oxide or nitride matrices known as vertically aligned nanocomposite (VAN) have gained much interest owing to their unique strain-coupled and highly anisotropic properties. So far, the deposition of these films has been explored mostly experimentally. In this work, a density functional theory (DFT)-based kinetic Monte Carlo simulation model using Bortz–Kalos–Lebowitz algorithm was developed to understand the growth of VAN films deposited by pulsed laser technique on mismatching substrates. The model has been parameterized and applied to understand the kinetics of growth thin films consisting of Au pillars in CeO2 matrix deposited on SrTiO3 substrates. The effects of pulsed laser deposition (PLD) conditions including the pulse frequency, deposition flux, and substrate temperature were explored. The simulations indicate that the Au pillar size and shape exhibit significant dependence on the PLD conditions. Namely, increasing the temperature increases the average pillar size and lowers the pillar density, and vice versa. In addition, the simulations revealed that increasing the deposition rate results in lowering the average pillar size and increasing the density. Particularly, the DFT results suggest that Au pillar size can be tuned during the initial growth of the first monolayer due to the significantly low activation barrier. Our analysis showed that the relationship between the average pillar size and pillar density is influenced by the kinetics. Furthermore, autocorrelation analysis showed that pillars self-organize in quasi-ordered patterns at certain windows of the deposition conditions, which is attributed to the complex nature of the chemical interactions in the system, the kinetics, and the deposition parameters.

Physics↗
NASA NTRS1990

Thermal diffusivity of diamond films using a laser pulse technique

Polycrystalline diamond films were deposited using a microwave plasma-enhanced chemical vapor deposition process. A laser pulse technique was developed to measure the thermal diffusivity of diamond films deposited on a silicon substrate. The effective thermal diffusivity of a diamond film on silicon was measured by observing the phase and amplitude of the cyclic thermal waves generated by laser pulses. An analytical model is presented to calculate the effective in-plane (face-parallel) diffusivity of a two-layer system. The model is used to reduce the effective thermal diffusivity of the diamonds/silicon sample to a value for the thermal diffusivity and conductivity of the diamond film. The average effective diffusivity values are 1.47 + or - 0.03 and 1.83 + or - 0.10 yielding thermal diffusivity values of 7.46 + or - 0.90 and 7.33 + or - 0.70 sq cm/s respectively, for the two samples; the calculated thermal con ductivity values are 13.50 and 13.28 W/cmK, which are better than that of type 1a natural diamond. The phase and amplitude measurements give similar results.

Albin, Sacharia↗
DOE OSTI2020

Collinear dual-pulse laser optical breakdown and energy deposition

A non-equilibrium model for laser-generated plasmas is used to represent collinear dual nano-second-pulse interactions. In the specific case considered, the breakdown is initiated with an ultraviolet (UV) laser pulse at 266 nm, which pre-ionizes the gas, and it is followed by a near-infrared (NIR) pulse at 1064 nm, which deposits significant energy into the ionized mixture. The model is validated against corresponding experiments, and simulation results are interrogated to understand key features of the plasma-kernel dynamics and the post-discharge hydrodynamics. The hydrodynamics of the non-equilibrium plasma is governed by the two-temperature Navier–Stokes equations accounting for both multiphoton ionization and inverse bremsstrahlung. The interaction between the laser beam and the plasma is modeled based on the radiative transfer equation. The temporal and spatial offsets of the two pulses can generate ionization kernels with different topology and dynamics. It is shown that the UV pre-ionization pulse can tailor the plasma region, leading to a larger ionized volume than would occur for a single-pulse breakdown, and it increases the efficiency of the energy deposition for the following NIR discharge. Vorticity in the early post-discharge phase is generated via baroclinic torque from the misalignment of the radial gradient of density (sudden gas expansion) and the strong pressure gradient (initiated by energy deposition from the laser beam). It is predicted that the collinear dual pulse can be designed to specify the plasma kernel size, shape, and maximum temperature in the breakdown phase, and the initial post-breakdown vorticity and plasma-core decay.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1991

Deposition of high quality YBa2Cu3O(7-delta) thin films over large areas by pulsed laser ablation with substrate scanning

The paper describes thin films deposited in a system where substrates are scanned over areas up to 3.5 x 3.5 cm through the stationary plume of an ablated material defined by an aperture. These YBCO films are deposited on LaAlO3 and SrTiO3 substrates with the thickness of 90 and 160 nm. Attention is focused on the main features of the deposition system: line focusing of the laser beam on the target; an aperture defining the area of the plume; computerized stepper motor-driven X-Y stage translating the heated sampler holder behind the plume-defining aperture in programmed patterns; and substrate mounting block with uniform heating at high temperatures over large areas. It is noted that the high degree of uniformity of the properties in each film batch illustrates that the technique of pulsed laser deposition can be applied to produce large YBCO films of high quality.

Davis, M. F.↗
DOE OSTI2021

Epitaxy of LiNbO 3 : Historical Challenges and Recent Success

High-quality epitaxial growth of thin film lithium niobate (LiNbO 3 ) is highly desirable for optical and acoustic device applications. Despite decades of research, current state-of-the-art epitaxial techniques are limited by either the material quality or growth rates needed for practical devices. In this paper, we provide a short summary of the primary challenges of lithium niobate epitaxy followed by a brief historical review of lithium niobate epitaxy for prevalent epitaxial techniques. Available figures of merit for crystalline quality and optical transmission losses are given for each growth method. The highest crystalline quality lithium niobate thin film was recently grown by halide-based molecular beam epitaxy and is comparable to bulk lithium niobate crystals. However, these high-quality crystals are grown at slow rates that limit many practical applications. Given the many challenges that lithium niobate epitaxy imposes and the wide variety of methods that have unsuccessfully attempted to surmount these barriers, new approaches to lithium niobate epitaxy are required to meet the need for simultaneously high crystalline quality and sufficient thickness for devices not currently practical by existing techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2020

New approaches for achieving more perfect transition metal oxide thin films

This perspective considers the enormous promise of epitaxial functional transition metal oxide thin films for future applications in low power electronic and energy applications since they offer wide-ranging and highly tunable functionalities and multifunctionalities, unrivaled among other classes of materials. It also considers the great challenges that must be overcome for transition metal oxide thin films to meet what is needed in the application domain. These challenges arise from the presence of intrinsic defects and strain effects, which lead to extrinsic defects. Current conventional thin film deposition routes often cannot deliver the required perfection and performance. Since there is a strong link between the physical properties, defects and strain, routes to achieving more perfect materials need to be studied. Several emerging methods and modifications of current methods are presented and discussed. The reasons these methods better address the perfection challenge are considered and evaluated.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Recent Advances in Vertically Aligned Nanocomposites with Tunable Optical Anisotropy: Fundamentals and Beyond

Developing reliable and tunable metamaterials is fundamental to next-generation optical-based nanodevices and computing schemes. In this review, an overview of recent progress made with a unique group of ceramic-based functional nanocomposites, i.e., vertically aligned nanocomposites (VANs), is presented, with the focus on the tunable anisotropic optical properties. Using a self-assembling bottom-up deposition method, the as-grown VANs present great promise in terms of structural flexibility and property tunability. Such broad tunability of functionalities is achieved through VAN designs, material selection, growth control, and strain coupling. The as-grown multi-phase VAN films also present enormous advantages, including wafer scale integration, epitaxial quality, sharp atomic interface, as well as designable materials and geometries. This review also covers the research directions with practical device potentials, such as multiplex sensing, high-temperature plasmonics, magneto-optical switching, as well as photonic circuits.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Intrinsic exchange bias from interfacial reconstruction in an epitaxial Ni x Co y Fe 3– x – y O 4 (111)/α-Al 2 O 3 (0001) thin film family

Intrinsic exchange bias is known as the unidirectional exchange anisotropy that emerges in a nominally single-component ferro-(ferri-)magnetic system. In this work, with magnetic and structural characterizations, we demonstrate that intrinsic exchange bias is a general phenomenon in (Ni, Co, Fe)-based spinel oxide films deposited on α-Al 2 O 3 (0001) substrates, due to the emergence of a rock-salt interfacial layer consisting of antiferromagnetic CoO from interfacial reconstruction. We show that in Ni x Co y Fe 3–x–y O 4 (111)/α-Al 2 O 3 (0001) films, intrinsic exchange bias and interfacial reconstruction have consistent dependences on Co concentration y, while the Ni and Fe concentration appears to be less important. This work establishes a family of intrinsic exchange bias materials with great tunability by stoichiometry and highlights the strategy of interface engineering in controlling material functionalities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Molybdenum Disulfide Nanoribbons with Enhanced Edge Nonlinear Response and Photoresponsivity

MoS 2 nanoribbons have attracted increased interest due to their properties, which can be tailored by tuning their dimensions. Herein, the growth of MoS 2 nanoribbons and triangular crystals formed by the reaction between films of MoOx (2 2 nanoribbons arising from distinct contributions from the single–layer edges and multilayer core. Nanoscale imaging reveals a blue-shifted exciton emission of the monolayer edge compared to the isolated MoS 2 monolayers due to built-in local strain and disorder. We further report on an ultrasensitive photodetector made of a single MoS 2 nanoribbon with a responsivity of 8.72 × 10 2 A W –1 at 532 nm, among the highest reported up-to-date for single-nanoribbon photodetectors. These findings can inspire the design of MoS 2 semiconductors with tunable geometries for efficient optoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High‐throughput combinatorial approach expedites the synthesis of a lead‐free relaxor ferroelectric system

Abstract Developing novel lead‐free ferroelectric materials is crucial for next‐generation microelectronic technologies that are energy efficient and environment friendly. However, materials discovery and property optimization are typically time‐consuming due to the limited throughput of traditional synthesis methods. In this work, we use a high‐throughput combinatorial synthesis approach to fabricate lead‐free ferroelectric superlattices and solid solutions of (Ba 0.7 Ca 0.3 )TiO 3 (BCT) and Ba(Zr 0.2 Ti 0.8 )O 3 (BZT) phases with continuous variation of composition and layer thickness. High‐resolution x‐ray diffraction (XRD) and analytical scanning transmission electron microscopy (STEM) demonstrate high film quality and well‐controlled compositional gradients. Ferroelectric and dielectric property measurements identify the “optimal property point” achieved at the composition of 48BZT–52BCT. Displacement vector maps reveal that ferroelectric domain sizes are tunable by varying {BCT–BZT} N superlattice geometry. This high‐throughput synthesis approach can be applied to many other material systems to expedite new materials discovery and properties optimization, allowing for the exploration of a large area of phase space within a single growth. image

36 MATERIALS SCIENCE↗
DOE OSTI2023

Revealing Site Occupancy in a Complex Oxide: Terbium Iron Garnet

Complex oxide films stabilized by epitaxial growth can exhibit large populations of point defects which have important effects on their properties. The site occupancy of pulsed laser-deposited epitaxial terbium iron garnet (TbIG) films with excess terbium (Tb) is analyzed, in which the terbium:iron (Tb:Fe)ratio is 0.86 compared to the stoichiometric value of 0.6. The magnetic properties of the TbIG are sensitive to site occupancy, exhibiting a higher compensation temperature (by 90 K) and a lower Curie temperature (by 40 K) than the bulk Tb 3 Fe 5 O 12 garnet. Data derived from X-ray core-level spectroscopy, magnetometry, and molecular field coefficient modeling are consistent with occupancy of the dodecahedral sites by Tb 3+ , the octahedral sites by Fe 3+ , Tb 3+ and vacancies, and the tetrahedral sites by Fe 3+ and vacancies. Energy dispersive X-ray spectroscopy in a scanning transmission electron microscope provides direct evidence of Tb Fe antisites. A small fraction of Fe 2+ is present, and oxygen vacancies are inferred to be present to maintain charge neutrality. In conclusion, variation of the site occupancies provides a path to considerable manipulation of the magnetic properties of epitaxial iron garnet films and other complex oxides, which readily accommodate stoichiometries not found in their bulk counterparts.

36 MATERIALS SCIENCE↗