Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reaction Kinetics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Ordering in the Fe-Ni system under electron irradiation

The disorder-order transformation was generated in a range of Fe-Ni alloys using 1 MeV electrons in a high voltage electron microscope. The experimental factors that influence the occurrence of the transformation were determined, and the critical disordering temperature, Tc, was determined as a function of composition. It was demonstrated that the irradiation enhanced the ordering reaction kinetics. A metastable, ordered phase transformation was not induced. From the results, it is possible to deduce new information about the Fe-Ni phase diagram below 350 C.

Reuter, K. B.↗
NASA NTRS1989

Oxidation of chemically-vapor-deposited silicon nitride and single-crystal silicon

The present 1000 C and 1300 C oxidation tests on 111-oriented single-crystal Si and dense CVD Si3N4 notes the oxidation rates of the latter in wet O2, dry O2, wet inert gas, and steam atmosphere conditions to be several orders of magnitude lower than the rates for the former in identical atmospheric conditions. Although the parabolic rate constant for Si increased linearly as the water vapor pressure increased, the parabolic rate constant for Si3N4 exhibited a nonlinear dependency on water vapor pressure in the presence of O2. NO and NH3 formation at the reaction interface of Si3N4, and the counterpermeation of these reaction products, are noted to dominate reaction kinetics.

Choi, Doo J.↗
NASA NTRS1987

Arcjet thruster research and technology. Phase 1: Executive summary

The principal objective of this two phase program is to conduct the development research required to make the low power arcjet a flight ready technology. Many important results were obtained during Phase 1 to move closer to this objective. Fundamental analyses were performed of the arcjet nozzle, the gas kinetic reaction effects, the thermal environment, and the arc stabilizing vortex. These aided the conceptual understanding of the arcjet and guided design work. A hydrazine (N2H4) arcjet was designed that combined a flight qualified catalyst bed with a modular arcjet. Extensive testing was performed which demonstrated the feasibility of using this propellant in an arcjet for the first time. Startup techniques were developed, stability maintained, material compatibility tests conducted, and performance mapping tests performed. Specific impulse values from 400 to 730 seconds were produced with a non-optimized design. These levels are higher than were originally thought possible and proved that extremely high enthalpy values can be obtained with constricted arc technology. Erosion rate data are promising for lifetime extensions to meet flight application requirements. Power control unit (PCU) development was started with the design and fabrication of a laboratory high switching frequency supply. Valuable data were obtained on PCU operation and on the interaction with the dynamic arc. Phase 2 efforts presently underway are resolving key issues for multi-hundred hour lifetimes, are continuing to investigate arcjet/PCU interactions, and will demonstrate duty cycle N2H4 arcjet/PCU operation in a simulated flight mode for lifetimes consistent with initial applications.

Source record↗
NASA NTRS1990

Electron-impact ionization and electron attachment cross sections of radicals important in transient gaseous discharges

Electron-impact ionization and electron attachment cross sections of radicals and excited molecules were measured using an apparatus that consists of an electron beam, a molecular beam and a laser beam. The information obtained is needed for the pulse power applications in the areas of high power gaseous discharge switches, high energy lasers, particle beam experiments, and electromagnetic pulse systems. The basic data needed for the development of optically-controlled discharge switches were also investigated. Transient current pulses induced by laser irradiation of discharge media were observed and applied for the study of electron-molecule reaction kinetics in gaseous discharges.

Lee, Long C.↗
NASA NTRS1990

Selective removal of organics for water reclamation

Electrooxidation is a means of removing organic solutes directly from waste waters without the use of chemical expendables. The feasibility of the concept for oxidation of organic impurities common to urine, shower waters and space habitat humidity condensates was demonstrated. Electrooxidation of urine and waste water ersatz was experimentally demonstrated. The electrooxidation principle, reaction kinetics, efficiency, power, size, experimental test results and water reclamation applications are described. Process operating potentials and the use of anodic oxidation potentials that are sufficiently low to avoid oxygen formation and chloride oxidation are also described. The design of a novel electrochemical system that incorporates a proton exchange membrane (PEM) electrolyte is presented based on parametric test data and current fuel cell technology.

Murphy, Oliver J.↗
NASA NTRS1990

Synthesis of Y1Ba2Cu3O(sub x) superconducting powders by intermediate phase reaction

One of the more striking problems for the synthesis of the Y1Ba2Cu3Ox compound is the high-temperature decomposition of the BaCO3. This compound is present as raw material or as an intermediate compound in chemical processes such as amorphous citrate, coprecipitation oxalate, sol-gel process, acetate pyrolisis, etc. This fact makes difficult the total formation reaction of the Y1Ba2Cu3Ox phase and leads to the presence of undesirable phases such as the BaCuO2 phase, the 'green phase', Y2BaCuO5 and others. Here, a new procedure to overcome this difficulty is studied. The barium cation is previously combined with yttrium and/or copper to form intermediate compounds which can react between them to give Y1Ba2Cu3Ox. BaY2O4 and BaCu2O3 react according to the equation BaY2O4+3BaCu2O3 yields 2Y1Ba2Cu3Ox. BaY2O4 is a stable compound of the Y2O3-BaO system; BaCu2O3 is an intimate mixture of BaCuO2 and uncombined CuO. The reaction kinetics of these phases have been established between 860 and 920 C. The phase evolution has been determined. The crystal structure of the Y1Ba2Cu3Ox obtained powder was studied. According to the results obtained from the kinetics study the Y1Ba2Cu3Ox the synthesis was performed at temperatures of 910 to 920 C for short treatment times (1 to 2 hours). Pure Y1Ba2Cu3Ox was prepared, which develops orthorombic type I structure despite of the cooling cycle. Superconducting transition took place at 91 K. The sintering behavior and the superconducting properties of sintered samples were studied. Density, microstructure and electrical conductivity were measured. Sintering densities higher than 95 percent D(sub th) were attained at temperatures below 940 C. Relatively fine grained microstructure was observed, and little or no-liquid phase was detected.

Moore, C.↗
NASA NTRS1991

Semiconductor structural damage attendant to contact formation in III-V solar cells

In order to keep the resistive losses in solar cells to a minimum, it is often necessary for the ohmic contacts to be heat treated to lower the metal-semiconductor contact resistivity to acceptable values. Sintering of the contacts, however can result in extensive mechanical damage of the semiconductor surface under the metallization. An investigation of the detailed mechanisms involved in the process of contact formation during heat treatment may control the structural damage incurred by the semiconductor surface to acceptable levels, while achieving the desired values of contact resistivity for the ohmic contacts. The reaction kinetics of sintered gold contacts to InP were determined. It was found that the Au-InP interaction involves three consecutive stages marked by distinct color changes observed on the surface of the Au, and that each stage is governed by a different mechanism. A detailed description of these mechanisms and options to control them are presented.

Fatemi, Navid S.↗
NASA NTRS1991

Carbon monoxide and oxygen combustion experiments: A demonstration of Mars in situ propellants

The feasibility of using carbon monoxide and oxygen as rocket propellants was examined both experimentally and theoretically. The steady-state combustion of carbon monoxide and oxygen was demonstrated for the first time in a subscale rocket engine. Measurements of experimental characteristic velocity, vacuum specific impulse, and thrust coefficient efficiency were obtained over a mixture ratio range of 0.30 to 2.0 and a chamber pressures of 1070 and 530 kPa. The theoretical performance of the propellant combination was studied parametrically over the same mixture ratio range. In addition to one dimensional ideal performance predictions, various performance reduction mechanisms were also modeled, including finite-rate kinetic reactions, two-dimensional divergence effects and viscous boundary layer effects.

Linne, Diane L.↗
NASA NTRS1991

Investigation of the effect of thermal exposure on the mechanical properties of titanium/SiC composites

The objective was to evaluate the influence of thermal exposure, both isothermal and cyclic, on the reaction kinetics, mechanical properties and fracture behavior of Ti-1100 alloy/SiC fiber composites. Previously, it was determined that composites made with TiB2 coated SiC fiber (sigma) reacted at the same rate as SCS-6 fibers. As a result, the thinner surface coating on the Sigma fiber was completely consumed at shorter times than that on the SCS-6. Thermal cycling experiments were conducted on longitudinal and transverse Ti-1100/SCS-6 composites over a temperature range of 150 to 800 C for 500 cycles. The thermal exposures were carried out in air and argon. No appreciable tensile strength degradation was observed for samples cycled in argon, although a strength loss was noted for the samples cycled in air. Fracture surfaces characterization showed brittle matrix failure in regions near the surface and in regions where there was a path for O2 ingress.

Gundel, Douglas B.↗
NASA NTRS1990

Interpretation of aircraft measurements of NO, ClO, and O3 in the lower stratosphere

Results are presented from an October 17, 1988, flight of the NASA ER-2 stratospheric research aircraft. The flight sampled a nearly constant air mass at 20 km altitude, near 39 deg N latitude, from before sunrise until near noon. The instrumentation on board simultaneously measured NO, ClO, O3, temperature, and pressure. The measurements are combined with modeled photodissociation coefficients and known reaction kinetics to infer abundances of other important species, and the results are compared to previous estimates as a test for consistency in the understanding of the photochemical processes governing the species distributions.

Kawa, S. R.↗
NASA NTRS1991

UV spectroscopy of Titan's atmosphere, planetary organic chemistry and prebiological synthesis. II - Interpretation of new IUE observations in the 220-335 nm range

The theoretical model developed by McKay et al. (1989) to characterize the size distribution, thermal structure, and chemical composition of the stratospheric haze of Titan is applied to new 220-335-nm albedo measurements obtained with the long-wavelength prime camera of the IUE during August 1987. Data and model predictions are presented in extensive graphs and discussed in detail. It is shown that a simple model with particles of one size at a given altitude does not accurately reproduce the observed features in all spectral regions, but that good general agreement is obtained using a model with a uniformly mixed layer at 150-600 km and a bimodal distribution of small 'polymer' haze particles (radius less than 20 nm) and larger haze particles (radius 100-500 nm). The number densities implied by this model require, however, a mechanism such as electrostatic charging or reaction kinetics to inhibit coagulation of the smaller particles.

Courtin, Regis↗
NASA NTRS1991

Carbon monoxide and oxygen combustion experiments - A demonstration of Mars in situ propellants

The feasibility of using carbon monoxide and oxygen as rocket propellants was examined both experimentally and theoretically. The steady-state combustion of carbon monoxide and oxygen was demonstrated for the first time in a subscale rocket engine. Measurements of experimental characteristic velocity, vacuum specific impulse, and thrust coefficient efficiency were obtained over a mixture ratio range of 0.30 to 2.0 and a chamber pressures of 1070 and 530 kPa. The theoretical performance of the propellant combination was studied parametrically over the same mixture ratio range. In addition to one dimensional ideal performance predictions, various performance reduction mechanisms were also modeled, including finite-rate kinetic reactions, two-dimensional divergence effects and viscous boundary layer effects.

Linne, Diane L.↗
NASA NTRS1990

Electrooxidation of organics in waste water

Electrooxidation is a means of removing organic solutes directly from waste waters without the use of chemical expendables. Research sponsored by NASA is currently being pursued to demonstrate the feasibility of the concept for oxidation of organic impurities common to urine, shower waters and space-habitat humidity condensates. Electrooxidation of urine and waste water ersatz was experimentally demonstrated. This paper discusses the electrooxidation principle, reaction kinetics, efficiency, power, size, experimental test results and water-reclamation applications. Process operating potentials and the use of anodic oxidation potentials that are sufficiently low to avoid oxygen formation and chloride oxidation are described. The design of an electrochemical system that incorporates a membrane-based electrolyte based on parametric test data and current fuel-cell technology is presented.

Hitchens, G. D.↗
NASA NTRS1991

Detonability of hydrocarbon fuels in air

Studies were conducted of the detonation of gas-phase mixtures of n-hexane and JP-4, with oxidizers as varied as air and pure oxygen, measuring detonation velocities and cell sizes as a function of stoichiometry and diluent concentration. The induction length of a one-dimensional Zeldovich-von Neumann-Doering detonation was calculated on the basis of a theoretical model that employed the reaction kinetics of the hydrocarbon fuels used. Critical energy and critical tube diameter are compared for a relative measure of the heavy hydrocarbon fuels studied; detonation sensitivity appears to increase slightly with increasing carbon number.

Beeson, H. D.↗
NASA NTRS1991

Synthesis of Y1BaCu3O(x) superconducting powders by intermediate phase reactions

A procedure for synthesizing Y1Ba2Cu3O(x) by solid state reactions was developed. The method is based on the use of barium compounds, previously synthesized, as intermediate phases for the process. The reaction kinetics of this procedure were established between 860 C and 920 C. The crystal structure and the presence of second phases were studied by means of XRD. The sintering behavior and ceramic parameters were also determined. The orthorhombic type-I structure was obtained on the synthesized bodies after a cooling cycle in an air atmosphere. Superconducting transition took place at 91 K. Sintering densities higher than 95 percent D sub th were attained at temperatures below 940 C.

Moure, C.↗
NASA NTRS1992

Carbonate formation on Mars: History of the CO2 atmosphere from models of diffusion-limited growth in non-aqueous environments

We conducted preliminary experiments designed to measure the amount of CO2 reacted from a simulated Martian atmosphere to form carbonate on silicate grains. Warm experiments at constant T (300-350 K) and with no water (vapor or liquid) yielded no detectable reaction, suggesting the following result. If we are indeed operating in the thermodynamically-favorable regime (supported by Gooding (1978) for the gas-solid reaction), then the lack of a reaction at warm temperatures suggests that a reaction in the 200-300 K regime will be less favored if reaction kinetics dominate. The completely dry scenario is thus not favored. An additional experiment, with abundant water vapor and at T approx. 300 K (constant), yielded a negative result as well. However, this is not inconsistent with Booth's findings, since lower temperatures may be required for the absorption of a monolayer of water. We plan further (lower-T) experiments.

Stephens, Stuart K.↗
NASA NTRS1992

NASA upper atmosphere research program: Research summaries, 1990 - 1991. Report to the Congress and the Environmental Protection Agency

The objectives, status, and accomplishments of the research tasks supported under the NASA Upper Atmosphere Research Program (UARP) are presented. The topics covered include the following: balloon-borne in situ measurements; balloon-borne remote measurements; ground-based measurements; aircraft-borne measurements; rocket-borne measurements; instrument development; reaction kinetics and photochemistry; spectroscopy; stratospheric dynamics and related analysis; stratospheric chemistry, analysis, and related modeling; and global chemical modeling.

Source record↗
NASA NTRS1991

Characterization of and sensor-model verification and control of the properties of PMR-13 during processing

This study presents an in situ sensor and a process-simulation model developed for monitoring and controlling the cure process of PMR-15. The time-temperature dependence of the buildup in the molecular network structure, extent of reaction, viscosity, flow, and consolidation during the cure of PMR-15 are discussed. The relationship of the time-temperature cycle used during imidization to the length of the endcapped chains formed is examined. The relationship of the time-temperature cure-processing cycle to the reaction kinetics, viscosity, flow, and consolidation during crosslinking is analyzed using frequency-dependent electromagnetic sensors and the Loos processing model. Application of the FDEMS sensing technique and the process-simulation model for quality assurance processing and automated on-line control of cure is discussed.

Kranbuehl, D.↗