Results for “Reduced order modeing” — Page 11

NASA NTRS2000

Geoscience Laser Altimeter System (GLAS) Final Test Report of DM LHP TV Testing

Two loop heat pipes (LHPs) are to be used for thermal control of the Geoscience Laser Altimeter System (GLAS), planned for flight in 2001. One LHP will be used to transport 100 W from a laser to the radiator, the other will transport 210 W from electronic boxes to the radiator. In order to verify the LHP design for the GLAS application, an LHP Development Model has been fabricated, and ambient and thermal vacuum tested. Two aluminum blocks of 15 kg and 30 kg, respectively, were attached to the LHP to simulate the thermal masses connected to the heat sources. A 20 W starter heater was installed on the evaporator to aid the loop startup. A new concept to thermally couple the vapor and liquid line was also incorporated in the LHP design. Such a thermal coupling would reduce the power requirement on the compensation chamber in order to maintain the loop set point temperature. To avoid freezing of the liquid in the condenser during cold cases, propylene was selected as the working fluid. The LHP was tested under reflux mode and with adverse elevation. Tests conducted included start-up, power cycle, steady state and transient operation during hot and cold cases, and heater power requirements for the set point temperature control of the LHP. Test results showed very successful operation of the LHP under all conditions. The 20 W starter heater proved necessary in order to start the loop when a large thermal mass was attached to the evaporator. The thermal coupling between the liquid line and the vapor line significantly reduced the heater power required for loop temperature control, which was less than 5 watts in all cases, including a cold radiator. The test also demonstrated successful operation with a propylene working fluid, with successful startups with condenser temperatures as low as 100 C. Furthermore, the test demonstrated accurate control of the loop operating temperature within +/- 0.2 C, and a successful shutdown of the loop during the survival mode of operation.

Baker, Charles↗

DOE OSTI2023

Simulation of the dynamics of gas mixtures during plasma processing in the C75 Cavity

Plasma processing using a mixture of noble gas and oxygen is a technique that is currently being used to reduce field emission and multipacting in accelerating cavities. Plasma is created inside the cavity when the gas mixture is exposed to an electromagnetic field that is generated by applying RF power through the fundamental power or higher-order mode couplers. Oxygen ions and atomic oxygen are created in the plasma which breaks down the hydrocarbons on the surface of the cavity and the residuals from this process are removed as part of the process gas flow. Removal of hydrocarbons from the surface increases the work function and reduces the secondary emission coefficient. This work describes the initial results of plasma simulation, which provides insight into the ignition process, distribution of different species, and interactions of free oxygen and oxygen ions with the cavity surfaces. The simulations have been done with an Ar/?2 plasma using COMSOL® multiphysics. These simulations help in understanding the dynamics and control of plasma inside the cavity and the exploration of different gas mixtures.

Dhakal, Pashupati↗

NASA NTRS2014

Flutter Analysis for Turbomachinery Using Volterra Series

The objective of this paper is to describe an accurate and efficient reduced order modeling method for aeroelastic (AE) analysis and for determining the flutter boundary. Without losing accuracy, we develop a reduced order model based on the Volterra series to achieve significant savings in computational cost. The aerodynamic force is provided by a high-fidelity solution from the Reynolds-averaged Navier-Stokes (RANS) equations; the structural mode shapes are determined from the finite element analysis. The fluid-structure coupling is then modeled by the state-space formulation with the structural displacement as input and the aerodynamic force as output, which in turn acts as an external force to the aeroelastic displacement equation for providing the structural deformation. NASA's rotor 67 blade is used to study its aeroelastic characteristics under the designated operating condition. First, the CFD results are validated against measured data available for the steady state condition. Then, the accuracy of the developed reduced order model is compared with the full-order solutions. Finally the aeroelastic solutions of the blade are computed and a flutter boundary is identified, suggesting that the rotor, with the material property chosen for the study, is structurally stable at the operating condition, free of encountering flutter.

computational fluid dynamics↗

DOE OSTI2024

In Situ Plasma processing of SRF cuperconducting cavities at JLAB, 2024 Update

Jefferson Lab has an ongoing R&D program in plasma processing. The experimental program investi-gated processing using argon/oxygen and heli-um/oxygen gas mixtures. Plasma processing is a com-mon technique where the free oxygen produced by the plasma breaks down and removes hydrocarbons from surfaces. This increases the work function and reduces the secondary emission coefficient. The initial focus of the effort was processing C100 cavities by injecting RF power into the high order mode (HOM) coupler ports. We also developed the methods for establishing a plasma in C75 cryomodules where the RF power is injected via the fundamental power-coupler. Four C100 cryomodules were in situ processed in the CE-BAF accelerator in May 2023 with the cryomodules returning to an operational status in Sept. 2023. The overall operational energy gain for the four cryomod-ules was 49 MeV. Methods, systems and results from processing cryomodules in the CEBAF accelerator and vertical test results are presented. Current status and future plans are discussed.

Powers, T.↗

DOE OSTI2023

IN SITU PLASMA PROCESSING OF SUPERCONDUCTING CAVITIES AT JLAB, 2023 UPDATE

Jefferson Lab has an ongoing R&D program in plasma processing which just completed a round of production processing in the CEBAF accelerator. Plasma processing is a common technique for removing hydrocarbons from surfaces, which increases the work function and reduces the secondary emission coefficient. The initial focus of the effort was processing C100 cavities by injecting RF power into the higher order mode (HOM) coupler ports. Results from processing cryomodules in the CEBAF accelerator as well as vertical test results will be present-ed. The goal of in-situ processing is to improve the operational gradients and the energy margin of the linacs. This work will describe the systems and methods used at JLAB for processing cavities using an argon-oxygen gas mixture as well as a helium-oxygen gas mixture. Before and after plasma processing results will also be presented.

Powers, Thomas↗

NASA NTRSDate not supplied

Reduced-Order Aerodynamic Modeling Based on CFD Frequency Responses from Multisine Inputs

A system identification analysis was performed to determine a reduced-order model (ROM) of a computational fluid dynamics (CFD) solver in support of linear aeroservoelastic model development and feedback control design. The approach was applied to the FUN3D code for the half-span wind tunnel test article used in the NASA-Boeing collaboration called the Integrated Adaptive Wing Technology Maturation (IAWTM) project. In a transonic flow condition, multiple inputs (11 structural mode displacements and 3 control surface deflections) were simultaneously excited with orthogonal phase-optimized multisines while multiple outputs (the corresponding 14 generalized aerodynamic forces) were recorded. From these recorded times series, the matrix of frequency responses was computed and subsequently fit using rational function approximations (RFAs). It was found that the entire (14 x 14) matrix of frequency responses could be determined from a single CFD run and that results generally followed trends predicted using other methods. Differences were attributed to the modeling fidelity and nonlinearities from structural mode and control surface interactions at higher reduced frequencies. More accurate fits of the RFAs to the frequency response data were obtained by making two CFD runs, one with only structural mode excitations and one with only control surface excitations, which reduced the degree of nonlinearity in the modeling data.

Aeroservoelasticity↗

DOE OSTI2020

Improving operational flexibility of integrated energy system with uncertain renewable generations considering thermal inertia of buildings

Insufficient flexibility in system operation caused by traditional "heat-set" operating modes of combined heat and power (CHP) units in winter heating periods is a key issue that limits renewable energy consumption. In order to reduce the curtailment of renewable energy resources through improving the operational flexibility, a novel optimal scheduling model based on chance-constrained programming (CCP), aiming at minimizing the lowest generation cost, is proposed for a small-scale integrated energy system (IES) with CHP units, thermal power units, renewable generations and representative auxiliary equipments. In this model, due to the uncertainties of renewable generations including wind turbines and photovoltaic units, the probabilistic spinning reserves are supplied in the form of chance-constrained; from the perspective of user experience, a heating load model is built with consideration of heat comfort and inertia in buildings. To solve the model, a solution approach based on sequence operation theory (SOT) is developed, where the original CCP-based scheduling model is tackled into a solvable mixed-integer linear programming (MILP) formulation by converting a chance constraint into its deterministic equivalence class, and thereby is solved via the CPLEX solver. We report the simulation results on the modified IEEE 30-bus system demonstrate that the presented method manages to improve operational flexibility of the IES with uncertain renewable generations by comprehensively leveraging thermal inertia of buildings and different kinds of auxiliary equipments, which provides a fundamental way for promoting renewable energy consumption.

30 DIRECT ENERGY CONVERSION↗

NASA NTRS1989

Flutter suppression control law synthesis for the Active Flexible Wing model

The Active Flexible Wing Project is a collaborative effort between the NASA Langley Research Center and Rockwell International. The objectives are the validation of methodologies associated with mathematical modeling, flutter suppression control law development and digital implementation of the control system for application to flexible aircraft. A flutter suppression control law synthesis for this project is described. The state-space mathematical model used for the synthesis included ten flexible modes, four control surface modes and rational function approximation of the doublet-lattice unsteady aerodynamics. The design steps involved developing the full-order optimal control laws, reducing the order of the control law, and optimizing the reduced-order control law in both the continuous and the discrete domains to minimize stochastic response. System robustness was improved using singular value constraints. An 8th order robust control law was designed to increase the symmetric flutter dynamic pressure by 100 percent. Preliminary results are provided and experiences gained are discussed.

Mukhopadhyay, Vivek↗

NASA NTRS1989

Flutter suppression control law synthesis for the active flexible wing model

The Active Flexible Wing Project is a collaborative effort between the NASA Langley Research Center and Rockwell International. The objectives are the validation of methodologies associated with mathematical modeling, flutter suppression control law development and digital implementation of the control system for application to flexible aircraft. A flutter suppression control law synthesis for this project is described. The state-space mathematical model used for the synthesis included ten flexible modes, four control surface modes and rational function approximation of the doublet-lattice unsteady aerodynamics. The design steps involved developing the full-order optimal control laws, reducing the order of the control law, and optimizing the reduced-order control law in both the continuous and the discrete domains to minimize stochastic response. System robustness was improved using singular value constraints. An 8th order robust control law was designed to increase the symmetric flutter dynamic pressure by 100 percent. Preliminary results are provided and experiences gained are discussed.

Mukhopadhyay, Vivek↗

NASA NTRS2004

Enhanced Damping for Capillary Bridge Oscillation Using Velocity Feedback

The stability of cylindrical liquid bridges in reduced gravity is affected by ambient vibrations of the spacecraft. Such vibrations are expected to excite capillary modes of the bridge. The lowest-order unstable mode is particularly susceptible to vibration as the length of the bridge approaches the stability limit. This low-order mode is known as the (2,0) mode and is an axisymmetric varicose mode of one wavelength in the axial direction. In this work, an optical system is used to detect the (2,0)-mode amplitude. The derivative of the error signal produced by this detector is used to produce the appropriate voltages on a pair of ring electrodes which are concentric with the bridge. A mode-coupled Maxwell stress profile is thus generated in proportional to the modal velocity. Depending on the sign of the gain, the damping of the capillary oscillation can be either increased or decreased. This effect has been demonstrated in Plateau-tank experiments. Increasing the damping of the capillary modes on free liquid surfaces in space could be beneficial for containerless processing and other novel technologies. [work supported by NASA]

Wei, Wei↗

NASA NTRS2004

Enhanced Damping for Capillary Bridge Oscillation Using Velocity Feedback

The stability of cylindrical liquid bridges in reduced gravity is affected by ambient vibrations of the spacecraft. Such vibrations are expected to excite capillary modes of the bridge. The lowest-order unstable mode is particularly susceptible to vibration as the length of the bridge approaches the stability limit. This low-order mode is known as the (2,0) mode and is an axisymmetric varicose mode of one wavelength in the axial direction. In this work, an optical system is used to detect the (2,0)-mode amplitude. The derivative of the error signal produced by this detector is used to produce the appropriate voltages on a pair of ring electrodes which are concentric with the bridge. A mode-coupled Maxwell stress profile is thus generated in proportional to the modal velocity. Depending on the sign of the gain, the damping of the capillary oscillation can be either increased or decreased. This effect has been demonstrated in Plateau-tank experiments. Increasing the damping of the capillary modes on free liquid surfaces in space could be beneficial for containerless processing and other novel technologies.

Wei, Wei↗

DOE OSTI2021

Data-Driven Learning for the Mori--Zwanzig Formalism: A Generalization of the Koopman Learning Framework

A theoretical framework which unifies the conventional Mori--Zwanzig formalism and the approximate Koopman learning of deterministic dynamical systems from noiseless observation is presented. In this framework, the Mori--Zwanzig formalism, developed in statistical mechanics to tackle the hard problem of construction of reduced-order dynamics for high-dimensional dynamical systems, can be considered as a natural generalization of the Koopman description of the dynamical system. We next show that, similar to the approximate Koopman learning methods, data-driven methods can be developed for the Mori--Zwanzig formalism with Mori's linear projection operator. We have developed two algorithms to extract the key operators, the Markov and the memory kernel, using time series of a reduced set of observables in a dynamical system. We have adopted the Lorenz `96 system as a test problem and solved for the above operators. These operators exhibit complex behaviors, which are unlikely to be captured by traditional modeling approaches in Mori--Zwanzig analysis. The nontrivial generalized fluctuation-dissipation relationship, which relates the memory kernel with the two-time correlation statistics of the orthogonal dynamics, was numerically verified as a validation of the solved operators. Here we present numerical evidence that the generalized Langevin equation, a key construct in the Mori--Zwanzig formalism, is more advantageous in predicting the evolution of the reduced set of observables than the conventional approximate Koopman operators.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2022

Advanced modeling and simulation of research reactors using dynamic mode decomposition

Full text of publication follows. Due to the ever-increasing safety requirements, the current trend of nuclear reactor analysis is shifting towards high-fidelity multi-physics models, which have a very high computational cost and modelling complexity. As the cost of even a single model run makes it impossible to analyse the behaviour and performance of these models on large-scale commercial plants, it has become even more significant to provide suitable benchmarks to validate and test them extensively. In this sense, research reactors offer a promising solution for the initial validation of high-fidelity models, as they are significantly smaller than commercial reactors and their characteristics are well known. In particular, the reactors of the TRIGA family have been used to assess and validate models and methods for Generation-IV designs, as they have some similar features (such as the dominance of natural convection as cooling mechanism and the difficulties in performing sub-channel analysis using standard codes). Still, the computational requirements of high-fidelity models make them unsuitable for real-time analysis, even following their assessment on research reactors. In this sense, Model Order Reduction (MOR) techniques give an additional strategy to reduce the computational cost of high-fidelity models (whilst preserving sufficient accuracy). In particular, this work focuses on Dynamic Mode Decomposition (DMD), a non-intrusive MOR technique that aims at representing models with explicit temporal dynamics by extracting the time-varying characteristics and the governing structures based only on a set of available data, thus without needing any underlying knowledge of the governing equations. In addition, DMD also computes a low-dimensional surrogate of the dynamic matrix of the system, making it suited for stability analysis and real-time evaluations. This work focuses on the application and validation of the DMD method on the Computational Fluid-Dynamics (CFD) model TRIGA Mark II reactor, also discussing in detail the potentiality of this algorithm as an advanced modelling tool for nuclear reactor analysis. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2023

Predictive machine learning approaches for the microstructural behavior of multiphase zirconium alloys

Abstract Zirconium alloys are widely used in harsh environments characterized by high temperatures, corrosivity, and radiation exposure. These alloys, which have a hexagonal closed packed (h.c.p.) structure thermo-mechanically degrade, when exposed to severe operating environments due to hydride formation. These hydrides have a different crystalline structure, than the matrix, which results in a multiphase alloy. To accurately model these materials at the relevant physical scale, it is necessary to fully characterize them based on a microstructural fingerprint, which is defined here as a combination of features that include hydride geometry, parent and hydride texture and crystalline structure of these multiphase alloys. Hence, this investigation will develop a reduced order modeling approach, where this microstructural fingerprint is used to predict critical fracture stress levels that are physically consistent with microstructural deformation and fracture modes. Machine Learning (ML) methodologies based on Gaussian Process Regression, random forests, and multilayer perceptrons (MLP) were used to predict material fracture critical stress states. MLPs, or neural networks, had the highest accuracy on held-out test sets across three predetermined strain levels of interest. Hydride orientation, grain orientation or texture, and hydride volume fraction had the greatest effect on critical fracture stress levels and had partial dependencies that were highly significant, and in comparison hydride length and hydride spacing have less effects on fracture stresses. Furthermore, these models were also used accurately predicted material response to nominal applied strains as a function of the microstructural fingerprint.

36 MATERIALS SCIENCE↗

NASA NTRS1982

Nonlocal stability analysis of the MHD Kelvin-Helmholtz instability in a compressible plasma

A general stability analysis is given of the Kevin-Helmholtz instability, for the case of sheared MHD flow of finite thickness in a compressible plasma which allows for the arbitrary orientation of the magnetic field, velocity flow, and wave vector in the plane perpendicular to the velocity gradient. The stability problem is reduced to the solution of a single second-order differential equation including a gravitational term to represent the coupling between the Kelvin-Helmholtz mode and the interchange mode. Compressibility and a magnetic field component parallel to the flow are found to be stabilizing effects, with destabilization of only the fast magnetosonic mode in the transverse case, and the presence of both Alfven and slow magnetosonic components in the parallel case. Analysis results are used in a discussion of the stability of sheared plasma flow at the magnetopause boundary and in the solar wind.

Miura, A.↗

NASA NTRS1986

Aeroelastic control of oblique-wing aircraft

The U.S. Navy and NASA are currently involved in the design and development of an unsymmetric-skew-wing aircraft capable of 65 deg wing sweep and flight at Mach 1.6. A generic skew-wing aircraft model was developed for 45 deg wing skew at a flight condition of Mach 0.70 and 3048 m altitude. At this flight condition the aircraft has a wing flutter mode. An active implementable control law was developed using the linear quadratic Gaussian design technique. A method of modal residualization was used to reduce the order of the controller used for flutter suppression.

Burken, J. J.↗

NASA NTRS1986

The effect of a small initial curvature on the free vibration of clamped, rectangular plates

An analytical method of obtaining the natural frequencies and mode shapes of clamped, rectangular plates having a small initial curvature is presented. Specifically, the singular perturbation technique is used to reduce the fourth-order plate vibration problem to the simpler membrane problem with modified boundary conditions that account for the bending effects. The eigenfrequencies for plates with inverse aspect ratios varying between 0.1 and 1.0 and for the dimensionless normal prestress between 0.1 and 1.0 have been presented for values of epsilon, the normalized bending rigidity, ranging between 0.0010 and 0.2500. It is established that a small initial curvature has no effect on the frequency of vibration of the plate. However, its effect is manifested in the eigenmodes.

Adeniji-Fashola, A. A.↗

NASA NTRS1986

Aeroelastic control of oblique-wing aircraft

The U.S. Navy and NASA are currently involved in the design and development of an unsymmetric-skew-wing aircraft capable of 65 deg wing sweep and flight at Mach 1.6. A generic skew-wing aircraft model was developed for 45 deg wing skew at a flight condition of Mach 0.70 and 3048 m altitude. At this flight condition the aircraft has a wing flutter mode. An active implementable control law was developed using the linear quadratic Gaussian design technique. A method of modal residualization was used to reduce the order of the controller used for flutter suppression.

Burken, J. J.↗