Results for “Reliability Engineering” — Page 11

NASA NTRS1979

Engineering Area Investigation of Reliability Attributes and Accelerated Stress Factors on Terrestrial Solar Cells

Results obtained include the definition of a simplified stress test schedule for terrestrial solar cells based on the work performed during the first program year, and the design and fabrication of improved jigs and fixtures for electrical measurement and stress testing. Implementation of these advanced techniques for accelerated stress testing is underway on three solar cell types. In addition, review of the literature on second quadrant phenomena was begun and some preliminary second-quadrant electrical measurements were performed. Results obtained at the first down time for 75 C B-T testing and biased and unbiased T-H pressure cooker testing of type F cells showed little or no degradation in electrical parameters. Significant physical effects (large solder bubbles) were noted for type F cells subjected to the pressure cooker stress test.

Lathrop, J. W.↗

NASA NTRS2001

Flow Range of Centrifugal Compressor Being Extended

General Aviation will benefit from turbine engines that are both fuel-efficient and reliable. Current engines fall short of their potential to achieve these attributes. The reason is compressor surge, which is a flow stability problem that develops when the compressor is subjected to conditions that are outside of its operating range. Compressor surge can occur when fuel flow to the engine is increased, temporarily back pressuring the compressor and pushing it past its stability limit, or when the compressor is subjected to inlet flow-field distortions that may occur during takeoff and landing. Compressor surge can result in the loss of an aircraft. As a result, engine designers include a margin of safety between the operating line of the engine and the stability limit line of the compressor. Unfortunately, the most efficient operating line for the compressor is usually closer to its stability limit line than it is to the line that provides an adequate margin of safety. A wider stable flow range will permit operation along the most efficient operating line of the compressor, improving the specific fuel consumption of the engine and reducing emissions. The NASA Glenn Research Center is working to extend the stable flow range of the compressor. Significant extension has been achieved in axial compressors by injecting air upstream of the compressor blade rows. Recently, the technique was successfully applied to a 4:1 pressure ratio centrifugal compressor by injecting streams of air into the diffuser. Both steady and controlled unsteady injection were used to inject air through the diffuser shroud surface and extend the range. Future work will evaluate the effect of air injection through the diffuser hub surface and diffuser vanes with the goal of maximizing the range extension while minimizing the amount of injected air that is required.

Skoch, Gary J.↗

NASA NTRS2018

Thermal Modeling of an Advanced Geared Turbofan for Distributed Engine Control Application

Reliability and life-expectancy of gas turbine engine components is very much correlated to the temperature environment in which they operate. This is no different for control system components, especially those with electronic parts. In recent years, the concept of Distributed Engine Control (DEC) has emerged to address the limitations of the current centralized control implementation. This new approach involves relocating control system components from a relatively benign environment to the harsher thermal environment of the engine casing and its surrounding structures and cavities. In this paper, an approach to modeling the gas turbine thermal environment is described. The modeling approach is applied to a 3rd generation geared turbofan design with a focus on the engine locations where control instrumentation and actuation could be installed. The analysis was conducted with an eye toward component reliability and service life as it relates to the thermal environment. The results were found to be reasonable. Furthermore, the model is shown to execute in real-time within a multi-model simulation environment that demonstrates the capability to interact with hardware to drive test equipment.

Kratz, Jonathan↗

NASA NTRS1989

Stratified charge rotary engine combustion studies

Analytical and experimental studies of the combustion process in a stratified charge rotary engine (SCRE) continue to be the subject of active research in recent years. Specifically to meet the demand for more sophisticated products, a detailed understanding of the engine system of interest is warranted. With this in mind the objective of this work is to develop an understanding of the controlling factors that affect the SCRE combustion process so that an efficient power dense rotary engine can be designed. The influence of the induction-exhaust systems and the rotor geometry are believed to have a significant effect on combustion chamber flow characteristics. In this report, emphasis is centered on Laser Doppler Velocimetry (LDV) measurements and on qualitative flow visualizations in the combustion chamber of the motored rotary engine assembly. This will provide a basic understanding of the flow process in the RCE and serve as a data base for verification of numerical simulations. Understanding fuel injection provisions is also important to the successful operation of the stratified charge rotary engine. Toward this end, flow visualizations depicting the development of high speed, high pressure fuel jets are described. Friction is an important consideration in an engine from the standpoint of lost work, durability and reliability. MSU Engine Research Laboratory efforts in accessing the frictional losses associated with the rotary engine are described. This includes work which describes losses in bearing, seal and auxillary components. Finally, a computer controlled mapping system under development is described. This system can be used to map shapes such as combustion chamber, intake manifolds or turbine blades accurately.

Shock, H.↗

NASA NTRS2010

NASA Puffin Electric Tailsitter VTOL Concept

Electric propulsion offers dramatic new vehicle mission capabilities, not possible with turbine or reciprocating engines; including high reliability and efficiency, low engine weight and maintenance, low cooling drag and volume required, very low noise and vibration, and zero emissions. The only penalizing characteristic of electric propulsion is the current energy storage technology level, which is set to triple over the next 5-10 years through huge new investments in this field. Most importantly, electric propulsion offers incredible new degrees of freedom in aircraft system integration to achieve unprecedented levels of aerodynamic, propulsive, control, and structural synergistic coupling. A unique characteristic of electric propulsion is that the technology is nearly scale-free, permitting small motors to be parallelized for fail-safe redundancy, or distributed across the airframe for tightly coupled interdisciplinary functionality without significant impacts in motor-controller efficiency or specific weight. Maximizing the potential benefit of electric propulsion is dependent on applying this technology to synergistic mission concepts. The vehicle missions with the most benefit include those which constrain environmental impact (or limit noise, exhaust, or emission signatures) are short range, or where large differences exist in the propulsion system sizing between takeoff and cruise conditions. Electric propulsion offers the following unique capabilities that other propulsion systems can t provide for short range Vertical Takeoff and Landing (VTOL) aircraft; elimination of engine noise and emissions, drastic reduction in engine cooling and radiated heat, drastic reduction in vehicle vibration levels, drastic improvement in reliability and operating costs, variable speed output at full power, for improved cruise efficiency at low tip-speed, elimination of high/hot sizing penalty, and reduction of engine-out penalties.

Moore, Mark D.↗

NASA NTRS2010

A History of Welding on the Space Shuttle Main Engine (1975 to 2010)

The Space Shuttle Main Engine (SSME) is a high performance, throttleable, liquid hydrogen fueled rocket engine. High thrust and specific impulse (Isp) are achieved through a staged combustion engine cycle, combined with high combustion pressure (approx.3000psi) generated by the two-stage pump and combustion process. The SSME is continuously throttleable from 67% to 109% of design thrust level. The design criteria for this engine maximize performance and weight, resulting in a 7,800 pound rocket engine that produces over a half million pounds of thrust in vacuum with a specific impulse of 452/sec. It is the most reliable rocket engine in the world, accumulating over one million seconds of hot-fire time and achieving 100% flight success in the Space Shuttle program. A rocket engine with the unique combination of high reliability, performance, and reusability comes at the expense of manufacturing simplicity. Several innovative design features and fabrication techniques are unique to this engine. This is as true for welding as any other manufacturing process. For many of the weld joints it seemed mean cheating physics and metallurgy to meet the requirements. This paper will present a history of the welding used to produce the world s highest performance throttleable rocket engine.

Zimmerman, Frank R.↗

NASA NTRS2003

Use of Soft Computing Technologies For Rocket Engine Control

The problem to be addressed in this paper is to explore how the use of Soft Computing Technologies (SCT) could be employed to further improve overall engine system reliability and performance. Specifically, this will be presented by enhancing rocket engine control and engine health management (EHM) using SCT coupled with conventional control technologies, and sound software engineering practices used in Marshall s Flight Software Group. The principle goals are to improve software management, software development time and maintenance, processor execution, fault tolerance and mitigation, and nonlinear control in power level transitions. The intent is not to discuss any shortcomings of existing engine control and EHM methodologies, but to provide alternative design choices for control, EHM, implementation, performance, and sustaining engineering. The approaches outlined in this paper will require knowledge in the fields of rocket engine propulsion, software engineering for embedded systems, and soft computing technologies (i.e., neural networks, fuzzy logic, and Bayesian belief networks), much of which is presented in this paper. The first targeted demonstration rocket engine platform is the MC-1 (formerly FASTRAC Engine) which is simulated with hardware and software in the Marshall Avionics & Software Testbed laboratory that

Trevino, Luis C.↗

NASA NTRS2016

Digital Image Correlation Techniques Applied to Large Scale Rocket Engine Testing

Rocket engine hot-fire ground testing is necessary to understand component performance, reliability and engine system interactions during development. The J-2X upper stage engine completed a series of developmental hot-fire tests that derived performance of the engine and components, validated analytical models and provided the necessary data to identify where design changes, process improvements and technology development were needed. The J-2X development engines were heavily instrumented to provide the data necessary to support these activities which enabled the team to investigate any anomalies experienced during the test program. This paper describes the development of an optical digital image correlation technique to augment the data provided by traditional strain gauges which are prone to debonding at elevated temperatures and limited to localized measurements. The feasibility of this optical measurement system was demonstrated during full scale hot-fire testing of J-2X, during which a digital image correlation system, incorporating a pair of high speed cameras to measure three-dimensional, real-time displacements and strains was installed and operated under the extreme environments present on the test stand. The camera and facility setup, pre-test calibrations, data collection, hot-fire test data collection and post-test analysis and results are presented in this paper.

Gradl, Paul R.↗

NASA NTRS1997

Multi-Disciplinary System Reliability Analysis

The objective of this study is to develop a new methodology for estimating the reliability of engineering systems that encompass multiple disciplines. The methodology is formulated in the context of the NESSUS probabilistic structural analysis code developed under the leadership of NASA Lewis Research Center. The NESSUS code has been successfully applied to the reliability estimation of a variety of structural engineering systems. This study examines whether the features of NESSUS could be used to investigate the reliability of systems in other disciplines such as heat transfer, fluid mechanics, electrical circuits etc., without considerable programming effort specific to each discipline. In this study, the mechanical equivalence between system behavior models in different disciplines are investigated to achieve this objective. A new methodology is presented for the analysis of heat transfer, fluid flow, and electrical circuit problems using the structural analysis routines within NESSUS, by utilizing the equivalence between the computational quantities in different disciplines. This technique is integrated with the fast probability integration and system reliability techniques within the NESSUS code, to successfully compute the system reliability of multi-disciplinary systems. Traditional as well as progressive failure analysis methods for system reliability estimation are demonstrated, through a numerical example of a heat exchanger system involving failure modes in structural, heat transfer and fluid flow disciplines.

Mahadevan, Sankaran↗

NASA NTRS2001

Multidisciplinary System Reliability Analysis

The objective of this study is to develop a new methodology for estimating the reliability of engineering systems that encompass multiple disciplines. The methodology is formulated in the context of the NESSUS probabilistic structural analysis code, developed under the leadership of NASA Glenn Research Center. The NESSUS code has been successfully applied to the reliability estimation of a variety of structural engineering systems. This study examines whether the features of NESSUS could be used to investigate the reliability of systems in other disciplines such as heat transfer, fluid mechanics, electrical circuits etc., without considerable programming effort specific to each discipline. In this study, the mechanical equivalence between system behavior models in different disciplines are investigated to achieve this objective. A new methodology is presented for the analysis of heat transfer, fluid flow, and electrical circuit problems using the structural analysis routines within NESSUS, by utilizing the equivalence between the computational quantities in different disciplines. This technique is integrated with the fast probability integration and system reliability techniques within the NESSUS code, to successfully compute the system reliability of multidisciplinary systems. Traditional as well as progressive failure analysis methods for system reliability estimation are demonstrated, through a numerical example of a heat exchanger system involving failure modes in structural, heat transfer and fluid flow disciplines.

Mahadevan, Sankaran↗

NASA NTRS2016

Applicability and Limitations of Reliability Allocation Methods

Reliability allocation process may be described as the process of assigning reliability requirements to individual components within a system to attain the specified system reliability. For large systems, the allocation process is often performed at different stages of system design. The allocation process often begins at the conceptual stage. As the system design develops, more information about components and the operating environment becomes available, different allocation methods can be considered. Reliability allocation methods are usually divided into two categories: weighting factors and optimal reliability allocation. When properly applied, these methods can produce reasonable approximations. Reliability allocation techniques have limitations and implied assumptions that need to be understood by system engineers. Applying reliability allocation techniques without understanding their limitations and assumptions can produce unrealistic results. This report addresses weighting factors, optimal reliability allocation techniques, and identifies the applicability and limitations of each reliability allocation technique.

Reliability allocation↗

NASA NTRSDate not supplied

Assessing Engine Hot Fire Data for Human Spaceflight Applications

Development and certification of liquid engine systems for human spaceflight missions requires exhaustive analysis to meet the NASA’s requirements for engine health, reliability, and performance. The techniques used to assess requirement conformance and test-to-test engine health pose many unique challenges including the unusually large scale of data, complex component and system analysis, and rigorous engineering judgement standards. To address these challenges, NASA Marshall Space Flight Center’s Engine Systems branch has developed and maintained a robust software suite and operational processes that satisfy programmatic requirements levied on engines and the 7 Elements of Flight Rationale. Analysis at a systems level includes subsystem assessment of components such as turbomachinery and combustion devices as well as structural and fluid dynamics and transient and steady-state assessment at a systems level. Some of the most important tools to accomplish this analysis are automated script databases, creation of historical and statistical comparisons, and parameters calculated at the full data rate. These tools greatly simplify the crucial processes of anomaly investigation, limit monitoring, health assessment, and timely communication of key conclusions drawn from hot fire testing and flight data analysis.

Data Assessment↗

NASA NTRSDate not supplied

Assessing Engine Hot Fire Data for Human Spaceflight Applications

Development and certification of liquid engine systems for human spaceflight missions requires exhaustive analysis to meet the NASA’s requirements for engine health, reliability, and performance. The techniques used to assess requirement conformance and test-to-test engine health pose many unique challenges including the unusually large scale of data, complex component and system analysis, and rigorous engineering judgement standards. To address these challenges, NASA Marshall Space Flight Center’s Engine Systems branch has developed and maintained a robust software suite and operational processes that satisfy programmatic requirements levied on engines and the 7 Elements of Flight Rationale. Analysis at a systems level includes subsystem assessment of components such as turbomachinery and combustion devices as well as structural and fluid dynamics and transient and steady-state assessment at a systems level. Some of the most important tools to accomplish this analysis are automated script databases, creation of historical and statistical comparisons, and parameters calculated at the full data rate. These tools greatly simplify the crucial processes of anomaly investigation, limit monitoring, health assessment, and timely communication of key conclusions drawn from hot fire testing and flight data analysis.

Data Assessment↗

NASA NTRSDate not supplied

Assessing Hot Fire Data with WinPlot

Development and certification of liquid engine systems for human spaceflight missions requires exhaustive analysis to meet the NASA’s requirements for engine health, reliability, and performance. The techniques used to assess requirement conformance and test-to-test engine health and performance pose many unique challenges including the unusually large scale of data, complex component and system analysis, and rigorous engineering judgement standards. To address these challenges, NASA Marshall Space Flight Center’s Engine Systems branch has developed and maintained a robust software suite and operational processes that satisfy programmatic requirements levied on engines and the 7 Elements of Flight Rationale. Analysis at a systems level includes subsystem assessment of components such as turbomachinery and combustion devices as well as structural and fluid dynamics and transient and steady-state assessment at a systems level. Some of the most important tools to accomplish this analysis are automated script databases, creation of historical and statistical comparisons, and parameters calculated at the full data rate. These tools greatly simplify the crucial processes of anomaly investigation, limit monitoring, health assessment, and timely communication of key conclusions drawn from hot fire testing and flight data analysis.

J. Davis Hunter↗

NASA NTRS2017

NASA Collaborative Design Processes

This is Block 1, the first evolution of the world's most powerful and versatile rocket, the Space Launch System, built to return humans to the area around the moon. Eventually, larger and even more powerful and capable configurations will take astronauts and cargo to Mars. On the sides of the rocket are the twin solid rocket boosters that provide more than 75 percent during liftoff and burn for about two minutes, after which they are jettisoned, lightening the load for the rest of the space flight. Four RS-25 main engines provide thrust for the first stage of the rocket. These are the world's most reliable rocket engines. The core stage is the main body of the rocket and houses the fuel for the RS-25 engines, liquid hydrogen and liquid oxygen, and the avionics, or "brain" of the rocket. The core stage is all new and being manufactured at NASA's "rocket factory," Michoud Assembly Facility near New Orleans. The Launch Vehicle Stage Adapter, or LVSA, connects the core stage to the Interim Cryogenic Propulsion Stage. The Interim Cryogenic Propulsion Stage, or ICPS, uses one RL-10 rocket engine and will propel the Orion spacecraft on its deep-space journey after first-stage separation. Finally, the Orion human-rated spacecraft sits atop the massive Saturn V-sized launch vehicle. Managed out of Johnson Space Center in Houston, Orion is the first spacecraft in history capable of taking humans to multiple destinations within deep space. 2) Each element of the SLS utilizes collaborative design processes to achieve the incredible goal of sending human into deep space. Early phases are focused on feasibility and requirements development. Later phases are focused on detailed design, testing, and operations. There are 4 basic phases typically found in each phase of development.

Jones, Davey↗

NASA NTRSDate not supplied

Surface Instability of Liquid Propellants in Microgravity During Pulsed Settling Operations

Pulsing reaction control system (RCS) thrusters, vent valves, or other propulsion devices can preserve propellant resources in space, but this operation also effectively introduces a vibration to the vehicle. When the vibration is perpendicular to the liquid propellant surface, Faraday waves may be generated at the liquid-vapor interface. These Faraday instabilities can perturb or break up the liquid surface of cryogenic tanks, leading to inefficiencies in thermal management or even ullage collapse. Drawing from theory and experiments, an engineering model defining the allowable design regions for pulsed settling in microgravity was assembled and verified with computational fluid dynamics (CFD) simulations. A traditional settling metric, the Bond number, was also overlaid in the model to indicate which duty cycles were insufficient to overcome surface tension and aggregate propellant. Mission planners and engineers can consult the tool to rapidly evaluate the stability of a liquid-vapor interface given the pulse frequency and the excitation acceleration. Expressions developed for Faraday waves induced by a sinusoidal forcing input at standard gravity were found to provide excellent predictive capabilities for pulsed, or rectangular, waveforms in the absence of a consistent gravitational acceleration. This study extends the usage of these equations to an alternative forcing function and microgravity environments for the purpose of estimating natural frequencies, surface mode shapes, surface wave amplitudes, and the onset of droplet ejection. CFD simulations with the Loci/STREAM-VoF (Volume of Fluid) solver were initially validated against experimental results in standard gravity. Discrete points on the design map were then investigated with CFD and confirmed that the engineering model reliably indicates surface stability and most Faraday wave characteristics without requiring higher-fidelity tools. The engineering model is highly extensible and can be adapted for various propellant fill fractions, fluid properties, and tank sizes.

Faraday Waves↗

NASA NTRSDate not supplied

Surface Instability of Liquid Propellants in Microgravity During Pulsed Settling Operations

Pulsing reaction control system (RCS) thrusters, vent valves, or other propulsion devices can preserve propellant resources in space, but this operation also effectively introduces a vibration to the vehicle. When the vibration is perpendicular to the liquid propellant surface, Faraday waves may be generated at the liquid-vapor interface. These Faraday instabilities can perturb or break up the liquid surface of cryogenic tanks, leading to inefficiencies in thermal management or even ullage collapse. Drawing from theory and experiments, an engineering model defining the allowable design regions for pulsed settling in microgravity was assembled and verified with computational fluid dynamics (CFD) simulations. A traditional settling metric, the Bond number, was also overlaid in the model to indicate which duty cycles were insufficient to overcome surface tension and aggregate propellant. Mission planners and engineers can consult the tool to rapidly evaluate the stability of a liquid-vapor interface given the pulse frequency and the excitation acceleration. Expressions developed for Faraday waves induced by a sinusoidal forcing input at standard gravity were found to provide excellent predictive capabilities for pulsed, or rectangular, waveforms in the absence of a consistent gravitational acceleration. This study extends the usage of these equations to an alternative forcing function and microgravity environments for the purpose of estimating natural frequencies, surface mode shapes, surface wave amplitudes, and the onset of droplet ejection. CFD simulations with the Loci/STREAM-VoF (Volume of Fluid) solver were initially validated against experimental results in standard gravity. Discrete points on the design map were then investigated with CFD and confirmed that the engineering model reliably indicates surface stability and most Faraday wave characteristics without requiring higher-fidelity tools. The engineering model is highly extensible and can be adapted for various propellant fill fractions, fluid properties, and tank sizes.

Faraday Waves↗

NASA NTRS1966

Special tooling for joining tubing in place

The Saturn S-II stage and the Apollo spacecraft will include in their design and construction various pressurized tubing systems that will encounter service temperatures of 280° F to -423° F. Design engineering and reliability requirements and weight restrict ions have dictated new concepts to assure leak-tight joints for rocket engine fuel lines, pressurization systems, utility systems, and hydraulic systems. An investigation was initiated at North American Aviation, Inc., Space and Information Systems Division, utilizing the in-place automatically controlled miniaturized fusion-welding equipment originally developed by the Los Angeles Division of NAA and modified to meet the needs of Apollo and Saturn welded tubular systems. The objective was to make circumferential flanged weld joints in any position in 304L stainless for Saturn S-II and sleeve-type joints in 304L for Apollo. Inconel X, commercially pure titanium, 5052-0 aluminum, and 6061 T6 aluminum were also tested experimentally. Extensive environmental, static, and dynamic testing programs were conducted to determine the as-welded mechanical properties, design allowables, and reliability for the tube joints. This paper discusses both the experimental and production phases. Subsequently, the new tube welding process was approved and incorporated into manufacturing fabrication methods for tube joining.

Saturn S-II stage↗