SEARCH · Search NASA

Results for “Rotor Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Effects of ingested atmospheric turbulence on measured tail rotor acoustics

Results from an outdoor hover test of a full-scale Lynx tail rotor are presented. The investigation was designed to further the understanding of the acoustics of an isolated tail rotor hovering out-of-ground effect in atmospheric turbulence, without the effects of the main rotor wake or other helicopter components. Measurements include simultaneous rotor performance, noise, inflow, and far-field atmospheric turbulence. Results with grid-generated inflow turbulence are also presented. The effects of turbulence ingestion on rotor noise are quantified. Turbulence ingestion noise is found to be the dominant noise mechanism at locations near the rotor axis. At these locations, the sound radiated by the hovering rotor increases with both increasing atmospheric wind speed and ingested rms turbulent velocity.

Signor, David B.↗

NASA NTRS2019

Correlation of Full-Scale Isolated Proprotor Performance and Loads

A full-scale isolated proprotor test was recently conducted in the USAF National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center. The test article was a 3-bladed research rotor derived from the right-hand rotor of the AW609. For this test, the NASA Tiltrotor Test Rig (TTR) and rotor were installed in the 40- by 80-foot test section. This paper presents correlations between data and predictions of rotor performance and blade moments using the newly acquired test data and the comprehensive analysis CAMRAD II. The operational conditions covered in this analytical study are: hover (actually, low speed vertical climb), cruise (airplane mode), conversion, and helicopter mode. Mean and 1/2 peak-to-peak quantities (hpp) are correlated; time-history correlation for the helicopter condition is also included. The correlation is reasonable to good. Also, the hover calculations turned out to be useful in providing reality checks on the test hardware such as: a) the functioning of the blade strain gages and b) calibration of the measurement of the collective pitch hardware. The time-history correlation shows that, compared to the rolled-up wake model, the multiple-trailer wake model improves the correlation slightly; the longitudinal cyclic correlation is reasonable but the lateral cyclic correlation is not good, and the collective is predicted well by the rolled-up wake model; the flap moment correlation is reasonable; the pitch link load and lag moment are underpredicted; and the torsion moment correlation is poor and needs further study.

Kottapalli, Sesi↗

NASA NTRS1994

Measurements of atmospheric turbulence effects on tail rotor acoustics

Results from an outdoor hover test of a full-scale Lynx tail rotor are presented. The investigation was designed to further the understanding of the acoustics of an isolated tail rotor hovering out-of-ground effect in atmospheric turbulence, without the effects of the main rotor wake or other helicopter components. Measurements include simultaneous rotor performance, noise, inflow, and far-field atmospheric turbulence. Results with grid-generated inflow turbulence are also presented. The effects of atmospheric turbulence ingestion on rotor noise are quantified. In contradiction to current theories, increasing rotor inflow and rotor thrust were found to increase turbulence ingestion noise. This is the final report of Task 13A--Helicopter Tail Rotor Noise, of the NASA/United Kingdom Defense Research Agency cooperative Aeronautics Research Program.

Hagen, Martin J.↗

NASA NTRS1978

Rotor-airfoil flight investigation - Preliminary results

A flight investigation has been conducted to study the behavior of three advanced-technology airfoils in the three-dimensional, unsteady-flow environment of the helicopter main rotor. Three sets of instrumented main-rotor blades were flown on an AH-1G helicopter. Each set employed one of three airfoils developed with significantly different design technologies. Data are given on performance, rotor loads, and the measurements of chordwise pressure distribution at 90 percent blade radius. The pressure data are compared with theoretical distributions calculated for two-dimensional, steady flow.

Morris, C. E. K., Jr.↗

NASA NTRS1984

Hover test of a full-scale hingeless helicopter rotor: Aeroelastic stability, performance and loads data

A hover test of a full-scale, hingeless rotor system was conducted in the NASA Ames 40- by 80-foot wind tunnel. The rotor was tested on the Ames rotor test apparatus. Rotor aeroelastic stability, performance, and loads at various rotational speeds and thrust coefficients were investigated. The primary objective was to determine the inplane stability characteristics of the rotor system. Rotor inplane damping data were obtained for operation between 350 and 425 rpm (design speed), and for thurst coefficients between 0.0 and 0.12. The rotor was stable for all conditions tested. At constant rotor rotational speed, a minimum inplane dampling level was obtained at a thrust coefficient approximately = 0.02. At constant rotor lift, a minimum in rotor inplane damping was measured at 400 rpm.

Peterson, R. L.↗

NASA NTRS1980

A comprehensive analytical model of rotorcraft aerodynamics and dynamics. Part 1: Analysis development

Structural, inertia, and aerodynamic models were combined to form a comprehensive model of rotor aerodynamics and dynamics that is applicable to a wide range of problems and a wide class of vehicles. A digital computer program is used to calculate rotor performance, loads, and noise; helicopter vibration and gust response; flight dynamics and handling qualities; and system aeroelastic stability. The analysis is intended for use in the design, testing, and evaluation of rotors and rotorcraft, and to be a basis for further development of rotary wing theories.

Johnson, W.↗

NASA NTRS2004

Evaluation of CFD to Determine Two-Dimensional Airfoil Characteristics for Rotorcraft Applications

The efficient prediction of helicopter rotor performance, vibratory loads, and aeroelastic properties still relies heavily on the use of comprehensive analysis codes by the rotorcraft industry. These comprehensive codes utilize look-up tables to provide two-dimensional aerodynamic characteristics. Typically these tables are comprised of a combination of wind tunnel data, empirical data and numerical analyses. The potential to rely more heavily on numerical computations based on Computational Fluid Dynamics (CFD) simulations has become more of a reality with the advent of faster computers and more sophisticated physical models. The ability of five different CFD codes applied independently to predict the lift, drag and pitching moments of rotor airfoils is examined for the SC1095 airfoil, which is utilized in the UH-60A main rotor. Extensive comparisons with the results of ten wind tunnel tests are performed. These CFD computations are found to be as good as experimental data in predicting many of the aerodynamic performance characteristics. Four turbulence models were examined (Baldwin-Lomax, Spalart-Allmaras, Menter SST, and k-omega).

Smith, Marilyn J.↗

NASA NTRS1984

Analysis of axisymmetric body effects on rotor aerodynamics using modified slender body theory

A modified slender body theory was used in modelling the flowfield around an axisymmetric body at zero angle of attack. The model was defined in an attempt to characterize body-induced effects on helicopter rotor performance and loading using efficient computation methods. The streamfunction for an axial source distribution was applied in the body model, which was then adapted to the helicopter analysis code (CAMRAD). The body-induced velocities were calculated for separate locations on the rotor disk. Three different rotor models in nonuniform inflow with a free wake geometry were considered. Comparison of predictions with data on ellipsoidal and axisymmetric bodies showed good agreement for moderately thick ellipsoidal bodies. Oscillatory blade bending moments were increased by the presence of the body, but overall performance impact was negligible. Computational efficiency was 10-20 percent better than with a potential flow panel code.

Yamauchi, G. K.↗

NASA NTRS1981

Development of a comprehensive analysis for rotorcraft. I - Rotor model and wake analysis

The development of a comprehensive analytical model of rotorcraft aerodynamics and dynamics is described. Particular emphasis is given to describing the reasons behind the choices and decisions involved in constructing the model. The analysis is designed to calculate rotor performance, loads and noise; helicopter vibration and gust response; flight dynamics and handling qualities; and system aeroelastic stability. It is intended for use in the design, testing and evaluation of a wide class of rotors and rotorcraft, and to be the basis for further development of rotary wing theories. The general characteristics of the geometric, structural, inertial, and aerodynamic models used for the rotorcraft components are described, including the assumptions introduced by the chosen models and the resulting capabilities and limitations. Finally, some examples from recent applications of the analysis are given.

Johnson, W.↗

NASA NTRS1981

Development of a comprehensive analysis for rotorcraft. II - Aircraft model, solution procedure and applications

The development of a comprehensive analytical model of rotorcraft aerodynamics and dynamics is described. Particular emphasis is given to describing the reasons behind the choices and decisions involved in constructing the model. The analysis is designed to calculate rotor performance, loads and noise; helicopter vibration and gust response; flight dynamics and handling qualities; and system aeroelastic stability. It is intended for use in the design, testing and evaluation of a wide class of rotors and rotorcraft and to be the basis for further development of rotary wing theories. The general characteristics of the geometric, structural, inertial and aerodynamic models used for the rotorcraft components are described, including the assumptions introduced by the chosen models and the resulting capabilities and limitations. Finally, some examples from recent applications of the analysis are given.

Johnson, W.↗

NASA NTRS1976

A note on correlation description

The paper suggests some modifications to definitions of correlation functions made by Freeman and Bennett (1974) specifically for comparing measured quantities with those predicted by rotor theories, with reference to rotorcraft flight simulation. Special attention is paid to the quality of correlation, determined by a quality factor relating the measured and computed entities. Correlation criteria (mean load and rotor performance, overall amplitude and phase, harmonic altitude and harmonic phase) are examined, along with phase angle correlation criteria (harmonic phase defined by sine-cosine relation and harmonic phase defined by a first positive peak rotor azimuth position)

Mccloud, J. L., III↗

NASA NTRS2001

Rotor Broadband Noise Prediction with Comparison to Model Data

This paper reports an analysis and prediction development of rotor broadband noise. The two primary components of this noise are Blade-Wake Interaction (BWI) noise, due to the blades' interaction with the turbulent wakes of the preceding blades, and "Self" noise, due to the development and shedding of turbulence within the blades' boundary layers. Emphasized in this report is the new code development for Self noise. The analysis and validation employs data from the HART program, a model BO-105 rotor wind tunnel test conducted in the German-Dutch Wind Tunnel (DNW). The BWI noise predictions are based on measured pressure response coherence functions using cross-spectral methods. The Self noise predictions are based on previously reported semiempirical modeling of Self noise obtained from isolated airfoil sections and the use of CAMRAD.Modl to define rotor performance and local blade segment flow conditions. Both BWI and Self noise from individual blade segments are Doppler shifted and summed at the observer positions. Prediction comparisons with measurements show good agreement for a range of rotor operating conditions from climb to steep descent. The broadband noise predictions, along with those of harmonic and impulsive Blade-Vortex Interaction (BVI) noise predictions, demonstrate a significant advance in predictive capability for main rotor noise.

Brooks, Thomas F.↗

NASA NTRS1985

Performance degradation of helicopter rotor in forward flight due to ice

This study addresses the analytical assessment of the degradation in the forward flight performance of the front rotor Boeing Vertol CH47D helicopter in a rime ice natural icing encounter. The front rotor disk was divided into 24 15-deg sections and the local Mach number and angle of attack were evaluated as a function of azimuthal and radial location for a specified flight condition. Profile drag increments were then calculated as a function of azimuthal and radial position for different times of exposure to icing, and the rotor performance was re-evaluated including these drag increments. The results of the analytical prediction method, such as horsepower required to maintain a specific flight condition, as a function of icing time have been generated. The method to illustrate the value of such an approach in assessing performance changes experienced by a helicopter rotor as a result of rime ice accretion is described.

Korkan, K. D.↗

NASA NTRS1975

Rotorcraft low-speed download drag definition and its reduction

Download drag for rotorcraft in hover and low-speed flight is a burden which significantly affects useful load, fuel, and payload. Reduction of the burden will enhance these aspects of rotorcraft and complement the forthcoming improvements in isolated rotor performance. Analyses and experimental data are available, though fragmentary, regarding gross drag, thrust recovery, and other characteristics which can be utilized to define interim rotorcraft design changes to reduce the burden. Eventually the experimental data and a comprehensive combination of rotor, rotor-wake, and potential-flow analyses can evolve to reduce the burden to an absolute minimum.

Wilson, J. C.↗

NASA NTRS1988

The development of CFD methods for rotor applications

The optimum design of the advancing helicopter rotor for high-speed forward flight always involves a tradeoff between transonic and stall limitations. However, the preoccupation of the rotor industry was primarily concerned with stall until well into the 1970s. This emphasis on stall resulted from the prevalent use of low-solidity rotors with rather outdated airfoil sections. The use of cambered airfoil sections and higher-solidity rotors substantially reduced stall and revealed the advancing transonic flow to be a more persistent limitation to high-speed rotor performance. Work in this area was spurred not only by operational necessity but also by the development of a tool for the prediction of these flows (the method of computational fluid dynamics). The development of computational fluid dynamics for these rotor problems was a major Army and NASA achievement. This work is now being extended to other rotor flow problems. The developments are outlined.

Caradonna, F. X.↗

NASA NTRSDate not supplied

Quantitative Approach for the Accurate CFD Simulation of Hover in Turbulent Flow

Time-dependent Navier-Stokes simulations have been carried out for a V22 rotor in hover using an improved, low-diffusion, HLLE++ upwind algorithm in the OVERFLOW code. Emphasis is placed on lessons learned over the past decade regarding the effects of high-order spatial accuracy, grid resolution, and the use of detached eddy simulation in predicting the rotor performance, i.e., figure-of-merit (FM). A quick-start procedure is described together with a statistical measure of FM convergence that reduces hover computations by 5 times, similar in computational work for forward flight. Furthermore, Cartesian adaptive mesh refinement in the rotor wake revealed a complex turbulent flow with worm-like structures of various scales. These turbulent worms, found computationally more than a decade ago, have recently been observed in a separate German Aerospace Center (DLR) experiment. Moreover, adaptive mesh refinement has been used to resolve the tip-vortex to its correct physical size.

Neal M. Chaderjian↗

NASA NTRS1987

Design and performance of controlled-diffusion stator compared with original double-circular-arc stator

The capabilities of two stators, one with controlled-diffusion (CD) blade sections and one with double-circular-arc (DCA) blade sections, were compared. A CD stator was designed and tested that had the same chord length but half the blades of the DCA stator. The same fan rotor (tip speed, 429 m/sec; pressure ratio, 1.65) was used with each stator row. The design and analysis system is briefly described. The overall stage and rotor performances with each stator are compared, as are selected blade element data. The minimum overall efficiency decrement across the stator was approximately 1 percentage point greater with the CD balde sections than with the DCA blade sections.

Gelder, Thomas F.↗

NASA NTRS1987

Design and performance of controlled-diffusion stator compared with original double-circular-arc stator

Gelder, Thomas F.↗