Search NASA⌕ Search

SEARCH · Search NASA

Results for “SHEAR PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Nondestructive techniques for characterizing mechanical properties of structural materials: An overview

An overview of nondestructive evaluation (NDE) is presented to indicate the availability and application potentials of techniques for quantitative characterization of the mechanical properties of structural materials. The purpose is to review NDE techniques that go beyond the usual emphasis on flaw detection and characterization. Discussed are current and emerging NDE techniques that can verify and monitor entrinsic properties (e.g., tensile, shear, and yield strengths; fracture toughness, hardness, ductility; elastic moduli) and underlying microstructural and morphological factors. Most of the techniques described are, at present, neither widely applied nor widely accepted in commerce and industry because they are still emerging from the laboratory. The limitations of the techniques may be overcome by advances in applications research and instrumentation technology and perhaps by accommodations for their use in the design of structural parts.

Vary, A.↗
NASA NTRS1985

Differences in interfacial bond strengths of graphite fiber-epoxy resin composites

The effect of epoxy-size and degree of cure on the interfacial bonding of an epoxy-amine-graphite fiber composite system is examined. The role of the fiber-resin interface in determining the overall mechanical properties of composites is poorly understood. A good interfacial adhesive bond is required to achieve maximum stress transfer to the fibers in composites, but at the same time some form of energy absorbing interfacial interaction is needed to achieve high fracture toughening. The incompatibility of these two processes makes it important to understand the nature and basic factors involved at the fiber-resin interface as stress is applied. The mechanical properties including interlaminar shear values for graphite fiber-resin composites are low compared to glass and boron-resin composites. These differences have been attributed to poor fiber-matrix adhesion. Graphite fibers are commonly subjected to post-treatments including application of organic sizing in order to improve their compatibility with the resin matrix and to protect the fiber tow from damage during processing and lay-up. In such processes, sized graphite fiber tow is impregnated with epoxy resin and then layed-up i nto the appropriate configuration. Following an extended ambient temperature cure, the graphite-resin composite structure is cured at elevated temperature using a programmed temperature sequence to cure and then cool the product.

Needles, H. L.↗
NASA NTRS1986

Nondestructive techniques for characterizing mechanical properties of structural materials - An overview

An overview of nondestructive evaluation (NDE) is presented to indicate the availability and application potentials of techniques for quantitative characterization of the mechanical properties of structural materials. The purpose is to review NDE techniques that go beyond the usual emphasis on flow detection and characterization. Discussed are current and emerging NDE techniques that can verify and monitor entrinsic properties (e.g., tensile, shear, and yield strengths; fracture toughness, hardness, ductility; elastic moduli) and underlying microstructural and morphological factors. Most of the techniques described are, at present, neither widely applied nor widely accepted in commerce and industry because they are still emerging from the laboratory. The limitations of the techniques may be overcome by advances in applications research and instrumentation technology and perhaps by accommodations for their use in the design of structural parts.

Vary, A.↗
NASA NTRS1986

Mechanical properties for durability predictions of FRP bonded joint

A discussion of current standard durability prediction methodology for bonded joints is given. The influence of time-dependent adhesive properties on lap shear stress distributions and interfacial stresses is presented. It is suggested that these effects may be important in durability considerations. Test geometries from which better durability information can be obtained are outlined and a general mechanics approach for durability prediction is suggested.

Brinson, H. F.↗
NASA NTRS1988

Body force circulation and the Antarctic Ozone minimum

A dynamical mechanism, which is relevant to the ozone-depletion problem and which involves a 'body force' circulation discussed by Eliassen (1951), is considered. The body force problem and its application to 'generic' upper-tropospheric wave-driving are discussed theoretically. Following a review of the interhemispheric differences in the winter and early-spring circulation, the elliptic equation governing the residual mean meridional streamfunction is derived, and its analytic-solution properties in negligible shear are discussed. Finally, a numerical solution is derived using the observed August winds under the assumption of radiative equilibrium, and the effect of diabatic heating is discussed.

Dunkerton, Timothy J.↗
NASA NTRS1989

Quality Evaluation By Acousto-Ultrasonic Testing Of Composites

Promising nondestructive-testing method based on ultrasonic simulation of stress waves. Report reviews acousto-ultrasonic technology for nondestructive testing. Discusses principles, suggests advanced signal-analysis schemes for development, and presents potential applications. Acousto-ultrasonics applied principally to assess defects in laminated and filament-wound fiber-reinforced composite materials. Technique used to determine variations in such properties as tensile, shear, and flexural strengths and reductions in strength and toughness caused by defects. Also used to evaluate states of cure, porosities, orientation of fibers, volume fractions of fibers, bonding between fibers and matrices, and qualities of interlaminar bonds.

Vary, Alex↗
NASA NTRS1991

LDEF-space environmental effects on materials: Composites and silicone coatings

The objective of the Lockheed experiment is to evaluate the effects of long term low Earth orbit environments on thermal control coatings and organic matrix/fiber reinforced composites. Two diverse categories are reported: silicone coatings and composites. For composites physical and structural properties were analyzed; results are reported on mass/dimensional loss, microcracking, short beam shear, CTE, and flexural properties. The changes in thermal control properties, mass, and surface chemistry and morphology are reported and analyzed for the silicon coatings.

Petrie, Brian C.↗
NASA NTRS1990

LaRC-TPI 1500 composites fabricated using an aqueous slurry process

Unidirectional composites from unsized carbon fiber and LaRC-TPI matrix material were fabricated using 'high flow' and'medium flow' grades of the LaRC-TPI 1500 series of polyimides. Prepreg was drum-wound from a slurry composed of the polyimide powder dispersed in an aqueous solution of LaRC-TPI poly(amide acid). The poly(amide acid) was found to be an effective binding agent in the prepregging process. Composite short beam shear and flexure properties were measured at room and elevated temperatures (to 177 C) with both dry and moisture-saturated specimens. The mechanical properties observed for composites fabricated from the high and medium flow materials were virtually identical. Additionally, double cantilever beam measurements showed nearly equivalent fracture toughness for the two composite materials.

Towell, Timothy W.↗
NASA NTRS1993

Flexure-torsion behavior of prismatic beams. I - Section properties via power series

The behavior of a tip-loaded cantilever beam with an arbitrary cross section is studied using Saint-Venant's semi-inverse method along with a power series solution for the out-of-plane flexure and torsion warping functions. The power series coefficients are determined by solving a set of variationally derived linear algebraic equations. For complex cross sections, the calculated coefficients represented a 'best-fit approximation' to the exact warping function. The resulting warping functions are used to determine the cross-sectional properties (torsion constant, shear correction factors, shear deformation coefficients, and shear center location). A new linear relation is developed for locating the shear center, where the twist rate is zero about the line of shear centers. Moreover, the kinematic relations for a new fully compatible one-dimensional beam theory are developed. Numerical results are presented first to verify the approach and second to provide section data on NACA four-series airfoils not currently found in the literature.

Kosmatka, J. B.↗
NASA NTRS1994

Turbulence models and Reynolds analogy for two-dimensional supersonic compression ramp flow

Results of the application of turbulence models and the Reynolds analogy to the Navier-Stokes computations of Mach 2.9 two-dimensional compression ramp flows are presented. The Baldwin-Lomax eddy viscosity model and the kappa-epsilon turbulence transport equations for the turbulent momentum flux modeling in the Navier-Stokes equations are studied. The Reynolds analogy for the turbulent heat flux modeling in the energy equation was also studied. The Navier-Stokes equations and the energy equation were numerically solved for the flow properties. The Reynolds shear stress, the skin friction factor, and the surface heat transfer rate were calculated and compared with their measurements. It was concluded that with a hybrid kappa-epsilon turbulence model for turbulence modeling, the present computations predicted the skin friction factors of the 8 deg and 16 deg compression ramp flows and with the turbulent Prandtl number Pr(sub t) = 0.93 and the ratio of the turbulent thermal and momentum transport coefficients mu(sub q)/mu(sub t) = 2/Prt, the present computations also predicted the surface heat transfer rates beneath the boundary layer flow of the 16 compression ramp.

Wang, Chi R.↗
NASA NTRS1994

Cryogenic Gellant and Fuel Formulation for Metallized Gelled Propellants: Hydrocarbons and Hydrogen with Aluminum

An experimental program to determine the viability of nanoparticulate gellant materials for gelled hydrocarbons and gelled liquid hydrogen was conducted. The gellants included alkoxides (BTMSE and BTMSH) and silica-based materials. Hexane, ethane, propane and hydrogen were gelled with the newly-formulated materials and their rheological properties were determined: shear stress versus shear rate and their attendant viscosities. Metallized hexane with aluminum particles was also rheologically characterized. The propellant and gellant formulations were selected for the very high surface area and relatively-high energy content of the gellants. These new gellants can therefore improve rocket engine specific impulse over that obtained with traditional cryogenic-fuel gellant materials silicon dioxide, frozen methane, or frozen ethane particles. Significant reductions in the total mass of the gellant were enabled in the fuels. In gelled liquid hydrogen, the total mass of gellant was reduced from 10-40 wt percent of frozen hydrocarbon particles to less that 8 wt percent with the alkoxide.

Wong, Wing↗
NASA NTRS2001

Room Temperature Creep Of SiC/SiC Composites

During a recent experimental study, time dependent deformation was observed for a damaged Hi-Nicalon reinforced, BN interphase, chemically vapor infiltrated SiC matrix composites subjected to static loading at room temperature. The static load curves resembled primary creep curves. In addition, acoustic emission was monitored during the test and significant AE activity was recorded while maintaining a constant load, which suggested matrix cracking or interfacial sliding. For similar composites with carbon interphases, little or no time dependent deformation was observed. Evidently, exposure of the BN interphase to the ambient environment resulted in a reduction in the interfacial mechanical properties, i.e. interfacial shear strength and/or debond energy. These results were in qualitative agreement with observations made by Eldridge of a reduction in interfacial shear stress with time at room temperature as measured by fiber push-in experiments.

Morscher, Gregory N.↗
NASA NTRS2009

Thermodynamic Approach to Enhanced Dispersion and Physical Properties in a Carbon Nanotube/Polypeptide Nanocomposite

A high molecular weight synthetic polypeptide has been designed which exhibits favorable interactions with single wall carbon nanotubes (SWCNTs). The enthalpic and entropic penalties of mixing between these two molecules are reduced due to the polypeptide's aromatic sidechains and helical secondary structure, respectively. These enhanced interactions result in a well dispersed SWCNT/Poly (L-Leucine-ran-L-Phenylalanine) nanocomposite with enhanced mechanical and electrical properties using only shear mixing and sonication. At 0.5 wt% loading of SWCNT filler, the nanocomposite exhibits simultaneous increases in the Young's modulus, failure strain, and toughness of 8%, 120%, and 144%, respectively. At one kHz, the same nanotube loading level also enhances the dielectric constant from 2.95 to 22.81, while increasing the conductivity by four orders of magnitude.

Lovell, Conrad S.↗
NASA NTRS2010

Phenylethynyl Terminated Imide (PETI) Composites Made by High Temperature VARTM

Fabrication of composite structures using vacuum assisted resin transfer molding (VARTM) is generally more affordable than conventional autoclave techniques. Recent efforts have focused on adapting VARTM for the fabrication of high temperature composites. Due to their low melt viscosity and long melt stability, certain phenylethynyl terminated imides (PETI) can be processed into composites using high temperature VARTM (HT-VARTM). However, one of the disadvantages of the current HT-VARTM resin systems has been the high porosity of the resultant composites. For aerospace applications, a void fraction of <2% is desired. In the current study, two PETI resins, LARC. PETI-330 and LARC. PETI-8 have been used to fabricate test specimens using HT-VARTM. The resins were infused into carbon fiber preforms at 260 C and cured between 316 and 371 C. Photomicrographs of the panels were taken and void contents were determined by acid digestion. Modifications to the thermal cycle used in the laminate fabrication have reduced the void content significantly; typically .3% for carbon fiber biaxially woven fabric and less than 2% for carbon fiber uniaxial fabric. Mechanical properties (short beam shear and flexure) of the panels were determined at both room and elevated temperatures. The results of this work are presented herein. This paper is declared a work of the U.S. Government and is not subject to copyright protection in the United States.

Chose, Sayata↗
NASA NTRS2011

Infusion Processing of Phenylethynyl Terminated Imides by High Temperature RTM and VARTM

Fabrication of composite structures using infusion processes such as resin transfer molding (RTM) and vacuum assisted resin transfer molding (VARTM) is generally more affordable than conventional autoclave techniques. Recent efforts have focused on adapting both technologies for the fabrication of high temperature (HT) resistant composites. Due to their low melt viscosity and long melt stability, certain phenylethynyl terminated imides (PETI) can be processed into composites using these high temperature out-of-autoclave processes. In the current study, two PETI resins, LARC(TradeMark) PETI-330 and LARC(TradeMark) PETI-8 have been used to make test specimens using both RTM and VARTM. For aerospace applications, a void fraction of less than 2% is desired. Traditionally, RTM has had the advantage over VARTM for generating composites with low void content. However, the process is limited in terms of size. Work at NASA LaRC has incorporated modifications to the thermal cycle used in laminate fabrication that have reduced the void content significantly (typically 1-3%) using the current HT-VARTM process. For composite fabrication by both RTM and VARTM, the resins were infused into three carbon fiber preforms (T650-35-3k 5HS, IM7-6k 5HS, and IM7-6k Uniweave) at 316 C and 260 C respectively and cured up to 371 C. The details of the RTM processing carried out at the University of Akron are discussed in this work along with a brief description of the HT-VARTM processing carried out at NASA-LaRC. Photomicrographs of the panels were taken and void contents were determined by acid digestion. Mechanical properties (short beam shear, SBS) of the panels fabricated by both infusion processes were determined at room temperature as well as at various elevated temperatures. The results of this work are presented herein.

Ghose, Sayata↗
NASA NTRS2016

Mechanical Model Development for Composite Structural Supercapacitors

Novel composite structural supercapacitor concepts have recently been developed as a means both to store electrical charge and to provide modest mechanical load carrying capability. Double-layer composite supercapacitors are often fabricated by impregnating a woven carbon fiber fabric, which serves as the electrodes, with a structural polymer electrolyte. Polypropylene or a glass fabric is often used as the separator material. Recent research has been primarily limited to evaluating these composites experimentally. In this study, mechanical models based on the Multiscale Generalized Method of Cells (MSGMC) were developed and used to calculate the shear and tensile properties and response of two composite structural supercapacitors from the literature. The modeling approach was first validated against traditional composite laminate data. MSGMC models for composite supercapacitors were developed, and accurate elastic shear/tensile properties were obtained. It is envisioned that further development of the models presented in this work will facilitate the design of composite components for aerospace and automotive applications and can be used to screen candidate constituent materials for inclusion in future composite structural supercapacitor concepts.

Micromechanics↗
NASA NTRS2020

Quantification of the Land Surface and Brown Ocean Influence on Tropical Cyclone Intensification Over Land

An investigation of TC Kelvin in February 2018 over northeast Australia was conducted to understand the mechanisms of the Brown Ocean effect (BOE), and to develop a comprehensive analysis framework for land falling tropical cyclones (TCs) in the process. NASA’s Land Information System (LIS) coupled to the NASA Unified WRF (NU-WRF) system was employed as the numerical model framework for 12 land/soil moisture perturbation experiments. Impacts of soil moisture and surface enthalpy flux conditions on TC Kelvin were investigated by closely evaluating simulated track and intensity, midlevel atmospheric thermodynamic properties, vertical wind shear, total precipitable water (TPW), and surface moisture flux. The results suggest that there were recognized differentiations among the sensitivity simulations as a result of land surface (e.g., soil moisture and texture) conditions. However, the intensification of TC Kelvin over land was more strongly related to atmospheric moisture advection and the diurnal cycle of solar radiation (i.e., radiative cooling) than to overall soil moisture conditions or surface fluxes. The analysis framework employed here for TC Kelvin can serve as a foundation to specifically quantify the factors governing the BOE. It also demonstrates that the BOE is not a binary influence (i.e. all or nothing), but instead operates in a continuum from largely to minimally influential such that it could be utilized to help improve prediction of inland effects for all land falling TCs.

Jinwoong Yoo↗
NASA NTRS2020

Quantification of the Land Surface and Brown Ocean Influence on Tropical Cyclone Intensification Over Land

An investigation of TC Kelvin in February 2018 over northeast Australia was conducted to understand the mechanisms of the Brown Ocean effect (BOE), and to develop a comprehensive analysis framework for landfalling tropical cyclones (TCs) in the process. NASA’s Land Information System (LIS) coupled to the NASA Unified WRF (NU-WRF) system was employed as the numerical model framework for 12 land/soil moisture perturbation experiments. Impacts of soil moisture and surface enthalpy flux conditions on TC Kelvin were investigated by closely evaluating simulated track and intensity, midlevel atmospheric thermodynamic properties, vertical wind shear, total precipitable water (TPW), and surface moisture flux. The results suggest that there were recognized differentiations among the sensitivity simulations as a result of land surface (e.g., soil moisture and texture) conditions. However, the intensification of TC Kelvin over land was more strongly related to atmospheric moisture advection and the diurnal cycle of solar radiation (i.e., radiative cooling) than to overall soil moisture conditions or surface fluxes. The analysis framework employed here for TC Kelvin can serve as a foundation to specifically quantify the factors governing the BOE. It also demonstrates that the BOE is not a binary influence (i.e. all or nothing), but instead operates in a continuum from largely to minimally influential such that it could be utilized to help improve prediction of inland effects for all landfalling TCs.

Brown Ocean Effect↗