Results for “SHEAR PROPERTIES” — Page 11

NASA NTRS1987

The acousto-ultrasonic approach

The nature and underlying rationale of the acousto-ultrasonic approach is reviewed, needed advanced signal analysis and evaluation methods suggested, and application potentials discussed. Acousto-ultrasonics is an NDE technique combining aspects of acoustic emission methodology with ultrasonic simulation of stress waves. This approach uses analysis of simulated stress waves for detecting and mapping variations of mechanical properties. Unlike most NDE, acousto-ultrasonics is less concerned with flaw detection than with the assessment of the collective effects of various flaws and material anomalies. Acousto-ultrasonics has been applied chiefly to laminated and filament-wound fiber reinforced composites. It has been used to assess the significant strength and toughness reducing effects that can be wrought by combinations of essentially minor flaws and diffuse flaw populations. Acousto-ultrasonics assesses integrated defect states and the resultant variations in properties such as tensile, shear, and flexural strengths and fracture resistance. Matrix cure state, porosity, fiber orientation, fiber volume fraction, fiber-matrix bonding, and interlaminar bond quality are underlying factors.

Vary, Alex↗

NASA NTRS1988

The acousto-ultrasonic approach

The nature and underlying rationale of the acousto-ultrasonic approach is reviewed, needed advanced signal analysis and evaluation methods suggested, and application potentials discussed. Acousto-ultrasonics is an NDE technique combining aspects of acoustic emission methodology with ultrasonic simulation of stress waves. This approach uses analysis of simulated stress waves for detecting and mapping variations of mechanical properties. Unlike most NDE, acousto-ultrasonics is less concerned with flaw detection than with the assessment of the collective effects of various flaws and material anomalies. Acousto-ultrasonics has been applied chiefly to laminated and filament-wound fiber reinforced composites. It has been used to assess the significant strength and toughness reducing effects that can be wrought by combinations of essentially minor flaws and diffuse flaw populations. Acousto-ultrasonics assesses integrated defect states and the resultant variations in properties such as tensile, shear, and flexural strengths and fracture resistance. Matrix cure state, porosity, fiber orientation, fiber volume fraction, fiber-matrix bonding, and interlaminar bond quality are underlying factors.

Vary, Alex↗

NASA NTRS1989

Improvements and applications of a streamwise upwind algorithm

An improved streamwise upwind algorithm has been used to study conical flow fields. In the present method, additional terms have been introduced in the cross-flow direction to prevent solution decoupling in supersonic flows, and the local Mach number is taken into account in order to evaluate the rotated differencing. It is found that the formula captures oblique shock waves in the same manner as Roe's (1986) formula, has good convergence properties, and accurately computes shear flows.

Obayashi, Shigeru↗

NASA NTRS1989

On hypersonic shock layer and its extension beyond the Navier-Stokes level

An extension of the continuum model beyond the Navier-Stokes (NS) level and related issues on problem formulation are examined for a hypersonic shock layer on the basis of Grad's thirteen-moment equations for a Maxwell gas. The 13-moment system, simplified consistently with a fully viscous version of the thin shock-layer approximation, permits correlation with the corresponding NS-based solution. With the exception of pressure and density, several flow properties including normal stress, shear stress and normal heat flux along a streamline are unaffected by translational nonequilibrium and are therefore predicted correctly by the NS solution to the leading order, even in a domain far from translational equilibrium where molecular-transport processes rank equally with the convection.

Cheng, H. K.↗

NASA NTRS2001

Longtime Durability of PMR-15 Matrix Polymer at 204, 260, 288, and 316 C

Isothermal weight loss studies at the Glenn (Lewis) Research Center were conducted at four temperatures (204, 260, 288, and 316 C) with specimens of varied geometric shapes to investigate the mechanisms involved in the thermal degradation of PMR-15. Both neat resin behavior and composite behaviors were studied. Two points of interest in these studies are the role(s) of oxygen in the mechanisms involved in the thermo-oxidative degradation of these composite materials and the dimensional changes that occur during their useable lifetime. Specimen dimensional changes and surface layer growth were measured and recorded. It was shown that physical and chemical changes take place as a function of time and location in PMR-15 neat resin and composites as aging takes place in air at elevated temperatures. These changes initiate at the outer surfaces of both materials and progress inward following the oxygen as it proceeds by diffusion into the central core of each material. Microstructural changes cause changes in density, material shrinkage (strains), glass transition temperature, dimension, dynamic shear modulus, and compression properties. These changes also occur slowly dividing the polymer material into two distinct parts: a visibly undamaged core section between two visibly damaged surface layers. The surface layer has a significant effect on compression properties of thinner specimens, but the visibly undamaged core material controls these properties for specimens having eight or more plies. It was demonstrated that there are three different mechanisms involved in the degradation of PMR-15 during aging at elevated temperatures. These are a weight gain, a small weight fraction bulk material weight loss, and a large mass fraction weight loss concentrated at the surface of the polymer or composite. At the higher temperatures (260 C and above), the surface loss predominates. Below 260 C, the surface loss and the bulk core loss become more equivalent. Between 175 and 260 C, the initial weight change is due to a weight gain mechanism with a visible lifetime that diminishes as the aging temperature increases.

Bowles, Kenneth J.↗

NASA NTRS2005

Estimating Aeroheating of a 3D Body Using a 2D Flow Solver

A method for rapidly estimating the aeroheating, shear stress, and other properties of hypersonic flow about a three-dimensional (3D) blunt body has been devised. First, the geometry of the body is specified in Cartesian coordinates. The surface of the body is then described by its derivatives, coordinates, and principal curvatures. Next, previously relatively simple equations are used to find, for each desired combination of angle of attack and meridional angle, a scaling factor and the shape of an equivalent axisymmetric body. These factors and equivalent shapes are entered as inputs into a previously developed computer program that solves the two-dimensional (2D) equations of flow in a non-equilibrium viscous shock layer (VSL) about an axisymmetric body. The coordinates in the output of the VSL code are transformed back to the Cartesian coordinates of the 3D body, so that computed flow quantities can be registered with locations in the 3D flow field of interest. In tests in which the 3D bodies were elliptic paraboloids, the estimates obtained by use of this method were found to agree well with solutions of 3D, finite-rate-chemistry, thin-VSL equations for a catalytic body.

Scott, Carl D.↗

NASA NTRSDate not supplied

Updates to the Predictive Materials Modeling Software Tools

Updates on NASA's efforts to build predictive material models from the micro-scale to the macro-scale are presented. To complement the mission design cycle process and reduce the need for extensive testing, NASA is developing modeling and simulation tools that enable characterizing material properties and response to hot plasma experienced during atmospheric entry. The PuMA (microstructure analysis), PATO (macroscale material response), SPARTA (direct simulation Monte Carlo) and ARCHeS (arc heater modeling) codes are described. A range of applications, encompassing calculating effective material properties, study of high shear boundary layer flow over woven materials, new model of silicone-based coatings, new model of mechanical erosion, as well as approach to loose multi-physics coupling, are presented.

material modeling↗

NASA NTRS1992

Kinetic effects on the velocity-shear-driven instability

A comparison is made between the properties of the low-frequency long-wavelength velocity-shear-driven instability in kinetic theory and magnetohydrodynamics (MHD). The results show that the removal of adiabaticity along the magnetic field line in kinetic theory leads to modifications in the nature of the instability. Although the threshold for the instability in the two formalisms is the same, the kinetic growth rate and the unstable range in wave-number space can be larger or smaller than the MHD values depending on the ratio between the thermal speed, Alfven speed, and flow speed. When the thermal speed is much larger than the flow speed and the flow speed is larger than the Alfven speed, the kinetic formalism gives a larger maximum growth rate and broader unstable range in wave-number space. In this regime, the normalized wave number for instability can be larger than unity, while in MHD it is always less than unity. The normal mode profile in the kinetic case has a wider spatial extent across the shear layer.

Wang, Z.↗

NASA NTRS1979

Surface temperatures and glassy state investigations in tribology

The limiting shear stress shear rheological model was applied to property measurements pursuant to the use of the constitutive equation and the application of the constitutive equation to elastrohydrodynamic (EHD) traction. Experimental techniques were developed to subject materials to isothermal compression which is similar to the history the materials were subjected to in EHD contacts. In addition, an apparatus was developed for measuring the shear stress-strain behavior of solid lubricating materials. Four commercially available materials were examined under pressure. They exhibit elastic and limiting shear stress behavior similar to that of liquid lubricants. The application of the limiting shear stress model to traction predictions was extended employing the primary materials properties measured in the laboratory. The shear rheological model was also applied to a Grubin-like EHD inlet analysis for predicting film thicknesses when employing the limiting shear stress model material behavior.

Bair, S.↗

NASA NTRS1988

Correlations of norbornenyl crosslinked polyimide resin structures with resin thermo-oxidative stability, resin glass transition temperature and composite initial mechanical properties

PMR (polymerization of monomeric reactants) methodology was used to prepare 70 different polyimide oligomeric resins and 30 different unidirectional graphite fiber/polyimide composites. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on resin thermo-oxidative stability and glass transition temperature (Tg) of the cured/postcured resins. A linear correlation of decreasing 316 C resin weight loss/surface area versus (1) decreasing aliphatic content, or (2) increasing benzylic/aliphatic content stoichiometry ratio over a wide range of resin compositions was observed. An almost linear correlation of Tg versus molecular distance between the crosslinks was also observed. An attempt was made to correlate Tg with initial composite mechanical properties (flexural strength and interlaminar shear strength). However, the scatter in mechanical strength data prevented obtaining a clear correlation. Instead, only a range of composite mechanical properties was obtained at 25, 288, and 316 C. Perhaps more importantly, what did become apparent during the correlation study was (1) the PMR methodology could be used to prepare composites from resins containing a wide variety of monomer modifications, (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins formulated exhibited satisfactory processing flow, and (3) that PMR resins exhibited predictable rates of 316 C weight loss/surface area based on their benzylic/aliphatic stoichiometery ratio.

Alston, William B.↗

NASA NTRS1985

Solid Rocket Motor Case (SRMC) dynamic sensitivity to changes in composite properties

Traditional composite lamination theory was used to compute the constitutive matrices using a potential range of lamina properties. Sensitivity of vibrational frequencies was examined for variations in constituent materials and geometric properties. The material component interactions examined were the lamina longitudinal and transverse Young's modulus, the lamina Poisson's ratio, and the shear modulus. Fiber and resin properties were related to the frequency response through lamina properties. Geometric properties examined are void ratio and helical wind angle. Capabilities and applications of the SPAR and NASTRAN computer codes are examined for laminated cylindrical shells.

Tolbert, R. N.↗

NASA NTRS1991

Improved bounds on elastic and transport properties of fiber-reinforced composites - Effect of polydispersivity in fiber radius

Improved rigorous bounds were computed on the effective elastic and transport properties (including the effective axial shear modulus, effective transverse bulk modulus, and effective transverse shear modulus) of a transversely isotropic fiber-reinforced material composed of infinitely-long oriented multisized impenetrable circular cylinders distributed throughout a matrix. Results were used to study the effect of fiber-radius polydispersivity on the elastic and transport properties of such unidirectional composites. It was found that increasing the degree of polydispersivity increases the effective transverse conductivity (or axial shear modulus) and the effective transverse bulk modulus, and slightly decreases the effective transverse shear modulus for cases in which the fibers are more conducting or stiffer than the matrix.

Miller, C. A.↗

NASA NTRS1975

Development of procedures for calculating stiffness and damping properties of elastomers. Part 3: The effects of temperature, dissipation level and geometry

Effects of temperature, dissipation level and geometry on the dynamic behavior of elastomer elements were investigated. Force displacement relationships in elastomer elements and the effects of frequency, geometry and temperature upon these relationships are reviewed. Based on this review, methods of reducing stiffness and damping data for shear and compression test elements to material properties (storage and loss moduli) and empirical geometric factors are developed and tested using previously generated experimental data. A prediction method which accounts for large amplitudes of deformation is developed on the assumption that their effect is to increase temperature through the elastomers, thereby modifying the local material properties. Various simple methods of predicting the radial stiffness of ring cartridge elements are developed and compared. Material properties were determined from the shear specimen tests as a function of frequency and temperature. Using these material properties, numerical predictions of stiffness and damping for cartridge and compression specimens were made and compared with corresponding measurements at different temperatures, with encouraging results.

Smalley, A. J.↗

NASA NTRS1998

IM7/LARC(tm) MPEI-1 Polymide Composites

LARC(Trademark) MPEI-1 (Langley Research Center(Trademark) modified phenylethynyl imide-1) phenylethynyl containing aromatic polymide, is based on the reaction of biphenyl dianhydride (BPDA), 3,4'-oxydianiline (3,4'-ODA), 1,3-bis(3-aminophenoxy)benzene (APB), 2,4,6-triaminopyrimidine (TAP) and 4-phenylethynyl phthalic anhydride (PEPA), presumably resulting in a mixture of linear, branched and star shaped phenylethynyl containing imides which was evaluated as a matrix for high-performance composites. The poly(amid acid) solution of MPEI-1 in N-methypyrrolidinone was synthesized at 35% and 42% solids. Unidirectional prepreg was fabricated from these solutions and Hercules IM7 carbon fiber utilizing NASA- Langley's multipurpose prepreg machine. The temperature-dependent volatile depletion rates, thermal crystallization behavior and resin theology were characterized. Based on this information, a composite molding cycle was developed which yielded well consolidated, void-free laminates. Composite mechanical properties such as short beam shear strength, longitudinal and transverse flexural strength and flexural modulus, longitudinal tensile strength and notched and unnotched compression strengths were measured at room temperature (RT) and elevated temperatures. These mechanical properties are compared with those of IM7/LARC(Trademark) PETI-5 composites.

Hou, T. H.↗

NASA NTRSDate not supplied

Experimental Considerations for Ground-based Testing of Lunar Construction Technologies

The Moon-to-Mars Planetary Autonomous Construction Technology (MMPACT) project, under NASA’s Game Changing Division (GCD) aims to research, develop, and demonstrate lunar surface construction capabilities[1].A fundamental step in lunar infrastructure development is to quantify the geotechnical properties of lunar regolith, such as shear strength (Mohr-Coulomb cohesion and angle of internal friction), com-pression and bearing properties, and angle of re-pose. Knowledge of these geotechnical properties enables the prediction of forces and displacements associated with lunar infrastructure development processes including excavation and constructing landing pads, habitats, shelters, and roadways. Through ground-based testing of autonomous lunar systems performed using relevant hardware (e.g., robotic arms) in appropriate lunar regolith simulants, the developed hardware/technology and tool paths can be validated. Such testing also generates data to give insight into the geotechnical regolith properties on the lunar surface.

Regolith↗

NASA NTRS1977

The promise of eutectics for aircraft turbines

Gas turbine blades and vanes for the 1980s call for new materials with higher operational temperature capabilities. The potential increase of from 40 to 110 C in operational temperature capabilities predicted for directionally solidified eutectics is a larger increment over currently available alloys than previously obtained in any new turbine blade alloy. The paper discusses the properties of gamma/gamma prime-delta and NiTaC-13 directionally solidified first-generation eutectics for use as gas turbine blade materials. A few of the more promising second-generation eutectics for blade applications (gamma/gamma prime-alpha, NiTaC 3-116A) and for vane applications (gamma-beta, COTAC 74) are also discussed. Attention is given to mechanical properties, such as transverse ductility and shear strength, that can be inherently critical in a directionally solidified eutectic. Further R&D requirements for properties, coatings, and lower cost processing technology are identified.

Gray, H. R.↗

NASA NTRS1986

Structure-to-property Relationships in Addition Cured Polymers 2: Resin Tg Composite Initial Mechanical Properties of Norbornenyl Cured Polyimide Resins

PRM (polymerization of monomeric reactants) methodology was used to prepare thirty different polyimide oligomeric resins. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on glass transition temperature (Tg) of the cured/postcured resins. An almost linear correlation of Tg versus molecular distance between the crosslinks was observed. An attempt was made to correlate Tg with initial mechanical properties (flexural strength and interlaminar shear strength) of unidirectional graphite fiber composites prepared with these resins. However, the scatter in mechanical strength data prevented obtaining as clear a correlation as was observed for the structural modification/crosslink distance versus Tg. Instead, only a range of composite mechanical properties was obtained at the test temperatures studied (room temperature, 288 and 316 C). Perhaps more importantly, what did become apparent during the attempted correlation study was: (1) that PMR methodology could be used to prepare composites from resins that contain a wide variety of monomer modifications, and (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins selected were melt processable.

Alston, W. B.↗

NASA NTRS1986

Structure-to-property relationships in addition cured polymers. II - Resin Tg and composite initial mechanical properties of norbornenyl cured polyimide resins

PRM (polymerization of monomeric reactants) methodology was used to prepare thirty different polyimide oligomeric resins. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on glass transition temperature (Tg) of the cured/postcured resins. An almost linear correlation of Tg versus molecular distance between the crosslinks was observed. An attempt was made to correlate Tg with initial mechanical properties (flexural strength and interlaminar shear strength) of unidirectional graphite fiber composites prepared with these resins. However, the scatter in mechanical strength data prevented obtaining as clear a correlation as was observed for the structural modification/crosslink distance versus Tg. Instead, only a range of composite mechanical properties was obtained at the test temperatures studied (room temperature, 288 and 316 C). Perhaps more importantly, what did become apparent during the attempted correlation study was: (1) that PMR methodology could be used to prepare composites from resins that contain a wide variety of monomer modifications, and (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins selected were melt processable.

Alston, William B.↗