SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
This paper presents two Computational Fluid Dynamics (CFD) models of the flow in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT). The TDT is a continuous-flow, closed circuit wind tunnel with a 16- by 16-foot slotted test section with cropped corners. The tunnel was originally built as the 19-ft Pressure Tunnel in 1938, but it was converted to the current transonic tunnel in the 1950s, with capabilities to use either air or heavy gas as the test medium. The first computational model describes the generation of an atmospheric-boundary-layer (ABL) profile inside the tunnel. An ABL, which includes both a wind profile and turbulence content, is one of the aerodynamic characteristics affecting the occurrence of wind-induced oscillations for a launch vehicle sitting on a pad. The challenging part of this analysis was modeling the turbulent flow inside the tunnel. This is due to the special ABL-generating hardware that was installed at the entrance of the TDT test section in order to change the downstream velocity profile and to introduce velocity fluctuations into the flow. The second CFD model builds on the computational aeroelastic results that were generated in support of the second Aeroelastic Prediction Workshop (AePW) for the NASA Benchmark Supercritical Wing (BSCW) configuration. During the AePW, the wing-only configuration (classical free-air model) was analyzed. In the current study, the flutter computations were conducted on the configuration as it was mounted in the TDT during the experiment. This includes the wing attached to the splitter plate that was attached to the wind-tunnel walls. The preliminary results show that the wind-tunnel walls marginally affect flutter prediction.
An experimental and theoretical study of a sound shield concept to attenuate the noise radiated into the test section from the turbulent boundary layer on the walls of wind tunnels was conducted. The model investigated was planar with a sharp flat plate leading edge faired into an array of rods aligned nearly parallel to the local flow. For a ratio of gap diameter to rod diameter of 0.16, the flow was laminar over the entire model at a maximum local length Reynolds number of 14 million. A 45% reduction in the tunnel free stream root mean square pressure level was measured within the shielded region for this gap width when the boundary layers on the rods were laminar. Smaller ratios of gap diameter to rod diameter resulted in substantial reductions in the transition Reynolds number, and in a 40% pressure reduction.
Force and surface pressure distributions were measured for the 21% LS(1)-0421 modified airfoil fitted with 20% aileron, 25% slotted flap and 10% slot lip spoiler. All tests were conducted at a Reynolds number of 2.2 x 10 to the 6th power and a Mach number of 0.13. The lift, drag, pitching moments, control surface normal force and hinge moments, and surface pressure distributions are included in the results. Incremental performance of flap and aileron are discussed and compared to the GA(W)-2 airfoil. Spoiler control which shows a slight reversal tendency at high alpha, is examined.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Report presents the results of an investigation conducted in the NACA 7 by 10-foot win tunnel to determine the effect of the deflection of main and auxiliary slotted flaps on the aerodynamic section characteristics of large-chord NACA 23012, 23021, 23030 airfoils equipped with 40-percent-chord double slotted flaps. The complete aerodynamic section characteristics and envelope polar curves are given for each airfoil-flap combination. The effect of airfoil thickness is shown, and comparisons are made of single slotted flaps with double slotted flaps on each of the airfoils.
A full-scale semispan model was investigated to evaluate and document the low-speed, high-lift characteristics of a business-jet class wing that utilized the HSNLF(1)-0213 airfoil section and a single-slotted flap system. Also, boundary-layer transition effects were examined, a segmented leading-edge droop for improved stall/spin resistance was studied, and two roll-controlled devices were evaluated. The wind-tunnel investigation showed that deployment of single-slotted, trailing-edge flap was effective in providing substantial increments in lift required for takeoff and landing performance. Fixed-transition studies to investigate premature tripping of the boundary layer indicated no adverse effects in lift and pitching-moment characteristics for either the cruise or landing configuration. The full-scale results also suggested the need to further optimize the leading-edge droop design that was developed in the subscale tests.
Lift and drag tests were made on a Clark Y wing equipped with four fixed slots and a trailing-edge flap in the 5-foot vertical wind tunnel of the National Advisory Committee for Aeronautics. All possible combinations of the four slots were tested with the flap neutral and the most promising combinations were tested with the flap down 45 degrees. Considering both the maximum lift coefficient and the speed-range ratio with the flap neutral no appreciable improvement was found with the use of more than the single leading-edge slot. With the flap down 45 degrees a maximum lift coefficient of 2.60 was obtained but the particular slot combination used had a rather large minimum drag coefficient with the flap neutral. With the flap down 45 degrees the optimum combination, considering both the maximum lift coefficient and the speed-range ratio, was obtained with only the two rearmost slots in use. For this arrangement the maximum lift coefficient was 2.44.
Hersh Walker Acoustics (HWA) has performed a series of wind tunnel tests to support crack-repair studies for ITA flowliner vent slots. The overall goal of these tests is to determine if slot shape details have a significant influence on the propensity of the flowliner to produce aero-acoustic oscillations that could increase unsteady stresses on the flowliner walls. The test series, conducted using a full-scale two-dimensional model of a six-slot segment of the 38 slot liner, was intended to investigate the effects of altering slot shape by grinding away cracked portions.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
This paper presents a Computational Fluid Dynamics (CFD) model of the flow in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT) with the Airstream Oscillator System (AOS) in operation. The TDT is a continuous-flow, closed circuit wind tunnel with a 16- by 16-foot slotted test section with cropped corners. The tunnel was originally built as the 19-ft Pressure Tunnel in 1938, but it was converted to the current transonic tunnel in the 1950s, with capabilities to use either air or heavy gas (R-134a) as the test medium. The TDT was also fitted with an AOS which can be used to create a gust field in the test section. To date, no computational analyses of the TDT involving the AOS have been performed. In this study, experimental data acquired of an oscillating airstream in the tunnel will be used to calibrate the computational analyses. A significant motivation of this work is to attempt to compare computational gust velocities to those recorded in the TDT literature. In addition to a validation of this model with experimental data, it may also be possible to supplement the experimental data with computational data. The experimental data is rather sparse and at only a few Mach numbers. Computational results may be able to expand the AOS data set. Another motivation for this work is that the Integrated Adaptive Wing Technology Maturation (IAWTM) semi-span model of the high-aspect-ratio CRM with 10 trailing edge control surfaces is currently being fabricated and will be delivered to the NASA Langley Transonic Dynamics Tunnel (TDT) for testing in late 2020. Among tests to be conducted, gust load alleviation (GLA) will be demonstrated at transonic conditions using the AOS.
The TURBO-AE aeroelastic code has been used to verify the flutter stability of the trailing edge blowing (TEB) fan, which is a unique technology demonstrator being designed and fabricated at the NASA Glenn Research Center for testing in Glenn s 9- by 15-Foot Low-Speed Wind Tunnel. Air can be blown out of slots near the trailing edges of the TEB fan blades to fill in the wakes downstream of the rotating blades, which reduces the rotor-stator interaction (tone) noise caused by the interaction of wakes with the downstream stators. The TEB fan will demonstrate a 1.6-EPNdB reduction in tone noise through wake filling. Furthermore, the reduced blade-row interaction will decrease the possibility of forced-response vibrations and enable closer spacing of blade rows, thus reducing engine length and weight. The detailed aeroelastic analysis capability of the three-dimensional Navier-Stokes TURBO-AE code was used to check the TEB fan rotor blades for flutter stability. Flutter calculations were first performed with no TEB flow; then select calculations were repeated with TEB flow turned on.
A low speed wind tunnel test was conducted in the Langley V/STOL tunnel to determine the static longitudinal and lateral stability characteristics of a general research model which simulated an advance configuration for a commercial transport airplane with a T tail. The model had a 42 deg swept, aspect ratio 6.78 wing with a supercritical airfoil and a high lift system which consisted of a leading edge slat and a double slotted flap. Various slat and flap deflection combinations represented clean, take off, and landing configurations. Effects on the longitudinal and lateral aerodynamic characteristics were determined for two flow through, simulated engine nacelles located on the sides of the fuselage near the rear of the model.
Explore the source record for details and available documents.