Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS RELAXATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Relaxation dynamics of deformed polymer nanocomposites as revealed by small-angle scattering and rheology

Here, the relaxation dynamics of polystyrene (PS)/silica nanocomposites after a large step deformation are studied by a combination of small-angle scattering techniques and rheology. Small-angle X-ray scattering measurements and rheology show clear signatures of nanoparticle aggregation that enhances the mechanical properties of the polymer nanocomposites (PNCs) in the linear viscoelastic regime and during the initial phase of stress relaxation along with accelerated relaxation dynamics. Small-angle neutron scattering experiments under the zero-average-contrast condition reveal, however, smaller structural anisotropy in the PNCs than that in the neat polymer matrix, as well as accelerated anisotropy relaxation. In addition, the degrees of anisotropy reduction and relaxation dynamics acceleration increase with increasing nanoparticle loading. These results are in sharp contrast to the prevailing viewpoint of enhanced molecular deformation as the main mechanism for the mechanical enhancement in PNCs. Furthermore, the observed acceleration of stress relaxation and reduction in structural anisotropy point to two types of nonlinear effects in the relaxation dynamics of PNCs at large deformation.

36 MATERIALS SCIENCE↗

Time-temperature-stress dependence of boron fiber deformation

The time-dependent deformation of boron fibers over the temperature range from -190 to 800 C is studied by flexural stress relaxation and flexural internal friction techniques on 203-micron diam specimen fibers commercially produced by chemical vapor deposition (CVD) on a 13-micron tungsten substrate. It is shown that up to at least 800 C all nonelastic behavior observed during axial deformation of CVD boron fibers can be explained solely by anelastic mechanisms and that although creep strains are small, boron fiber anelasticity can produce significant mechanical effects which would otherwise be neglected under the elastic approximation. Relations are obtained to demonstrate the considerable effects of anelasticity on such fiber/composite properties as modulus, creep, creep recovery, stress relaxation, and damping capacity. For an elastic-core/anelastic-sheath model, boron fibers on tungsten substrates are shown to have predictable fracture stresses for time-temperature conditions ranging from impact to long-time stress rupture. Possible techniques for altering these stresses are discussed.

Dicarlo, J. A.↗

NUMERICAL SIMULATION FOR MECHANICAL BEHAVIOR OF U10MO MONOLITHIC MINIPLATES FOR RESEARCH AND TEST REACTORS

This article presents assessment of the mechanical behavior of U-10wt% Mo (U10Mo) alloy based monolithic fuel plates subject to irradiation. Monolithic, plate-type fuel is a new fuel form being developed for research and test reactors to achieve higher uranium densities within the reactor core to allow the use of low-enriched uranium fuel in high-performance reactors. Identification of the stress/strain characteristics is important for understanding the in-reactor performance of these plate-type fuels. For this work, three distinct cases were considered: (1) fabrication induced residual stresses (2) thermal cycling of fabricated plates; and finally (3) transient mechanical behavior under actual operating conditions. Because the temperatures approach the melting temperature of the cladding during the fabrication and thermal cycling, high temperature material properties were incorporated to improve the accuracy. Once residual stress fields due to fabrication process were identified, solution was used as initial state for the subsequent simulations. For thermal cycling simulation, elasto-plastic material model with thermal creep was constructed and residual stresses caused by the fabrication process were included. For in-service simulation, coupled fluid-thermal-structural interaction was considered. First, temperature field on the plates was calculated and this field was used to compute the thermal stresses. For time dependent mechanical behavior, thermal creep of cladding, volumetric swelling and fission induced creep of the fuel foil were considered. The analysis showed that the stresses evolve very rapidly in the reactor. While swelling of the foil increases the stress of the foil, irradiation induced creep causes stress relaxation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Factors Influencing Dwell Fatigue Cracking in Notches of Powder Metallurgy Superalloys

The influences of heat treatment and cyclic dwells on the notch fatigue resistance of powder metallurgy disk superalloys were investigated for low solvus high refractory (LSHR) and ME3 disk alloys. Disks were processed to produce material conditions with varied microstructures and associated mechanical properties. Notched specimens were first subjected to baseline dwell fatigue cycles having a dwell at maximum load, as well as tensile, stress relaxation, creep rupture, and dwell fatigue crack growth tests at 704 C. Several material heat treatments displayed a bimodal distribution of fatigue life with the lives varying by two orders-of-magnitude, while others had more consistent fatigue lives. This response was compared to other mechanical properties, in search of correlations. The wide scatter in baseline dwell fatigue life was observed only for material conditions resistant to stress relaxation. For selected materials and conditions, additional tests were then performed with the dwells shifted in part or in total to minimum tensile load. The tests performed with dwells at minimum load exhibited lower fatigue lives than max dwell tests, and also exhibited early crack initiation and a substantial increase in the number of initiation sites. These results could be explained in part by modeling evolution of peak stresses in the notch with continued dwell fatigue cycling. Fatigue-environment interactions were determined to limit life for the fatigue cycles with dwells.

Gabb, T. P.↗

Techniques to characterize dynamics in biomaterials microenvironments: XPCS and microrheology of alginate/PEO–PPO–PEO hydrogels

Many recent studies have highlighted the timescale for stress relaxation of biomaterials on the microscale as an important factor in regulating a number of cell-material interactions, including cell spreading, proliferation, and differentiation. Relevant timescales on the order of 0.1–100 s have been suggested by several studies. While such timescales are accessible through conventional mechanical rheology, several biomaterials have heterogeneous structures, and stress relaxation mechanisms of the bulk material may not correspond to that experienced in the cellular microenvironment. Here we employ X-ray photon correlation spectroscopy (XPCS) to explore the temperature-dependent dynamics, relaxation time, and microrheology of multicomponent hydrogels comprising of commercial poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (PEO–PPO–PEO) triblock copolymer F127 and alginate. Previous studies on this system have shown thermoreversible behavior in the bulk oscillatory shear rheology. At physiological temperatures, bulk rheology of these samples shows behavior characteristic of a soft solid, with G' > G" and no crossover between G' and G" over the measurable frequency range, indicating a relaxation time >125 s. By contrast, XPCS-based microrheology shows viscoelastic behavior at low frequencies, and XPCS-derived correlation functions show relaxation times ranging from 10–45 s on smaller length scales. Finally, we are able to use XPCS to effectively probe the viscoelasticity and relaxation behavior within the material microenvironments.

36 MATERIALS SCIENCE↗

Failure behavior after stepwise uniaxial extension of entangled polymer melts

This paper studies how stepwise extension of various well-entangled polymer melts produce mechanical/structural breakdowns during stress relaxation. Depending on how stepwise extension is imposed on five different styrene-butadiene random copolymers, two different forms of specimen failure are observed. When a step extension is produced with a low Hencky rate or to a low strain below some thresholds, the sample breaks up rather sharply after an appreciable period of induction during which the stress relaxes quiescently. After step extension, the sample draws and undergoes unsustainable necking due to shear yielding, if the step extension is produced with a Hencky rate higher than the Rouse relaxation rate and the magnitude is beyond a Hencky strain of 1.5. Moreover, introduction of long-chain branching suppresses the elastic breakup, postponing it to Hencky strains beyond 2.5. The clearly identifiable characteristics of the elastic yielding may be understood in terms of some speculative interpretations. Finally, more convincing explanations have yet to come from future computer experiments that hopefully the present work is able to motivate.

36 MATERIALS SCIENCE↗

Viscoelastic properties of addition-cured polyimides used in high temperature polymer matrix composites

The viscoelastic properties of an addition-cured polyimide, PMR-15, were evaluated through dynamic mechanical and stress relaxation testing. Below the glass transition temperature, the dynamic mechanical properties of the composites are strongly affected by the absorbed moisture in the resin. At temperature 20 C and more above the glass transition temperature, the storage modulus increases continuously with time, indicating that additional crosslinking is occurring in the resin. For resin moisture contents less than 2 percent, stress relaxation curves measured at different temperatures can be superimposed using horizontal shifts along the log(time) axis with only small shifts along the vertical axis.

Roberts, Gary D.↗

The effect of physical aging on the time-dependent properties of carbon-fiber-reinforced epoxy composites

Annealing in nitrogen below the glass transition temperature T(g) is found to affect the matrix-dominated physical properties of postcured, (+ and -45)2s specimens of Thornel 300 carbon fiber/Fiberite 934 epoxy composite as well as neat Fiberite 934 epoxy resin. The damping behavior, stress-relaxation rate and enthalpic state of the matrix material are found to decrease as functions of annealing time. The time-dependent change in physical properties is explained on the basis of free-volume collapse related to the physical aging of the nonequilibrium glassy network of epoxy. Such physical aging in network epoxy has been demonstrated to be thermoreversible through the monitoring of its kinetics by differential scanning calorimetry, stress relaxation tests, and dynamic mechanical analysis.

Kong, E. S. W.↗

Effects of elevated temperature on the viscoplastic modeling of graphite/polymeric composites

To support the development of new materials for the design of next generation supersonic transports, a research program is underway at NASA to assess the long term durability of advanced polymer matrix composites (PMC's). One of main objectives of the program was to explore the effects of elevated temperature (23 to 200 C) on the constitutive model's material parameters. To achieve this goal, test data on the observed nonlinear, stress-strain behavior of IM7/5260 and IM7/8320 composites under tension and compression loading were collected and correlated against temperature. These tests, conducted under isothermal conditions using variable strain rates, included such phenomena as stress relaxation and short term creep. The second major goal was the verification of the model by comparison of analytical predictions and test results for off axis and angle ply laminates. Correlation between test and predicted behavior was performed for specimens of both material systems over a range of temperatures. Results indicated that the model provided reasonable predictions of material behavior in load or strain controlled tests. Periods of loading, unloading, stress relaxation, and creep were accounted for.

Gates, Thomas S.↗

Performance of Bolted Closure Joint Elastomers Under Cask Aging Conditions

The bolted closure joint of a bare spent fuel cask is susceptible to age-related degradation and potential loss of confinement function under long-term storage conditions. Elastomeric seals, a component of the joint typically used to facilitate leak testing of the primary seal that includes the metallic seal and bolting, is susceptible to degradation over time by several mechanisms, principally via thermo-oxidation, stress-relaxation, and radiolytic degradation under time and temperature condition. Irradiation and thermal exposure testing and evaluation of an ethylene-propylene diene monomer (EPDM) elastomeric seal material similar to that used in the CASTOR® V/21 cask for a matrix of temperature and radiation exposure conditions relevant to the cask extended storage conditions, and development of semiempirical predictive models for loss of sealing force is in progress. A special insert was developed to allow Compressive Stress Relaxation (CSR) measurements before and after the irradiation and/or thermal exposure without unloading the elastomer. A condition of the loss of sealing force for the onset of leakage was suggested. The experimentation and modeling being performed could enable acquisition of extensive coupled aging data as well as an estimation of the timeframe when loss of sealing function under aging (temperature/radiation) conditions may occur.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Influence of physical aging on the time-dependent properties of network epoxies and epoxy-matrix composites

The matrix-dominated properties of a network epoxy and its carbon fiber-reinforced composite are noted to be affected by sub-glass transition temperature T(g) annealing in a nitrogen atmosphere. The damping behavior, stress relaxation rate, and enthalpic state of the matrix material were found to decrease as functions of sub-T(g) annealing time. This time-dependent change in physical properties is explained on the basis of a free-volume collapse which is related to the recovery process of the nonequilibrium glassy network of the epoxy. The physical aging in network epoxies has been demonstrated to be thermoreversible. Aging kinetics are studied by means of differential scanning calorimetry, stress relaxation tests, dynamic mechanical analysis, and thermomechanical analysis.

Kong, E. S. W.↗

A survey of unified constitutive theories

The state of the art of time temperature dependent elastic viscoplastic constitutive theories which are based on the unified approach werre assessed. This class of constitutive theories is characterized by the use of kinetic equations and internal variables with appropriate evolutionary equations for treating all aspects of inelastic deformation including plasticity, creep, and stress relaxation. More than 10 such unified theories which are shown to satisfy the uniqueness and stability criteria imposed by Drucker's postulate and Ponter's inequalities are identified. The theories are compared for the types of flow law, kinetic equation, evolutionary equation of the internal variables, and treatment of temperature dependence. The similarities and differences of these theories are outlined in terms of mathematical formulations and illustrated by comparisons of theoretical calculations with experimental results which include monotonic stress-strain curves, cyclic hysteresis loops, creep and stress relaxation rates, and thermomechanical loops. Numerical methods used for integrating these stiff time temperature dependent constitutive equations are reviewed.

Chan, K. S.↗

Compatibility Testing of Polymeric Materials for the Urine Processor Assembly (UPA) of International Space Station (ISS)

In the International Space Station (ISS), astronauts will convert urine into potable water with the Urine Processor Assembly (UPA) by a distillation process. The urine is pre-treated, containing flush water and stabilizers. About 2.5% solids in the urine are concentrated up to 16% brine through distillation. Dynamic mechanical analysis (DMA) in the stress relaxation mode was primarily used to test 15 polymeric UPA materials for compatibility with the pre-treated and brine solutions. There were concerns that chromium trioxide (CrO3), a stabilizer not in the original pre-treat formulation for similar compatibility testing in 2000, could have an adverse effect on these polymers. DMA testing is partially complete for polymeric material samples immersed in the two solutions at room temperature for as long as 200 days. By comparing each material (conditioned and virgin), the stress relaxation modulus (E) was determined for short-term use and predicted for as long as a 10-year use in space. Such a delta E showed a decrease of as much as 79% for a Nylon material, but an increase as much as 454% for a polysulfone material, with increasing immersion time.

Wingard, Charles D.↗

Understanding failure in austenitic steels: Key considerations for molten salt storage in CSP applications

Owing to their excellent properties, austenitic stainless steels are extensively used in boilers, furnaces, molten salt tanks, and other applications that are subjected to extreme mechanical loads and high-temperature conditions. Their high corrosion and creep resistance make them suitable for high-temperature operating environments. Additionally, good fatigue resistance and favorable mechanical and visual properties are essential. However, the premature failure of several components at elevated temperatures has been previously reported. Although the failure analysis of components in service is complex, processes such as cold work and welding have been identified as contributing factors to the performance degradation of these steels. This study aims to analyze the various documented failure modes and mechanisms in austenitic steels, including creep, cracking, stress relaxation cracking, and fatigue, to better understand the multi-objective design requirements for these alloys as structural materials for high-temperature molten salt tanks in Concentrating Solar Power (CSP) plants. Stabilized austenitic grades, such as AISI 347H, demonstrate superior resistance to creep and corrosion-related degradation when compared to non-stabilized grades like AISI 316L at temperatures relevant to concentrated solar power (CSP) applications. In contrast, nickel-based alloys offer enhanced corrosion resistance, albeit at a higher cost. This review underscores that creep, stress relaxation cracking, and thermo-mechanical fatigue are the predominant long-term failure risks in CSP hot tanks.

14 SOLAR ENERGY↗

Alignment of morphology during high spatial frequency periodic structure formation in GaAs

The interaction among multiple intense ultrashort laser pulses and solids is known to provide a regular nanoscale surface corrugation. A coupled mechanism has been identified that operates in a specific range of fluences in GaAs that exhibits transient loss of the imaginary part of the dielectric function and Χ 2 , which produces a unique corrugation known as high spatial frequency laser induced periodic surface structures (HSFL). The final structures have 180 nm periods, and their alignment perpendicular to the laser polarization is first observed in an intermediate morphology with correlation distances of 150±40 nm. Quantum molecular dynamics simulations suggest that HSFL self-assembly is initiated when the intense laser field softens the interatomic binding potential, which leads to an ultrafast generation of point defects. The morphological evolution begins as self-interstitial diffusion, driven by stress relaxation, to the surface producing 1–2 nm tall islands. An ab initio calculation of excited electron concentration combined with a Drude-Lorentz model of the excited GaAs dielectric function is used to determine that the conditions for SPP coupling at HSFL formation fluences are both satisfied and occur at wavelengths that are imprinted into the observed surface morphologies. The evolution of these morphologies is reported on as the interplay between surface plasmon polaritons that localize defect generation within the structures present on the previous laser exposure and stress relaxation driven defect diffusion.

36 MATERIALS SCIENCE↗

Nonequilibrium material effects on the behavior of polymeric composite matrices and their related composites

The effects of physical aging on the material properties of some linear and network macromolecular glasses are discussed. The free volume concept is used to describe this behavior. The effect of physical aging on properties of some uniaxial graphite/fiber epoxy resin composites is investigated using stress relaxation in both tensile and flexural modes. The matrix polymers used were resins both of which are based on a 4,4-methylenedianiline derivative of epichlorohydrin with diamino diphenyl sulfone (DDS) as the curing agent. The matrix resin, as used in the practical application in composites, not fully cured and the glass transition of the network was dependent on the curing schedule. The physical aging of the bulk crosslinked epoxy was found to depend on the annealing temperature, and the T sub g of the resin. The physical aging of the composite, monitored by the stress relaxation method, was found to be dependent on the testing direction.

Wilkes, G. L.↗

Periodic surface structure bifurcation induced by ultrafast laser generated point defect diffusion in GaAs

The formation of high spatial frequency laser induced periodic surface structures (HSFL) with period <0.3 λ in GaAs after irradiation with femtosecond laser pulses in air is studied. We have identified a point defect generation mechanism that operates in a specific range of fluences in semiconductors between the band-gap closure and ultrafast-melt thresholds that produces vacancy/interstitial pairs. Stress relaxation, via diffusing defects, forms the 350–400 nm tall and ∼90 nm wide structures through a bifurcation process of lower spatial frequency surface structures. The resulting HSFL are predominately epitaxial single crystals and retain the original GaAs stoichiometry.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Microstructure characterization and elastic-plastic self-consistent simulation studies of anisotropic deformation of β -tin

Uniaxial compression tests of 99.9% pure polycrystalline $β$-tin (Sn) were conducted at various strain rates (10 -3 /s, 10 -1 /s and 1/s) and temperatures (294 K and 193 K) to understand the effects of these variables on the stress–strain response, microstructure evolution, and stress relaxation behavior. Multiple Sn specimens were subjected to complex compressive loading/unloading/reloading paths at different strain rates. Specimens initially compressed at higher strain rates showed strain rate-dependent texture evolution and more pronounced relaxation upon reloading, as compared to those pre-strained at lower rates at room temperature (RT). Compression tests conducted at low temperature (193 K) revealed increased strength, similar to the enhanced strength observed when the strain rate was increased at RT. Neutron diffraction was employed to characterize the initial and final bulk textures of the RT specimens. Electron backscatter diffraction was utilized to examine the crystallographic grain orientation and morphology, thereby identifying the signatures of dislocation-mediated deformation, grain refinement, recrystallization, and twinning behaviors. Elastic-plastic self-consistent simulations were performed to investigate the deformation modes responsible for the strain rate-dependent macroscopic stress–strain response and texture evolution. Effects of crystallographic orientation on stress relaxation behavior was also examined. In conclusion, the model predictions are in reasonable agreement with experimental observations.

36 MATERIALS SCIENCE↗