SEARCH · Search NASA

Results for “Screw”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Z-2 Threaded Insert Design and Testing Abstract

The Z-2 Prototype Planetary Extravehicular Space Suit Assembly is a continuation of NASA's Z series of spacesuits. The Z-2 is another step in the NASA's technology development roadmap leading to human exploration of the Martian surface. To meet a more challenging set of requirements than previous suit systems standard design features, such as threaded inserts, have been re-analyzed and improved. NASA's Z-2 prototype space suit contains several components fabricated from an advanced hybrid composite laminate consisting of IM10 carbon fiber and fiber glass. One requirement NASA levied on the suit composites was the ability to have removable, replaceable helicoil inserts to which other suit components would be fastened. An approach utilizing bonded in inserts with helicoils inside of them was implemented. The design of the interface flanges of the composites allowed some of the inserts to be a "T" style insert that was installed through the entire thickness of the laminate. The flange portion of the insert provides a mechanical lock as a redundancy to the adhesive aiding in the pullout load that the insert can withstand. In some locations it was not possible to utilize at "T" style insert and a blind insert was used instead. These inserts rely completely on the bond strength of the adhesive to resist pullout. It was determined during the design of the suit that the inserts did not need to withstand loads induced from pressure cycling but instead tension induced from torqueing the screws to bolt on hardware which creates a much higher stress on them. Bolt tension is determined by dividing the torque on the screw by a k value multiplied by the thread diameter of the bolt. The k value is a factor that accounts for friction in the system. A common value used for k for a non-lubricated screw is 0.2. The k value can go down by as much as 0.1 if the screw is lubricated which means for the same torque, a much larger tension could be placed on the bolt and insert. This paper summarizes testing that was performed to determine a k value for helicoil inserts in the Z2 suit and how the insert design was modified to resist a higher pull out tension.

Rhodes, RIchard↗

NASA NTRS2016

Z-2 Threaded Insert Design and Testing

NASA's Z-2 prototype space suit contains several components fabricated from an advanced hybrid composite laminate consisting of IM10 carbon fiber and fiber glass. One requirement was to have removable, replaceable helicoil inserts to which other suit components would be fastened. An approach utilizing bonded in inserts with helicoils inside of them was implemented. During initial assembly, cracking sounds were heard followed by the lifting of one of the blind inserts out of its hole when the screws were torqued. A failure investigation was initiated to understand the mechanism of the failure. Ultimately, it was determined that the pre-tension caused by torqueing the fasteners is a much larger force than induced from the pressure loads of the suit which was not considered in the insert design. Bolt tension is determined by dividing the torque on the screw by a k value multiplied by the thread diameter of the bolt. The k value is a factor that accounts for friction in the system. A common value used for k for a non-lubricated screw is 0.2. The k value can go down by as much as 0.1 if the screw is lubricated which means for the same torque, a much larger tension could be placed on the bolt and insert. This paper summarizes the failure investigation that was performed to identify the root cause of the suit failure and details how the insert design was modified to resist a higher pull out tension.

Ross, Amy↗

DOE OSTI2021

Target unit with ceramic capsule for producing cu-67 radioisotope

A target unit for producing Cu67 radioisotope is described herein, and comprises a cage body releasably coupled to a screw-on cap; and a ceramic capsule containing a solid Zn68 target ingot and having one open end and one closed end and defining an interior chamber for the target ingot. The ceramic capsule is releasably contained between the cage body and the screw-on cap with a lid disposed on the open end of the capsule and a washer positioned between the lid and the screw-on cap. The screw-on cap and the washer provide a water-tight seal between the lid and the capsule. The interior of the capsule is in intimate physical contact with the target ingot; and the Zn68 of the target ingot is free of traces of residual oxygen that interfere with contact of the Zn68 to the capsule.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

DOE OSTI2023

Patterns in interactions of variably acetylated xylans with hydrophobic cellulose surfaces

The recalcitrance of plant cell wall lignocellulosic biomass to deconstruction is a major hurdle to sustainable biofuel/bioproduct economy. A multitude of interactions stabilize lignocellulosic biomass structure. Among these, tight packing of hemicellulose-cellulose is partly responsible for biomass recalcitrance. Here, unrestrained molecular dynamics simulations are employed to understand the influence of the nature and pattern of naturally-occuring acetyl decorations of the xylan backbone on interactions with the (100) hydrophobic cellulose surface. Periodically O2-acetylated xylan (2AcX) assume twofold helical screw conformations that are stabilized by a combination of multiple hydrophobic contacts and hydrogen bonds with the hydrophobic cellulose surface. In contrast, acetylation at the O3 position in xylan obstructs interactions, thereby adopting threefold helical screw conformations that potentially preferably interact with lignin rather than cellulose. Fully acetylated xylan desorbs from the surface implying a minimum number of unsubstituted residues on the xylan backbone is required for interaction with the surface. Here, the substituted residues must form ~ 20% fewer contacts than the unsubstituted residues to sustain stable twofold helical screw xylan conformations on the cellulose surface. Thus, specific roles of macromolecular conformations of cellulose and hemicellulose in influencing the supramolecular interactions and function of plant cell walls have been determined.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2026

A theoretical study of solid solution strengthening in the refractory medium entropy alloy Nb 45 Ta 25 Ti 15 Hf 15

The refractory medium-entropy alloy (RMEA) Nb 45 Ta 25 Ti 15 Hf 15 exhibits exceptional tensile ductility and fracture toughness at ambient temperature, but its engineering applications are limited by a lack of high temperature strength. Using a machine-learning interatomic potential (MLIP) with near-density functional theory (DFT) accuracy, we conducted molecular dynamics (MD) and statics simulations of the behavior of dislocations with both screw and edge characters. We also analyze experimentally measured yield strengths using the Rao-Suzuki model and the Maresca-Curtin model modified to include a temperature-dependent shear modulus and a bulk modulus-dependent misfit volume, thereby uncovering the mechanisms underlying the yielding of this RMEA. Compared with the published experimental yield strength, the models parameterized by the MLIP effectively reproduce the experimental results over a wide temperature range. The models and MD simulations indicate that yielding is governed by screw dislocations, with dipole dragging as the dominant mechanism. In MD simulations, we observed a potential softening mechanism not considered by the Rao-Suzuki screw model: slow migration of interstitial jogs along the dislocation core, which could lead to the annihilation of vacancy and interstitial jog pairs by their combination.

BCC complex concentrated alloys↗

DOE OSTI2022

Phase-field dislocation modeling of cross-slip

The phase-field dislocation dynamics (PFDD) model is extended to simulate cross-slip in body-centered cubic materials. The model makes use of a non-orthogonal, body-centered cubic numerical grid such that all calculable points lie on dislocation glide planes. We demonstrate that the advanced PFDD model predicts a low-energy, non-planar core for screw dislocations and a planar core for edge dislocations. These core differences result in screw-edge character dependence in the critical stress to initiate glide and dislocation drag coefficients. Finally, we show that this model can be used to study the propensity of screw dislocations to cross-slip around or transmit through a coherent, crystallographic obstacle, depending on obstacle strength.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Development of a new control rod drive mechanism design for the ISU AGN-201M reactor

The Aerojet General Nucleonics (AGN) model 201-Modified, known as the AGN-201M reactor, plays an essential role in the educational and research activities at Idaho State University (ISU). The ISU AGN-201M's original Control Rod Drive Mechanism (CRDM) has been in operation for more than fifty years with no large-scale redesigns. The CRDM is required to eject the fuel rods within one second during a SCRAM event (also known as a 'reactor trip') and adjust the control rods' insertion speed, and keeps the rod insertion sequence correct. The existing control rod drive mechanisms meet these criteria but experience a few concerns due to aging. Concerns include complex maintenance and costly repairs for old electromechanical components, rod position feedback errors, and the impediment of the plate during a SCRAM due to binding of the lead screws of the existing mechanism. During a binding event, the drive mechanism becomes locked, preventing the control rod's magnetic plate from moving in or out under the reactor's normal and emergency operating conditions. Although, the binding has no effect on the ability of the rod to exit the core during the SCRAM. To counteract the concerns and issues with the current CRDM, a new design has been proposed using newer components and a simplified design. The new design utilizes more advanced electric and mechanical components that are commercially available. The new CRDM system is divided into four main aspects: (1) control rod movement design (motor, lead screw, guide rods), (2) control rod ejection (springs, electromagnet), (3) control rod position and feedback (position transducer, microswitches), and (4) material selection and structural analysis. The new design aims to reduce the overall complexity and probability of failure to improve the reactor's overall reliability. With proper material selection and improved structural design, the new drives are lighter with little to no change in structural integrity. The new control rod drive mechanism eliminates binding scenarios by using a single lead screw and implementing additional guide rods. An advanced linear position sensor and microswitches replace the existing and aging synchro system for accurate rod position feedback resulting in better reactivity control. The new design meets the reactor's operational limits by having an average reactivity insertion of 0.065% Δk/k per second, which corresponds to a total control rod insertion time of 19.23 s, while the control rod's ejection time remains less than one second during a SCRAM event. The new design ensures the reactor's long-term viability for educational and research activities by increasing the reliability and safety of operation for years to come.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2025

Fiber orientation and porosity in large-format extrusion process: The role of processing parameters

Controlling fiber orientation and porosity in short-fiber thermoplastic composites is important for enhancing mechanical, electrical and thermal properties in large-format additive manufacturing. This study employs a factorial design of experiments (DoE) to assess the effects of nozzle diameter (5.08 mm–10.16 mm), temperature (230–250 °C), and extruder screw speed (150–280 rpm) on flow rate, shear rate, porosity, fiber orientation, fiber length and tensile strength in 20 % carbon fiber-filled acrylonitrile butadiene styrene. ANOVA results show that screw speed significantly impacts flow rate, while nozzle diameter and temperature have lesser effects. Shear rate increases with smaller nozzles and higher speeds. Porosity decreases from 5.58 % with a 10.16 mm nozzle to 3.11 % with a 5.08 mm nozzle at 150 rpm due to increased shear rates, which induce shear thinning, reducing viscosity and facilitating gas escape. Larger nozzles (10.16 mm) produce larger, more heterogeneous pores, while smaller nozzles (5.08 mm) yield smaller, uniform pores. Beads produced with the 5.08 mm nozzle exhibit longer fiber lengths due to reduced residence time, lower shear stress, and better alignment. Fiber orientation improves with smaller nozzles due to higher shear rates but decreases with higher screw speeds (280 rpm) due to shorter residence times. The highest fiber alignment (A xx ∼ 0.65) and low porosity (∼3%) were achieved with a 5.08 mm nozzle at 150 rpm, while equivalent additive manufacturing-compression molding samples exhibited better tensile strength (∼93 MPa) under these conditions. In conclusion, these findings emphasize the importance of optimizing processing parameters to enhance fiber alignment and reduce porosity for improved mechanical performance.

Design of experiments↗

DOE OSTI2024

Polarization near dislocation cores in SrTiO 3 single crystals: The role of flexoelectricity

Spontaneous polarization as large as ~28 μC/cm 2 was recently observed around the dislocation cores in non-polar SrTiO 3 bulk crystals, and its origin was attributed to the flexoelectric effect, i.e., polarization induced by strain gradients. However, the roles of flexoelectricity, relative to other electromechanical contributions, and the nature of dislocations, i.e., edge vs screw dislocations in the induced polarization, are not well understood. In this work, we study the role of flexoelectricity in inducing polarization around three types of dislocation cores in SrTiO 3 : b= a(100) edge dislocation, b= a(110) edge dislocation, and b= a(010) screw dislocation, where b is the Burgers vector. For the edge dislocations, polarization can be induced by electrostriction alone, while flexoelectricity is essential for stabilizing the symmetric polarization pattern. The shear component of the flexoelectric tensor has a dominant effect on the magnitude and spatial distribution of the flexoelectric polarization. In contrast, no polarization is induced around the b= a(010) screw dislocation through either electrostriction or flexoelectricity. Finally, our findings provide an in-depth understanding of the role of flexoelectricity in inducing polarization around dislocation cores and offer insights into the defect engineering of dielectric/ferroelectric materials.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Transitions in the morphology and critical stresses of gliding dislocations in multiprincipal element alloys

Refractory multiprincipal element alloys (MPEAs) are promising material candidates for high-temperature, high-strength applications. However, their deformation mechanisms, particularly at the dislocation scale, are unusual compared to those of conventional alloys, making it challenging to understand the origin of their high strength. Here, using an atomistically informed phase-field dislocation dynamics model, we study transitions in the morphology and critical stresses of long gliding screw dislocations over extended distances in a refractory MPEA. The model MPEA crystal accounts for the atomic-scale fluctuations in chemical composition across the glide planes via spatially correlated lattice energies and for the differences in glide resistances between screw and edge dislocations of unit length. Here, we show that the dislocation moves in a stop-start motion, alternating between wavy morphology in free flight and nearly recovered straight screw orientation in full arrest. The periods of wavy glide are due to variable kink-pair formation and migration rates along the length, where portions with higher rates glide more quickly. The critical stress to initiate motion corresponds to the stress required to form and migrate a kink pair at the weakest region along the length of the dislocation. Heterogeneity in lattice energy leads to variability in the local stress-strain response and to a strain hardening-like response, in which the critical stress to reactivate glide increases with glide distance. Statistical assessment of hundreds of realizations of dislocations indicates that the amount of hardening directly scales with the dispersion in underlying lattice energy.

3-dimensional systems↗

DOE OSTI2024

Performance Testing of an Integrated Magnetic Power Take-Off

A wave energy converter (WEC) and the power take-off (PTO) generator system can be represented by using a mass-spring-dampener model. By incorporating a negative stiffness spring within the PTO, the overall stiffness of the PTO can be lowered allowing the impedance of the PTO to be more closely matched with the WEC. By designing for impedance matching the WEC can greatly enhance its power generation capability. This project has involved the design, fabrication and testing of a new type of linear-stroke length and rotary stroke length adjustable negative stiffness magnetic springs for use within a wave energy converter (WEC). The magnetic springs were studied by using 3-D finite element analysis with the objective of creating high energy density and a long linear stroke length. After the construction and testing of both a proof-of-principle adjustable linear and rotary magnetic spring prototype the rotary (torsional) magnetic spring was selected for scaling up analysis. The selected scaled-up proof-of-principle magnetic spring had a peak torque of 850 Nm with a ±45 degree stroke length. By translating the inner rotor relative to the outer rotor, the stiffness could be adjusted to be either negative or positive stiffness. During this project a magnetic lead screw was also studied, and it was shown that by combining the magnetic lead screw with a linearly translating magnetic spring a very long rotary stroke length could be attained. However, as the magnetic lead screw increased complexity and reduced overall energy density relative to a rotary (torsional) spring, this design approach was not further pursed. Dynamometer testing of the variable stiffness magnetic springs was first completed by Portland State University and following this the magnetic spring performance was independently verified by Sandia National Laboratory (Sandia). A WEC analysis when using a variable stiffness magnetic spring was completed by using the WecOptTool. WecOptTool is an open-source WEC optimization software developed by Sandia that supports efficient power take-off (PTO) and control optimization. Wave condition data from the Oregon PacWave test-site was used in this study. The analysis showed that a WEC with a tunable stiffness value could consistently achieve about 80% of its maximum theoretical power production. The use of a tunable stiffness WEC, rather than zero-stiffness or a constant stiffness WEC was also shown to lead to a smaller maximum PTO force requirement. The variable stiffness magnetic spring was integrated into an experimental WEC developed by Sandia, called a Wave-Bot. Sandia successfully completed water-tank testing of the Wave-Bot at the Navy’s Carderock, Maryland, wave-basin test site. The wave-basin testing helped to experimentally demonstrate the operating capabilities and increased power generation capability of a WEC containing an integrated variable stiffness magnetic spring. A WEC capacity factor analysis was also completed. The capacity factor was defined as the ratio of annual average WEC generator power to the maximum (RMS) generated power. This capacity factor provided a means of identifying the ratio of potential revenue to cost. It was calculated that if a tunable variable stiffness magnetic spring has RMS constraints it could operate with a capacity factor above 30%. This is comparable to a wind turbine’s capacity factor.

16 TIDAL AND WAVE POWER↗

NASA NTRS1972

Trends in mechanical fasteners

Some of the specialty fasteners which are enjoying increasing usage are: thread rolling screws, self drilling and tapping screws, locking screws, tamperproof fasteners, and flanged bolts and nuts. The development of an optimum metric fastener system is recommended for future fastener manufacturing.

Levy, J. B.↗

NASA NTRS1978

Floating nut for spacecraft application

Nut overcomes mechanical mismatch from accumulated tolerances and maintains assembly even if mounting screw loosens. Nut and screws can be painted with bonding agent to insure lock. If assemblies are removed frequently, nut and screws can be made of steel to reduce wear and tear on threads and risk of faulty threads.

Ell, L. J.↗

NASA NTRS1978

Rotary leveling base platform

A leveling apparatus for the precise adjustment of a scientific instrument is reported. A base member is provided having a hollow cylindrical shape. A table for supporting the instrument rests on the base and has a shaft portion extending below the table. The upper portion of the shaft fits tightly into the hollow portion of the base member whereas the lower portion of the shaft is machined to fit loosely. The lower portion of the shaft is provided with a groove. Adjusting screws are threaded through the hollow cylindrical portion and are adapted to enter the groove. By adjusting the screws, the lower portion of the shaft is moved in a vertical plane since the shaft is loosely fitted into the cylinder. The upper portion of the shaft which is tightly fitted into the upper end of the cylinder causes the cylinder to deform slightly providing a fulcrum point which allows the table to be leveled in response to the adjustment of the adjusting screws.

Delaplaine, R. W.↗

NASA NTRS1986

Ejection Mechanism for Circuit Boards

Damage to connectors reduced and special tools not needed. Clockwise rotation of screw tightens wedges against mounting body and right heat sink. Counterclockwise rotation of screw drives bottom wedge downward and jacking ring upward, pulling pins away from mating connector. Screw in mechanism turned to produce jacking force that disengages board from mating connector. Force parallel to connector pins do not bend or brake. When disengaged, board protrudes from assembly and readily grasped by operator.

Houff, T. L.↗

NASA NTRS1986

Plastic deformation of a magnesium oxide 001-plane surface produced by cavitation

An investigation was conducted to examine plastic deformation of a cleaved single-crystal magnesium oxide 001-plane surface exposed to cavitation. Cavitation damage experiments were carried out in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (2 mm) to the surface of the cleaved specimen. The dislocation-etch-pit patterns induced by cavitation were examined and compared with that of microhardness indentations. The results revealed that dislocation-etch-pit patterns around hardness indentations contain both screw and edge dislocations, while the etch-pit patterns on the surface exposed to cavitation contain only screw dislocations. During cavitation, deformation occurred in a thin surface layer, accompanied by work-hardening of the ceramic. The row of screw dislocations underwent a stable growth, which was analyzed crystallographically.

Hattori, S.↗

NASA NTRS1991

Alignment positioning mechanism

An alignment positioning mechanism for correcting and compensating for misalignment of structures to be coupled is disclosed. The mechanism comprises a power screw with a base portion and a threaded shank portion. A mounting fixture is provided for rigidly coupling said base portion to the mounting interface of a supporting structure with the axis of the screw perpendicular thereto. A traveling ball nut threaded on the power screw is formed with an external annular arcuate surface configured in the form of a spherical segment and enclosed by a ball nut housing with a conforming arcuate surface for permitting gimballed motion thereon. The ball nut housing is provided with a mounting surface which is positionable in cooperable engagement with the mounting interface of a primary structure to be coupled to the supporting structure. Cooperative means are provided on the ball nut and ball nut housing, respectively, for positioning the ball nut and ball nut housing in relative gimballed position within a predetermined range of relative angular relationship whereby severe structural stresses due to unequal loadings and undesirable bending moments on the mechanism are avoided.

Fantasia, Peter M.↗

NASA NTRS1924

Jet propulsion for airplanes

This report is a description of a method of propelling airplanes by the reaction of jet propulsion. Air is compressed and mixed with fuel in a combustion chamber, where the mixture burns at constant pressure. The combustion products issue through a nozzle, and the reaction of that of the motor-driven air screw. The computations are outlined and the results given by tables and curves. The relative fuel consumption and weight of machinery for the jet, decrease as the flying speed increases; but at 250 miles per hour the jet would still take about four times as much fuel per thrust horsepower-hour as the air screw, and the power plant would be heavier and much more complicated. Propulsion by the reaction of a simple jet can not compete with air screw propulsion at such flying speeds as are now in prospect.

Buckingham, Edgar↗