Search NASA⌕ Search

SEARCH · Search NASA

Results for “Si Anode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Pouch cells with 15% silicon calendar-aged for 4 years

Small amounts of high-capacity silicon-based materials are already used in the anode of commercial Li-ion batteries, helping increase their energy density. Despite their remarkable storage capability, silicon continu-ously reacts with the electrolyte, accelerating time-dependent cell performance fade. Nevertheless, very limited information is available on the specific consequences of this reactivity for the calendar aging of Li-ion cells. Here, we analyze aging effects on 450 mAh pouch cells containing 15 wt% of Si (and 73 wt% graphite) after storage at 21 °C for four years. We show that severe losses of Si capacity occurred due to particle isolation when cells were stored at high states of charge (SOC), but not when cells were fully discharged prior to storage. Impedance rise was also significantly higher when cells were kept at high SOCs and was mostly due to phenomena taking place at the cathode; the continuous electrolyte reduction at the anode did not lead to a major increase in bulk electrode resistance. A series of post-test characterization provided additional information on the effects of time and SOC on the calendar aging of Si-containing cells. In conclusion, our study highlights the many challenges posed by Si during calendar aging and can inform future studies in the field.

25 ENERGY STORAGE↗
DOE OSTI2023

On-Wafer Wide-Pore Anodic Aluminum Oxide

Anodized aluminum oxide (AAO) has been used as nanotemplates for nanomaterials and nanodevice fabrications. Microfabrication techniques are attracting attention for nanodevice synthesis. However, AAO requires a microfabrication-compatible substrate due to its brittleness. While there are studies that already show AAO on compatible substrates, the pore sizes may not be applicable for multicomponent nanodevices. In this study, wide pore AAOs with ohmic bottom contacts are fabricated on 76 mm Si wafers. Sputtering was used to deposit Al along with supporting layers to achieve this goal. A quiescent electropolishing technique was used to smooth the surface of Al. Standard photolithography was used to define the active area on the Al for anodization. Then 195 V two-step anodization was performed to fabricate wide pore AAOs with pore diameters ranging from 130 ± 32 nm to 400 ± 31 nm with interpore distance of 480 ± 47 nm. Furthermore, it also showed that the ordering of the pores depended on the current density over the more conventional anodization time.

25 ENERGY STORAGE↗
DOE OSTI2020

Scalable synthesis of nanoporous silicon microparticles for highly cyclable lithium-ion batteries

Nanoporous silicon is a promising anode material for high energy density batteries due to its high cycling stability and high tap density compared to other nanostructured anode materials. However, the high cost of synthesis and low yield of nanoporous silicon limit its practical application. Here, we develop a scalable, low-cost top-down process of controlled oxidation of Mg 2 Si in the air, followed by HCl removal of MgO to generate nanoporous silicon without the use of HF. By controlling the synthesis conditions, the oxygen content, grain size and yield of the porous silicon are simultaneously optimized from commercial standpoints. In situ environmental transmission electron microscopy reveals the reaction mechanism; the Mg 2 Si microparticle reacts with O 2 to form MgO and Si, while preventing SiO 2 formation. Owing to the low oxygen content and microscale secondary structure, the nanoporous silicon delivers a higher initial reversible capacity and initial Coulombic efficiency compared to commercial Si nanoparticles (3,033 mAh/g vs. 2,418 mAh/g, 84.3% vs. 73.1%). Synthesis is highly scalable, and a yield of 90.4% is achieved for the porous Si nanostructure with the capability to make an excess of 10 g per batch. Our synthetic nanoporous silicon is promising for practical applications in next generation lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Environmental stability of additively manufactured siliconized silicon carbide for applications in hybrid energy systems

A key consideration for the successful operation of hybrid energy systems will be the environmental stability of materials used for their construction, particularly when experiencing service environments containing water vapor at high temperatures. Here, we report results from the characterization of siliconized silicon carbide (Si-SiC) prepared via binder jet additive manufacturing and reactive silicon melt infiltration after being exposed to environments representative of those in solid oxide fuel cell (SOFC) anodes, and to exhaust gases inside a microturbine operating on natural gas. In both cases, it was found that oxide scales formed on the surface and that these scales were dense, continuous, and well-bonded to the substrates, although there was evidence of transverse and longitudinal cracking most likely as a result of mismatches in the thermal expansion of the scale and the substrate. Measured values of the thickness of the oxide scale were compared to those predicted by parabolic oxidation kinetics of silicon, but the potential effects of silica volatilization induced by water vapor, and silica reduction when exposed to hydrogen are discussed. The overall results showed that the oxide scale is expected to be protective under the conditions of hybrid power generation systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electrochemical Reactivity and Passivation of Silicon Thin-Film Electrodes in Organic Carbonate Electrolytes

This work focuses on the mechanisms of interfacial processes at the surface of amorphous silicon thin-film electrodes in organic carbonate electrolytes to unveil the origins of the inherent nonpassivating behavior of silicon anodes in Li-ion batteries. Attenuated total reflection Fourier-transform infrared spectroscopy, X-ray absorption spectroscopy, and infrared near-field scanning optical microscopy were used to investigate the formation, evolution, and chemical composition of the surface layer formed on Si upon cycling. Herein, we found that the chemical composition and thickness of the solid/electrolyte interphase (SEI) layer continuously change during the charging/discharging cycles. This SEI layer “breathing” effect is directly related to the formation of lithium ethylene dicarbonate (LiEDC) and LiPF6 salt decomposition products during silicon lithiation and their subsequent disappearance upon delithiation. Furthermore, the detected appearance and disappearance of LiEDC and LiPF6 decomposition compounds in the SEI layer are directly linked with the observed interfacial instability and poor passivating behavior of the silicon anode.

25 ENERGY STORAGE↗
DOE OSTI2022

Initial tests of Accelerator Mass Spectrometry with the Argonne Gas-Filled Analyzer and the commissioning of the MONICA detector

As the scope of Accelerator Mass Spectrometry (AMS) expands, there is an increased need to extend the capability of isobaric separation to the medium-heavy mass region. Existing AMS facilities are limited in their ability to separate radioactive nuclei in the A = 100–200 range of interest from their neighboring stable isobars, as such measurements require higher energies than available in most facilities. ATLAS is one of the highest energy system used for AMS based experiments and has enabled isobaric discrimination for medium to heavy nuclides, notably via the Gas-Filled Magnet technique. Further, a preparatory experiment performed in November, 2019, successfully demonstrated isobaric separation of 92 Zr- 92 Mo using the Argonne Gas-Filled Analyzer (AGFA) with high magnetic rigidity. Since that time, MONICA, an eight-anode ionization chamber that measures both energy loss and position with two sets of split anodes, has been developed to aid in AMS experiments at AGFA and has undergone four commissioning runs at the Nuclear Science Laboratory at the University of Notre Dame utilizing Si, Fe/Ni, and Mn beams. This report presents the AGFA AMS run (November 2019) and the subsequent commissioning runs of the MONICA detector, including preliminary measurements on the long-lived isotopes 39 Ar (268 y) and for the first time on 42 Ar (33 y).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Communication—Functional Conductive Polymer Binder for Practical Si-Based Electrodes

Multifunctional conductive binders represent an emerging class of polymer materials to address inherent challenges of Si electrodes for high capacity lithium-ion batteries. Advanced binders with oriented functionalities are greatly desired to facilitate the battery chemistry. We here report stable capacity cycling of a practical composite anode comprising industrial available SiO x (>60 wt%), carbon materials and a conductive polymer binder—poly(9,9-dioctylfluorene- co -fluorenonecomethylbenzoic ester) (PFM). This multifunctional polymer functions as both an interface modifier and an electrode binder for high-performing SiO x composite electrodes. The viability of multifunctional conductive polymer binders was further validated in a practical full cell.

25 ENERGY STORAGE↗
DOE OSTI2022

Bioinspired mechanically interlocking holey graphene@SiO 2 anode

Mechanically interlocking structures that can enhance adhesion at the interface and regulate the stress distribution have been widely observed in biological systems. Inspired by the biological structures in the wings of beetles, we synthesized a holey graphene@SiO 2 anode with strong mechanical interlocking, characterized it electrochemically, and explained its performance by finite element analysis and density functional calculations. The mechanically interlocking structure enhances lithium-ion (Li + ) storage by transmitting the strain from SiO 2 to the holey graphene and by a mechano-electrochemical coupling effect. The interlocking fit hinders the abscission of SiO 2 and the distinctive structure reduces the stress and strain of SiO 2 during (de)lithiation. The positive mechano-electrochemical coupling effect preserves the amount of electrochemically active phase (Li x Si) during cycles and facilitates Li + diffusion. Therefore, the capacity shows only a slight attenuation after 8000 cycles (cycling stability), and the specific capacity is ~1200 mA h g –1 at 5 A/g (rate-performance). This study furnishes a novel way to design high-performance Li + /Na + /K + /Al 3+ anodes with large volume expansion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Prelithiation of Lithium Peroxide for Silicon Anode: Achieving a High Activation Rate

The use of lithium peroxide (Li2O2) as a cost-effective low-weight prelithiation cathode additive was successfully demonstrated. Through a series of studies on the chemical stability of Li2O2 and the activation process of Li2O2 on the cathode, we revealed that Li2O2 is more compatible with conventional electrolyte and cathode laminate slurry than lithium oxide. Due to the significantlysmaller size of commercial Li2O2, it can beused directly as a cathode additive. Moreover, the activation of Li2O2 on the cathode leads to the impedance growthof the cathode possibly resulting from the release of dioxygen andevacuation of Li2O2 inside the cathode. Withthe introduction of a new Li2O2 spread-coatingtechnique on the cathode, the capacity loss was suppressed. Si||NMCfull cells using Li2O2 spread-coated cathodedemonstrated a highly promising activation rate of Li2O2 and significantly enhanced specific capacity and cyclingstability compared to the uncoated full cells.

cathode additive↗
DOE OSTI2020

SiO 2 Is Wasted Space in Single-Nanometer-Scale Silicon Nanoparticle-Based Composite Anodes for Li-Ion Electrochemical Energy Storage

The electrode processing conditions of silicon-based composite anodes play a pivotal role in the resulting interfacial chemical speciation and, thus, the electrochemical cycling behavior of the electrode. Systematically investigating how small chemical changes to the surface of the silicon nanoparticle (NP) affect larger, electrode-level properties is a strategy that will inform design principles to maximize electrode energy density and extend electrode lifetime. Here, we incorporate silicon nanoparticles (NPs) with an average diameter of 5.5 nm synthesized from the gas phase through a nonthermal plasma method into composite anode half-cell coin cells. We perform chemistry to functionalize the native hydride-terminated silicon NP surface with N-methylpyrrolidone (NMP) to improve slurry properties and reduce the silicon reactivity prior to composite electrode fabrication. We construct composite electrodes from these silicon NPs and observe an 86% capacity retention over 100 cycles at a rate of C/5, with an initial silicon specific capacity of 2600 mAh/g. We expose the same Si NPs to water that completely oxidizes these small-diameter NPs to SiO 2 and find that the SiO 2 NPs in the same electrode configuration exhibit no obvious lithium alloying capacity in the electrochemical potential range of lithium silicide alloy formation. As this result stands in contrast to existing literature, we provide a discussion on the origin of the discrepancies.

25 ENERGY STORAGE↗
DOE OSTI2022

Freestanding high-aspect-ratio gold masks for low-energy, phase-based x-ray microscopy

High-resolution, x-ray phase contrast microscopy, a key technique with promising potential in biomedical imaging and diagnostics, is based on narrow-slit high-aspect-ratio gold gratings. Here we present the development, fabrication details, and experimental testing of the freestanding 10 μm thick gold membrane masks with an array of 0.9–1.5 μm void slit apertures for a novel low-energy x-ray microscope. The overall mask size is 4 mm × 4 mm, with a grating pitch of 7.5 μm, 6.0–6.6 μm wide gold bars are supported by 3 μm wide crosslinks at 400 μm intervals. The fabrication process is based on gold electroplating into a silicon mold coated with various thin films to form a voltage barrier, plating base, and sacrificial layer, followed by the mold removal to obtain the freestanding gold membrane with void slit apertures. We discuss key aspects for the materials and processes, including gold structures homogeneity, residual stresses, and prevention of collapsing of the grid elements. We further demonstrate the possibility to obtain high-resolution, high contrast 2D images of biological samples using an incoherent, rotating anode x-ray tube.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Proton surface exchange kinetics of perovskite triple conducting thin films for protonic ceramic electrolysis cells: BaPr 0.9 Y 0.1 O 3–δ (BPY) vs. Ba 1–x Co 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3–δ (BCFZY)

Protonic ceramic electrolysis cells (PCECs) are an attractive green H 2 production technology, given their intermediate-temperature operating range and ability to produce dry H 2 . However, PCECs will benefit from development of more efficient and durable “triple conducting” anodes where steam is split, H incorporated, and oxygen evolved. In this work, we evaluated the kinetics of the steam-splitting/H incorporation reaction on BaPr 0.9 Y 0.1 O 3–δ (BPY) in comparison to the benchmark Ba 1–x Co 0.4 Fe 0.4 Z r0.1 Y 0.1 O 3–δ (BCFZY) composition, replacing most of the transition metal elements (Co, Fe, Zr) with the lanthanide Pr. We prepared geometrically well-defined perovskite BPY and BCFZY thin films by pulsed laser deposition and performed simultaneous optical transmission relaxation and electrical conductivity relaxation measurements at 400–500 °C in 0.21 atm O 2 during switching of the steam partial pressure to isolate and compare their proton surface exchange coefficients (k). The k values of BPY were comparable to those of BCFZY and more stable over time. According to angle-resolved XPS and STEM-EDS mapping of FIB cross-sections, the surface of BPY exhibited Ba enrichment, Pr deficiency, and Si contamination. In contrast, BCFZY exhibited Ba deficiency throughout, no obvious surface segregation, and less Si contamination. The Ba segregation on the BPY film appears to have promoted steam splitting/H incorporation kinetics even though the more basic surface reacted with the acidic environmental SiO x H y . Faster kinetics observed on stoichiometric BCFZY vs. Ba-deficient BCFZY confirmed the benefit of a high A-site Ba concentration. This result contrasts with most work on perovskites applied in solid oxide electrolysis cell anodes, in which A-site segregation is considered deleterious for surface reaction kinetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Petaloid-shaped ZnO coated carbon felt as a controllable host to construct hierarchical Li composite anode

Prestoring Li metal into the 3D host via thermal infusion strategy has been considered as an effective approach on suppressing Li dendrites growth of Li-metal anode during cycling. However, the fast Li infusing process generally induces uncontrollable and undesirable structures during the formation of composite Li metal anode. It is widely accepted that both physical and chemical interactions between the molten Li and the hosts provide driving forces for Li infusing into the host, but which one plays the dominant role has not been explored clearly. In this work, a 3D carbon felt coated by petaloid zinc oxide (CFZO) is designed as a controllable host for prestoring Li metal via thermal infusion method. It is revealed that the morphology induced physical driving force plays a more important role than the chemical reaction between ZnO and molten Li in the thermal infusion process. The physical driving force originates from the capillarity effect, depending on the roughness of the host according to Wenzel's model. An adjustable Li infusing process can be controlled to fabricate the Li composite electrode with a hierarchical structure (with dense Li-rich layer and porous Li-poor layer). The unique structure of the CFZO-Li not only provides enough spaces for Li deposition, but also disperses local current density to induce a uniform Li deposition behavior, thus Li dendrites can be suppressed effectively. As a result, CFZO-Li anode exhibits promising cycle stability when coupled with both Li-containing (LiNi 0.8 Co 0.15 Al 0.05 O 2 ) and Li-free (sulfur) cathodes.

25 ENERGY STORAGE↗
DOE OSTI2026

Two Artificial Leaf Architectures for Solar Formate Production From CO 2 and H 2 O

Sunlight-powered artificial leaves for the production of formate from CO 2 are an attractive route to solar fuels, yet existing solar formate devices remain low in performance, and their architecture and material choices are underexplored. Herein, we report the fabrication of two distinct fully integrated, self-standing solar formate device architectures and elucidate the underlying design principles and material selection strategies. The first architecture integrates a Si photocathode with a BiVO 4 photoanode and utilizes a highly active Pd catalyst for CO 2 reduction. It represents the first artificial leaf device comprising two photoelectrodes (excluding photovoltaic [PV]-biased electrodes) for effective formate production under single-beam illumination. The second architecture employs a dark cathode and a dark anode driven by a 4-junction perovskite solar cell and uses a highly stable Bi catalyst for CO 2 reduction. This device delivers a record-high formate production rate of 174 µmol h −1 with a remarkable solar-to-formate energy efficiency of 2% among all artificial leaf devices reported to date. Finally, these results demonstrate the feasibility and outline the design principles of both PV-free and PV-assisted device architectures in solar fuel production.

electrocatalysis↗
DOE OSTI2020

High-Throughput Exploration of Lithium-Alloy Protection Layers for High-Performance Lithium-Metal Batteries

To realize high specific capacity Li-metal batteries, a protection layer for the Li-metal anode is needed. We are carrying out combinatorial screening of Li-alloy thin films as the protection layer which can undergo significant lithiation with minimum change in volume and crystal structure. In this paper, we have fabricated lithium-free binary alloy thin film composition spreads of Co 1–x Sn x on Cu layers on Si substrates. The crystallinity of the thin films was tuned by varying the deposition temperature followed by electrochemical lithiation to form Li-alloy ternary thin films. Synchrotron diffraction is used as the main tool to investigate the crystallinity of the films before and after lithiation. Co 3 Sn 2 alloy thin films are found to exhibit significant lithium uptake capacity while maintaining its structural integrity, and are thus a good candidate of the Li-metal protection layer.

25 ENERGY STORAGE↗
DOE OSTI2021

Minimizing Cr-Evaporation from Balance Of Plant Components By Utilizing Cost-Effective Alumina-Forming Austenitic Steels

A solid oxide fuel cell (SOFC) is a clean and efficient energy conversion device. The development of intermediate-temperature SOFCs has made it preferable to use metallic interconnects (MICs) to greatly reduce the cost and significantly increase the efficiency compared to ceramic interconnect materials. However, gaseous chromium species will evaporate from the chromium-containing layer formed on the surface of commonly used MICs and balance of plant (BoP) components. Volatile chromium species have been shown to form solid deposits which poison the cathodes of SOFCs, causing drastic cell performance degradation and thereby limiting commercialization. In order to alleviate the Cr poisoning and achieve long-term high performance of SOFC stacks, various Al 2 O 3 -forming austenitic (AFA) stainless steels applied at different temperatures are evaluated in this project. Based on our Phase I results (500 h operation), it is shown that on the AFAs, an alumina-based protective layer forms under high temperature that is invulnerable to water vapor effects and suppresses the diffusion of chromium and manganese which can prevent the generation of spinels on the alloy surface. Therefore, 310S, OC4 and OC5 at 800 °C and 625, OC11 and OC11LZ at 900 °C are selected to be tested in the Phase II long-term operation. From the results, we find that besides the lower Cr evaporation rates and better oxidation resistance of AFAs than benchmark alloys after short-term (500 h) operation, AFAs also possess the sturdy and compact alumina layer after a long-term operation (5000 h). A protective oxide layer is of great importance for the long-term high-temperature operation of structural materials. The high-temperature oxidation behavior of AFAs and commercial 310S and 625 alloys in Air + 10% H 2 O at 800 °C and 900 °C is systematically investigated. Severe breakaway oxidation and minor spallation are observed for the 310S and 625 after the long-term operation, while the AFAs show high oxidation resistance. It is found that the formation of a continuous alumina layer could greatly prevent the volatilization of chromium vapors. In addition, the corresponding evolving models are discussed. Chromium evaporation from BoP components in high-temperature environment could severely deteriorate the electrochemical performance of SOFC. Several methods were applied to evaluate the Cr evaporation rates of BoP after 500 h exposure at 800 °C to 900 °C in air with 10% H 2 O. An optimal method was designed to exclude the effect of silicon (Si) deposits from quartz tube and sodium (Na) deposits from the sodium carbonate on the oxidation process and the chemical interaction between Cr gaseous species and alumina tube which could provide further quantitative correlation of the evaporated Cr species quantities and degradation rates of SOFC. Based on the great performance of AFAs after long-term operation, AFAs are assembled with Anode-supported cells (ASC) to investigate the the Cr deposition of anode-supported cell under a constant current density of 0.5 A cm -2 at 800 °C with AFA alloys compared with commercial alloys. In addition, the anodic and cathodic processes are deconvoluted by distribution of relaxation times (DRT) method which are comprehensively discussed. It is found out that the voltage exhibited a slight decrease of 5.09 % and 1.54 % in the presence of OC11 and OC11LZA alloy, respectively. However, a considerable decrease of 22.14 % and 12.06 % was determined in the presence of 310S and 625 alloy, respectively. AFAs possessing the low-cost, low Cr evaporation rates and the high oxidation resistance will make it of great potential to replace the existing BoP components.

01 COAL, LIGNITE, AND PEAT↗