Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

The physical chemistry and materials science behind sinter-resistant catalysts

Catalyst sintering, a main cause of the loss of catalytic activity and/or selectivity at high reaction temperatures, is a major concern and grand challenge in the general area of heterogeneous catalysis. Although all heterogeneous catalysts are inevitably subjected to sintering during their operation, the immediate and drastic consequences can be mitigated by carefully engineering the catalytic particles and their interactions with the supports. In this tutorial review, we highlight recent progress in understanding the physical chemistry and materials science involved in sintering, including the discussion of advanced techniques, such as in situ microscopy and spectroscopy, for investigating the sintering process and its rate. We also discuss strategies for the design and rational fabrication of sinter-resistant catalysts. To conclude, we showcase recent success in improving the thermal stability and thus sinter resistance of supported catalytic systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of Sintering Temperature on Microstructure and Electrical Properties of La{sub 0.67}Ba{sub 0.33}MnO{sub 3} Ceramic

In this study we report the effect of the sintering temperature of polycrystalline La{sub 0.67}Ba{sub 0.33}MnO{sub 3}(LBMO) manganites synthesized via solid state reaction method. LBMO have been sintered at 900 to 1200 deg. C in intervals of 100 deg. C. X-ray diffraction spectrum confirms that LBMO phase formation starts at 900 deg. C accompany by a minor second phase of BaMnO{sub 3} and fully forms into single phase of LBMO at 1200 degree sign C. SEM images showed that, the grain size increased with sintering temperature and leading to densifications or lower porosity. The T{sub p} was not affected by the sintering temperature. However, the electrical resistances of samples were decreased with the sintering temperature. At higher sintering temperature, due to grain growth and reduction of insulating BaMnO{sub 3} phase, the intergrain connectivity has been improved and the resistance drops.

36 MATERIALS SCIENCE↗

The Influence of Manganese Oxide on the Sintering Behavior of Yttria Tetragonal Zirconia

The sintering behavior of yttria-stabilized zirconia, with the influence of small additions of MnO{sub 2}(up to 1 wt %) sintered over the temperature range from 1250 deg. C to 1500 deg. C was investigated. It was found that the mechanical properties of Y-TZP were dependent on the dopant amount and sintering temperature. The results revealed that relative densities above 97.5% of theoretical (i.e. >5.95 Mgm{sup -3}) could be obtained in Y-TZPs sintered at low temperatures, 1250 deg. C and 1300 deg. C, with the additions of {<=}0.3 wt% MnO{sub 2}. In comparison to the undoped samples, the additions of up to 1 wt%MnO{sub 2} and for sintering up to 1350 deg. C was found to be beneficial in enhancing the Vickers hardness of the ceramic. The fracture toughness of Y-TZP however, was found to increase only in the 1 wt% MnO{sub 2}-doped samples when sintered above 1400 deg. C. The relation between the measured mechanical properties is discussed with the emphasis on the role of the manganese oxide.

36 MATERIALS SCIENCE↗

Sintering Effects on Morphology, Thermal Stability and Surface Area of Sol-Gel Derived Nano-Hydroxyapatite Powder

Hydroxyapatite (HAP) ceramics have been recognized as substitute materials for bone and teeth in orthopedic and dentistry field due to their chemical and biological similarity to human hard tissue. The nanosized and nanocrystalline forms of HAP have great potential to revolutionize the hard tissue-engineering field, starting from bone repair and augmentation to controlled drug delivery systems. This paper reports the synthesis of biomimetic nano-hydroxyapatite (HAP) by sol-gel method using calcium nitrate tetrahydrate (CNT) and potassium dihydrogen phosphate (KDP) as calcium and phosphorus precursors, respectively to obtain a desired Ca/P ratio of 1.67. Deionized water was used as a diluting media for HAP sol preparation and ammonia was used to adjust the pH to 11. After aging, the HAP gel was dried at 55 deg. C and sintered to different temperatures (200 deg. C, 400 deg. C, 600 deg. C, 800 deg. C, 1000 deg. C and 1200 deg. C). The dried and sintered powders were characterized for phase composition using Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD). The particle size and morphology was studied using transmission electron microscopy (TEM). The thermal behavior of the dried HAP nanopowder was studied in the temperature range of 55 deg. C to 1000 deg. C using thermal gravimetric analyser (TGA). The BET surface area of absorbance was determined by Nitrogen adsorption using Brunauer-Emmett-Teller (BET) method. The presence of characteristic peaks of the phosphate and OH groups in FTIR spectrums confirmed the formation of pure HAP in dried as well as sintered powders. XRD results also confirmed the formation of stoichiometric nano-HAP. Sintering revealed that with increase in temperature, both the crystallinity and crystallite size of nano-HAP particles increased. The synthesized nano-HAP powder was found to be stable upto 1000 deg. C without any additional phase other than HAP, whereas peak of {beta}-TCP (tricalcium phosphate) was observed at 1200 deg. C. Photomicrograph of TEM showed that the nanopowder sintered at 600 deg. C is composed of hydroxyapatite nanoparticles (26.0-45.6 nm), which is well in agreement with the crystallite size calculated using XRD data. TGA study showed the thermal stability of the synthesized nano-HAP powder. The BET surface area decreased with increase in sintering temperature.

36 MATERIALS SCIENCE↗

Microwave sintering of Ag-nanoparticle thin films on a polyimide substrate

Ag-nanoparticle thin films on a polyimide substrate were subjected to microwave sintering by use of a single-mode waveguide applicator. A two-step sintering process was employed. First, at low conductivities of the film, the film sample was placed at the site of the maximum electric field and subjected to microwave irradiation. Second, when the conductivity of the film increased, the film sample was placed at the site of the maximum magnetic field and again subjected to microwave irradiation. The microwave sintering process was completed within 1.5 min, which is significantly lower than the time required for the oven heating process. The resulting conductivity of the film, albeit only 30% of that of the bulk material, was seven times that of a film annealed at the same temperature in a furnace. Scanning electron microscopy images revealed that the nanoparticles underwent both grain necking and grain growth during microwave sintering. In addition, this sintering process was equivalent to the oven heating process performed at a 50 °C higher annealing temperature. An electromagnetic wave simulation and a heat transfer simulation of the microwave sintering process were performed to gain a thorough understanding of the process.

36 MATERIALS SCIENCE↗

Effect of sintering temperature on structural and dielectric properties of Bi and Li co-substituted SrTiO{sub 3}

Sintering is an important factor that affects the microstructure development in ceramics. In this work, Bi and Li co-substituted Strontium Titanate (ST) ceramics samples sintered at different temperatures are prepared and analyzed by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). XRD was used to detect phase structure of the sintered samples and SEM was used for microstructure analysis. Dielectric properties of Bi and Li co-substituted SrTiO{sub 3} samples were measured using Agilent 4294A Impedance analyzer in the frequency range 40 Hz to 5 MHz at room temperature. The result reveals that the dielectric constant of Bi and Li co-substituted SrTiO{sub 3} ceramics increases with increasing sintering temperature up to 1250°C and then decreases beyond that. The highest value of dielectric constant obtained is 860 at 1KHz frequency and lowest dielectric loss observed is 0.04 at the same frequency for samples sintered at 1250°C. Also the grain size increases with increase of sintering temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Improvement of the electrochromic response of a low-temperature sintered dye-modified porous electrode using low-resistivity indium tin oxide nanoparticles

An indium tin oxide (ITO) nanoparticle-based porous electrode sintered at low temperatures was investigated as a transparent electrode for electrochromic displays (ECDs). The electrochromic (EC) response of the dye-modified ITO porous electrode sintered at 150 °C, which exhibited a generally low resistivity, was markedly superior to that of a conventional dye-modified TiO{sub 2} porous electrode sintered at the same temperature. Moreover, the EC characteristics of the dye-modified ITO porous electrode sintered at 150 °C were better than those of the high-temperature (450 °C) sintered conventional dye-modified TiO{sub 2} porous electrode. These improvements in the EC characteristics of the dye-modified ITO porous electrode are attributed to its lower resistivity than that of the TiO{sub 2} porous electrodes. In addition to its sufficiently low resistivity attained under the sintering conditions required for flexible ECD applications, the ITO porous film had superior visible-light transparency and dye adsorption capabilities. We conclude that the process temperature, resistivity, optical transmittance, and dye adsorption capability of the ITO porous electrode make it a promising transparent porous electrode for flexible ECD applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Reliability and Lifetime Prediction Model of Sintered Silver Under High-Temperature Cycling

Although excellent reliability has been reported for sintered silver as a die-attach material under both thermal and power cycling loads in power electronics applications, the promise of this material as a large-area attachment at temperatures beyond 200 degrees C needs to be investigated. This paper presents insights into the thermomechanical behavior and reliability of sintered silver under extreme thermal cycling conditions. In this study, we bonded sintered silver samples and subjected it to a thermal cycling profile of -40 °C to 200 °C with high ramp rates. We periodically monitored samples under thermal cycling to detect the presence of any failure mechanisms using a scanning acoustic microscope. We also included 95Pb5Sn solder in the study to obtain reference data. Results show the occurrence of cracks in sintered silver followed by a rapid rate of crack growth that exceeded the failure criterion in just 50 cycles. The predominant failure mechanism we observed was adhesive failure. As a large-area attachment, solder exhibited a higher reliability than sintered silver but failed within 100 cycles. Finally, we performed thermomechanical modeling to compute strain energy density values and correlated these with the experimentally observed crack growth rates to formulate a lifetime prediction model for sintered silver.

30 DIRECT ENERGY CONVERSION↗

Shrinkage, microstructure, and mechanical properties of sintered 3D-printed silica via stereolithography

Stereolithography has been used to create ceramic parts with complex geometry that is difficult to achieve with conventional fabrication techniques. Here this study used stereolithography to print silica honeycomb structures with a commercial Formlabs Form2 printer. The printed samples were sintered at different temperatures, and the print shape was retained up to 1300°C, but significant distortion from partial melting occurred at 1400°C. Higher sintering temperatures lead to more shrinkage, but it is non-uniform among directions, with the open cell plane shrinking more than the dense plane of the sample. As expected, the density of samples also increases with the sintering temperature. At higher sintering temperatures, there is an increase in cristobalite and a decrease in quartz, tridymite, and amorphous silica. Regarding mechanical properties, the out-of-plane compressive strength is approximately one order of magnitude higher than the in-plane compressive strength. When compressed along the out-of-plane direction, the samples sintered at lower temperatures surprisingly exhibit higher strength, which is explained by the micro-cracking mechanism. As expected, the samples sintered at higher temperatures display higher strength when compressed along the in-plane direction.

36 MATERIALS SCIENCE↗

Particle atomic layer deposition of alumina for sintering yttria-stabilized cubic zirconia

The addition of aluminum oxide (Al 2 O 3 ) as a sintering aid to yttria-stabilized zirconia (YSZ) reduces the required densification temperature. Sintering aids are incorporated using a number of processes which can lead to ambiguity when determining the effect of the sintering aid on the densification mechanism. In this study, a novel method for sintering aid addition, Particle Atomic Layer Deposition (ALD), was used to deposit an amorphous Al 2 O 3 thin film on YSZ particles. Transmission electron microscopy confirmed the deposition of conformal Al 2 O 3 thin films on the surface of the YSZ particles. The addition of Al 2 O 3 to YSZ reduced the temperature at which densification began by ~75 degrees C, and 2.2 wt% Al 2 O 3 addition resulted in a minimum activation energy for the intermediate stage of densification. This concentration is well in excess of the solubility limit of Al 2 O 3 in YSZ, showing that Al 2 O 3 does not enhance the densification of YSZ solely by dissolving into the YSZ lattice and activating volume diffusion. The addition of 0.7 wt% Al 2 O 3 with one Particle ALD cycle enhanced the ionic conductivity of YSZ by 23% after sintering at 1350 degrees C for 2 hours, demonstrating that dense parts with high oxygen ion conductivities can be produced after sintering at reduced temperatures. One Particle ALD cycle is a fast, easily scaled-up process that eliminates the use of solvents and has substantial cost/performance advantages over conventional processing.

36 MATERIALS SCIENCE↗

Flash Sintering of Oxide Ceramics under Microwave Heating

We report on the results of the analysis of the effect of flash sintering, which is observed upon heating compacted powder materials by high-intensity microwave radiation. Ceramic samples of Y{sub 2}O{sub 3}, MgAl{sub 2}O{sub 4}, and Yb: (LaO){sub 2}O{sub 3} were sintered to a density exceeding 98–99% of the theoretical value during 0.5–5 min without isothermal hold. The specific microwave power absorbed volumetrically in the samples was 20–400 W/cm{sup 3}. Based on the analysis of the experimental data (microwave radiation power and heating and cooling rates) and of the microstructure of the obtained materials, we propose a mechanism of flash sintering based on the evolution of the thermal instability and softening (melting) of the grain boundaries. The proposed mechanism also explains the flash sintering effect observed when a dc or a low-frequency ac voltage is applied to the samples. The microwave heating makes it possible to implement flash sintering without using electrodes for supplying energy to the articles being sintered.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Development of Macroscale Models of UO 2 Fuel Sintering and Densification using Multiscale Modeling and Simulation

Light water reactor fuel pellets are fabricated using sintering to final densities of 95% or greater. During reactor operation, the porosity remaining in the fuel after fabrication decreases further due to irradiation-assisted densification. While empirical models have been developed to describe this densification process, a mechanistic model is needed as part of the ongoing work by the NEAMS program to develop a more predictive fuel performance code. In this work we will develop a phase field model of sintering of UO 2 in the MARMOT code, and validate it by comparing to published sintering data. We will then add the capability to capture irradiation effects into the model, and use it to develop a mechanistic model of densification that will go into the BISON code and add another essential piece to the microstructure-based materials models. The final step will be to add the effects of applied fields, to model field-assisted sintering of UO 2 . The results of the phase field model will be validated by comparing to data from field-assisted sintering. Tasks over three years: 1. Develop a sintering model for UO 2 in MARMOT 2. Expand model to account for irradiation effects 3. Develop a mechanistic macroscale model of densification for BISON

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Electric-Loading Enhanced Kinetics in Oxide Ceramics: Pore Migration, Sintering and Grain Growth: Final Report

Solid oxide fuel cells and solid oxide electrolysis cells rely on solid electrolytes in which a large ionic current dominates. This project was initiated to investigate microstructural changes in such devices under electrochemical forces, because nominally insignificant processes may couple to the large ionic current to yield non-equilibrium phenomena that alter the microstructure. Our studies had focused on yttria-stabilized cubic zirconia (YSZ) widely used in these devices. The experiments have revealed enhanced grain growth at higher temperatures, pore and gas bubble migration at all temperatures, and the latter also lead to enhanced sintering of highly porous ceramics into fully dense ceramics at unprecedentedly low temperatures. These results have shed light on kinetic processes that fall completely outside the realm of classical ceramic processing. Other fast-oxygen oxide ceramics closely related to, and often used in conjunction with zirconia ceramics, have also be investigated, as are closely related scientific problems in zirconia ceramics. These include crystal structures, defects, diffusion kinetics, oxygen potentials, low temperature sintering, flash sintering, and coarsening theory, and all have resulted in greater clarity in scientific understanding. The knowledge is leveraged to provide new insight to electrode kinetics and near-electrode mixed conductivity and to new materials. In the following areas, our research has resulted in completely new knowledge that defines the state-of-the-art of the field. (a) Electrical current driven non-equilibrium phenomena, (b) Enhanced grain growth under electrochemically reducing conditions, (c) Development of oxygen potential polarization in electrically loaded electrolyte, (d) Low temperature sintering and grain growth, and (e) Structure, defects and cation kinetics of fluorite-structured oxides. Our research has also contributed to synthesis of new energy-relevant electrochemical materials and new understanding of flash sintering, which is a rapid sintering process initiated by a large electrical loading.

36 MATERIALS SCIENCE↗

On the Sintering Behavior of Nb2O5 and Ta2O5 Mixed Oxide Powders

A mixed oxide system consisting of Nb2O5 and Ta2O5, was subjected to annealing in air/hydrogen up to 950 °C for 1–4 h to study its sintering behavior. The thermogravimetric–differential scanning calorimetry (TGA–DSC) thermograms indicated the formation of multiple endothermic peaks at temperatures higher than 925 °C. Subsequently, a 30% Ta2O5 and 70% Nb2O5 (mol%) pellet resulted in good sintering behavior at both 900 and 950 °C. The scanning electron microscope (SEM) images corroborated these observations with necking and particle coarsening. The sintered pellets contained a 20.4 and 20.8% mixed oxide (Nb4Ta2O15) phase, along with Ta2O5 and Nb2O5, at both 900 and 950 °C, indicating the possibility of the formation of a solid solution phase. In situ high-temperature X-ray diffraction (XRD) scans also confirmed the formation of the ternary oxide phase at 6 and 19.8% at 890 and 950 °C, respectively. The Hume–Rothery rules could explain the good sintering behavior of the Ta2O5 and Nb2O5 mixed oxides. An oxide composition of 30% Ta2O5 and 70% Nb2O5 (mol%) and a sintering temperature of 950 °C appeared adequate for fabricating well-sintered oxide precursors for subsequent electrochemical polarization studies in fused salts.

36 MATERIALS SCIENCE↗

Method to Determine Maximum Allowable Sinterable Silver Interconnect Size

The use of sintered-silver for large-area interconnection is attractive for some large-area bonding applications in power electronics such as the bonding of metal-clad, electrically-insulating substrates to heat sinks. Arrays of different pad sizes and pad shapes have been considered for such large area bonding; however, rather than arbitrarily choosing their size, it is desirable to use the largest size possible where the onset of interconnect delamination does not occur. If that is achieved, then sintered-silver's high thermal and electrical conductivities can be fully taken advantage of. Toward achieving this, a simple and inexpensive proof test is described to identify the largest achievable interconnect size with sinterable silver. The method's objective is to purposely initiate failure or delamination. Copper and invar (a ferrous-nickel alloy whose coefficient of thermal expansion (CTE) is similar to that of silicon or silicon carbide) disks were used in this study and sinterable silver was used to bond them. As a consequence of the method's execution, delamination occurred in some samples during cooling from the 250 degrees C sintering temperature to room temperature and bonding temperature and from thermal cycling in others. These occurrences and their interpretations highlight the method's utility, and the herein described results are used to speculate how sintered-silver bonding will work with other material combinations.

30 DIRECT ENERGY CONVERSION↗

Process Simulation of Cold Pressing and Sintering of Armstrong CP-Ti Powders

A computational methodology is presented for the process simulation of cold pressing and sintering of Armstrong CP-Ti powders. Since the powder consolidation is governed by specific pressure-dependent constitutive equations, solution algorithms were developed for the ABAQUS user material subroutine, UMAT, for computing the plastic strain increments based on an implicit integration of the nonlinear yield function, flow rule, and hardening equations. Sintering was simulated using a model based on diffusional creep using the user subroutine CREEP. The initial mesh, stress, and density for the simulation of sintering were obtained from the results of the cold pressing simulation, minimizing the errors from decoupling the cold pressing and sintering simulations. Numerical simulation results are presented for the cold compaction followed by a sintering step of the Ti powders. The numerical simulation results for the relative density were compared to those measured from experiments before and after sintering, showing that the relative density can be accurately predicted. Notice: This manuscript has been authored by UT-Battelle, LLC, under Contract No. DE-AC05-00OR22725 with the U.S. Department of Energy. The United States Government retains and the publisher, by accepting the article for publication, acknowledges that the United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes. ACKNOWLEDGEMENTS This research was sponsored by the U.S. DOE, and carried out at ORNL, under Contract DE-AC05-00OR22725 with UT-Battelle, LLC. This research was sponsored by the U.S. DOE, EERE Industrial Technology Program Office under CPS Agreement # 17881.

36 MATERIALS SCIENCE↗

Effect of carbon impurity during the sintering of MOX fuels

UO{sub 2} and PuO{sub 2} powders are currently used as raw materials for the industrial fabrication of mixed uranium plutonium oxide (MOX) for light-water reactors. The mixture is pelletized before being sintered at 1700 Celsius degrees under a reducing atmosphere of Ar/4%H{sub 2} with 1200 vpm H{sub 2}O. At the end of the oxide ceramic sintering process, a swelling phenomenon sometimes occurs and could be responsible for the fuel non-compliance with safety specifications. This phenomenon is often caused by the presence of carbon impurities in the raw materials. In this paper, it will be shown how carbon impurities (naturally present or deliberately introduced) in the raw materials affect MOX fuel densification by sintering. For that purpose, MOX densification has been monitored by dilatometric measurements and the gases released during sintering have been continuously qualitatively and quantitatively analyzed. Gases released or trapped in the fuel during densification have been studied, as well as the sintered fuel characteristics (density, microstructure, U/Pu distribution). Results confirm that carbon impurities can play a major role in the fuel swelling: the oxides react with carbon and form gaseous CO molecules that could be trapped in the closed pores during sintering. This leads to a pressure increase within pores responsible for an irreversible swelling by creep deformation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Two-Step Reactive Aid Sintering of BaZr 0.8 Y 0.2 O 3-δ Proton-Conducting Ceramics

Ceramic-based proton conductors enable high-temperature hydrogen economy applications such as hydrogen separation membranes, fuel cells, and steam electrolyzers. BaZr 0.8 Y 0.2 O 3-δ (BZY) proton-conducting oxide possesses the highest level of proton conductivity reported to date, but poor sinterability hinders its widespread utilization. Here, we report a two-step reactive aid sintering (TRAS) method involving the introduction of BaCO 3 and B 2 O 3 -Li 2 O for the preparation of dense BZY ceramics sintered at 1500°C. The resulting BZY samples showed a pure perovskite structure with a dramatic increase in the relative density to 91.5%. In addition, the shrinkage during sintering was improved to 19.3% by a TRAS method as compared to 2.6% by the conventional solid date reaction method. Moreover, the bulk conductivity was improved due to enhanced densification, while the grain boundary conductivity decreased due to the blocking behavior of the sintering aid resulting in a decrease in the total conductivity of the samples.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗