The effect of surface contamination on contact angles and surface potentials Summary report
Surface contamination effects on behavior of liquids in space vehicle tanks at zero gravity
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Surface contamination effects on behavior of liquids in space vehicle tanks at zero gravity
Not Available
Defects and roughness at a material’s surface can allow for the formation of a material jet when a shockwave reaches a surface. The formation of a jet can lead to significant material damage of the shocked material, as well as the downstream material that the jet impacts. Here, we utilize planar shocks in single crystal aluminum to assess initial jetting formation for surface notches and sub-surface porosity. In the case of surface notches, we find that changing the width of the notch can cause the shock breakout response to transition from a standard jetting mechanism to an atomic atomization at high velocities. This transition occurs due to the mechanisms associated with lateral relaxations within the notch and how this interacts with the shock focusing event that induces jetting. For sub-surface pores, the pore collapse induces a re-shock, localized near the pore, that is stronger than the initial shock, but unsupported. Changing the pore dimensions and location relative to the surface influences the strength of the shock that emanates from its collapse when it reaches the surface, leading to a variety of different breakout conditions including jetting and localized material failure.
Surface shear effect on buckling of cylindrical shells, noting similarity of equations derived from thermoelastic problems of thin cylindrical shells
Surface emittance effect on turbulent skin friction at supersonic and low hypersonic speeds
Surface roughness effects on normal spectral emittance of vapor deposited rhenium
Radiative heat transfer between opaque interacting surfaces for equal temperature adjoint plates with one dimensional surface roughness profile
The effect of surface finish on the strength-grain size relation was investigated for dense hot-pressed SiC. Failure initiated predominantly via the propagation of extrinsic machining-induced flaws for the range of grain sizes and machining grit sizes studied. These results are consistent with the region of large-grain-size flaw control as delineated by Prochazka and Charles. The severity of machining-induced flaws, relative to the machining grit size, decreased with increasing machining grit size and decreasing SiC grain size.
Explore the source record for details and available documents.
Not Available
The silica support of a Co-based catalyst for Fischer–Tropsch (FT) synthesis was modified by the chelating agents (CAs) nitrilotriacetic acid (NTA) and ethylenediaminetetraacetic acid (EDTA). After the modification, characterization of the fresh and spent catalysts shows reduced crystallite sizes, a better-dispersed Co 3 O 4 phase on the calcined samples, and increased metal dispersions for the reduced samples. The CA-modified catalysts display higher CO conversions, product yields, reaction rates, and rate constants. The improved FT performance of CA-modified catalysts is attributed to the formation of stable complexes with Co. Finally, the superior performance of the EDTA-modified catalyst in comparison to the NTA-modified catalyst is due to the higher affinity of the former for complex formation with Co ions.
Surface roughness effects in full-film EHL contacts were studied. A flow factor modification to the Reynolds equation was applied to piezoviscous-elastic line contacts. Results for ensemble-averaged film shape, pressure distribution, and other mechanical quantities were obtained. Asperities elongated in the flow direction by a factor exceeding two decreased both film shape and pressure extrema at constant load; isotropic or transverse asperities increased these extrema. The largest effects are displayed by traction, which increased by over 5% for isotropic or transverse asperities and by slightly less for longitudinal roughness.
In this paper, an experimental and numerical investigation of internal cooling channels with rib turbulators is presented with sCO 2 as the working fluid at process conditions (pressure-20.7 MPa and temperature up to 150 °C). The effect of channel aspect ratio up to 2:1 on thermal-hydraulic performance is explored in additively manufactured rectangular channels and square channels, both with and without 60 deg ribs on the top and bottom sides. The Wilson-plot method is employed to experimentally measure channel-averaged Nusselt number over a Reynolds number range up to 370,000. The friction factor is calculated from pressure drop and mass flow rate and additionally, the overall thermal performance factor (TPF) is reported. A companion computational fluid dynamics (CFD) simulation is performed for the rib turbulated cooling configurations reported in the experiments using the Reynolds average Navier–Stokes-based turbulence model. The objective of the numerical study is to gain insight into the local heat transfer augmentation in the ribbed channels as a result of varying the aspect ratio, channel configuration (square versus rectangular), operating conditions (Reynolds number) and the surface roughness, an inherent outcome of the additive manufacturing process. Surface roughness is simulated using sand grain roughness height (K S ) calculated from the experimental data, and a comparison is presented with the corresponding channel configuration with varying surface roughness heights starting from smooth surfaces (K S = 0). Experimental results indicate that the heat transfer augmentation is negligible in the rectangular channels with ribs on the long side compared to the square channel. However, it is enhanced by 60% in comparison to placing ribs on the shorter side. The TPF remains constant at around 1 for the entire range of Reynolds numbers consistent with prior work at the National Energy Technology Laboratory (NETL). Here, the simulation results highlight that increased surface roughness can have a favorable considerable influence on Nusselt number and overall thermal performance enhancement.
The effects of an isolated, two-dimensional roughness element on the spatial development of instability waves in boundary layers are investigated by numerically integrating the two-dimensional, time-dependent, incompressible Navier-Stokes equations, using a finite difference/Chebyshev discretization. It is shown that (high) inviscid frequencies have higher growth rates than Tollmien-Schlichting frequencies, indicating that disturbances growing in the separation zone are controlled by the inviscid instability of the shear layer at the edge of the separation zone.
In this study, the results of NREL's continued work on experimental characterization of the thermal performance of free-surface jets of automatic transmission fluid impinged on a heated target surface are presented. The measured heat transfer coefficients are useful for understanding factors influencing performance of driveline fluid-based cooling systems for electric machines and help designers in developing high-performance, power-dense and reliable machines. Experiments were carried out for different fluid and target surface temperatures (50 degrees C, 70 degrees C, and 90 degrees C for the fluid and 90 degrees C, 100 degrees C, 110 degrees C, and 120 degrees C for the target surface). Impinging jet velocities (0.5 m/s to 7.5 m/s) and the jet position on the target surface (center versus edge) were also varied. The impinging angle was kept at 90 degrees relative to the target surface. It was found that higher target surface temperature increased heat transfer coefficients, namely, increasing surface temperature from 90 degrees C to 120 degrees C enhanced heat transfer coefficient values at higher impinged jet velocities (7.5 m/s) by up to 15%.
Being a nonequilibrium material, the structure of glass varies with the sample history. Thus, the initial surface condition of a glass can vary with the preparation condition and have a large impact on its reactivity. This paper shows that the aqueous corrosion behavior of international simple glass (ISG) varies depending on the initial surface state. The ISG glass samples were prepared as-polished-only and polished-then-annealed and they were immersed in aqueous solution saturated with soluble SiO 2 at 30°C (modeling a mild condition) and at 90°C (modeling a severe condition). Molecular dynamics simulations were performed to obtain coordination numbers of network formers of ISG to assist oxygen speciation calculations. The surface structures of as-prepared and corroded ISG samples were analyzed using various imaging and spectroscopic techniques. Among these analyses, only the oxygen speciation with x-ray photoelectron spectroscopy showed discernable differences between two uncorroded surfaces with different preparation histories; all other methods could not differentiate the surface preparation history before aqueous corrosion. Such minor difference in chemical structures was found to have a profound impact on corrosion behaviors in the mild condition. In the harsh condition, the surface history dependence was not as drastic as the corrosion in the mild condition. The analysis results of the corroded surfaces suggested that the thickness and structure of the alteration layer formed on ISG in aqueous corrosion can vary with the initial surface state.
Effect of surface states and photovoltaic effect on oxide-semiconductor interface