SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Temperature at which predecomposition or decomposition of ammonium perchlorate occurs, changed by perchlorate surface treatment and reflected in burning rate of propellant containing perchlorate
Surface oxide, organic and lead film effects on friction and plastic deformation of Zn single crystal during sliding
A flight test program was conducted in which the effects of various surface coatings on aerodynamic drag were investigated; results of this program are described in this report. The tests were conducted at NASA-Langley Research Center on the terminal configured vehicle (TCV) Boeing 737 research airplane. The Boeing Company, as contractor with NASA under the Energy Efficient Transport (EET) program, planned and evaluated the experiment. The NASA-TCV Program Office coordinated the experiment and performed the flight tests. The principal objective of the test was to evaluate the drag reduction potential of an elastomeric polyurethane surface coating, CAAPCO B-274, which also has been considered for application on transport airplanes to protect leading edges from erosion. The smooth surface achievable with this type of coating held some promise of reducing the skin friction drag as compared to conventional production type aircraft surfaces, which are usually anodized bare metal or coated with corrosion protective paint. Requirements for high precision measurements were the principal considerations in the experiment.
The effect of streamline geometry and pressure distributions on surface heating rates is examined for slender, spherically blunted cones. The modifications to the approximate aeroheating code include a curve fit of pressures computed by an Euler solution over a range of Mach numbers and cone angles. The streamline geometry is then found using the surface pressures and inviscid surface properties. Previously, streamlines were determined using the inviscid properties at the edge of the boundary layer when accounting for the effects of entropy-layer swallowing. Streamline calculations are now based on inviscid surface conditions rather than boundary-layer edge properties. However, the heating rates are calculated using inviscid properties at the edge of the boundary layer. Resulting heating rates compare favorably with solutions from the viscous-shock-layer equations.
The influence of surface cooling on compressible boundary layer instability is discussed theoretically for both viscous and inviscid modes, at high Reynolds numbers. The cooling enhances the surface heat transfer and shear stress, creating a high heat transfer sublayer. This has the effect of distorting and accentuating the viscous Tollmien-Schlichting modes to such an extent that their spatial growth rates become comparable with, and can even exceed, the growth rates of inviscid modes, including those found previously. This is for moderate cooling, and it applies at any Mach number. In addition, the moderate cooling destabilizes otherwise stable viscous or inviscid modes, in particular triggering outward-traveling waves at the edge of the boundary layer in the supersonic regime. Severe cooling is also discussed as it brings compressible dynamics directly into play within the viscous sublayer. All the new cooled modes found involve the heat transfer sublayer quite actively, and they are often multi-structured in form and may be distinct from those observed in previous computational and experimental investigations. The corresponding nonlinear processes are also pointed out with regard to transition in the cooled compressible boundary layer. Finally, comparisons with Lysenko and Maslov's (1984) experiments on surface cooling are presented.
The total amount of ozone in a vertical column is being measured by Nimbus 4 and 7 observations of the intensity of ultraviolet sunlight scattered from the earth. The algorithm for deriving the amount of ozone from the observations uses the assumption that the surface reflects the light isotropically and the albedo is independent of wavelength. The effects of anisotropic surfaces and clouds on the estimate of total ozone are computed for models of the earth-atmosphere system.
Catalytic effects of materials surfaces on oxygen atom recombination at low pressures
Unsteady flows are becoming a more characterized field of study as advancements in technology is allowing for more high-speed, time-resolved data acquisition. It is important to understand these flows as the shock-wave boundary-layer interactions and separation they are involved with can generate extreme loads caused by high pressure and temperature on the body of a flight vehicle. It is vital to characterize these loads, as they can impede upon the structural integrity of a high-speed system. A common instrument utilized today to characterize pressure distributions caused by unsteady flows are unsteady pressure transducers. Set flush with the surface of a flight vehicle or wind tunnel model, these transducers can provide a pressure distribution, capturing the frequency of unsteady loads that could impinge upon the test article. A couple negative aspects of this instrumentation is that they are expensive, have long lead times, and a pressure distribution can only be determined in one discrete location where the transducer is installed. An optical diagnostic known as unsteady pressure-sensitive paint (uPSP) can help to satisfy these deficiencies. This is a spray paint that can be applied to a surface of a model to provide a global pressure distribution across the whole painted region.2 A complete picture of the fluid dynamic pressures occurring on the surface of a test article can be analyzed, especially in locations where it may have been impossible to install a transducer. Pressure-sensitive paint is also less expensive than traditional pressure transducers, which are, on average, about $2,000 each including the cost of installation.3 Unsteady PSP will not replace unsteady pressure transducers, but the transducers can be used to validate the PSP response to the flow and measure frequencies higher than the frequency response of the paint. One issue that can arise using these tools simultaneously, is that the surface roughness of the uPSP can affect the pressure readings of the transducers. Applying the uPSP to the surface of the model is going to affect the flow in some way as the topography of the model is now different than if it was not painted. One study with steady PSP conducted by Amer, Obara, and Liu at NASA Langley concluded that the PSP surface roughness was minimally intrusive at different test conditions with various lift, drag, etc., however, it was noted that data from some pressure transducers had decreased, likely due to the uneven application of the PSP in the localized region of the transducers.9 Sugioka et. al. tested various formulations of uPSP to study surface roughness effects on a Common Research Model (CRM) in transonic flow. The influence of uPSP on the surface of the model, depending on how it was formulated, was noted to have the possibility of relocating the shock wave present in the flow. This study was conducted to examine and compare transducer data acquired in December 2017 of a 4% scale model of the Space Launch System (SLS) performed at NASA Ames Research Center (ARC) Unitary Plan Wind Tunnel (UPWT). One goal of the test was to demonstrate to the customer the potential of the uPSP system developed at NASA ARC. The effect of uPSP on transducer signals also became an interest in this experiment and is the reason for this data analysis. The results of this study were discussed with the SLS team to help them make decisions regarding the next test on an SLS model with the PSP and Unitary Plan Wind Tunnel teams.
Effect of three surface finishes of roughness 4 to 5, 20 to 25, and 70 to 80 micro inches rms on fatigue properties were determined for low-carbon N-155 alloy of grain size A.S.T.M. 1 at temperatures of 80 , 1000, 1350, and 1500 F. The fatigue properties for the various finishes differed appreciably at room temperature; however, after short periods at 1000 F and for all periods investigated at temperatures above 1000 F, the specimen finishes had the same fatigue strength. It was concluded that the primary cause of the difference in room-temperature strength was due to compressive stresses set up in the surface and that at elevated temperatures these compressive stresses were relieved by annealing. Apparently, roughness alone did not significantly affect fatigue strength.
The important aspects of elastohydrodynamic lubrication, with a single, one-dimensional asperity, have been found by solving numerically the coupled transient Reynolds equation and the elasticity equation. Even though the assumption of a single asperity is highly ideal, this study sheds some light on the effect of surface roughness on elastohydrodynamic lubrication. The results show that the film pressure tends to increase more than the steady state pressure, and in particular, the increase in pressure reaches a maximum as the asperity approaches the inlet of the contact region. The asperity height and the pressure increase above the steady state pressure are closely related to each other; the higher the asperity height, the larger the pressure increase. In the pure rolling case, it has been found that a local pressure peak is not developed. However, in the cases of sliding and rolling, a small, local pressure peak is developed on the pressure profile when the asperity moves into the contact region. In general, the overall film thickness profile increases with increasing asperity height, but is not significantly affected by the asperity width. Moreover, the slope of the overall film thickness profile for the transient cases is much greater than the steady state profile, which is approximately constant across the contact width. The increase in the center film thickness also depends upon the width and height of the asperity.
Measurements of peak overpressure and Mach stem height were made at four burst heights. Data were obtained with instrumentation capable of directly observing the variation of shock wave movement with time. Good similarity of free air shock peak overpressure with larger scale data was found to exist. The net effect of surface roughness on shock peak overpressures slightly. Surface roughness delayed the Mach stem formation at the greatest charge height and lowered the growth at all burst heights. A similarity parameter was found which approximately correlates the triple point path at different burst heights.
The thermal film-cooling footprints observed by infrared imagery for three coolant-passage configurations embedded in adiabatic-test plates are discussed. The configurations included a standard round-hole cross section and two orientations of a vortex-generating flow passage. Both orientations showed up to factors of four increases in both film-cooling effectiveness and surface coverage over that obtained with the round coolant passage. The crossflow data covered a range of tunnel velocities from 15.5 to 45 m/sec with blowing rates from 0.20 to 2.05. A photographic streakline flow visualization technique supported the concept of the counterrotating apability of the flow passage design and gave visual credence to its role in inhibiting flow separation.
The adsorption of a water molecule on surfaces of beta-AgI, the hexagonal crystal believed to be primarily responsible for the ice-nucleating properties of AgI, is studied on the basis of an effective pair potential model. The water molecule is represented by a rigid point charge ST-2 model and the AgI substrate by an array of point atoms, and maximal binding energy surfaces and optimal H2O configurations are generated for the water molecule adsorbed on the rigid and unrelaxed basal and prism faces. Modeling of H2O adsorption above a two-layer ledge, an iodine vacancy and an H2O molecule trapped in the vacancy indicates that H2O adsorption is favored at interstitial sites where no substrate atoms lie directly below. The prism face is found to attract the water molecule more strongly and provide larger energy barriers to surface diffusion than basal face sites, with the ideal basal faces providing hexagonal patterns of adsorption sites for the H2O with preferred dipole moments aligned.
Dust devils have been proposed as effective mechanisms for lofting large quantities of dust into the martian atmosphere. Previous work showed that vortices lift dust more easily than simple boundary layer winds. The aim of this study is to determine experimentally the effects of non-erodable roughness elements on vortex particle threshold through laboratory simulations of natural surfaces. Additional information is included in the original extended abstract.
A form of sulfur that is white at room temperature and very fluffy in texture has been found in laboratory experiments on the effects of vacuum sublimation (evaporation) on solid sulfur. This work is an outgrowth of proton sputtering experiments on sulfur directed toward understanding Jovian magnetospheric effects on the surface of Io. Fluffy white sulfur is formed on the surface of solid yellow, tan, or brown sulfur melt freezes in vacuum by differential (fractional) evaporation of two or more sulfur molecular species present in the original sulfur; S(8) ring sulfur is thought to be the dominant sublimination phase lost to the vacuum sink, and polymeric chain sulfur S(u) the dominant residual phase that remains in place, forming the residual fluffy surface layer. The reflectance spectrum of the original sulfur surface is greaty modified by formation of the fluffy layer: the blue absorption band-edge and shoulder move 0.05 to 0.06 microns toward shorter wavelengths resulting in a permanent increase in reflectivity near 0.42 to 0.46 microns; the UV reflectivity below 0.40 microns is reduced. This form of sulfur should exist in large quantity on the surface of Io, especially in hotspot regions if there is solid free sulfur there that has solidified from a melt. Its color and spectra will indicate relative crystallization age on a scale of days to months and/or surface temperature distribution history.
The main objective of this research is to address two important but unresolved problems: (1) the measurement of vertical and transverse length scales via space correlations for all Reynolds stress components and velocity-temperature correlations, both in the free stream and within the boundary layer using the existing triple and quad-wire probes; and (2) to relate the character of the free stream turbulence to the character of the turbulence within the boundary layer in order to determine the effect on surface heat transfer.
The results of a Navier-Stokes analysis for predicting the change in turbine efficiency due to a change in either incidence or surface roughness is discussed. It was experimentally determined by Boynton, Tabibzadeh, and Hudson that polishing the SSME high pressure fuel turbine blades improved turbine efficiency by about 2 points over a wide range of operating conditions. These conditions encompassed the range of incidence seen by the turbine blading during flight. It is also necessary to be able to predict turbine performance at various operating points for future rocket turbopump applications. The code RVCQ3D, developed by Rod Chima, was used to determine the effects of changes in incidence angle on turbine blade row efficiency. The midspan Navier-Stokes results were used in conjunction with an inviscid flow analysis code to predict the efficiency of the two stage SSME over a wide range of operating conditions for smooth and rough turbine blades. The use of the Navier-Stokes analysis to predict changes in turbine efficiency due to variation in incidence angles was found to be superior to other incidence loss correlations available in the literature. The sensitivity of the Navier-Stokes results to grid parameters is discussed. The effects of the surface roughness were accounted for using the Cebeci-Chang rough wall turbulence model. This model was implemented in the code RVCQ3D. The implementation of this model for predicting the change in efficiency is also discussed.
The objective is to study quantitatively thermocapillary flows in two-dimensional and axisymmetric geometries in order to learn the impact of such flows on float-zone refining configurations. The work begins with the analytical study of steady flows in slots and zones to obtain predictions of surface curvature, flow and heat transport. It then examines the instability of such flows. Three new instability mechanisms have been identified and the results show that thermocapillary flows of high Prandtl number fluid become convectively unstable while those of low Prandtl number fluid become hydrodynamically unstable. The work includes numerical simulations of steady, high Marangoni number flows in unit aspect ratio boxes and asymptotic solutions in large boxes. Furthermore, the effect of surface contamination on the steady thermocapillary flows was examined. This fundamental study focused on fluid dynamical systems used to understand events in the flow of melts in float-zone geometries both on Earth and in microgravity environments.