Search NASA⌕ Search

SEARCH · Search NASA

Results for “TAIL SURFACES, VERTICAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Effect of simulated in-flight thrust reversing on vertical-tail loads of F-18 and F-15 airplane models

Investigations were conducted in the Langley 16-Foot Transonic Tunnel to provide data on a 0.10-scale model of the prototype F-18 airplane and a 0.047-scale model of the F-15 three-surface configuration (canard, wing, and horizontal tails). Test data were obtained at static conditions and at Mach numbers from 0.6 to 1.2 over an angle-of-attack range from 2 deg to 15 deg. Nozzle pressure ratio was varied from jet off to about 8.0.

Bare, E. A.↗
NASA NTRS1952

Investigation of the Influence of Fuselage and Tail Surfaces on Low-speed Static Stability and Rolling Characteristics of a Swept-wing Model

Results are presented of a wind-tunnel investigation to determine influence of the fuselage and tail on static stability and rotary derivatives in roll of a model having 45 degrees sweptback wing and tail surfaces. The wing alone and the model without the horizontal tail showed marginal longitudinal stability near maximum lift. The longitudinal stability of the complete model was satisfactory. The vertical tail produced larger increments of rate of change of lateral-force and yawing-moment coefficients with wing-tip helix angle than the fuselage or the horizontal tail.

TAIL-WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1972

Impact of subsonic aerodynamic considerations on a space shuttle booster configuration

Considerations of cruise-back efficiency and subsonic flying qualities are shown to have resulted in a configuration with an aft high wing of moderate aspect ratio and with vertical tails located at the wing tips. The need to protect the air breathing engines during ascent and reentry and the desire for a low trim penalty longitudinal control surface led to consideration of a jet-flap canard. The advantages of this application of STOL technology to a space system are examined and the results of both wind tunnel tests and flight simulations are discussed. Since the use of the jet-flap canard concept offers the potential for a minimum weight vehicle, a proposed technology development program is outlined in order that the full benefit of this concept may be realized.

Roensch, R. L.↗
NASA NTRS1957

Investigation at High Subsonic Speeds of the Static Longitudinal and Lateral Stability Characteristics of Two Canard Airplane Configurations

The present investigation was conducted in the Langley high-speed 7-by 10-foot tunnel to determine the static longitudinal and lateral stability characteristics at high subsonic speeds of two canard airplane configurations previously tested at supersonic speeds. The Mach number range of this investigation extended from 0.60 to 0.94 and a maximum angle-of-attack range of -2dewg to 24deg was obtained at the lowest test Mach number. Two wing plan forms of equal area were studied in the present tests; one was a 60deg delta wing and the other was a trapezoid wing having an aspect ratio of 3, taper ratio of 0.143, and an unswept 80-percent-chord line. The canard control had a trapezoidal plan form and its area was approximately 11.5 percent of the wing area. The model also had a low-aspect-ratio highly swept vertical tail and twin ventral fins. The longitudinal control characteristics of the models were consistent with past experience at low speed on canard configurations in that stalling of the canard surface occurred at moderate and high control deflections for moderate values of angle of attack. This stalling could impose appreciable limitations on the maximum trim-lift coefficient attainable. The control effectiveness and maximum value of trim-lift was significantly increased by addition of a body flap having a conical shape and located slightly behind the canard surface on the bottom of the body. Addition of the canard surface at 0deg deflection had relatively little effect on overall directional stability of the delta-wing configuration; however, deflection of the canard surface from 0deg to 10deg had a large favorable effect on directional stability at high angles of attack for both the trapezoid- and delta-wing configurations.

Sleeman, William C., Jr.↗
NASA NTRS1983

Oil-flow study of a Space Shuttle orbiter tip-fin controller

Possible use of tip-fin controllers instead of a vertical tail on advanced winged entry vehicles was examined. Elimination of the vertical tail and using tip-fins offers the advantages of positive yaw control at high angles of attack and a potential weight savings. Oil-flow technique was used to obtain surface flow patterns on a tip-fin installed on a 0.01-scale Space Shuttle orbiter model for the purpose of assessing the extent of flow interference effects on the wing and tip-fin which might lead to serious heating problems. Tests were conducted in air at Mach 10 for a free-stream Reynolds numbers of .000113 at 20, 30, and 40 degree angle of attack and sideslip angles of 0 and 2 degree. Elevon deflections of -10, 0, and 10 degree and tip-fin control-surface deflections of 0, 20, and 40 degree were employed. Test results were also used to aid in the interpretation of heating data obtained on a Shuttle orbiter tip-fin on another model in a different facility. A limited comparison of oil-flow patterns and heat-transfer data is included. It was determined that elevon deflection angles from -10 to 10 degree and sideslip angles up to 2 degree have very little effect on tip-fin surface flow patterns. Also, there is a minimum of interference between the tip-fin and the wing. The most significant flow interactions occur on the tip-fin onboard surface as a result of its control-surface deflections.

Helms, V. T., III↗
NASA NTRS1973

Pressure loads and aerodynamic force information for the -89A space shuttle orbiter configuration, volume 2

Experimental aerodynamic investigations were conducted on an 0.0405 scale representation of the Rockwell -89A Light Weight Space Shuttle Orbiter. The test purpose was to obtain pressure loads data in the presence of the ground for orbiter structural strength analysis. Aerodynamic force data was also recorded to allow correlation with all pressure loads information. Angles of attack from minus 3 deg to 18 deg and angles of sideslip of 0 deg, plus or minus 50 deg, and plus or minus 10 deg were tested in the presence of the NAAL ground plane. Static pressure bugs were used to obtain a pressure loads survey of the basic configuration, elevon deflections of 5 deg, 10 deg, 15 deg, and minus 20 deg and a rudder deflection of minus 15 deg, at a tunnel dynamic pressure of 40 psi. The test procedure was to locate a maximum of 30 static pressure bugs on the model surface at various locations calculated to prevent aerodynamic and physical interference. Then by various combinations of location the pressure bugs output was to define a complete pressure survey for the fuselages, wing, vertical tail, and main landing gear door.

Mennell, R. C.↗
NASA NTRS1975

Landing pressure loads of the 140A/B space shuttle orbiter (model 43-0) determined in the Rockwell International low speed wind tunnel (OA69), volume 1

Wind tunnel tests of a 0.0405 scale model of the -1404A/B configuration of the Space Shuttle Vehicle Orbiter are presented. Pressure loads data were obtained from the orbiter in the landing configuration in the presence of the ground for structural strength analysis. This was accomplished by locating as many as 30 static pressure bugs at various locations on external model surfaces as each configuration was tested. A complete pressure loads survey was generated for each configuration by combining data from all bug locations, and these loads are described for the fuselage, wing, vertical tail, and landing gear doors. Aerodynamic force data was measured by a six component internal strain gage balance. This data was recorded to correct model angles of attack and sideslip for sting and balance deflections and to determine the aerodynamic effects of landing gear extension. All testing was conducted at a Mach number of 0.165 and a Reynolds number of 1.2 million per foot. Photographs of test configurations are shown.

Soard, T. L.↗
NASA NTRS1993

Aircraft empennage structural detail design

This project involved the detailed design of the aft fuselage and empennage structure, vertical stabilizer, rudder, horizontal stabilizer, and elevator for the Triton primary flight trainer. The main design goals under consideration were to illustrate the integration of the control systems devices used in the tail surfaces and their necessary structural supports as well as the elevator trim, navigational lighting system, electrical systems, tail-located ground tie, and fuselage/cabin interface structure. Accommodations for maintenance, lubrication, adjustment, and repairability were devised. Weight, fabrication, and (sub)assembly goals were addressed. All designs were in accordance with the FAR Part 23 stipulations for a normal category aircraft.

Meholic, Greg↗
NASA NTRS1988

Measurements of pressures on the tail and aft fuselage of an airplane model during rotary motions at spin attitudes

The NASA-Langley Spin Tunnel was used to determine the empennage and aft fuselage surfaces of an aircraft model while it was rotated at spinning-event attitudes, in order to ascertain stern flow conditions and the effects of horizontal tail, as well as the wings, on the vertical tail. A substantial horizontal tail influence is noted on both sides of the vertical tail; the removal of the horizontal tail was found to change the propelling or damping moment characteristics of the vertical tail. The wing was also found to have a large influence on the magnitude of the pressures measured on both the empennage and the aft-fuselage areas.

Hultberg, Randy S.↗
NASA NTRS1959

Estimation of Directional Stability Derivatives at Moderate Angles and Supersonic Speeds

A study of some of the important aerodynamic factors affecting the directional stability of supersonic airplanes is presented. The mutual interference fields between the body, the lifting surfaces, and the stabilizing surfaces are analyzed in detail. Evaluation of these interference fields on an approximate theoretical basis leads to a method for predicting directional stability of supersonic airplanes. Body shape, wing position and plan form, vertical tail position and plan form, and ventral fins are taken into account. Estimates of the effects of these factors are in fair agreement with experiment.

Kaattari, George E.↗
NASA NTRS2013

Wind Tunnel Investigation of Passive Vortex Control and Vortex-Tail Interactions on a Slender Wing at Subsonic and Transonic Speeds

A wind tunnel experiment was conducted in the NASA Langley 8-Foot Transonic Pressure Tunnel to determine the effects of passive porosity on vortex flow interactions about a slender wing configuration at subsonic and transonic speeds. Flow-through porosity was applied in several arrangements to a leading-edge extension, or LEX, mounted to a 65-degree cropped delta wing as a longitudinal instability mitigation technique. Test data were obtained with LEX on and off in the presence of a centerline vertical tail and twin, wing-mounted vertical fins to quantify the sensitivity of the aerodynamics to tail placement and orientation. A close-coupled canard was tested as an alternative to the LEX as a passive flow control device. Wing upper surface static pressure distributions and six-component forces and moments were obtained at Mach numbers of 0.50, 0.85, and 1.20, unit Reynolds number of 2.5 million, angles of attack up to approximately 30 degrees, and angles of sideslip to +/-8 degrees. The off-surface flow field was visualized in cross planes on selected configurations using a laser vapor screen flow visualization technique. Tunnel-to-tunnel data comparisons and a Reynolds number sensitivity assessment were also performed. 15.

Erickson, Gary E.↗
NASA NTRS1986

Investigation of empennage buffeting

Theoretical methods of predicting aircraft buffeting are reviewed. For the buffeting due to leading edge vortex breakdown, a method is developed to convert test data of mean square values of fluctuating normal force to buffeting vortex strength through an unsteady lifting-surface theory and unsteady suction analogy. The resulting buffeting vortex from the leading edge extension of an F-18 configuration is used to generate a fluctuating flow field which produces unsteady pressure distribution on the vertical tails. The root mean square values of root bending moment on the vertical tails are calculated for a rigid configuration.

Lan, C. E.↗
NASA NTRS2005

Development of X-43A Mach 10 Leading Edges

The nose leading edge of the Hyper-X Mach 10 vehicle was orginally anticipated to reach temperatures near 4000 F at the leading-edge stagnation line. A SiC coated carbon/carbon (C/C) leading-edge material will not survive that extreme temperature for even a short duration single flight. To identify a suitable leading edge for the Mach 10 vehicle, arc-jet testing was performed on thirteen leading-edge segments fabricated from different material systems to evaluate their performance in a simulated flight environment. Hf, Zr, Si, and Ir based materials, in most cases as a coating on C/C, were included in the evaluation. Afterwards, MER, Tucson, AZ was selected as the supplier of the flight vehicle leading edges. The nose and the vertical and horizontal tail leading edges were fabricated out of a 3:1 biased high thermal conductivity C/C. The leading edges were coated with a three layer coating comprised of a SiC conversion of the top surface of the C/C, followed by a chemical vapor deposited layer of SiC, followed by a thin chemical vapor deposited layer of HfC. This paper will describe the fabrication of the Mach 10 C/C leading edges and the testing performed to validate performance.

Ohlhorst, Craig W.↗
NASA NTRS1987

Investigation of empennage buffeting

Theoretical methods of predicting aircraft buffeting are reviewed. For the buffeting due to leading-edge vortex breakdown, a method is developed to convert test data of mean square values of fluctuating normal force to buffeting vortex strength through an unsteady lifting-surface theory and unsteady suction analogy. The resulting buffeting vortex from the leading-edge extension of an F-18 configuration is used to generate a fluctuating flow field which produces unsteady pressure distribution on the vertical tails. The root mean square values of root bending moment on the vertical tails are calculated for a rigid configuration. Results from a flow visualization and hot films study in a water tunnel facility using a 1/48 scale model of an F-18 are included in an appendix. The results confirm that the LEX vortex is the dominant forcing function of fin buffet at high angles of attack.

Lan, C. Edward↗
NASA NTRS1991

Wind tunnel investigation of aerodynamic and tail buffet characteristics of leading-edge extension modifications to the F/A-18

The impact of leading-edge extension (LEX) modifications on aerodynamic and vertical tail buffet characteristics of a 16-percent scale F/A-18 model has been investigated in the NASA Langley 30-foot by 60-foot tunnel. Modifications under consideration include variations in LEX chord and span, addition of upper surface fences, and removal of the LEX. Both buffeting and high-angle-of-attack aerodynamics are found to be strongly dependent upon the LEX geometry, which directly influences the strength, position, and breakdown characteristics of the vortex flow field. Concepts aimed at influencing the development of vortical flow field are considered to have much greater potential in design application than those geared toward altering already established flow fields. It is recommended that configuration effects on structural and aerodynamic characteristics be evaluated in parallel, so that trade-off studies can be conducted to ensure adequate structural fatigue life and desired high-angle-of-attack stability and control characteristics in the design of future high performance aircraft.

Shah, Gautam H.↗
NASA NTRS2004

LDV Surveys Over a Fighter Model at Moderate to High Angles of Attack

The vortex flowfield over an advanced twin-tailed fighter configuration was measured in a low-speed wind tunnel at two angles of attack. The primary test data consisted of 3-component velocity surveys obtained using a Laser Doppler Velocimeter. Laser light sheet and surface flow visualization were also obtained to provide insight into the flowfield structure. Time-averaged velocities and the root mean square of the velocity fluctuations were obtained at two cross-sections above the model. At 15 degrees angle of attack, the vortices generated by the wing leading edge extension (LEX) were unburst over the model and passed outboard of the vertical tail. At 25 degrees angle of attack, the vortices burst in the vicinity of the wing-LEX intersection and impact directly on the vertical tails. The RMS levels of the velocity fluctuations reach values of approximately 30% in the region of the vertical tails.

Sellers, William L., III↗
NASA NTRS1973

Application of the control configured vehicle concept to a Space Shuttle configuration.

Potential benefits and limitations of using automatic feedback control systems to provide artificial stabilization, rather than depending on inherent aerodynamic stability are discussed. A conventionally designed Space Shuttle vehicle is used as a baseline. Study results are based on parametric evaluations of configuration changes and control logic concepts suitable for unstable vehicles. Study results show that destabilizing the vehicle by moving the wing forward and reducing vertical tail area reduces the weight of a typical fly-back Space Shuttle booster configuration by 5430 pounds with little or no degradation in control performance. This is accomplished by modifying the aerodynamic controls, but without increasing control surface rate capability or the amount of reaction control fuel carried.

Wawrzyniak, M. E.↗
NASA NTRS2022

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures from a model of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft in the C612A configuration was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for two different mounting options: a swept blade strut that attached at the top of model ahead of the inlet, and rear-entry sting that was made as one piece with a dummy nacelle, and which had a 2”-long cylindrical segment aft of the nozzle exit before tapering up in size. The blade strut allowed for a clean aft end of the model for evaluation of the shocks from that region, while the sting avoided the significant distortions of the flow and shocks from the blade strut along the top of the model. Both the sting and the strut had adapters that attached to a force balance. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail horizontal surface. Off-body static pressure measurements of the flow field below the model were made by use of a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the wind tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the tunnel strut and the balance. The longitudinal positioning allowed multiple pressure signatures to be obtained along different portions of the rail. These signatures were aligned by accounting for the model longitudinal movement and then averaged to take out the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for all the variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗