SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Idaho National Laboratory (INL) has recently compiled a user’s guide for the LightWeight Radioisotope Heating Unit (LWRHU). This guide gives an overview of the LWRHU to potential users. Information and data on mass properties, dimensions, thermal loads, and interfaces are discussed.
Fission power systems have demonstrated higher thermal energy density per unit mass than chemical systems. High mass specific energy density offers advantages in space thermal propulsion applications. In the 1960s, nuclear thermal propulsion (NTP) development included the ROVER/NERVA program, in which full-scale prototype reactors were tested on the ground using hydrogen as the reactor coolant and propellant. NTP systems are being revisited, with expectations of improved performance resulting from improved fuel materials, allowing propellant temperatures near 2,800 K and over 20 thermal propulsion cycles. An apparatus has been developed to test NTP fuel materials in a research reactor at temperature and in a radiation environment typical of the NTP application. Here, this paper presents the design constraints, preliminary scoping thermal analysis, and basic thermal qualification testing for the out-of-pile experiment set apparatus, or OUTSET.
Passive evaporative cooling from a damp cloth or vessel can be used for localized cooling of perishables such as food and medicine, drinking water, and even people. Such applications have two key objectives, which are normally in tension with each other: minimizing the water consumption rate and maximizing the cooling (steady-state temperature swing between the cool cloth and the warm surroundings). Here, we present a simple device that delivers higher performance in both metrics simultaneously by adding a perforated aluminum foil sheet suspended over a stagnant air layer to thermally shield the evaporating surface while also facilitating mass transfer. Experimental results demonstrate a simultaneous 10%–25% increase in temperature swing and 2–3× reduction in water consumption rate as compared to conventional evaporative cooling. This improvement is achieved through careful modeling to optimize the coupled heat and mass transfer through the airgap (thermally insulating and vapor permeable) and perforated foil (infrared reflective and vapor permeable).
A mix of contaminant mass is a known, performance-limiting factor for laser-driven inertial confinement fusion (ICF). It has also recently been shown that the contaminant mass is not necessarily in thermal equilibrium with the deuterium–tritium plasma. Contaminant mass temperature is one of the dominant uncertainties in contaminant mass estimates. The MixIT diagnostic is a new and potentially transformative diagnostic, capable of spatially resolving ion temperature. The approach combines principles of neutron time-of-flight and neutron imaging diagnostics. The information from the MixIT diagnostic can be used to optimize ICF target and laser drive designs as well as provide key constraints on ICF radiation-hydrodynamic simulations that are critical to contaminant mass estimates. This work details the design and optimization of the major components of the MixIT diagnostic: the neutron aperture, the neutron detector (scintillator), and the recording system.
This experimental study investigated the effects of confinement, starting mass, and heating rate on TATB thermal decomposition and sublimation using a combined Thermo-Gravimetric Analyzer and Differential Scanning Calorimetry (TGA/DSC) instrument. The confinement of volatile products was varied using different pinhole sizes with TGA/DSC pans. The measurements showed the open pan experiments without lids/pinholes resulted in complete sublimation of TATB between 320 °C and 360 °C. The heat of sublimation was determined to be 176 kJ/mol (42 kcal /mol), consistent with literature data obtained from other experimental techniques. The use of pinholes suppressed the sublimation of TATB such that the decrease in pinhole size resulted in 1) an increase in the enthalpy of reaction and an increase in the amount of carbonaceous material remaining at the end of decomposition, and 2) convergence of the two peak temperatures corresponding to maximum heat flow and maximum weight loss. Also, a transition from a two-exotherm thermal decomposition behavior towards a single-exotherm occurred as the pinhole size was decreased for a given starting mass or as the starting mass was increased for a given pinhole size. These results indicate the kinetics of TATB sublimation, TATB thermal decomposition, and gas diffusion out of a TGA/DSC pan can all compete and result in significantly different enthalpies, amounts of remaining materials, and peak temperatures depending on the pinhole size and starting mass used in the measurements. Furthermore, the results also indicate precise control of process variables (pinhole size, starting mass, and heating rate) in TGA/DSC measurements is required for thermal safety assessment of explosives.
Knowledge of the degradation kinetics for polymer materials is important for understanding thermal stability. In this study, evolved gas analysis–mass spectrometry and pyrolysis gas-chromatography-mass spectrometry were evaluated for the potential to deliver additional insight into thermal degradation kinetics of diglycidal ether of bisphenol F (DGEBF) epoxy thermoset under inert and oxidative atmospheres. Degradation products of selected precursor ions were evaluated for their uniqueness to the specific precursor using extracted ion thermographs. Unique mass peaks, solely attributed to a single reaction pathway of a specific product, were determined from extracted ion thermographs and used to determine both activation energy (E a ) and pre-exponential factors for the specific primary reaction pathways. These primary reaction pathways for DGEBF epoxy degradation were then evaluated in the context of transition state theory (TST) and related transition state enthalpies (ΔH ‡ ) and entropies (ΔS ‡ ) of activation to further elucidate the degradation process. It was determined under pyrolysis conditions, as suggested by the E a , the formation of bisphenol F monomer was the rate-limiting step toward the formation of xanthene and phenol. In contrast, under thermo-oxidative conditions, reactions involving oxygen containing species were identified as the rate-limiting step for all observed products based on the large negative ΔS ‡ calculated from TST. This work demonstrates a powerful combination of technique and theory that can provide new insight into the degradation of polymer materials.
Not Available
Not provided.
Recent observational and large eddy simulation (LES) modeling studies have nearly unanimously supported the view of deep cumulus convection being composed of a series of quasi-spherical bubbles of buoyant air, known as moist thermals. Despite the prevalence of moist thermals in deep convection, a comprehensive theory for the dynamics of these structures is lacking. Most current conceptual models for cumulus convection are based on canonical scaling theories for dry thermals or plumes; however, there is considerable evidence that the behavior of moist thermals differs markedly from these theories. Furthermore, the theoretical basis for most cumulus parameterizations originates from the plume conceptual model, and therefore these parameterizations are inconsistent with the real structure of moist convection. Motivated by the aforementioned knowledge gaps, this “end-to-end” research effort use theory, observations, numerical simulations, and direct improvements to the Zhang-McFarlane (ZM) convection scheme in the global climate Community Atmosphere Model (CAM) to address the following research questions: What key environmental parameters determine whether or not shallow convection will transition into deep convection, in the context of thermal-like updrafts? What factors regulate the size of thermals within cumulus updrafts? How does vertical wind shear influence thermal behavior, and as a consequence, vertical velocity and mass flux profiles and the shallow-to-deep convective transition? What are the critical processes that determine updraft vertical velocities and their connection to the vertical mass flux profile for thermal-like updrafts? Idealized LES modeling will be used in conjunction with theoretical models for the core properties of thermal-like updrafts to better understand key processes that regulate thermal ascent rates and entrainment properties. Thermal-tracking procedures will be used to characterize the behavior of thermals within the LES, and recently developed direct measures of entrainment and detrainment will be used to quantify entrainment/detrainment rates. Building from these results, we will analyze the structure of moist thermals from hemispheric range-height indicator scans taken during the Atmospheric Radiation Measurement Cloud, Aerosol, and Complex Terrain Interactions (CACTI) field campaign, and from “real case” LES of CACTI events. This combined modeling and observational analysis will provide essential validation for the existing body of research on moist thermal dynamics, which is based primarily on modeling studies. With the insight gained from the aforementioned activities, we will modify the Zhang-McFarlane convection scheme to improve its representation of updraft vertical velocity and entrainment rate profiles. These process-level changes will be tested in the Community Atmosphere Model to assess the impact on global climate simulations.
Abstract We extend the Effective Field Theory of Heavy Dark Matter to arbitrary odd representations of SU(2) and incorporate the effects of bound states. This formalism is then deployed to compute the gamma-ray spectrum for a5of SU(2): quintuplet dark matter. Except at isolated values of the quintuplet mass, the bound state contribution to hard photons with energy near the dark-matter mass is at the level of a few percent compared to that from direct annihilation. Further, compared to smaller representations, such as the triplet wino, the quintuplet can exhibit a strong variation in the shape of the spectrum as a function of mass. Using our results, we forecast the fate of the thermal quintuplet, which has a mass of ~13.6 TeV. We find that existing H.E.S.S. data should be able to significantly test the scenario, however, the final word on this canonical model of minimal dark matter will likely be left to the Cherenkov Telescope Array (CTA).
Recent advances in manufacturing technologies have enabled the fabrication of complex geometries for a wide range of applications, including the energy, aerospace, and civil sectors. The ability to integrate sensors at critical locations within these complex components during the manufacturing process could benefit process monitoring and control by reducing reliance on models to relate surface measurements to internal phenomena. This study investigated embedding thermocouples in a SS316 matrix using laser powder bed fusion. Under optimal processing conditions, embedded thermocouples were characterized post-building, finding good bonding to the matrix with no melt pool penetration to the sensing elements. Futher, the embedded thermocouple performed similarly to an identical non-embedded thermocouple during thermal testing to 500 °C with only a slight difference in response time, which was attributed to the differences in mass and the associated thermal time constants.
Analysis of byproducts from thermal degradation of polymer materials provides a wealth of information about a materials’ composition, thermal stability, degradation mechanisms, and kinetics. However, regardless of the instrumentation used, only limited information is obtainable from a single experiment. Microfurnace technology, when interfaced to a gas chromatography-mass spectrometry (GC-MS), can be used to obtain both thermal and chemical information via evolved gas analysis-MS (EGA-MS) and GC-MS analysis modes. While both EGA-MS and Py-GC-MS are valuable when characterizing polymer materials, at least two experiments on distinct samples are required, which can be a liability for clear interpretation of results from inhomogeneous samples. Here, we seek to overcome this limitation by combining EGA-MS and Py-GC-MS modes in a single experimental setup. Further, this was done by developing new gas line modifications to allow for tandem Pyrolysis Evolved Gas-Gas Chromatography-Mass Spectrometry (Py/EG-GC-MS) analysis. Verification of Py/EG-GC-MS analysis was performed using a polystyrene standard. Results demonstrate successful Py/EG-GC-MS analysis for the first-time showing the potential of these modifications for application in areas where sample is limited or direct correlation of products to the thermal profile is desirable such as in forensics or product-specific kinetics.
Here, in this study, we examined the effect of gamma radiation on the stabilities of aluminum hydroxide (gibbsite) and aluminum oxyhydroxide (boehmite) nanoparticles in relation to their thermal decomposition. X-ray diffraction (XRD) patterns and scanning electron microscopy (SEM) images revealed no significant differences in mineral components or morphology before and after radiation. However, thermogravimetric and differential scanning calorimetry (TGA/DSC) analyses showed that both boehmite and gibbsite nanoparticles experienced decreased mass loss following irradiation. Raman and attenuated total reflection-Fourier transfer infrared (ATR-FTIR) spectra indicated that a fraction of the hydroxyl content in both cases was selectively cleaved by radiation, primarily at the particle surfaces. Quantitative analyses of thermal mass loss behavior demonstrated that irradiated boehmite and gibbsite nanoparticles had higher activation energies than their pristine counterparts, with the extent of the increase dependent on the total dose. Taken together, these findings suggest that exposure to a sufficient dose of ionizing radiation alters these materials such that they are less prone to decomposition by dehydration. This increased stability may be due to the decreased hydrous nature of the samples after radiation exposure, which was supported by further high temperature drop calorimetry. Additionally, a radiation-induced amorphous phase on the nanoparticle surfaces appears to have a permanent and positive influence on their thermodynamic stabilities.
Phase change material heat exchangers (PCM-HX) can be used as a latent heat thermal energy storage (LHTES) component in heat pump applications to further enhance the efficiency of a heat pump as well as to yield financial savings by peak-load shifting. In this paper, a low-cost commercially available aluminum serpentine heat exchanger with louvered fins was experimentally investigated to check its thermal performance as a PCM-HX. A transparent rectangular box fabricated from acrylic plates served as a PCM container. Two cameras were used to capture the phase change process of the PCM on the front and top sides of the container during the experiment. A total of 88 installed temperature sensors throughout the test setup and a mass flow meter enabled a quantitative analysis of the PCM-HX as well. The energy balance deviation between the estimated theoretical and experimentally calculated PCM storage was ±14% considering the often-neglected heat loss and thermal mass of the PCM-HX. PCM temperature profiles, charge and discharge rates, and energy densities under different test conditions were also investigated.
Thermal stability of organic–inorganic hybrid perovskites (OIHPs) remains as one of the critical challenges against the stable operation of perovskite solar cells (PSCs) in direct sunlight with elevated temperatures. Here, we show that the addition of a polystyrene-co-polyacrylonitrile (SAN) copolymer can significantly enhance thermal stability of OIHPs and improve the stability of the corresponding PSCs by suppressing the migration of organic cations in OHIP. The methylammonium lead iodide (MAPI) with SAN incorporated within the perovskite layer featured a superior thermal stability compared to pure MAPI without SAN, only displaying an average of 5–15% decrease in PCE even after continuous thermal aging for 24 h at 100 °C. The secondary ion mass spectrometry revealed that the thermal degradation of the pure MAPI was largely associated with MA+ out-migration. Conducting atomic force microscopy analysis further indicated that the incorporated SAN led to a suppression of ionic currents present at the grain boundaries of the perovskite film, which was understood by high immiscibility between SAN and MA+ components as confirmed by the experimentally estimated Flory–Huggins parameter between them. This study newly identifies a potential of using polymer grain encapsulation for enhancing thermal stability of OIHPs and their solar cell performance by suppressing the out-diffusion of cationic organic components.
The EIC will make use of the existing RHIC storage rings with their superconducting (SC) magnet arcs. A stain-less-steel beam screen with co-laminated copper and a thin amorphous carbon (aC) film on the inner surface will be installed in the beam pipe of the SC magnets. The copper will reduce the beam-induced resistive-wall (RW) heating from operation with the higher intensity EIC beams, that if not addressed would make the magnets quench. Limiting the RW heating is also important to achieve an adequately low vacuum level. The aC coating will reduce secondary electron yield which could also cause heating and limit in-tensity. Among all the RHIC SC magnets, the arc dipoles present the biggest challenge to the design and installation of beam screens. The arc dipoles, which make up for 78% (2.5 km) length of all SC magnets in RHIC, expect the larg-est RW heating due to their smallest aperture. These mag-nets are also the longest (9.45 m each), thus experiencing the largest temperature rise over their length, and have a large sagitta (48.5 mm) that increases the difficulty to in-stall the beam screen in place. This paper presents a de-tailed thermal analysis of the magnet-screen system.
The analysis of thermally labile and high-boiling point compounds by gas chromatography (GC) can be a challenge. One technique to overcome these challenges is low-pressure GC, which uses the vacuum produced from the mass spectrometer and wide-bore columns to elute compounds at significantly lower temperatures. While GC-MS is a powerful technique, comprehensive two-dimensional gas chromatography (GC × GC), allows for resolution of compounds that would typically coelute using GC. Here, in this study, a pesticide standard mixture (8270 MegaMix Standard) was analyzed using a conventional GC × GC-TOFMS configuration (0.25 mm inner diameter (i.d.) to a 0.18 mm i.d. column) and low-pressure GC × GC-TOFMS configuration (0.53 mm i.d. to a 0.53 mm i.d. column). Elution temperatures, sensitivity, and peak capacity were investigated for both configurations. Compounds eluted an average of 30 °C less on the low-pressure GC × GC-TOFMS configuration compared to the conventional GC × GC-TOFMS configuration. Moreover, the compounds were separated in ~13 min on the low-pressure GC × GC-TOFMS as opposed to 33 min for conventional GC × GC-TOFMS. However, due to the wide-bore columns and faster runtimes the low-pressure GC × GC-TOFMS had a lower, β corrected 2D peak capacity, n c,β,2D , of 1260 while the conventional GC × GC-TOFMS was 3588. Interestingly, both configurations yielded a similar peak capacity production of 93 peaks/min and 107 peaks/min for low-pressure and conventional GC × GC-TOFMS, respectively. A “real world” sample of diesel fuel was tested on the low-pressure and conventional GC × GC-TOFMS configurations and similar results were obtained compared to the pesticide standard mix except the peak capacity production of the low-pressure GC × GC-TOFMS configuration was higher than that of the conventional GC × GC-TOFMS method.
Abstract. The Differential Emissivity Imaging Disdrometer (DEID) is a new evaporation-based optical and thermal instrument designed to measure the mass, size, density and type of individual hydrometeors as well as their bulk properties. Hydrometeor spatial dimensions are measured on a heated metal plate using an infrared camera by exploiting the much higher thermal emissivity of water compared with metal. As a melted hydrometeor evaporates, its mass can be directly related to the loss of heat from the hotplate assuming energy conservation across the hydrometeor. The heat loss required to evaporate a hydrometeor is found to be independent of environmental conditions including ambient wind velocity, moisture level and temperature. The difference in heat loss for snow vs. rain for a given mass offers a method for discriminating precipitation phase. The DEID measures hydrometeors at sampling frequencies of up to 1 Hz with masses and effective diameters greater than 1 µg and 200 µm, respectively, determined by the size of the hotplate and the thermal camera specifications. Measurable snow water equivalent (SWE) precipitation rates range from 0.001 to 200 mm h−1, as validated against a standard weighing bucket. Preliminary field experiment measurements of snow and rain from the winters of 2019 and 2020 provided continuous automated measurements of precipitation rate, snow density and visibility. Measured hydrometeor size distributions agree well with canonical results described in the literature.