Search NASA⌕ Search

SEARCH · Search NASA

Results for “TIMING PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Turbulence characteristics of the noise producing region of an excited round jet. I - Time-average flow properties

Experiments were conducted to determine the mean turbulence characteristics of the noise-producing region of a 3 in. cold excited round jet. The jet was excited by plane acoustic waves with a high amplitude of excitation (2 percent of the jet dynamic head), and at a Strouhal number of 0.5. The flow Reynolds number was 280,000. The exit boundary layer was made turbulent by artificially tripping it with sandpaper strips. The data were obtained with single and X-hot-wires and processed in digital form. Mean and higher order statistics were also deduced. The results showed an increase in all three velocity components and stresses. However, most of the increase was noticed from the longitudinal component, while the changes in the radial velocity and the azimuthal component were much smaller. Substantial widening of the jet occurred, accompanied by a shortening of the potential core. Increased rates of production of energy close to the lip-line were a characteristic feature of the mixing region behavior.

Baltas, C.↗

External control of the Saturn kilometric radiation by the solar wind - Comparison between Voyager 1 and 2 observations

The long-term modulation of Saturn's nonthermal radio emission in the kilometric wavelength range has been studied based upon data obtained by Voyagers 1 and 2. A comparison of the ballistic and hydrodynamic propagation of solar wind features from the spacecraft to Saturn allows the uncertainty inherent in the projection to be determined. The results confirm the previous suggestion that momentum, ram pressure, and kinetic energy flux are the primary solar wind parameters that drive the nonthermal radio emission. It is suggested that, under certain conditions and for limited periods of time, the magnetic properties and time derivatives of the solar wind have increased importance.

Rucker, H. O.↗

Time domain convergence properties of Lyapunov stable penalty methods

Linear hyperbolic partial differential equations are analyzed using standard techniques to show that a sequence of solutions generated by the Liapunov stable penalty equations approaches the solution of the differential-algebraic equations governing the dynamics of multibody problems arising in linear vibrations. The analysis does not require that the system be conservative and does not impose any specific integration scheme. Variational statements are derived which bound the error in approximation by the norm of the constraint violation obtained in the approximate solutions.

Kurdila, A. J.↗

Scaling properties of induction times in heterogeneous nucleation

The heterogeneous-to-homogeneous induction time ratio is obtained as a function of the contact angle in the asymptotic limit of a high nucleation barrier. Model-dependent corrections to t(ind) are investigated, particularly in cases of the Turnbull-Fisher model used in numerical simulations by Greer et al. (1990).

Shneidman, Vitaly A.↗

Physical properties and evolutionary time scales of disks around solar-type and intermediate mass stars

Recent observations of circumstellar disks and their evolutionary timescales are reviewed. It is concluded that disks appear to be a natural outcome of the star-formation process. The disks surrounding young stars initially are massive, with optically thick structures comprised of gas and micron-sized grains. Disk masses are found to range from 0.01 to 0.2 solar masses for solar-type PMS stars, and from 0.01 to 6 solar masses for young, intermediate mass stars. Massive, optically thick accretion disks have accretion rates between 10 exp -8 and 10 exp -6 solar masses/yr for solar type PMS stars and between 10 exp -6 and 10 exp -4 solar masses/yr for intermediate stars. The results suggest that a significant fraction of the mass comprising the star may have passed through a circumstellar accretion disk.

Strom, Stephen E.↗

Statistical properties of the time histories of cosmic gamma-ray bursts detected by the BATSE experiment of the Compton gamma-ray observatory

The main scientific objectives of the project were: (1) Calculation of average time history for different subsets of BATSE gamma-ray bursts; (2) Comparison of averaged parameters and averaged time history for different Burst And Transient Source Experiments (BASTE) Gamma Ray Bursts (GRB's) sets; (3) Comparison of results obtained with BATSE data with those obtained with APEX experiment at PHOBOS mission; and (4) Use the results of (1)-(3) to compare current models of gamma-ray bursts sources.

Sagdeev, Roald↗

Variable thermal properties and thermal relaxation time in hyperbolic heat conduction

Numerical solutions were obtained for a finite slab with an applied surface heat flux at one boundary using both the hyperbolic (MacCormack's method) and parabolic (Crank-Nicolson method) heat conduction equations. The effects on the temperature distributions of varying density, specific heat, and thermal relaxation time were calculated. Each of these properties had an effect on the thermal front velocity (in the hyperbolic solution) as well as the temperatures in the medium. In the hyperbolic solutions, as the density or specific heat decreased with temperature, both the temperatures within the medium and the thermal front velocity increased. The value taken for the thermal relaxation time was found to determine the 'hyperbolicity' of the heat conduction model. The use of a time dependent relaxation time allowed for solutions where the thermal energy propagated as a high temperature wave initially, but approached a diffusion process more rapidly than was possible with a constant large relaxation time.

Glass, David E.↗

Variation of solar-selective properties of black chrome with plating time

The spectral reflectance properties of a commercially prepared black chrome over dull nickel, both plated on steel, for various plating times of the black chrome were measured. The plating current was 180 amperes per square foot. Values of absorptance integrated over the solar spectrum, and of infrared emittance integrated over black-body radiation at 250 F were obtained. It is shown that plating between one and two minutes produces the optimum combination of highest heat absorbed and lowest heat lost by radiation.

Mcdonald, G. E.↗

Issues in measure-preserving three dimensional flow integrators: Self-adjointness, reversibility, and non-uniform time stepping

Properties of integration schemes for solenoidal fields in three dimensions are studied, with a focus on integrating magnetic field lines in a plasma using adaptive time stepping. It is shown that implicit midpoint (IM) and a scheme we call three-dimensional leapfrog (LF) can do a good job (in the sense of preserving KAM tori) of integrating fields that are reversible, or (for LF) have a “special divergence-free” (SDF) property. We review the notion of a self-adjoint scheme, showing that such schemes are at least second order accurate and can always be formed by composing an arbitrary scheme with its adjoint. We also review the concept of reversibility, showing that a reversible but not exactly volume-preserving scheme can lead to a fractal invariant measure in a chaotic region, although this property may not often be observable. We also show numerical results indicating that the IM and LF schemes can fail to preserve KAM tori when the reversibility property (and the SDF property for LF) of the field is broken. We discuss extensions to measure preserving flows, the integration of magnetic field lines in a plasma and the integration of rays for several plasma waves. The main new result of this paper relates to non-uniform time stepping for volume-preserving flows. We investigate two potential schemes, both based on the general method of Feng and Shang [Numer. Math. 71, 451 (1995)], in which the flow is integrated in split time steps, each Hamiltonian in two dimensions. The first scheme is an extension of the method of extended phase space, a well-proven method of symplectic integration with non-uniform time steps. This method is found not to work, and an explanation is given. The second method investigated is a method based on transformation to canonical variables for the two split-step Hamiltonian systems. This method, which is related to the method of non-canonical generating functions of Richardson and Finn [Plasma Phys. Controlled Fusion 54, 014004 (2012)], appears to work very well.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Non-destructive thermal wave method applied to study thermal properties of fast setting time endodontic cement

The thermal wave method is applied for thermal properties measurement in fast endodontic cement (CER). This new formula is developed upon using Portland cement in gel and it was successfully tested in mice with good biocompatibility and stimulated mineralization. Recently, thermal expansion and setting time were measured, conferring to this material twice faster hardening than the well known Angelus Mineral trioxide aggregate (MTA) the feature of fast hardening (∼7 min) and with similar thermal expansion (∼12 μstrain/ °C). Therefore, it is important the knowledge of thermal properties like thermal diffusivity, conductivity, effusivity in order to match thermally the tissue environment upon its application in filling cavities of teeth. Photothermal radiometry technique based on Xe illumination was applied in CER disks 600 μm thick for heating, with prepared in four particle sizes (25, 38, 45, and 53) μm, which were added microemulsion gel with variation volumes (140, 150, 160, and 170) μl. The behavior of the thermal diffusivity CER disks shows linear decay for increase emulsion volume, and in contrast, thermal diffusivity increases with particles sizes. Aiming to compare to MTA, thermal properties of CER were averaged to get the figure of merit for thermal diffusivity as (44.2 ± 3.6) × 10{sup −3} cm{sup 2}/s, for thermal conductivity (228 ± 32) mW/cm K, the thermal effusivity (1.09 ± 0.06) W s{sup 0.5}/cm{sup 2} K and volume heat capacity (5.2 ± 0.7) J/cm{sup 3} K, which are in excellent agreement with results of a disk prepared from commercial MTA-Angelus (grain size < 10 μm using 57 μl of distilled water)

36 MATERIALS SCIENCE↗

Unipolar time-differential charge sensing in non-dispersive amorphous solids

The use of high resistivity amorphous solids as photodetectors, especially amorphous selenium, is currently of great interest because they are readily produced over large area at substantially lower cost compared to grown crystalline solids. However, amorphous solids have been ruled out as viable radiation detection media for high frame-rate applications, such as single-photon-counting imaging, because of low carrier mobilities, transit-time-limited photoresponse, and consequently, poor time resolution. To circumvent the problem of poor charge transport in amorphous solids, we propose unipolar time-differential charge sensing by establishing a strong near-field effect using an electrostatic shield within the material. For the first time, we have fabricated a true Frisch grid inside a solid-state detector by evaporating amorphous selenium over photolithographically prepared multi-well substrates. The fabricated devices are characterized with optical, x-ray, and gamma-ray impulse-like excitations. Results prove the proposed unipolar time-differential property and show that time resolution in non-dispersive amorphous solids can be improved substantially to reach the theoretical limit set by spatial spreading of the collected Gaussian carrier cloud.

36 MATERIALS SCIENCE↗

Separation of time scales in aircraft trajectory optimization

Two methods for analyzing the time-scale properties of aircraft trajectory optimization problems are presented. Time-scale properties must be identified before solutions can be obtained by using singular perturbation methods. Both methods only require a knowledge of the state equations, the aircraft characteristics, and the bounds on the state and control variables. Although these methods give only rough estimates of time-scale separation, they do not require that an 'exact' optimal trajectory be known, as do the more rigorous methods, and they are an improvement on the ad hoc methods currently in use. The two methods are applied to an example problem for a high performance aircraft.

Ardema, M. D.↗

Using heterogeneous data to identify signatures of dengue outbreaks at fine spatio-temporal scales across Brazil

Dengue virus remains a significant public health challenge in Brazil, and seasonal preparation efforts are hindered by variable intra- and interseasonal dynamics. Here, we present a framework for characterizing weekly dengue activity at the Brazilian mesoregion level from 2010–2016 as time series properties that are relevant to forecasting efforts, focusing on outbreak shape, seasonal timing, and pairwise correlations in magnitude and onset. In addition, we use a combination of 18 satellite remote sensing imagery, weather, clinical, mobility, and census data streams and regression methods to identify a parsimonious set of covariates that explain each time series property. The models explained 54% of the variation in outbreak shape, 38% of seasonal onset, 34% of pairwise correlation in outbreak timing, and 11% of pairwise correlation in outbreak magnitude. Regions that have experienced longer periods of drought sensitivity, as captured by the “normalized burn ratio,” experienced less intense outbreaks, while regions with regular fluctuations in relative humidity had less regular seasonal outbreaks. Both the pairwise correlations in outbreak timing and outbreak trend between mesoresgions were best predicted by distance. Our analysis also revealed the presence of distinct geographic clusters where dengue properties tend to be spatially correlated. Forecasting models aimed at predicting the dynamics of dengue activity need to identify the most salient variables capable of contributing to accurate predictions. Our findings show that successful models may need to leverage distinct variables in different locations and be catered to a specific task, such as predicting outbreak magnitude or timing characteristics, to be useful. This advocates in favor of “adaptive models” rather than “one-size-fits-all” models. The results of this study can be applied to improving spatial hierarchical or target-focused forecasting models of dengue activity across Brazil.

59 BASIC BIOLOGICAL SCIENCES↗

Effect of Retrogression Heat Treatment Time on Microstructure and Mechanical Properties of AA7010

The effect of retrogression time during retrogression and re-aging (RRA) treatment of AA7010 is evaluated by performing tensile tests and characterizing the microchemistry of the grain boundary precipitates (GBPs) using transmission electron microscope coupled with the energy-dispersive spectroscopy. Retrogression time is evaluated so that the ultimate tensile strength of the RRA-treated sample is equal to that of the T6-treated sample and the grain boundary microstructure similar to that of the over-aged (T7451) condition. The investigation reveals that the sample retrogressed at 200 °C for 20 min has UTS of 586 MPa which is equivalent to that of the T6 sample and 11.5% higher than that of the T7451 condition. The fracture toughness of the RRA-treated sample was 41 MPa√m. Microstructure of the RRA-treated sample is similar to T7451, along the grain boundaries and in the grain interior similar to that of the T6-treated sample. Energy-dispersive spectroscopy confirmed the increment of Cu content on the GBP’s with increase in the retrogression time, which is expected to improve the stress corrosion cracking resistance of the alloy.

36 MATERIALS SCIENCE↗

Influence of Hydrogen Plasma Treatment Time to Si:H Layer Deposition Time Ratio on the Properties of Layer-by-Layer Deposited Hydrogenated Silicon (Si:H) Thin Films

Hydrogenated silicon (Si-H) thin films were deposited from a mixture of pure silane (SiH{sub 4}) and hydrogen (H{sub 2}) gases in a home-built plasma enhanced chemical vapour deposition (PECVD) system using the layer-by-layer (LBL) deposition technique. In the LBL process, the deposition was performed by periodically alternating the deposition of Si:H layer with the hydrogen treatment process of the growth surface. In this work, the effects of the H plasma treatment time to Si-H layer growth time ratio on the film properties were studied. The LBL deposited Si-H films studied in this work were deposited using different Si-H layer growth times ranging from 2 minutes to 7 minutes with the hydrogen plasma treatment time on the growth surface fixed at 3 minutes. Optical transmission spectroscopy, X-ray diffraction (XRD), micro-Raman scattering spectroscopy, Fourier transform infrared (FTIR) spectroscopy and atomic force microscopy (AFM) measurements were done on these films to investigate the optical, structural and morphological properties of the films. The films deposited by this technique produced the highest deposition rate of 6.3 A ring /s when the growth time of the Si-H layer was fixed at 5 minutes. These films were amorphous in structure and had large optical energy gaps irrespective of the Si-H layer deposition time. High concentration of cone-like structures was observed in the AFM images for the films deposited using the higher Si-H layer deposition times.

36 MATERIALS SCIENCE↗

National forest timber bids and export price interlinkages in the USA: The bounds testing approach

We examine the interrelationships of national forest timber bid and log export prices for Douglas-fir (Region 6) in 2003–2021 and loblolly pine (Region 8) using time-series stationarity and bounds-testing approaches. The analysis shows the difference in time series properties across different geographies and time scales. Bid prices for these dominant species of timber in each of two Forest Service regions are found to be stationary, while log export prices for those same species appear to be non-stationary. Bounds testing conducted with autoregressive distributed lag modeling methods provides strong evidence for a cointegrating relationship between timber bid prices and log export prices in Forest Service Region 6. In Region 8, evidence for a cointegrating relationship was weak. Here, the share of salvage wood in national forest timber sales is a statistically significant control variable in all models estimated.

54 ENVIRONMENTAL SCIENCES↗