Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tensile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Improved Creep and Tensile Properties of a Corrosion Resistant Ni-Based Superalloy Using High Temperature Aging and Nb/Ta Additions

Resistance to creep deformation is essential for cast and wrought Ni-based superalloys in next generation energy systems due to the considerable exposure times required at the operating temperature. Here the amount of precipitate strengthening was increased in variants to Inconel alloy 725 (IN725), a corrosion resistant alloy, to improve its elevated temperature mechanical strength. Additions of Nb or Ta coupled with a high temperature aging (HTA) heat treatment promoted the formation of γ" precipitates and grain boundary phases which led to significant increases in time to failure. The HTA increased the creep life of various alloy formulations as compared to the standard aging heat treatment with a maximum improvement of 371%. The Nb and Ta additions lowered the minimum creep rate (MCR) and had a similar effect on increasing creep life. The positive effect of the additions was more pronounced when coupled with the HTA which employed a higher temperature in the first step of the heat treatment to promote precipitate phase formation. The Ti/Al ratio was used to design alloys with preferential formation of ' or γ" precipitates. Compact morphology precipitates were formed in the alloys with a low Ti/Al ratio. While a low Ti/Al ratio was primarily associated with lower MCRs, the effect on the creep life was less evident than that of the HTA. By using additions of Nb or Ta and a HTA heat treatment, the creep life of IN725 for testing at 973 K (700 °C) and 483 MPa was improved by up to 256%.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding and quantifying electron beam effects during in situ TEM nanomechanical tensile testing on metal thin films

Transmission electron microscopy (TEM) imaging relies on high energy electrons for atomic scale resolution, however, the electrons themselves interact with and may alter the material being imaged. Using an in situ TEM MEMS-based nanomechanical testing technique, the effect of the electron beam (e-beam) on the deformation behavior of nanocrystalline Al and ultrafine-grained Au is investigated and quantified. We show that the e-beam enhances plastic deformation, leading to an increase in plastic strain rate and a decrease in true activation volume V* in Al (28 to 21b 3 , with b being the Burgers vector length). The e-beam has a much weaker effect on Au. The e-beam effect is not caused by knock-on damage, but rather an effective temperature increase due to additional atomic fluctuations provided by the e-beam. The effective temperature increase is larger for Al than Au. This e-beam effect does not change the deformation mechanisms, but instead accelerates the stress-driven, thermally activated plastic deformation. These experiments provide insight into the effects of the e-beam on plastic deformation in different metals and underscore the importance of understanding and quantifying these effects for proper interpretation of measured mechanical properties during in situ TEM experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Simulation of axial tensile well deformation during reservoir compaction in offshore unconsolidated methane hydrate-bearing formation

Sand production encountered in the 2013 offshore field gas production tests at the Nankai Trough, Japan, could be attributed to well failure during reservoir compaction. In this study, well integrity under various reservoir compaction patterns for the Nankai Trough case is examined using a well-formation finite element model. Here, the modelling details include the inclusion of a cement sheath as well as the modelling of construction processes (such as cement shrinkage). Well elongation in the overburden layer becomes significant when the reservoir subsidence is localized near the wellbore under large depressurization. Results show that the maximum plastic deviatoric strain level in the cement could reach 0.7% when the maximum reservoir subsidence reaches 0.85 m and cement shrinkage is limited. When cement shrinkage rises to 0.75%, the maximum plastic deviatoric strain increases to 2.4% as the cement accumulates additional plastic strain during shrinkage due to its deformation being constrained by the casing. In order to prevent the cement from failure, it might be effective to hold the pressure drawdown at a low level (e.g., several MPa) until the hydrate dissociation front advances to a certain radius from the well (e.g., a couple of tens of metres).

58 GEOSCIENCES↗
DOE OSTI2022

Mode I tensile fracture behavior of adhesively-bonded metal–metal, metal–CFRP, and CFRP–CFRP bi-material combinations analyzed by size effect method

Understanding the adhesive and interfacial fracture is important for developing and achieving better adhesive jointing in bi-materials, the location which becomes less vulnerable in engineered structure components. Still, to characterize the fracturing behavior of various adhesively-bonded materials, it was shown in this work that the Mode I fracture energies estimated from conventional methods (e.g., work-of-fracture, (modified) compliance calibration method, (modified) beam theory, etc.) can be strongly affected by adherent thickness, adhesive bond length, and material type. Consequently, this hindered the proper understanding of fracturing in adhesive jointing of bi-materials since the estimated fracture energies can exhibit unreasonable difference among various material combinations, thus leading to the confusion in the literature due to the unfair comparison on these non-objective results estimated by leveraging conventional methods on the specimens with different geometries. This work compared size effect method with conventional methods on the calculation of the Mode I fracture energies of metal-metal, metal-CFRP, and CFRP-CFRP material combinations via Double Cantilever Beam (DCB) tests. The results showed that the estimated fracture energies of various material combinations are not dependent on the specimen geometries. This aspect allowed the fair comparison particularly on the interfacial fracturing between metal/adhesive and CFRP/adhesive, and the difference was further explained and correlated with the damage morphology on the material surface after failure identified through three-dimensional profilometer.

36 MATERIALS SCIENCE↗